Fairchild FMS6646 Six channel, sd/hd (1080p) video filter driver Datasheet

FMS6646
Six Channel, SD/HD (1080p) Video Filter Driver
Features
Description
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Three Selectable 8/75MHz (SD/HD 1080p) Filters
The FMS6646 Low Cost Video Filter (LCVF) is intended
to replace passive LC filters and drivers with a low-cost
integrated device. Six Butterworth filters provide
improved image quality compared to typical passive
solutions. The combination of low-power StandardDefinition (SD) and High-Definition (HD 1080p) filters
greatly simplifies DVD video output circuitry. Three
channels offer fixed SD filters, while the other three are
selectable between SD and HD filters.
ƒ
ƒ
Low-Power
Three Fixed 8MHz (SD) Filters
Transparent Input Clamping
Single Video Load Drive (2VPP, 150Ω, AV = 6dB)
AC- or DC-Coupled Inputs
AC- or DC-Coupled Outputs
DC-Coupled Outputs Eliminate AC-Coupling
Capacitors
The FMS6646 offers a fixed gain of 6dB.
The FMS6646 may be directly driven by a DC-coupled
DAC output or an AC-coupled signal. Internal diode
clamps and bias circuitry may be used if AC-coupled
inputs are required (see the Applications Information
section for details).
Robust Output ESD Protection: 9kV HBM
Applications
ƒ
ƒ
ƒ
ƒ
ƒ
The outputs can drive AC- or DC-coupled single (150Ω)
video loads. DC-coupling the outputs removes the need
for output coupling capacitors. The input DC levels are
offset approximately +280mV at the output.
Cable and Satellite Set-Top Boxes
DVD Players
HDTV
Personal Video Recorders (PVR)
Video On Demand (VOD)
Ordering Information
Part Number
Operating
Temperature Range
Gain Setting
FMS6646MTC20X
-40°C to +85°C
6dB
Eco Status
RoHS
Package
Packing
Method
TSSOP-20
2500 / Reel
For Fairchild’s definition of Eco Status, please visit: http://www.fairchildsemi.com/company/green/rohs_green.html
Figure 1. Block Diagram
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev. 1.0.1
www.fairchildsemi.com
FMS6646 — Six Channel, 6th-Order SD/HD 1080p Video Filter Driver
July 2009
SD IN1
1
20
SD OUT1
SD IN2
2
19
SD OUT2
SD IN3
3
18
SD OUT3
17
GND
FMS6646
20L TSSOP
N/C
4
VCC
5
16
GND
FcSEL
6
15
N/C
SD/HD IN1
7
14
SD/HD OUT1
SD/HD IN2
8
13
SD/HD OUT2
SD/HD IN3
9
12
SD/HD OUT3
N/C
10
11
N/C
Figure 2. Pin Configuration
Pin Definitions
Pin#
Name
Type
Description
1
SD IN1
Input
SD video input, channel 1
2
SD IN2
Input
SD video input, channel 2
3
SD IN3
Input
SD video input, channel 3
4
N/C
Input
No Connection
5
VCC
Input
+3.3V supply
6
FcSEL
Input
Selects filter corner frequency for pins 7, 8, and 9: “0” = SD, “1” = PS
7
SD/HD IN1
Input
Selectable SD or PS video input, channel 1
8
SD/HD IN2
Input
Selectable SD or PS video input, channel 2
9
SD/HD IN3
Input
Selectable SD or PS video input, channel 3
10
N/C
Input
No Connection
11
N/C
Input
No Connection
12
SD/HD OUT3
Output
Filtered SD or PS video output, channel 3
13
SD/HD OUT2
Output
Filtered SD or PS video output, channel 2
14
SD/HD OUT1
Output
Filtered SD or PS video output, channel 1
15
N/C
Input
No Connection
16
GND
Input
Must be tied to ground
Must be tied to ground
17
GND
Input
18
SD OUT3
Output
Filtered SD video output, channel 3
19
SD OUT2
Output
Filtered SD video output, channel 2
20
SD OUT1
Output
Filtered SD video output, channel 1
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
Pin Configuration
www.fairchildsemi.com
2
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device
reliability. The absolute maximum ratings are stress ratings only.
Symbol
Parameter
Min.
Max.
Unit
V
VCC
DC Supply Voltage
-0.3
6.0
VIO
Analog and Digital I/O
-0.3
VCC+0.3
V
IOUT
Output Current, Any One Channel, Do Not Exceed
50
mA
Reliability Information
Symbol
TJ
TSTG
Parameter
Min.
Typ.
Junction Temperature
Storage Temperature Range
-65
TL
Reflow Temperature
ΘJA
Thermal Resistance, JEDEC Standard Multi-Layer Test
Boards, Still Air
Max.
Unit
+150
°C
+150
°C
+260
°C
74
°C/W
Electrostatic Discharge Information
Symbol
ESD
Parameter
Max.
Human Body Model, JESD22-A114
9
Charged Device Model, JESD22-C101
2
Unit
kV
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to Absolute Maximum Ratings.
Symbol
Parameter
TA
Operating Temperature Range
VCC
Supply Voltage Range
Min.
Typ.
-40
3.135
3.30
Max.
Unit
+85
°C
5.25
V
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
Absolute Maximum Ratings
DC Electrical Characteristics
Unless otherwise noted, TA=25°C, VCC=3.3V, RSOURCE=37.5Ω, inputs AC coupled with 0.1µF, all outputs AC coupled
with 220µF into 150Ω loads, referenced to 400kHz.
Symbol
Parameter
(1)
ICC
Supply Current
VIN
Video Input Voltage Range
VIL
Digital Input Low
VIH
(1)
Digital Input High
(1)
Conditions
Min.
Typ.
Max.
Units
No Load
80
95
mA
Referenced to GND if DC
Coupled
1.4
VPP
FcSEL
0
0.8
V
FcSEL
2.4
VCC
V
Note:
1. 100% tested at 25°C.
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
www.fairchildsemi.com
3
Unless otherwise noted, TA=25°C, VIN=1VPP, VCC=3.3V, RSOURCE=37.5Ω, all inputs AC coupled with 0.1µF, all outputs
AC coupled with 220µF into 150Ω loads, referenced to 400kHz.
Symbol
Parameter
Conditions
AVSD
Channel Gain
(2)
All SD Channels
f01dBSD
-0.1dB Flatness
All SD Channels
f1dBSD
(2)
fcSD
fSBSD
-1dB Flatness
-3dB Bandwidth
(2)
Attenuation (Stopband Reject)
(2)
Min.
Typ.
Max.
Units
5.8
6.0
6.2
dB
5.5
MHz
All SD Channels
5.5
7.15
MHz
All SD Channels
6.5
8.0
MHz
All SD Channels at f=27MHz
50
60
dB
DG
Differential Gain
All SD Channels
0.5
%
DP
Differential Phase
All SD Channels
0.3
°
Total Harmonic Distortion, Output
VOUT=1.4VPP, 3.58MHz
0.25
%
Crosstalk (ch-to-ch)
1MHz
-70
dB
NTC-7 weighting, 100kHz to
4.2MHz
72
dB
THD
XTALKSD
(3)
SNR
Signal-to-Noise Ratio
tpdSD
Propagation Delay
Delay from input to output,
4.5MHz
90
ns
CLGSD
Chroma Luma Gain
f=3.58MHz
(refer to SDIN at 400kHz)
100
%
CLDSD
Chroma Luma Delay
f=3.58MHz
(refer to SDIN at 400kHz)
6
ns
Notes:
2. 100% tested at 25°C.
3. SNR=20 • log (714mV / rms noise).
High-Definition (1080p) Electrical Characteristics
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
Standard-Definition (480i) Electrical Characteristics
Unless otherwise noted, TA=25°C, VIN=1VPP, VCC=3.3V, RSOURCE=37.5Ω, all inputs AC coupled with 0.1µF, all outputs
AC coupled with 220µF into 150Ω loads, referenced to 400kHz.
Symbol
Parameter
AVHD
Channel Gain
f1dBHD
-1dB Bandwidth
(4)
fcHD
-3dB Bandwidth
(4)
fsbHD
THD
XTALKHD
Conditions
(4)
Attenuation Stopband Reject
(4)
Min.
Typ.
Max.
Units
All HD Channels
5.8
6.0
6.2
All HD Channels
55
65
MHz
All HD Channels
70
75
MHz
All HD Channels, f=148MHz
15
dB
20
dB
Total Harmonic Distortion, Output
All HD Channels,
VOUT=1.4VPP, 22MHz
0.2
%
Crosstalk (ch-to-ch)
1MHz
-72
dB
Unweighted; 100kHz to
70MHz
70
dB
Delay from input to output
6
ns
SNR
Signal-to-Noise Ratio
tpdHD
Propagation Delay
(5)
Notes:
4. 100% tested at 25°C.
5. SNR=20 • log (714mV / rms noise).
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
www.fairchildsemi.com
4
Figure 3.
FMS6646 SD Frequency Response
0.5
0.0
Attenuation (dB)
-0.5
-1.0
-1.5
-2.0
-2.5
-3.0
-3.5
8.
1
7.
7
7.
3
6.
9
6.
5
6.
1
5.
7
5.
3
4.
9
4.
5
4.
1
3.
7
3.
3
2.
9
2.
5
2.
1
1.
7
1.
3
0.
9
0.
5
0.
1
-4.0
Frequency (MHz)
Figure 4.
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
Typical Performance Characteristics
FMS6646 SD Frequency Response (Flatness)
5
Attenuation (dB)
0
-5
-10
-15
-20
-25
8.
2
16
.3
24
.4
32
.5
40
.6
48
.7
56
.8
64
.9
73
.0
81
.1
89
.2
97
.2
10
5.
3
11
3.
4
12
1.
5
12
9.
6
13
7.
7
14
5.
8
15
3.
9
16
2.
0
17
0.
1
17
8.
2
0.
1
-30
Frequency (MHz)
Figure 5.
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
FMS6646 HD Frequency Response
www.fairchildsemi.com
5
Figure 6.
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
FMS6646 HD Frequency Response (Flatness)
Figure 7.
Differential Gain
Figure 8.
Differential Phase
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
Typical Performance Characteristics (Continued)
www.fairchildsemi.com
6
DVD Player or STB
+5V
0.1
µF
Y1 OUT
1
10.0
µF
SD OUT1
SD IN1
20
C OUT
SD OUT2
SD IN2
75 Ω
220µF
75 Ω
220µF
Y1
75 Ω Video Cable s
19
C
75 Ω
3
SD OUT3
SD IN3
18
CV
75 Ω
4
16, 17
GND
N/C
Video
SoC
220µF
75 Ω
2
CV OUT
75 Ω
5
Vcc
G/Y2 OUT
B/Pb OUT
R/Pr OUT
7
14
SD/HD IN1
75 Ω
75 Ω Video Cable s
Y2/G
75 Ω
8
13
SD/HD IN2
75 Ω
220µF
75 Ω
220µF
Pb/B
SD/HD OUT2
75 Ω
9 SD/HD IN3
N/C
SD/HD OUT3 12
F
cSEL
AC-coupling caps
are optional
DAC load resistors
Pr/R
75 Ω
6
15
Figure 9. Typical Application
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
220µF
SD/HD OUT1
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
Typical Application
www.fairchildsemi.com
7
Functional Description
The FMS6646 Low-Cost Video Filter (LCVF) provides
6dB gain from input to output. In addition, the input is
slightly offset to optimize the output driver performance.
The offset is held to the minimum required value to
decrease the standing DC current into the load. Typical
voltage levels are shown in Figure 10.
0.65V
YIN
Driver
YOUT
1.0 -> 1.02V
800k
0.65 -> 0.67V
Figure 11. Input Clamp Circuit
0.3 -> 0.32V
0.0 -> 0.02V
V IN
For DC-coupled DAC drive with DC-coupled outputs,
use the configuration shown in Figure 12.
2.28V
1.58V
0.88V
0.28V
I/O Configurations
V OUT
Driven by:
DC-Coupled DAC Outputs
AC-Coupled and Clamped
Y, CV, R, G, B
0V - 1.4V
DVD or
STB
SoC
DAC
Output
There is a 280mV offset from the DC input level to the
DC output level. VOUT = 2 • VIN + 280mV.
LCVF
Clamp
Inactive
75Ω
0.85V
Figure 12. DC-Coupled Inputs and Outputs
0.5V
If the DAC’s average DC output level causes the signal
to exceed the range of 0V to 1.4V, it can be AC-coupled
as shown in Figure 13.
0.15V
V IN
1.98V
0V - 1.4V
DVD or
STB
SoC
DAC
Output
Driven by:
AC-Coupled and Biased
U, V, Pb, Pr, C
1.28V
0.58V
V OUT
0.1μF
LCVF
Clamp
Active
75Ω
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
Applications Information
Figure 10. Typical Voltage Levels
Figure 13. AC-Coupled Inputs, DC-Coupled Outputs
The FMS6646 provides an internal diode clamp to
support AC-coupled input signals. If the input signal
does not go below ground, the input clamp does not
operate. This allows DAC out puts to directly drive the
FMS6646 without an AC coupling capacitor. The worstcase sync tip compression due to the clamp does not
exceed 7mV. The input level set by the clamp,
combined with the internal DC offset, keeps the output
within its acceptable range. When the input is ACcoupled, the diode clamp sets the sync tip (or lowest
voltage) just below ground.
When the FMS6646 is driven by an unknown external
source or a SCART switch with its own clamping
circuitry, the inputs should be AC-coupled as shown in
Figure 14.
0V - 1.4V
External video
source must
be AC coupled
LCVF
Clamp
Active
75Ω
75Ω
For symmetric signals like C, U, V, Cb, Cr, Pb, and Pr;
the average DC bias is fairly constant and the inputs
can be AC-coupled with the addition of a pull-up resistor
to set the DC input voltage. DAC outputs can also drive
these same signals without the AC coupling capacitor.
A conceptual illustration of the input clamp circuit is
shown in Figure 11.
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
0.1μF
Figure 14. SCART Configuration with DC-Coupled
Outputs
www.fairchildsemi.com
8
Power Dissipation
The FMS6646 output drive configuration must be
considered when calculating overall power dissipation.
Care must be taken not to exceed the maximum die
junction temperature. The following example can be
used to calculate the FMS6646’s power dissipation and
internal temperature rise:
TJ = TA + Pd • θJA
External video
source must
be AC coupled
75Ω
0.1μF
where Pd = PCH1 + PCH2 + PCHx and
7.5MΩ
LCVF
Bias
Input
2
PCHx = VS • ICH - (VO /RL)
75Ω
where VO = 2VIN + 0.280V
ICH = (ICC / 6) + (VO/RL)
500mV +/-350mV
VIN = RMS value of input signal
ICC = 90mA , VS = 3.3V
RL = channel load resistance
Figure 15. Biased SCART with DC-Coupled Outputs
The same circuits can be used with AC-coupled outputs
if desired, as shown in Figure 16.
0V - 1.4V
DVD or
STB
SoC
DAC
Output
LCVF
Clamp
Inactive
Board layout can affect thermal characteristics. Refer to
the Layout Considerations section for more information.
Output Considerations
220µF
75
The FMS6646 outputs will be DC offset from the input
by 150mv therefore VOUT = 2*VIN DC+150mv. This offset
is required to obtain optimal performance from the
output driver and is held at the minimum value in order
to decrease the standing DC current into the load.
Since the FMS6646 has a 2x (6dB) gain, the output is
typically connected via a 75Ω series back-matching
resistor followed by the 75Ω video cable. Because of
the inherent divide by two of this configuration, the
blanking level at the load of the video signal is always
less then 1V. When AC-coupling the output ensure that
the coupling capacitor of choice will pass the lowest
frequency content in the video signal and that line time
distortion (video tilt) is kept as low as possible.
Figure 16. DC-Coupled Inputs, AC-Coupled Outputs
0V - 1.4V
0.1μF
DVD or
STB
SoC
DAC
Output
LCVF
Clamp
Active
75Ω
220μF
The selection of the coupling capacitor is a function of
the subsequent circuit input impedance and the leakage
current of the input being driven. In order to obtain the
highest quality output video signal the series
termination resistor must be placed as close to the
device output pin as possible. This greatly reduces the
parasitic capacitance and inductance effect on the
FMS6646 output driver. Recommend distance from
device pin to place series termination resistor should be
no greater than 0.1 inches.
Figure 17. -Coupled Inputs, AC-Coupled Outputs
External video
source must
be AC coupled.
75W
7.5MW
0.1µF
LCVF
Clamp
Active
75W
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
The same method can be used for biased signals with
the addition of a pull-up resistor to make sure the clamp
never operates. The internal pull-down resistance is
800kΩ±20%, so the external resistance should be
7.5MΩ to set the DC level to 500mV. If a pull-up
resistance less than 7.5MΩ is desired, an external pulldown can be added such that the DC input level is set
to 500mV.
220µF
500mV +/-350mV
Figure 18. Biased SCART with AC-Coupled Outputs
Note:
6. The video tilt or line time distortion is dominated by
the AC-coupling capacitor. The value may need to
be increased beyond 220μF to obtain satisfactory
operation in some applications.
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
Figure 19. Distance from Device Pin to Series
Termination Resistor
www.fairchildsemi.com
9
The FMS6646DEMO is a four-layer board with a full
power and ground plane. Following this layout
configura-tion pro vides the optimum performance
and thermal char-acteristics. For best results, follow
the steps below as a basis for high-frequency layout:
General layout and supply bypassing play major roles
in high-frequency performance and thermal
characteristics. Fairchild offers a demonstration
board, FMS6646DEMO, to guide layout and aid
device testing and characteriza-tion.
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Include 0.01μF and 0.1μF ceramic bypass capacitors.
Place the 0.01μF capacitor within 0.75 inches of the power pin.
Place the 0.1μF capacitor within 0.1 inches of the power pin.
For multi-layer boards, use a large ground plane to help dissipate heat.
For two-layer boards, use a ground plane that extends beyond the device by at least 0.5 inches.
Minimize all trace lengths to reduce series inductances.
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
Layout Considerations
www.fairchildsemi.com
10
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
Physical Dimensions
Figure 20.
20-Lead Thin Shrink Small Outline Package (TSSOP)
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner
without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify
or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically
the warranty therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/.
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
www.fairchildsemi.com
11
FMS6646 — Low-Cost, Six-Channel Video Filter Driver for SD/HD 1080p
© 2009 Fairchild Semiconductor Corporation
FMS6646 • Rev.1.0.1
www.fairchildsemi.com
12
Similar pages