RSG DOS06-05T-P Non-isolated point of load dc/dc converter Datasheet

1
FEATURES
APPLICATIONS
Wireless Network
Telecom/Datacom
Industry Control System
Distributed Power Architectures
Semiconductor Equipment
Microprocessor Power Applications
Positive Logic Remote on/off
DESCRIPTION
DOS06-05T (SMD type), DOH06-05T (for Vertical Mounting SIP type) and
DOH06-05TA (for Horizontal Mounting SIP type) are non-isolated DC/DC
converters that can deliver up to 6A of output current with full load efficiency of 94%
at 3.3V output.
All specifications are typical at nominal input, full load and 25ºC otherwise noted
OUTPUT SPECIFICATIONS
Voltage accuracy
Full load and Vin(nom.)
Minimum load
Line regulation
INPUT SPECIFICATIONS
6A max. Input voltage range
± 2%Vo(set) Maximum input current
0%
Vin=Vo(set)+0.5V to Vin(max.)
at Full Load
Load regulation
No Load to Full Load
Ripple and noise (Note2) 20MHz bandwidth
Temperature coefficient
3
OPTIONS
T E C H N I C A L S P E C I F I C AT I O N
Output current
/
• OUTPUT CURRENT UP TO 6A
• SMALL SIZE AND LOW PROFILE :
0.80” X 0.45” X 0.22” (SMD) ; 0.9” X 0.40” X 0.20” (SIP)
• HIGH EFFICIENCY - 94% @ 3.3V FULL LOAD
• INPUT RANGE FROM 2.4VDC TO 5.5VDC
• FIXED SWITCHING FREQUENCY (300KHZ)
• SMD & SIP PACKAGES
• OUTPUT VOLTAGE PROGRAMMABLE FROM 0.75VDC TO 3.3VDC
VIA EXTERNAL RESISTOR
• INPUT UNDER-VOLTAGE LOCKOUT
• UL60950-1, EN60950-1 AND IEC60950-1 LICENSED
• ISO9001 CERTIFIED MANUFACTURING FACILITIES
• COMPLIANT TO RoHS EU DIRECTIVE 2002/95/EC
Vo(set) < Vin – 0.5V
2.4 – 5.5VDC
Vin=Vin(min.); Vo(set)=3.3V; Io=Io(max.)
Input filter (Note 5)
6A
C filter
± 0.3%Vo(set),typ. Input no load current
Vo(set) =0.75Vdc
20mA,typ.
45mA,typ.
(Vin=5V, Io=0, module enabled)
Vo(set) =3.3Vdc
± 0.4%Vo(set),typ.
Start-up voltage
2.2V,typ.
20mVrms,max. Input under voltage lockout
2.0V,typ.
Shutdown voltage
50mVp-p,max.
Input reflected ripple current 5~20MHz, 1μH source impedance 35mAp-p
±0.4%, typ.
Peak deviation 130mV,typ. ENVIRONMENTAL SPECIFICATIONS
Setting time
Operating ambient temperature
–40ºC ~ +85ºC(with derating)
(Vo<10%peak
25μS,typ.
deviation)
Storage temperature range
–55ºC ~ +125ºC
Peak deviation 50mV,typ.
Thermal shock
MIL-STD-810F
Setting time
(Vo<10%peak
50μS,typ. Over temperature protection
135 ºC, typ.
deviation)
220%,typ. FEATURE SPECIFICATIONS
Output short-circuit current
Hiccup, automatics recovery Remote ON/OFF(Note 6)
ON = 0V < Vr < 0.3V
IIN=10μA, max.
(Negative logic)(standard)
ESR≧1mΩ
1000μF,max.
External load capacitance
OFF =1.5V < Vr < Vin(max)
IIN=1mA, max.
3000μF,max.
ESR≧10mΩ
(Positive logic)(option)
ON = Vin(max)
IIN=10μA, max.
Output voltage overshoot-startup Vin=2.4~5.5V, F.L.
1%Vo(set)
OFF=0V < Vr < 0.3V
IIN=1mA, max.
Voltage adjustability (see fig.1) (Note 4)
0.7525V ~ 3.63V Input current of Remote control pin
10μA~1.0mA
Remote off state input current Nominal Vin
0.6mA,typ.
ΔIo /Δt = 2.5A/μS ,Vin(nom.)
Load change step
(50% to 100% or
100% to 50% of Io(max.))
ΔIo /Δt = 2.5A/μS ,Vin(nom)
Dynamic load
Load change step
response
(50% to 100% or
(Note3)
100% to 50% of Io(max.))
Output current limit
Dynamic load
response
(Note2)
GENERAL SPECIFICATIONS
See table Rise time
Efficiency
Isolation voltage
None Turn-on delay time
300KHz, typ.
Switching frequency
Approvals and standard
IEC60950-1, UL60950-1, EN60950-1
0.80 X 0.45 X 0.22 Inch
(20.3 X 11.4 X 5.5 mm)
SIP
0.90 X 0.40 X 0.20 Inch
(22.9 X 10.2 X 5.0 mm)
2.8g(0.1oz)
7
BELLCORE TR-NWT-000332
2.133 x 10 hrs
6
3.247 x 10 hrs
MIL-HDBK-217F
SMD
Dimensions
Weight
MTBF (Note 1)
Time for Vo to rise from 10% to 90%of Vo(set)
Case 1 (Note 7)
Case 2 (Note 8)
6ms,max.
1ms, typ.
1ms, typ.
2
Model Name
ON/OFF
Logic
DOS06-05T
DOS06-05T-P
DOH06-05T
DOH06-05T-P
DOH06-05TA
DOH06-05TA-P
Negative
Positive
Negative
Positive
Negative
Positive
Package
Input Voltage
Output Voltage
Output Current
Efficiency (%)
Min. Load Max. Load
5.0Vin, 3.3Vdc@6A
/
SMD
2.4 ~ 5.5Vdc
Vertical Mounting
Vin(min.)=Vo(set)+0.5V
SIP
Horizontal Mounting
SIP
0.75 ~ 3.3Vdc
0A
6A
94%
Note
1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC.
MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment).
2. External with Cout = 1μF ceramic//10μF tantalum capacitors.
3. External with Cout = 2×150uF polymer capacitors.
4. Output voltage programmable from 0.75V to 3.3V by connecting a single resistor (shown as Rtrim in Table 1) between the TRIM and GND pins of the
module.To calculate the value of the resistor Rtrim for a particular output voltage Vo, use the following equation:
Rtrim =
[
21070
Vo – 0.7525
-5110
]Ω
5.
It’s necessary to equip the external input capacitors at the input of the module. The capacitors should connect as close as possible to the input
terminals that ensuring module stability. The external Cin is 2×150μF low-ESR polymer capacitors // 2×47μF ceramic capacitors at least.
6. Device code with suffix “-P” – Positive logic(On/Off is open collector/drain logic input; Signal referenced to GND )
Device code with no suffix – Negative logic (On/Off pin is open collector/drain logic input with external pull –up resistor; signal referenced to GND)
7. Case 1 :On/Off input is set to logic low (module on) and then input power is applied (delay from instant at which Vin=Vin(min) until Vo=10% of Vo(set))
8. Case 2 :Input power is applied for at least one second and then the On/Off input is set to logic low (delay form instant at which Von/off=0.3V until
Vo=10% of Vo(set))
CAUTION: This power module is not internally fused. An input line fuse must always be used.
DOS06-05T, Vo=3.3V, Derating Curve
OUTPUT CURRENT,Io(A)
7
6
5
4
3
2
1
0
20
30
40
50
6063
70
80
90
AMBIENT TEMPERATURE,TA(℃)
Fig. 1
Table 1
Vo(set) (V)
Rtrim (KΩ)
0.7525
Open
1.2
41.973
1.5
23.077
1.8
15.004
2.5
6.974
3.3
3.160
3
3
DOH06-05T
0.20(5.0)
0.13(3.3)
VOUT
TRIM
GND
VIN
ON/OFF
0.40(10.2)
0.90(22.9)
0.025(0.64)
0.05(1.3)
0.100(2.54)
0.035(0.88)
0.600(15.24)
0.16(4.12)
0.700(17.78)
0.800(20.32)
BOTTOM VIEW
SIDE VIEW
DOH06-05TA
VOUT
TRIM
GND
VIN
ON/OFF
BOTTOM VIEW
SIDE VIEW
DOS06-05T
BOTTOM VIEW
SIDE VIEW
1. All dimensions in Inches (mm)
Tolerance: X.XX±0.02 (X.X±0.5)
X.XXX±0.01 (X.XX±0.25)
2. Pin pitch tolerance ±0.01(0.25)
3. Pin dimension tolerance ±0.004 (0.1)
Last update:2008/6/4
/
3
Similar pages