Magnetrol B75-1B20-KOE Non-bleed switch for liquid level switch Datasheet

Series K
Pneumatic Switch
Mechanism
Installation and Operating Manual
Non-Bleed
Switch For
Liquid Level
Switches
Read this Manual Before Installing
This manual provides information on the Series K
Pneumatic Switch Mechanism. It is important that all
instructions are read carefully and followed in sequence.
Detailed installation and hook-up instructions are included
in this manual.
Conventions Used in this Manual
Certain conventions are used in this manual to convey
specific types of information. General technical material,
support data, and safety information are presented in
narrative form. The following styles are used for notes,
cautions, and warnings.
Notes
Notes contain information that augments or clarifies an
operating step. Notes do not normally contain actions.
They follow the procedural steps to which they refer.
Cautions
Cautions alert the technician to special conditions that
could injure personnel, damage equipment, or reduce
a component’s mechanical integrity. Cautions are also
used to alert the technician to unsafe practices or the
need for special protective equipment or specific
materials. In this manual, a caution box indicates a
potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
Warnings
Warnings identify potentially dangerous situations or
serious hazards. In this manual, a warning indicates an
imminently hazardous situation which, if not avoided,
could result in serious injury or death.
Safety Messages
Follow all standard industry procedures for servicing electrical equipment when working with or around high
voltage. Always shut off the power supply before touching
any components.
Low Voltage Directive
For use in Installations Category II, Pollution Degree 2.
If equipment is used in a manner not specified by the
manufacturer, protection provided by equipment may
be impaired.
Notice of Copyright, and Limitations
Copyright © 2010 Magnetrol International, Incorporated.
All rights reserved.
Magnetrol reserves the right to make changes to the
product described in this manual at any time without
notice. Magnetrol makes no warranty with respect to the
accuracy of the information in this manual.
Warranty
All Magnetrol mechanical level and flow controls are warranted free of defects in materials or workmanship for five
full years from the date of original factory shipment.
If returned within the warranty period; and, upon factory
inspection of the control, the cause of the claim is
determined to be covered under the warranty; then,
Magnetrol will repair or replace the control at no cost to the
purchaser (or owner) other than transportation.
Magnetrol shall not be liable for misapplication, labor
claims, direct or consequential damage or expense arising
from the installation or use of equipment. There are no
other warranties expressed or implied, except special
written warranties covering some Magnetrol products.
Quality Assurance
The quality assurance system in place at Magnetrol guarantees the highest level of quality throughout the
company. Magnetrol is committed to providing full customer satisfaction both in quality products and quality
service.
Magnetrol’s quality assurance system is
registered to ISO 9001 affirming its
commitment to known international
quality standards providing the
strongest assurance of product/service
quality available.
42-686 Series K Pneumatic Switch Mechanism
1.0
Description
The Series K is a non-bleed pneumatic switch. It incorporates a three-way pneumatic valve assembly, actuated by a
magnet swing carriage. Mechanisms are available as an
option for most Magnetrol liquid level controls.
2.0
Technology
Magnetic force and the lever mechanism transmit movement from the pressure vessel to the pneumatic valve.
Figure 1 shows the position of the attraction sleeve and
magnet when the liquid level is such that the attraction
sleeve is below the field of the magnet. In this position, the
flapper has been drawn away from the valve rod, permitting
the inlet air or gas to flow to a pneumatic operator. Inlet air
pressure against the ball allows the ball to seal off the
exhaust outlet.
Figure 2 shows the position of the attraction sleeve and the
magnet when the liquid level has risen, causing the attraction sleeve to attract the magnet against the enclosing tube.
In this position, the flapper actuates the air valve, closing
the supply inlet and opening the exhaust port, which
reduces the pressure in the operator to atmospheric. This
action, “close” on high, is reversible to “open” on high with
two simple adjustments (refer to page 4).
NOTE: In order to protect the switch assembly from contaminants,
filtered and dried gas/air supply is recommended.
Pivot
Non-magnetic
enclosing tube
D
Non-magnetic
enclosing tube
Upper
shoulder
screw
R
R
Reverse link
position for
opposite action
Attraction sleeve
Flapper
adjustment screw
Air valve
Actuating link
Pivot
Lower shoulder
screw
Air supply
open position
Magnet (swing
out position)
To operator
Flapper
Exhaust
closed
Pivot
Falling
level
D
Attraction sleeve
Flapper
adjustment screw
Air valve
Upper
shoulder
screw
Reverse link
position for
opposite action
Actuating link
Pivot
Lower shoulder
screw
Magnet (swing
in position)
Air supply
closed position
To operator
Flapper
Exhaust
open
Rising
level
Figure 1
Figure 2
Attraction sleeve below field of magnet
Attraction sleeve in field of magnet
42-686 Series K Pneumatic Switch Mechanism
1
3.0
Reversing Pilot Action
Enclosing tube
All Series K Pneumatic Switch Mechanisms are shipped
from the factory in the direct (close) position at high level.
They can be field modified for the reverse (open) position
by following the steps below:
1. The action can be reversed by first removing the upper
shoulder screw from the actuator link and moving it from
the direct (D) position to the reverse (R); refer to Figure 3.
2. Loosen the screw that positions the spring bracket and
move it from the direct (D) position to the reverse (R) position; refer to Figure 4.
3. Fasten screw securely.
Reverse position
Direct position
Fall-out stop
Upper shoulder
screw
Magnet Tab
Frame screw
Actuator
link
Housing
base
The switch is now setup for reverse action.
Enclosing
tube nut
Locking screw
4.0
Figure 3
Locating Air Line Connection
Caution: Instrument is designed for dry air/gas service.
The housing base may be rotated a full 360° for your convenience in connecting the air supply.
1. Loosen both the special locking screw above the enclosing
tube nut and the frame screw. Refer to Figure 3.
2. Rotate the entire base to the desired position.
3. Tighten both the locking screw and the frame screw.
4.0.1 Remove complete mechanism
Enclosing tube
Direct
position
Fall-out spring
1. Disconnect air line from air line adapter.
2. Loosen both the special locking screw, above the enclosing
tube nut, and the frame screw approximately 3 to 4 turns.
Refer to Figure 3.
3. Lift the entire base straight up and off the enclosing tube.
Spring
bracket
1
⁄4" NPT Air line
inlet connection
Reverse
position
⁄4" NPT Outlet
connection
1
Figure 4
2
42-686 Series K Pneumatic Switch Mechanism
5.0
Preventive Maintenance
5.0.1 Nozzle cleaning
To clean the nozzle, follow the steps below:
1. Unscrew and remove the adapter. Refer to Figure 5.
Enclosing tube
Caution: Do not lose the ball which will drop out when the adapter
is removed.
Socket set
screw
1
⁄16" Allen
wrench
Air line
adapter
Ball
Nozzle
Actuating rod
Flapper
Figure 5
2. The ball and actuating rod will now fall out when the
switch is tipped.
3. Unscrew the socket set screw with a 1⁄16" Allen wrench. This
will prevent damage to the flapper when performing step 4.
4. Insert a 1⁄16" diameter wire into the nozzle from the air line
connection side. Refer to Figure 6. The wire may be moved
back and forth to clean the opening of any accumulated
matter.
5. Reassemble the actuating rod, ball, and adapter; insert into
nozzle. Refer to Figure 5.
6. Securely tighten the air line adapter.
7. Readjust the flapper to its original position; refer to Nozzle
Flapper Readjustment procedure.
5.0.2 Nozzle flapper readjustment
Magnet
(yellow
or red
dot)
Enclosing tube
Socket set screw
⁄16" Diameter wire
1
Flapper
Nozzle
Figure 6
42-686 Series K Pneumatic Switch Mechanism
1. Connect an air line to the adapter.
2. Pressurize the air line.
3. Adjust the flapper with the socket set screw for the desired
action:
Direct Action
A. Hold the magnet against the enclosing tube.
B. Adjust the socket set screw with a 1⁄16" Allen wrench until
the air flow stops, plus an extra one-eighth turn.
Reverse Action
A. Hold the magnet tab against the fall out stop. Refer to
Figure 3.
B. Adjust the socket set screw with a 1⁄16" Allen wrench until
the air flow stops.
4. Manually actuate the switch under pressure to assure its correct actuation. The unit is now ready for service.
5. Operate control at normal process conditions to verify
adjustments.
3
6.0
Replacement Parts
6.1
K Series pneumatic switch
Replacement parts for K Series Pneumatic Switch
Mechanisms are available as an assembly only. Switch mechanism consists of entire pneumatic assembly mounted in the
switch housing base. See figure 7 below. When ordering an
assembly, be certain to specify:
1. The model number of the level control in which the switch
was installed.
2. The serial number of the level control in which the switch
was installed. Refer to nameplate attached to control.
Caution: When ordering replacement switch mechanisms, be
certain to determine color dot on magnet. Never replace
a mechanism having a red dot magnet with one having
a yellow dot magnet, and vice versa.
4.66"
(118)
Switch Code
Magnet
Part Number
KOE
KOF
KOG
KOH
KPE
KPF
Yellow
Yellow
Red
Red
Yellow
Yellow
89-7501-023
89-7501-023
89-7501-024
89-7501-024
89-7501-025
89-7501-025
1/4"
NPT
1.63"
(41)
1.63"
(41)
5.46"
(139)
Figure 7
4
42-686 Series K Pneumatic Switch Mechanism
6.2
Switch housing replacement assembly
Standard carbon steel housing replacement assemblies are
designed for general purpose indoor use installations requiring protection against entrance of dust, water, lint
and fiber/oil. Refer to Figure 8.
4.00"
(102)
or
6.00"
(152)
Replacement Kit
Part Number
Description
Blue Cover
Standard
housing cover
Short 4" (102 mm)
Tall 6" (152 mm)
Cover assembly hardware
Includes assembly hardware kit 89-6508-001.
Figure 8
89-6509-003 89-6510-003 89-6508-001
Carbon steel housing assembly
7.0
“K” Switch Specifications
Supply Pressure:
Airline Connections:
Maximum Leakage Rate:
Maximum Airflow:
100 psi Max. supply pressure
40 psi Max. supply pressure
Maximum Process Temp.:
Housing Protection:
Housing Material:
Switch Mechanism Material:
8.0
40 psi Max. or 100 psi Max.
⁄ " NPT
0.5 SCFH
1
4
1.1 SCFM
0.7 SCFM
+400° F
General Purpose/NEMA 1/IP53
Rolled steel/Cast aluminum
Stainless steel
Switch Codes
SWITCH MECHANISM AND ENCLOSURE
Switch
Code
KOG
KOH
KOE
KOF
KPE
KPF
Maximum
Supply
PSIG
40
40
100
100
100
100
Bar
3
3
7
7
7
7
Magnet
Dot
Red
Red
Yellow
Yellow
Yellow
Yellow
For use with
E-tube
Attraction
Wall
Sleeve
Inches (mm)
.035
.9
Standard
.035
.9
Standard
.035
.9
Sheathed
or
.065
1.7
Standard
.065
1.7
Sheathed
.065
1.7
Sheathed
Cover
Height
Inches
4
6
4
6
4
6
(mm)
102
152
102
152
102
152
Maximum leakage rate is .5 SCFH at maximum supply pressure. Maximum
process temperature is +400° F (+209° C).
Example Model Number:
B
7
5
1
B
2
42-686 Series K Pneumatic Switch Mechanism
0
5
ASSURED QUALITY & SERVICE COST LESS
Service Policy
Return Material Procedure
Owners of Magnetrol may request the return of a control or
any part of a control for complete rebuilding or replacement. They will be rebuilt or replaced promptly. Controls
returned under our service policy must be returned by
Prepaid transportation. Magnetrol will repair or replace the
control at no cost to the purchaser (or owner) other than
transportation if:
So that we may efficiently process any materials that are
returned, it is essential that a “Return Material
Authorization” (RMA) number be obtained from the factory, prior to the material's return. This is available through
Magnetrol’s local representative or by contacting the factory. Please supply the following information:
1. Returned within the warranty period; and
2. The factory inspection finds the cause of the claim to be
covered under the warranty.
If the trouble is the result of conditions beyond our control;
or, is NOT covered by the warranty, there will be charges for
labor and the parts required to rebuild or replace the equipment.
In some cases it may be expedient to ship replacement parts;
or, in extreme cases a complete new control, to replace the
original equipment before it is returned. If this is desired,
notify the factory of both the model and serial numbers of
the control to be replaced. In such cases, credit for the materials returned will be determined on the basis of the
applicability of our warranty.
1.
2.
3.
4.
5.
Company Name
Description of Material
Serial Number
Reason for Return
Application
Any unit that was used in a process must be properly
cleaned in accordance with OSHA standards, before it is
returned to the factory.
A Material Safety Data Sheet (MSDS) must accompany
material that was used in any media.
All shipments returned to the factory must be by prepaid
transportation.
All replacements will be shipped F.O.B. factory.
No claims for misapplication, labor, direct or consequential
damage will be allowed.
5300 Belmont Road • Downers Grove, Illinois 60515-4499 • 630-969-4000 • Fax 630-969-9489 • www.magnetrol.com
145 Jardin Drive, Units 1 & 2 • Concord, Ontario Canada L4K 1X7 • 905-738-9600 • Fax 905-738-1306
Heikensstraat 6 • B 9240 Zele, Belgium • 052 45.11.11 • Fax 052 45.09.93
Regent Business Ctr., Jubilee Rd. • Burgess Hill, Sussex RH15 9TL U.K. • 01444-871313 • Fax 01444-871317
Copyright © 2010 Magnetrol International, Incorporated. All rights reserved. Printed in the USA.
BULLETIN: 42-686.10
EFFECTIVE: August 2010
SUPERSEDES: June 2002
Similar pages