LINER LT1168AIS8 Low power, single resistor gain programmable, micropower precision instrumentation amplifier Datasheet

LT1168
Low Power, Single
Resistor Gain Programmable,
Precision Instrumentation Amplifier
DESCRIPTIO
U
FEATURES
The LT ®1168 is a micropower, precision instrumentation amplifier that requires only one external resistor to set gains of
1 to 10,000. The low voltage noise of 10nV/√Hz (at 1kHz) is
not compromised by low power dissipation (350µA typical for
±15V supplies). The wide supply range of ±2.3V to ±18V allows
the LT1168 to fit into a wide variety of industrial as well as
battery-powered applications.
The high accuracy of the LT1168 is due to a 20ppm maximum
nonlinearity and 0.4% max gain error (G = 10). Previous monolithic instrumentation amps cannot handle a 2k load resistor
whereas the nonlinearity of the LT1168 is specified for loads
as low as 2k. The LT1168 is laser trimmed for very low input
offset voltage (40µV max), drift (0.3µV/°C), high CMRR (90dB,
G = 1) and PSRR (103dB, G = 1). Low input bias currents of
250pA max are achieved with the use of superbeta processing. The output can handle capacitive loads up to 1000pF in
any gain configuration while the inputs are ESD protected up
to 13kV (human body). The LT1168 with two external 5k
resistors passes the IEC 1000-4-2 level 4 specification.
The LT1168 is a pin-for-pin improved second source for the
AD620 and INA118. The LT1168, offered in 8-pin PDIP and
SO packages, requires significantly less PC board area than
discrete op amp resistor designs. These advantages make
the LT1168 the most cost effective solution for precision
instrumentation amplifier applications.
Supply Current: 530µA Max
Meets IEC 1000-4-2 Level 4 (±15kV) ESD Tests
with Two External 5k Resistors
Single Gain Set Resistor: G = 1 to 10,000
Gain Error: G = 10, 0.4% Max
Input Offset Voltage Drift: 0.3µV/°C Max
Gain Nonlinearity: G = 10, 20ppm Max
Input Offset Voltage: 40µV Max
Input Bias Current: 250pA Max
PSRR at AV =1: 103dB Min
CMRR at AV = 1: 90dB Min
Wide Supply Range: ±2.3V to ±18V
1kHz Voltage Noise: 10nV/√Hz
0.1Hz to 10Hz Noise: 0.28µVP-P
Available in 8-Pin PDIP and SO Packages
■
■
■
■
■
■
■
■
■
■
■
■
■
■
U
APPLICATIO S
■
■
■
■
■
■
■
■
■
Bridge Amplifiers
Strain Gauge Amplifiers
Thermocouple Amplifiers
Differential to Single-Ended Converters
Differential Voltage to Current Converters
Data Acquisition
Battery-Powered and Portable Equipment
Medical Instrumentation
Scales
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Single Supply* Pressure Monitor
1
3
8
3.5k
3.5k
3.5k
+
40k
7
REF
R1
G = 200
249Ω
6
LT1168
1
2
5
–
4
IN
ADC
LTC®1286
20k
3
40k
2
+
1/2
LT1112
1
DIGITAL
DATA
OUTPUT
NONLINEARITY (100ppm/DIV)
5V
3.5k
Gain Nonlinearity
BI TECHNOLOGIES
67-8-3 R40KQ, (0.02% RATIO MATCH)
AGND
–
1168 TA01
G = 1000
RL = 2k
VOUT = ±10V
OUTPUT VOLTAGE (2V/DIV)
1168 TA01a
*See Theory of Operation section
1
LT1168
W W
W
AXI U
U
ABSOLUTE
RATI GS
U
U
W
PACKAGE/ORDER I FOR ATIO
(Note 1)
Supply Voltage ...................................................... ±20V
Differential Input Voltage (Within the
Supply Voltage) ..................................................... ±40V
Input Voltage (Equal to Supply Voltage) ................ ±20V
Input Current (Note 2) ....................................... ±20mA
Output Short-Circuit Duration (Note 3) ............ Indefinite
Operating Temperature Range (Note 4) .. – 40°C to 85°C
Specified Temperature Range
LT1168AC/LT1168C (Note 5) ............. – 40°C to 85°C
LT1168AI/LT1168I ............................. – 40°C to 85°C
Storage Temperature Range ................. – 40°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
ORDER PART
NUMBER
TOP VIEW
RG 1
8
RG
–IN 2
–
7
+VS
+IN 3
+
6
OUTPUT
5
REF
–VS 4
LT1168ACN8
LT1168ACS8
LT1168AIN8
LT1168AIS8
LT1168CN8
LT1168CS8
LT1168IN8
LT1168IS8
N8 PACKAGE
8-LEAD PDIP
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 150°C/ W (N8)
TJMAX = 150°C, θJA = 190°C/ W (S8)
S8 PART MARKING
1168A
1168AI
1168
1168I
Consult factory for Military grade parts.
ELECTRICAL CHARACTERISTICS
SYMBOL
G
TA = 25°C. VS = ±15V, VCM = 0V, RL = 10k unless otherwise noted.
PARAMETER
CONDITIONS (Note 6)
Gain Range
G = 1 + (49.4k/RG)
Gain Error
G=1
G = 10 (Note 7)
G = 100 (Note 7)
G = 1000 (Note 7)
Gain Nonlinearity (Notes 7, 8)
LT1168AC/LT1168AI
MIN
TYP
MAX
1
10k
LT1168C/LT1168I
MIN
TYP
MAX
1
UNITS
10k
0.008
0.04
0.04
0.08
0.02
0.4
0.5
0.5
0.015
0.05
0.05
0.08
0.03
0.5
0.6
0.6
%
%
%
%
VO = ±10V, G = 1
VO = ±10V,G = 10 and 100
VO = ±10V, G = 1000
2
10
20
6
20
40
3
15
25
10
25
60
ppm
ppm
ppm
VO = ±10V, G = 1, RL = 2k
VO = ±10V,G = 10 and 100, RL = 2k
VO = ±10V, G = 1000, RL = 2k
4
20
40
15
40
75
5
30
50
20
60
90
ppm
ppm
ppm
VOST
Total Input Referred Offset Voltage VOST = VOSI + VOSO/G
VOSI
Input Offset Voltage
G = 1000, VS = ±5V to ±15V
15
40
20
60
µV
VOSO
Output Offset Voltage
G = 1, VS = ±5V to ±15V
40
200
50
300
µV
IOS
Input Offset Current
50
300
60
450
pA
IB
Input Bias Current
40
250
80
500
pA
en
Input Noise Voltage, RTI
0.1Hz to 10Hz, G = 1
0.1Hz to 10Hz, G = 1000
Input Noise Voltage Density, RTI
fO = 1kHz
in
RIN
2
2.00
0.28
µVP-P
µVP-P
2.00
0.28
10
15
10
15
nV/√Hz
Output Noise Voltage Density, RTI fO = 1kHz (Note 9)
Input Noise Current
fO = 0.1Hz to 10Hz
165
220
165
220
nV/√Hz
5
5
pAP-P
Input Noise Current Density
fO = 10Hz
74
74
fA/√Hz
Input Resistance
VIN = ±10V
300
1250
200
1250
GΩ
LT1168
ELECTRICAL CHARACTERISTICS
TA = 25°C. VS = ±15V, VCM = 0V, RL = 10k unless otherwise noted.
LT1168AC/LT1168AI
MIN
TYP
MAX
LT1168C/LT1168I
MIN
TYP
MAX
fO = 100kHz
1.6
1.6
pF
Common Mode Input
Capacitance
fO = 100kHz
1.6
1.6
pF
Input Voltage Range
G = 1, Other Input Grounded
VS = ±2.3V to ±5V
VS = ±5V to ±18V
SYMBOL PARAMETER
CONDITIONS (Note 6)
CIN(DIFF)
Differential Input Capacitance
CIN(CM)
VCM
CMRR
+VS – 1.2
+VS – 1.4
–VS + 1.9
–VS + 1.9
+VS – 1.2
+VS – 1.4
V
V
1k Source Imbalance,
VCM = 0V to ±10V
G=1
G = 10
G = 100
G = 1000
90
106
120
126
95
115
135
140
85
100
110
120
95
115
135
140
dB
dB
dB
dB
Power Supply
Rejection Ratio
VS = ±2.3V to ±18V
G=1
G = 10
G = 100
G = 1000
103
122
131
135
108
128
145
150
100
118
126
130
108
128
145
150
dB
dB
dB
dB
IS
Supply Current
VS = ±2.3V to ±18V
VOUT
Output Voltage Swing
RL = 10k
VS = ±2.3V to ±5V
VS = ±5V to ±18V
PSRR
Common Mode
Rejection Ratio
–VS + 1.9
–VS + 1.9
UNITS
IOUT
Output Current
BW
Bandwidth
G=1
G = 10
G = 100
G = 1000
SR
Slew Rate
G = 1, VOUT = ±10V
Settling Time to 0.01%
10V Step
G = 1 to 100
G = 1000
REFIN
Reference Input Resistance
IREFIN
Reference Input Current
VREF
Reference Voltage Range
AVREF
Reference Gain to Output
350
–VS + 1.1
–VS + 1.2
20
530
+VS – 1.2
+VS – 1.3
32
–VS + 1.1
–VS + 1.2
20
+VS – 1.2
+VS – 1.3
V
V
32
mA
kHz
kHz
kHz
kHz
0.5
V/µs
30
200
30
200
µs
µs
60
60
kΩ
0.5
VREF = 0V
µA
400
200
13
1
400
200
13
1
0.3
530
350
0.3
18
–VS + 1.6
µA
18
+VS – 1.6
–VS + 1.6
1 ± 0.0001
+VS – 1.6
V
1 ± 0.0001
The ● denotes the specifications which apply over the 0°C ≤ TA ≤ 70°C temperature range. VS = ±15V, VCM = 0V, RL = 10k unless
otherwise noted.
SYMBOL PARAMETER
∆G/∆T
CONDITIONS (Note 6)
MIN
LT1168AC
TYP
MAX
MIN
LT1168C
TYP
MAX
UNITS
Gain Error
G=1
G = 10 (Note 7)
G = 100 (Note 7)
G = 1000 (Note 7)
●
●
●
●
0.01
0.40
0.45
0.50
0.03
1.5
1.6
1.7
0.012
0.500
0.550
0.600
0.04
1.6
1.7
1.8
%
%
%
%
Gain Nonlinearity
(Notes 7, 8)
VOUT = ±10V, G = 1
VOUT = ±10V, G = 10 and 100
VOUT = ±10V, G = 1000
●
●
●
2
7
25
15
30
60
3
10
30
20
35
80
ppm
ppm
ppm
Gain vs Temperature
G < 1000 (Note 7)
●
100
200
100
200
ppm/°C
3
LT1168
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the 0°C ≤ TA ≤ 70°C
temperature range. VS = ±15V, VCM = 0V, RL = 10k unless otherwise noted.
SYMBOL PARAMETER
CONDITIONS (Note 6)
MIN
LT1168AC
TYP
MAX
60
VOST
Total Input Referred Offset Voltage
VOSI
Input Offset Voltage
VS = ±5V to ±15V
●
18
VOSIH
Input Offset Voltage Hysteresis
(Notes 7, 10)
●
3.0
VOSO
Output Offset Voltage
VS = ±5V to ±15V
●
60
MIN
LT1168C
TYP
MAX
23
80
UNITS
VOST = VOSI + VOSO/G
µV
µV
3.0
380
70
500
µV
µV
VOSOH
Output Offset Voltage Hysteresis (Notes 7, 10)
●
30
VOSI/T
Input Offset Drift (RTI)
(Note 9)
●
0.05
0.3
0.06
0.4
µV/°C
VOSO/T
Output Offset Drift
(Note 9)
●
0.7
3
0.8
4
µV/°C
400
120
550
IOS
Input Offset Current
●
100
IOS/T
Input Offset Current Drift
●
0.3
IB
Input Bias Current
●
65
IB/T
Input Bias Current Drift
●
1.4
VCM
Input Voltage Range
30
0.4
350
105
pA
pA/°C
600
1.4
pA
pA/°C
G = 1, Other Input Grounded
VS = ±2.3V to ±5V
VS = ±5V to ±18V
●
●
–VS + 2.1
–VS + 2.1
1k Source Imbalance,
VCM = 0V to ±10V
G=1
G = 10
G = 100
G = 1000
●
●
●
●
88
100
115
117
92
110
120
135
83
97
113
114
92
110
120
135
dB
dB
dB
dB
Power Supply
Rejection Ratio
VS = ±2.3V to ±18V
G=1
G = 10
G = 100
G = 1000
●
●
●
●
102
123
127
129
115
130
135
145
98
118
124
126
115
130
135
145
dB
dB
dB
dB
IS
Supply Current
VS = ±2.3V to ±18V
●
VOUT
Output Voltage Swing
RL = 10k
VS = ±2.3V to ±5V
VS = ±5V to ±18V
●
●
–VS + 1.4
–VS + 1.6
●
16
25
0.48
CMRR
PSRR
Common Mode
Rejection Ratio
+VS – 1.3 –VS + 2.1
+VS – 1.4 –VS + 2.1
390
IOUT
Output Current
SR
Slew Rate
G = 1, VOUT = ±10V
●
0.25
VREF
Voltage Range
(Note 9)
●
–VS + 1.6
615
+VS – 1.3
+VS – 1.4
390
+VS – 1.3 –VS + 1.4
+VS – 1.5 –VS + 1.6
16
0.25
V
V
615
µA
+VS – 1.3
+VS – 1.5
V
V
25
mA
0.48
V/µs
+VS – 1.6 –VS + 1.6
+VS – 1.6
V
The ● denotes the specifications which apply over the – 40°C ≤ TA ≤ 85°C temperature range. VS = ±15V, VCM = 0V, RL = 10k unless
otherwise noted. (Note 8)
SYMBOL PARAMETER
MIN
LT1168AI
TYP
MAX
MIN
LT1168I
TYP
MAX
UNITS
Gain Error
G=1
G = 10 (Note 7)
G = 100 (Note 7)
G = 1000 (Note 7)
●
●
●
●
0.014
0.600
0.600
0.600
0.04
1.9
2.0
2.1
0.015
0.700
0.700
0.700
0.05
2.0
2.1
2.2
%
%
%
%
GN
Gain Nonlinearity
(Notes 7, 8)
VO = ±10V, G = 1
VO = ±10V, G = 10 and 100
VO = ±10V, G = 1000
●
●
●
3
10
30
20
35
70
5
15
35
25
40
100
ppm
ppm
ppm
∆G/∆T
Gain vs Temperature
G < 1000 (Note 7)
●
100
200
100
200
ppm/°C
4
CONDITIONS (Note 6)
LT1168
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the – 40°C ≤ TA ≤ 85°C
temperature range. VS = ±15V, VCM = 0V, RL = 10k unless otherwise noted. (Note 5)
SYMBOL PARAMETER
CONDITIONS (Note 6)
MIN
LT1168AI
TYP
MAX
LT1168I
TYP
MAX
UNITS
75
25
100
µV
500
200
600
µV
MIN
VOST
Total Input Referred Offset Voltage
VOSI
Input Offset Voltage
VOSIH
Input Offset Voltage Hysteresis
●
3.0
VOSO
Output Offset Voltage
●
180
VOSOH
Output Offset Voltage Hysteresis (Notes 7, 10)
●
30
VOSI/T
Input Offset Drift (RTI)
(Note 9)
●
0.05
0.3
0.06
0.4
µV/°C
VOSO/T
Output Offset Drift
(Note 9)
●
0.8
5
1
6
µV/°C
IOS
Input Offset Current
●
110
550
120
700
IOS/T
Input Offset Current Drift
●
0.3
IB
Input Bias Current
●
120
500
220
IB/T
Input Bias Current Drift
●
1.4
VCM
Input Voltage Range
VS = ±2.3V to ±5V
VS = ±5V to ±18V
●
●
–VS + 2.1
–VS + 2.1
CMRR
Common Mode
Rejection Ratio
1k Source Imbalance,
VCM = 0V to ±10V
G=1
G = 10
G = 100
G = 1000
●
●
●
●
86
98
114
116
90
105
118
133
81
95
112
112
90
105
118
133
dB
dB
dB
dB
VS = ±2.3V to ±18V
G=1
G = 10
G = 100
G = 1000
●
●
●
●
100
120
125
128
112
125
132
140
95
115
120
125
112
125
132
140
dB
dB
dB
dB
PSRR
Power Supply
Rejection Ratio
IS
Supply Current
VOUT
Output Voltage Swing
IOUT
VOST = VOSI + VOSO/G
20
●
(Notes 7, 10)
VS = ±2.3V to ±5V
VS = ±5V to ±18V
µV
30
0.3
–VS + 2.1
–VS + 2.1
650
pA
pA/°C
+VS – 1.3
+VS – 1.4
420
650
µA
+VS – 1.3
+VS – 1.5
V
V
–VS + 1.4
–VS + 1.6
Output Current
●
15
22
15
22
mA
SR
Slew Rate
●
0.22
0.41
0.22
0.42
V/µs
VREF
Voltage Range
●
–VS + 1.6
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be imparied.
Note 2: If the input voltage exceeds the supplies, the input current should
be limited to less than 20mA.
Note 3: A heat sink may be required to keep the junction temperature
below absolute maximum.
Note 4: The LT1168AC/LT1168C are guaranteed functional over the
operating temperature range of – 40°C and 85°C.
Note 5: The LT1168AC/LT1168C are guaranteed to meet specified
performance from 0°C to 70°C. The LT1168AC/LT1168C are designed,
characterized and expected to meet specified performance from – 40°C to
85°C but are not tested or QA sampled at these temperatures. The
LT1168AI/LT1168I are guaranteed to meet specified performance from
– 40°C to 85°C.
+VS – 1.6
–VS + 1.4
–VS + 1.6
V
V
●
●
(Note 9)
+VS – 1.3
+VS – 1.5
pA
pA/°C
800
1.4
+VS – 1.3
+VS – 1.4
420
●
µV
3.0
–VS + 1.6
+VS – 1.6
V
Note 6: Typical parameters are defined as the 60% of the yield parameter
distribution.
Note 7: Does not include the tolerance of the external gain resistor RG.
Note 8: This parameter is measured in a high speed automatic tester that
does not measure the thermal effects with longer time constants. The
magnitude of these thermal effects are dependent on the package used,
heat sinking and air flow conditions.
Note 9: This parameter is not 100% tested.
Note 10: Hysteresis in offset voltage is created by package stress that
differs depending on whether the IC was previously at a higher or lower
temperature. Offset voltage hysteresis is always measured at 25°C, but
the IC is cycled to 85°C I-grade (or 70°C C-grade) or – 40°C I-grade
(0°C C-grade) before successive measurement. 60% of the parts will
pass the typical limit on the data sheet.
5
LT1168
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Distribution of Output Offset
Voltage
60
VS = ±15V
55 T = 25°C
A
50 G = 1000
299 N8 (2 LOTS)
337 S0-8 (2 LOTS)
636 TOTAL PARTS
45
PERCENT OF UNITS (%)
40
35
30
25
20
15
40
35
30
25
20
15
10
5
5
40
–20
0
20
–40
INPUT OFFSET VOLTAGE (µV)
1168 G01
20
15
10
5
5
VS = ±15V
40 TA = 30°C
G=1
30 4 PARTS FROM 4 LOTS
20 WARMED UP
10
0
–10
–20
–30
–40
–50
–0.35 –0.25 –0.15 –0.05 0.05
INPUT OFFSET VOLTAGE DRIFT (µV/°C)
1
0
–1
–2
–3
–4
–5
0
2
1
TIME (MONTHS)
0
3
2
1
TIME (MONTHS)
3
1168 G05
60
VS = ±15V
TA = 25°C
G=1
50
1168 G05
Voltage Noise Density
vs Frequency
VS = ±15V
TA = 25°C
G = 1000
40
25
SO-8
GAIN (dB)
CHANGE IN TOTAL INPUT REFERRED
OFFSET VOLTAGE (µV)
VS = ±15V
4 TA = 30°C
G = 1000
3 4 PARTS FROM 4 LOTS
2 WARMED UP
Gain vs Frequency
20
15
N-8
10
30
G = 100
20
G = 10
10
0
G=1
5
–10
0
1
2
3
4
TIME AFTER POWER-ON (MINUTES)
0.2
–0.6
–0.2
–1.0
–1.4
OUTPUT OFFSET VOLTAGE DRIFT (µV/°C)
1168 G03
50
Warm-Up Drift
5
–20
0.01
1000
1/f CORNER = 2Hz
GAIN = 1
1
10
FREQUENCY (kHz)
100
1000
VS = ±15V
TA = 25°C
100
1/f CORNER = 7Hz
GAIN = 10
GAIN = 100, 1000
10
1/f CORNER = 3Hz
BW LIMIT
GAIN = 100
BW LIMIT
GAIN = 1000
1
0.1
1168 G08
1168 G07
6
10
Input Offset Voltage
Long-Term Drift
1168 G04
0
15
0
–1.8
60
CHANGE IN INPUT OFFSET VOLTAGE (µV)
CHANGE IN OUTPUT OFFSET VOLTAGE (µV)
PERCENT OF UNITS (%)
VS = ±15V
T = –40°C TO 85°C
30 GA= 1000
97 N8 (2 LOTS)
25 49 S0-8 (1 LOT)
146 TOTAL PARTS
30
20
Output Offset Voltage
Long-Term Drift
35
35
25
1168 G02
Distribution of Input Offset
Voltage Drift
0
–0.45
97 N8 (2 LOTS)
49 S0-8 (1 LOT)
146 TOTAL PARTS
5
0
–60
150
VS = ±15V
TA = –40°C TO 85°C
30 G = 1
45
10
0
100
0
50
–150 –100 –50
OUTPUT OFFSET VOLTAGE (µV)
35
299 N8 (2 LOTS)
337 S0-8 (2 LOTS)
636 TOTAL PARTS
VOLTAGE NOISE DENSITY (nV/√Hz)
PERCENT OF UNITS (%)
VS = ±15V
55 T = 25°C
A
50 G = 1
Distribution of Output Offset
Voltage Drift
PERCENT OF UNITS (%)
60
Distribution of Input Offset
Voltage
1
10
100
1k
FREQUENCY (Hz)
10k
100k
1168 G09
LT1168
U W
TYPICAL PERFOR A CE CHARACTERISTICS
0.1Hz to 10Hz Noise Voltage,
G=1
0.1Hz to 10Hz Noise Voltage,
RTI G = 1000
Current Noise Density
vs Frequency
1000
CURRENT NOISE DENSITY (fA/√Hz)
VS = ±15V
TA = 25°C
NOISE VOLTAGE (2µV/DIV)
NOISE VOLTAGE (0.2µV/DIV)
VS = ±15V
TA = 25°C
VS = ±15V
TA = 25°C
RS
100
1/f CORNER = 55Hz
10
1
2
3
4 5 6
TIME (SEC)
7
8
9
1
0
10
2
3
4 5 6
TIME (SEC)
7
8
1168 G10
9
Short-Circuit Current vs Time
50
OUTPUT CURRENT (mA)
(SINK)
(SOURCE)
NOISE CURRENT (5pA/DIV)
Output Impedance vs Frequency
1k
VS = ±15V
40
TA = 25°C
20
10
TA = 85°C
0
– 10
TA = 85°C
– 20
– 30
TA = 25°C
– 40
TA = – 40°C
– 50
1
2
3
4 5 6
TIME (SEC)
7
8
9
70
60
50
G=1
40
30
VS ±15V
TA = 25°C
G = 10
20
20
10
G = 100, 1000
10
100
1000
CAPACITIVE LOAD (pF)
10000
1168 G16
10k
100k
FREQUENCY (Hz)
0
–200
+IB
+IB
1M
1168 G15
Input Offset Current
30
10
0
1k
50
302 N8 (2 LOTS)
313 SO-8 (2 LOTS)
615 TOTAL PARTS
40
OUTPUT VOLTAGE (V)
OVERSHOOT (%)
50
VS = ±15V
VOUT = ± 50mV
RL = ∞
80
1
Input Bias Current
Overshoot vs Capacitive Load
90
10
1168 G14
1168 G13
100
100
0.1
2
1
0
3
TIME FROM OUTPUT SHORT TO GROUND (MINUTES)
10
VS = ±15V
TA = 25°C
40
PERCENT OF UNITS (%)
0
VS = ± 15V
TA = 25°C
G = 1 TO 1000
TA = – 40°C
30
1000
1168 G12
1168 G11
0.1Hz to 10Hz Current Noise
VS = ±15V
TA = 25°C
10
100
FREQUENCY (Hz)
1
10
OUTPUT IMPEDANCE (Ω)
0
302 N8 (2 LOTS)
313 SO-8 (2 LOTS)
615 TOTAL PARTS
30
20
10
–IB
–120
40
120
–40
INPUT BIAS CURRENT (pA)
200
1168 G17
0
–120
–80
0
40
80
–40
INPUT OFFSET CURRENT (pA)
120
1168 G18
7
LT1168
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Change in Input Bias Current for
VCM = 20V
10
302 N8 (2 LOTS)
313 SO-8 (2 LOTS)
615 TOTAL PARTS
6
14
12
10
RINCM = 5TΩ
RINCM = 700GΩ
8
6
4
VOUT
0V
0V
–2
VOUT
–4
–6
–8
–10
0
TO 0.01%
0
2
4
8 12 16 20 24 28 32 34
CHANGE IN INPUT BIAS CURRENT (pA)
TO 0.1%
1
SETTLING TIME (µs)
G = 100, FALLING EDGE
26
VS = ± 15V
TA = 25°C
RL = 1k
STEP SIZE = 10V
G = 10,
RISING EDGE
22
20
18
16
10
30
100
300
LOAD CAPACITANCE (pF)
400
Falling Edge Settling Time
(0.10%)
VS = ±15V
VCM = 0V
300
200
0
–5
0.10
–10
0.05
0
0.05
–5
0.10
IOS
100
0
0
IB
–100
–200
–10
–300
5µs/DIV
–400
–500
–75 –50 –25
1000
0
25 50
TEMPERATURE
75
Rising Edge Settling Time
(0.10%)
100 125
Settling Time (0.01%)
vs Load Capacitance
Undistorted Output Swing
vs Frequency
35
0.05
VOUT (V)
0
10
0.05
5
0.10
5µs/DIV
t=0
TA = 25°C
VS = ±15V
RL = 2k
CL = 15pF
1168 G25
G = 100,
RISING EDGE
PEAK-TO-PEAK OUTPUT SWING (V)
0.10
0
32
SETTLING TIME (µs)
5
8
G = 100,
FALLING EDGE
34
SETTLING (%)
VIN (V)
36
10
1168 G24
t=0
TA = 25°C
VS = ±15V
RL = 2k
CL = 15pF
1168 G23
1168 G22
0
1000
1168 G21
VIN (V)
G = 1, RISING EDGE
G = 10,
FALLING EDGE
100
GAIN
VOUT (V)
G = 1, FALLING EDGE
G = 100,
RISING EDGE
10
SETTLING (%)
INPUT BIAS AND OFFSET CURRENT (pA)
500
24
1
8 10 12 14 16 18 20 22 24 26 28 30 32
SETTLING TIME (µs)
Input Bias and Offset Current
vs Temperature
34
28
10
1168 G20
Settling Time (0.1%)
vs Load Capacitance
30
100
TO 0.01%
1168 G19
32
VS = ± 15V
TA = 25°C
∆VOUT = 10V TO 0.01%
TO 0.1%
2
4
0
VS = ±15
G=1
TA = 25°C
CL = 30pF
RL = 1k
8
OUTPUT STEP (V)
PERCENT OF UNITS (%)
VS = ±15V
18 VCM = ±10V
TA = 25°C
16
Settling Time vs Gain
1000
SETTLING TIME (µs)
20
Settling Time vs Step Size
G = 1, RISING EDGE
30
28
G = 10, FALLING EDGE
26
24
G = 10, RISING EDGE
22
VS = ± 15V
TA = 25°C
RL = 1k
STEP SIZE = 10V
20
18
10
G = 1,
FALLING
EDGE
30
100
300
LOAD CAPACITANCE (pF)
30
G = 10, 100, 1000
25
G=1
VS = ±15V
TA = 25°C
20
15
10
5
0
1000
1168 G26
1
10
100
FREQUENCY (kHz)
1000
1168 G27
LT1168
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Input Voltage Range vs Output
Voltage for Various Gains
VS = ± 15V
85°C
25°C
– 40°C
+ VS – 1.0
INPUT VOLTAGE RANGE WITH RESPECT TO
NEGATIVE SUPPLY (–VS + VIN)
+ VS
+ VS – 0.5
+ VS – 1.5
+ VS – 2.0
+ VS – 2.5
– VS + 2.5
– VS + 2.0
– VS + 1.5
– VS + 1.0
– VS + 0.5
– VS
0.01
0.1
1
10
OUTPUT CURRENT (mA)
100
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
–15
VS = ±15V
TA = 25°C
G=1
G=2
VOUT = –VS + 1.2V
G = 100
G = 10
G = 100
G = 10
G=2
VOUT = +VS – 1.3V
G=1
–VCM = –VS + 1.9V
–11
–7
3
–3
VOUT (V)
7
11
1168 G28
Slew Rate vs Temperature
1.0
VS = ±15V
0.8
SINKING CURRENT
SLEW RATE (V/µs)
OUTPUT CURRENT (mA)
50
40
30
SOURCING CURRENT
VS = ±15V
VOUT = ±10V
G=1
0.6
+SLEW
–SLEW
0.4
0.2
20
10
–50
–25
50
25
0
TEMPERATURE (°C)
75
0
–50
100
–25
50
25
0
TEMPERATURE (°C)
1168 G31
5V/DIV
20mV/DIV
5V/DIV
50µs/DIV
100
Large-Signal Transient Response
Small-Signal Transient Response
Large-Signal Transient Response
75
1168 G30
1168 G29
G=1
VS = ±15V
RL = 2k
CL = 60pF
15
1168 G43
Output Short-Circuit Current
vs Temperature
60
0
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
–11
–12
–13
–14
–15
+VCM = +VS – 1.4V
INPUT VOLTAGE RANGE WITH RESPECT TO
POSITIVE SUPPLY (+VS – VIN)
OUTPUT VOLTAGE SWING (V)
REFERRED TO SUPPLY VOLTAGE
(SINK)
(SOURCE)
Output Voltage Swing vs
Load Current
G=1
VS = ±15V
RL = 2k
CL = 60pF
10µs/DIV
1168 G32
G = 10
VS = ±15V
RL = 2k
CL = 60pF
50µs/DIV
1168 G33
9
LT1168
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Small-Signal Transient Response
Small-Signal Transient Response
20mV/DIV
5V/DIV
20mV/DIV
Large-Signal Transient Response
1168 G34
50µs/DIV
G = 100
VS = ±15V
RL = 2k
CL = 60pF
1168 G35
G = 100
VS = ±15V
RL = 2k
CL = 60pF
20mV/DIV
5V/DIV
200µs/DIV
G = 1000
VS = ±15V
RL = 2k
CL = 60pF
1168 G37
200µs/DIV
G = 1000
VS = ±15V
RL = 2k
CL = 60pF
1168 G36
10µs/DIV
Negative Power Supply Rejection
Ratio vs Frequency
Small-Signal Transient Response
Large-Signal Transient Response
NEGATIVE POWR SUPPLY REJECTION RATIO (dB)
10µs/DIV
G = 10
VS = ±15V
RL = 2k
CL = 60pF
1168 G38
160
G = 1000
140
G = 100
120
G = 10
100
G=1
80
60
40
20
VS = ±15V
TA = 25°C
0
0.1
1
10
100
1k
FREQUENCY (Hz)
10k
100k
1168 G39
Common Mode Rejection Ratio vs
Frequency (1k Source Imbalance)
160
G = 100
120
G = 10
100
G=1
80
60
40
0
VS = ±15V
TA = 25°C
0.1
1
10k
100k
1168 G40
10
G = 100
G = 10
100
G=1
80
60
40
20
1
10
100
1k
FREQUENCY (Hz)
0.4
0.3
0.2
VS = ±15V
TA = 25°C
1k SOURCE IMBALANCE
0.1
VS = ±15V
0.5
120
0
10
100
1k
FREQUENCY (Hz)
G = 1000
140
SUPPLY CURRENT (mA)
G = 1000
140
20
Supply Current vs Temperature
0.6
160
COMMON MODE REJECTION RATIO (dB)
POSITIVE POWR SUPPLY REJECTION RATIO (dB)
Positive Power Supply Rejection
Ratio vs Frequency
10k
100k
1168 G41
0.1
–50 –25
50
25
0
75
TEMPERATURE (°C)
100
125
1168 G42
LT1168
W
BLOCK DIAGRA
+VS
VB
R5
30k
+
R6
30k
6 OUTPUT
A1
–
R3
400Ω
–IN
C1
2
Q1
R1
24.7k
–
–VS
+
A3
RG 1
RG 8
–VS
VB
+VS
+
R7
30k
R8
30k
5 REF
A2
–
R4
400Ω
+IN
3
C2
Q2
–VS
R2
24.7k
7 +VS
–VS
4 –VS
PREAMP STAGE
DIFFERENCE AMPLIFIER STAGE
1168 F01
Figure 1. Block Diagram
U
THEORY OF OPERATIO
The LT1168 is a modified version of the three op amp
instrumentation amplifier. Laser trimming and monolithic
construction allow tight matching and tracking of circuit
parameters over the specified temperature range. Refer to
the block diagram (Figure 1) to understand the following
circuit description. The collector currents in Q1 and Q2 are
trimmed to minimize offset voltage drift, thus assuring a
high level of performance. R1 and R2 are trimmed to an
absolute value of 24.7k to assure that the gain can be set
accurately (0.6% at G = 100) with only one external
resistor RG. The value of RG in parallel with R1 (R2)
determines the transconductance of the preamp stage. As
RG is reduced for larger programmed gains, the transconductance of the input preamp stage increases to that of the
input transistors Q1 and Q2. This increases the open-loop
gain when the programmed gain is increased, reducing
the input referred gain related errors and noise. The input
voltage noise at gains greater than 50 is determined only
by Q1 and Q2. At lower gains the noise of the difference
amplifier and preamp gain setting resistors increase the
noise. The gain bandwidth product is determined by C1,
C2 and the preamp transconductance which increases
with programmed gain. Therefore, the bandwidth does not
drop proportionally with gain.
The input transistors Q1 and Q2 offer excellent matching,
which is inherent in NPN bipolar transistors, as well as
picoampere input bias current due to superbeta processing. The collector currents in Q1 and Q2 are held constant
due to the feedback through the Q1-A1-R1 loop and
Q2-A2-R2 loop which in turn impresses the differential
input voltage across the external gain set resistor RG.
Since the current that flows through RG also flows through
R1 and R2, the ratios provide a gained-up differential
11
LT1168
U
THEORY OF OPERATIO
voltage, G = (R1 + R2)/RG, to the unity-gain difference
amplifier A3. The common mode voltage is removed by
A3, resulting in a single-ended output voltage referenced
to the voltage on the REF pin. The resulting gain equation
is:
G = (49.4kΩ / RG) + 1
solving for the gain set resistor gives:
Input Voltage Range
RG = 49.4kΩ /(G – 1)
Table 1 shows appropriate 1% resistor values for a variety
of gains.
Table 1
DESIRED GAIN
RG
CLOSEST 1% VALUE
RESULTANT GAIN
1
Open
Open
1
2
49400Ω
49900Ω
1.99
5
12350Ω
12400Ω
4.984
10
5488.89Ω
5490Ω
9.998
20
2600Ω
2610Ω
19.93
50
1008.16Ω
1000Ω
50.4
100
498.99Ω
499Ω
99.998
200
248.24Ω
249Ω
199.4
500
99Ω
100Ω
495
1000
49.95Ω
49.4Ω
1001
Input and Output Offset Voltage
The offset voltage of the LT1168 has two components: the
output offset and the input offset. The total offset voltage
referred to the input (RTI) is found by dividing the output
offset by the programmed gain (G) and adding it to the
input offset. At high gains the input offset voltage dominates, whereas at low gains the output offset voltage
dominates. The total offset voltage is:
Total input offset voltage (RTI)
= input offset + (output offset/G)
Total output offset voltage (RTO)
= (input offset • G) + output offset
Reference Terminal
The reference terminal is one end of one of the four 30k
resistors around the difference amplifier. The output
12
voltage of the LT1168 (Pin 6) is referenced to the voltage
on the reference terminal (Pin 5). Resistance in series
with the REF pin must be minimized for best common
mode rejection. For example, a 6Ω resistance from the
REF pin to ground will not only increase the gain error by
0.02% but will lower the CMRR to 80dB.
The input voltage range for the LT1168 is specified in the
data sheet at 1.4V below the positive supply to 1.9V
above the negative supply for a gain of one. As the gain
increases the input voltage range decreases. This is due
to the IR drop across the internal gain resistors R1 and
R2 in Figure 1. For the unity gain condition there is no IR
drop across the gain resistors R1 and R2, the output of
the GM amplifiers is just the differential input voltage at
Pin 2 and Pin 3 (level shifted by one VBE from Q1 and Q2).
When a gain resistor is connected across Pins 1 and 8,
the output swing of the GM cells is now the differential
input voltage (level shifted by VBE) plus the differential
voltage times the gain (ratio of the internal gain resistors
to the external gain resistor across Pins 1 and 8). To
calculate how close to the positive rail the input (VIN) can
swing for a gain of 2 and a maximum expected output
swing of 10V, use the following equation:
+ VS – VIN = – 0.5 – (VOUT/G) • (G – 1)/2
Substituting yields:
– 0.5 – (10/2) • (1/2) = – 3V
below the positive supply or 12V for a 15V supply. To
calculate how far above the negative supply the input can
swing for a gain of 10 with a maximum expected output
swing of –10V, the equation for the negative case is:
– VS + VIN = 1.5 – (VOUT/G) • (G – 1)/2
Substituting yields:
1.5 – (–10/10) • 9/2 = 6V
above the negative supply or – 9V for a negative supply
voltage of –15V. Figures 2 and 3 are for the positive
common mode and negative common mode cases
respectively.
LT1168
U
THEORY OF OPERATIO
INPUT VOLTAGE WITH RESPECT
TO POSITIVE SUPPLY (+VS – VIN)(V)
G=1
AREA OF OPERATION
–1
G=2
AREA OF
OPERATION
–2
–3
G = 100
AREA OF
OPERATION
–4
G = 10
AREA OF
OPERATION
–5
–6 T = 25°C
A
INPUT COMMON
–7 MODE RANGE IS
BELOW THE CURVE
–8
2
4
8
6
0
VOUT (V)
10
12
14
1168 F02
Figure 2. Positive Input Range vs
Output Voltage for Different Gains
G = 10
AREA OF
OPERATION
8
7
TA = 25°C
INPUT COMMON
MODE RANGE IS
ABOVE THE CURVE
Output Offset Trimming
The LT1168 is laser trimmed for low offset voltage so that
no external offset trimming is required for most applications. In the event that the offset needs to be adjusted, the
circuit in Figure 4 is an example of an optional offset adjust
circuit. The op amp buffer provides a low impedance to the
REF pin where resistance must be kept to minimum for
best CMRR and lowest gain error.
RG
G = 100
AREA OF
OPERATION
4
–VS
–14
+IN
G=1
AREA OF OPERATION
–12
–10
–8
–6
VOUT (V)
6
LT1168
3
OUTPUT
–4
–2
+VS
REF
8
G=2
3
AREA OF
OPERATION
2
1
–
1
6
5
2
–IN
+
5
10mV
1/2 LT1112
±10mV
ADJUSTMENT RANGE
100Ω
+
INPUT VOLTAGE RANGE WITH RESPECT
TO NEGATIVE SUPPLY (–VS + VIN)(V)
9
potential, the voltage on the REF pin can be further level
shifted. The application in the front of this data sheet,
Single Supply Pressure Monitor, is an example. An op amp
is used to buffer the voltage on the REF pin since a parasitic
series resistance will degrade the CMRR.
–
+VS
10k
100Ω
0
–10mV
1168 F03
Figure 3. Negative Input Voltage Range
vs Output Voltage for Various Gains
–VS
1168 F04
Figure 4. Optional Trimming of Output Offset Voltage
Single Supply Operation
For best results under single supply operation, the REF pin
should be raised above the negative supply (Pin 4) and one
of the inputs should be at least 2.5V above ground. The
barometer application later in this data sheet is an example
that satisfies these conditions. The resistance RSET from
the bridge transducer to ground sets the operating current
for the bridge, and with R6, also has the effect of raising the
input common mode voltage. The output of the LT1168 is
always inside the specified range since the barometric
pressure rarely goes low enough to cause the output to clip
(30.00 inches of Hg corresponds to 3.000V). For applications that require the output to swing at or below the REF
Input Bias Current Return Path
The low input bias current of the LT1168 (250pA) and the
high input impedance (200GΩ) allow the use of high
impedance sources without introducing additional offset
voltage errors, even when the full common mode range is
required. However, a path must be provided for the input
bias currents of both inputs when a purely differential
signal is being amplified. Without this path the inputs will
float to either rail and exceed the input common mode
range of the LT1168, resulting in a saturated input stage.
Figure 5 shows three examples of an input bias current
13
LT1168
U
THEORY OF OPERATIO
path. The first example is of a purely differential signal
source with a 10kΩ input current path to ground. Since the
impedance of the signal source is low, only one resistor is
needed. Two matching resistors are needed for higher
impedance signal sources as shown in the second
example. Balancing the input impedance improves both
common mode rejection and DC offset.
–
–
MICROPHONE,
HYDROPHONE,
ETC
LT1168
THERMOCOUPLE
–
LT1168
+
LT1168
+
200k
10k
+
200k
CENTER-TAP PROVIDES
BIAS CURRENT RETURN
1168 F05
Figure 5. Providing an Input Common Mode Current Path
U
W
U U
APPLICATIO S I FOR ATIO
The LT1168 is a low power precision instrumentation
amplifier that requires only one external resistor to accurately set the gain anywhere from 1 to 1000. The LT1168
is trimmed for critical DC parameters such as gain error
(0.04%, G = 10), input offset voltage (40µV, RTI), CMRR
(90dB min, G = 1) and PSRR (103dB min, G = 1). These
trims allow the amplifier to achieve very high DC accuracy.
The LT1168 achieves low input bias current of just 250pA
(max) through the use of superbeta processing. The
output can handle capacitive loads up to 1000pF in any
gain configuration and the inputs are protected against
ESD strikes up to ±13kV (human body).
Input Protection
The LT1168 can safely handle up to ±20mA of input
current in an overload condition. Adding an external 5k
input resistor in series with each input allows DC input
fault voltage up to ±100V and improves the ESD immunity
to ±8kV (contact) and ±15kV (air discharge), which is the
IEC 1000-4-2 level 4 specification. If lower value input
resistors must be used, a clamp diode from the positive
supply to each input will maintain the IEC 1000-4-2
14
specification to level 4 for both air and contact discharge.
A 2N4393 drain/source to gate is a good low leakage diode
for use with resistors between 1k and 20k, see Figure 6.
The input resistors should be carbon and not metal film or
carbon film in order to withstand the fault conditions.
J1
2N4393
J2
2N4393
RIN
OPTIONAL FOR
RIN < 20k
+
RG
RIN
+VS
LT1168
OUT
REF
–
–VS
1168 F06
Figure 6. Input Protection
RFI Reduction
In many industrial and data acquisition applications,
instrumentation amplifiers are used to accurately amplify
small signals in the presence of large common mode
LT1168
U
W
U U
APPLICATIO S I FOR ATIO
voltages or high levels of noise. Typically, the sources of
these very small signals (on the order of microvolts or
millivolts) are sensors that can be a significant distance
from the signal conditioning circuit. Although these sensors may be connected to signal conditioning circuitry,
using shielded or unshielded twisted-pair cabling, the cabling may act as antennae, conveying very high frequency
interference directly into the input stage of the LT1168.
The amplitude and frequency of the interference can have
an adverse effect on an instrumentation amplifier’s input
stage by causing an unwanted DC shift in the amplifier’s
input offset voltage. This well known effect is called RFI
rectification and is produced when out-of-band interference is coupled (inductively, capacitively or via radiation)
and rectified by the instrumentation amplifier’s input transistors. These transistors act as high frequency signal
detectors, in the same way diodes were used as RF
envelope detectors in early radio designs. Regardless of
the type of interference or the method by which it is
coupled into the circuit, an out-of-band error signal appears in series with the instrumentation amplifier’s inputs.
To significantly reduce the effect of these out-of-band
signals on the input offset voltage of instrumentation
amplifiers, simple lowpass filters can be used at the
inputs. This filter should be located very close to the input
pins of the circuit. An effective filter configuration is
illustrated in Figure 7, where three capacitors have been
added to the inputs of the LT1168. Capacitors CXCM1 and
CXCM2 form lowpass filters with the external series resistors RS1, 2 to any out-of-band signal appearing on each of
the input traces. Capacitor CXD forms a filter to reduce any
unwanted signal that would appear across the input traces.
An added benefit to using CXD is that the circuit’s AC
common mode rejection is not degraded due to common
mode capacitive imbalance. The differential mode and
common mode time constants associated with the capacitors are:
tDM(LPF) = (RS1 + RS2)(CXD + CXCM1 + CXCM2)
tCM(LPF) = (RS1|| RS2)(CXCM1+ CXCM2)
Setting the time constants requires a knowledge of the
frequency, or frequencies of the interference. Once this
frequency is known, the common mode time constants
can be set followed by the differential mode time constant.
To avoid any possibility of inadvertently affecting the
signal to be processed, set the common mode time
constant an order of magnitude (or more) smaller than the
differential mode time constant. Set the common mode
time constants such that they do not degrade the LT1168
inherent AC CMR. Then the differential mode time constant can be set for the bandwidth required for the application. Setting the differential mode time constant close to
the sensor’s BW also minimizes any noise pickup along
the leads. To avoid any possibility of common mode to
differential mode signal conversion, match the common
mode time constants to 1% or better. If the sensor is an
RTD or a resistive strain gauge and is in proximity to the
instrumentation amplifier, then the series resistors RS1, 2
can be omitted.
IN +
CXD
0.1µF
IN –
+VS
RS1 CXCM1
1.6k 0.001µF
RS2
1.6k
+
RG
LT1168
VOUT
–
CXCM2
0.001µF
–VS
f– 3dB ≈ 500Hz
1168 F07
EXTERNAL RFI
FILTER
Figure 7. Adding a Simple RC Filter at the Inputs to an
Instrumentation Amplifier is Effective in Reducing Rectification
of High Frequency Out-of-Band Signals
Nerve Impulse Amplifier
The LT1168’s low current noise makes it ideal for EMG
monitors that have high source impedances. Demonstrating the LT1168’s ability to amplify low level signals, the
circuit in Figure 8 takes advantage of the amplifier’s high
gain and low noise operation. This circuit amplifies the low
level nerve impulse signals received from a patient at
Pins␣ 2 and 3. RG and the parallel combination of R3 and R4
set a gain of ten. The potential on LT1112’s Pin 1 creates
15
LT1168
U
W
U U
APPLICATIO S I FOR ATIO
a ground for the common mode signal. C1 was chosen to
maintain the stability of the patient ground. The LT1168’s
high CMRR ensures that the desired differential signal is
amplified and unwanted common mode signals are attenuated. Since the DC portion of the signal is not important, R6 and C2 make up a 0.3Hz highpass filter. The AC
signal at LT1112’s Pin 5 is amplified by a gain of 101 set
by R7/R8 +1. The parallel combination of C3 and R7 form
a lowpass filter that decreases this gain at frequencies
above 1kHz. The ability to operate at ±3V on 350µA of
supply current makes the LT1168 ideal for battery-powered applications. Total supply current for this application
is 1.05mA. Proper safeguards, such as isolation, must be
added to this circuit to protect the patient from possible
harm.
3
8
+IN
R3
30k
R1
12k
R2
1M
R4
30k
–
1
PATIENT
GND
2
0.3Hz
HIGHPASS
7
+
3V
C2
0.47µF
RG
6k
6
LT1168
G = 10
1
2
1/2
LT1112
The LT1168’s low supply current, low supply voltage
operation and low input bias currents allow it to fit nicely
into battery-powered applications. Low overall power
dissipation necessitates using higher impedance bridges.
The single supply pressure monitor application on the
front of this data sheet, shows the LT1168 connected to
the differential output of a 3.5k bridge. The picoampere
input bias currents keep the error caused by offset current
to a negligible level. The LT1112 level shifts the LT1168’s
reference pin and the ADC’s analog ground pins above
ground. The LT1168’s and LT1112’s combined power
dissipation is still less than the bridge’s. This circuit’s total
supply current is just 2.2mA.
3V
PATIENT/CIRCUIT
PROTECTION/ISOLATION
C1
0.01µF
Low IB Favors High Impedance Bridges, Lowers
Dissipation
5
R6
1M
5
–
6
4
8
+
1/2
LT1112
–
4
–3V
–3V
OUTPUT
1V/mV
R7
10k
R8
100Ω
3
+
AV = 101
POLE AT 1kHz
–IN
7
C3
15nF
1168 F08
Figure 8. Nerve Impulse Amplifier
14
15V
3
+
12
7
THERMOMETRICS
DC95F103W
THERMO
METRICS
DC95G104Z
PRECISION
R
THERMISTOR T
LT1168
6
REF
1
2
–
49.4kΩ
VOUT = 1.25 •
RT
5
4
OUTPUT VOLTAGE (V)
8
10
8
6
4
YSI #44006
–15V
YSI #44011
1168 F09
LT1634-1.25
22k
–15V
2
0
–40 –20
0
20
40
60
80 100
120
TEMPERATURE (°C)
1168 F10
Figure 9. Precision Temperature Without Precision Resistors
16
Figure 10. Response of Figure 9 for Various Thermistors
LT1168
U
TYPICAL APPLICATIO S
Single Supply Barometer
VS
3
+
2
–
–
4
5k
4
R6
1k
5
6
R8
100k
2
1
–
7
R1
825Ω
5k
2
+
R2
12Ω
5k
+
RSET
R3
50k
1
5k
6
R4
50k
VS
3
6
LT1168
G = 60
8
3
5
TO
4-DIGIT
DVM
+
4
5
1/2
LT1490
–
7
R7
50k
0.6% ACCURACY AT 25°C
1.7% ACCURACY AT 0°C TO 60°C
VS = 8V TO 30V
VOLTS
2.800
3.000
3.200
INCHES Hg
28.00
30.00
32.00
1168 TA03
AC Coupled Instrumentation Amplifier
2
–IN
1
–
RG
+IN
6
LT1168
8
REF
3
5
+
6
OUTPUT
R1
1M
C1
0.1µF
2
+
1
1
1/2
LT1490
2
LT1634CCZ-1.25
LUCAS NOVA SENOR
NPC-1220-015-A-3L
8
–
R5
200k
3
LT1677
f –3dB =
1
(2π)(R1)(C1)
= 1.59Hz
1168 TA02
17
LT1168
U
TYPICAL APPLICATIO S
4-Digit Pressure Sensor
9V
R8
392k
3
+
2
1
1
1/4
LT1114
2
LT1634CCZ-1.25
LUCAS NOVA SENOR
NPC-1220-015A-3L
4
–
11
–
4
5k
R9
1k
2
9V
R1
825Ω
+
RSET
7
6
LT1168
G = 60
R2
12Ω
5k
6
–
1
5k
5k
2
1
8
5
3
3
+
4
10
+
9
0.6% ACCURACY AT ROOM TEMP
1.7% ACCURACY AT 0°C TO 60°C
VOLTS
2.800
3.000
3.200
18
INCHES Hg
28.00
30.00
32.00
13
R3
51k
+
–
14
1/4
LT1114
–
8
1/4
LT1114
5
12
TO
4-DIGIT
DVM
R4
100k
R5
100k
R6
50k
R7
180k
C1
1µF
1168 TA04
LT1168
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
N8 Package
8-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
0.400*
(10.160)
MAX
8
7
6
5
1
2
3
4
0.255 ± 0.015*
(6.477 ± 0.381)
0.300 – 0.325
(7.620 – 8.255)
0.065
(1.651)
TYP
0.009 – 0.015
(0.229 – 0.381)
(
+0.035
0.325 –0.015
8.255
+0.889
–0.381
0.130 ± 0.005
(3.302 ± 0.127)
0.045 – 0.065
(1.143 – 1.651)
)
0.125
(3.175) 0.020
MIN (0.508)
MIN
0.018 ± 0.003
(0.457 ± 0.076)
0.100
(2.54)
BSC
N8 1098
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
8
7
6
5
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
1
0.010 – 0.020
× 45°
(0.254 – 0.508)
0.008 – 0.010
(0.203 – 0.254)
0.053 – 0.069
(1.346 – 1.752)
0°– 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.014 – 0.019
(0.355 – 0.483)
TYP
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
2
3
4
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
BSC
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
SO8 1298
19
LT1168
U
TYPICAL APPLICATIO
Low Power Programmable Audio HPF/LPF with “Pop-Less” Switching
R3
8k
R2
4k
R1
4k
P1
3
14
P2
1
16
8
9
6
11
2
–
1/2 LT1462
VIN
3
+
4
–15V
2
15
12
13
4
5
7
10
+15V
7
6
LT1168
–
HPF
5
4
–15V
+
7
1/2 LT1462
6
NC +15V –15V
1
+
C1
100µF
5
LTC®201
+15V
8
GAIN SET
3
8
1
2
LPF
–
1168 TA05
P1
P2
—
0
POLE
100
0
1
1
1
0 < 0.8V
1 > 2.4V
200 400
TOTAL SUPPLY CURRENT < 400µA
Hz
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1043
Dual Precision Instrumentation Building Block
Switched Capacitor, Rail-to-Rail Input, 120dB CMRR
LTC1100
Precision Chopper-Stabilized Instrumentation Amplifier
G = 10 or 100, VOS = 10µV, IB = 50pA
LT1101
Precision, Micropower, Single Supply Instrumentation Amplifier
G = 10 or 100, IS = 105µA
LT1102
High Speed, JFET Instrumentation Amplifier
G = 10 or 100, Slew Rate = 30V/µs
LT1167
Single Resistor Programmable Precision Instrumentation Amplifier
Lower Noise than LT1168, eN = 7.5nV/√Hz
20
Linear Technology Corporation
1168f LT/TP 0800 4K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
 LINEAR TECHNOLOGY CORPORATION 2000
Similar pages