ON N02L6181AB8IT 2mb ultra-low power asynchronous cmos sram 128kx16 bit Datasheet

N02L6181A
2Mb Ultra-Low Power Asynchronous CMOS SRAM
128Kx16 bit
Features
Overview
• Single Wide Power Supply Range
1.65 to 2.2 Volts
The N02L6181A is an integrated memory device
containing a 2 Mbit Static Random Access Memory
organized as 131,072 words by 16 bits. The device
is designed and fabricated using ON
Semiconductor’s advanced CMOS technology to
provide both high-speed performance and ultra-low
power. The base design is the same as ON
Semiconductor’s N02L63W3A, which is processed
to operate at higher voltages. The device operates
with a single chip enable (CE) control and output
enable (OE) to allow for easy memory expansion.
Byte controls (UB and LB) allow the upper and
lower bytes to be accessed independently. The
N02L6181A is optimal for various applications
where low-power is critical such as battery backup
and hand-held devices. The device can operate
over a very wide temperature range of -40oC to
+85oC and is available in JEDEC standard
packages compatible with other standard 128Kb x
16 SRAMs.
• Very low standby current
0.5µA at 1.8V (Typical)
• Very low operating current
1.4mA at 1.8V and 1µs (Typical)
• Very low Page Mode operating current
0.5mA at 1.8V and 1µs (Typical)
• Simple memory control
Single Chip Enable (CE)
Byte control for independent byte operation
Output Enable (OE) for memory expansion
• Low voltage data retention
Vcc = 1.2V
• Very fast output enable access time
30ns OE access time
• Automatic power down to standby mode
• TTL compatible three-state output driver
• Compact space saving BGA package
Product Family
Part Number
Package Type
N02L6181AB
48 - BGA
N02L6181AB2
Green 48-BGA
©2008 SCILLC. All rights reserved.
July 2008 - Rev. 4
Operating
Temperature
Power
Supply
(Vcc)
-40oC to +85oC 1.65V - 2.2V
Speed
70 and 85ns
@ 1.65V
Standby
Operating
Current (ISB), Current (Icc),
Max
Max
10 µA
3 mA @ 1MHz
Publication Order Number:
N02L6181A/D
N02L6181A
Pin Configurations
1
2
3
4
5
6
A
LB
OE
A0
A1
A2
NC
B
I/O8
UB
A3
A4
CE
I/O0
C
I/O9
I/O10
A5
A6
I/O1
I/O2
D
VSS
I/O11
NC
A7
I/O3
VCC
E
VCC
I/O12
NC
A16
I/O4
VSS
F
I/O14 I/O13
A14
A15
I/O5
I/O6
G
I/O15
NC
A12
A13
WE
I/O7
H
NC
A8
A9
A10
A11
NC
48 Pin BGA (top)
6 x 8 mm
Pin Descriptions
Pin Name
Pin Function
A0-A16
Address Inputs
WE
CE
OE
LB
UB
I/O0-I/O15
Write Enable Input
Chip Enable Input
Output Enable Input
Lower Byte Enable Input
Upper Byte Enable Input
NC
VCC
Not Connected
VSS
Ground
Data Inputs/Outputs
Power
Rev. 4 | Page 2 of 11 | www.onsemi.com
N02L6181A
Functional Block Diagram
Address
Inputs
A0 - A3
Page
Address
Word Mux
Address
Inputs
A4 - A16
Word
Address
Decode
Logic
8K Page
x 16 word
x 16 bit
RAM Array
Decode
Logic
Input/
Output
Mux
and
Buffers
I/O0 - I/O7
I/O8 - I/O15
CE
WE
OE
UB
LB
Control
Logic
Functional Description
CE
WE
OE
UB
LB
I/O0 - I/O151
MODE
POWER
H
X
X
X
X
High Z
Standby2
Standby
L
X
X
H
H
High Z
Standby2
Standby
L
3
1
1
Active
L
L
L
H
H
X
L
L
Data In
Write3
L
L1
L1
Data Out
Read
Active
H
L1
L1
High Z
Active
Active
1. When UB and LB are in select mode (low), I/O0 - I/O15 are affected as shown. When LB only is in the select mode only I/O0 - I/O7
are affected as shown. When UB is in the select mode only I/O8 - I/O15 are affected as shown.
2. When the device is in standby mode, control inputs (WE, OE, UB, and LB), address inputs and data input/outputs are internally
isolated from any external influence and disabled from exerting any influence externally.
3. When WE is invoked, the OE input is internally disabled and has no effect on the circuit.
Capacitance1
Item
Symbol
Test Condition
Input Capacitance
CIN
VIN = 0V, f = 1 MHz, TA = 25oC
I/O Capacitance
CI/O
Min
o
VIN = 0V, f = 1 MHz, TA = 25 C
1. These parameters are verified in device characterization and are not 100% tested
Rev. 4 | Page 3 of 11 | www.onsemi.com
Max
Unit
8
pF
8
pF
N02L6181A
Absolute Maximum Ratings1
Item
Symbol
Rating
Unit
Voltage on any pin relative to VSS
VIN,OUT
–0.3 to VCC+0.3
V
Voltage on VCC Supply Relative to VSS
VCC
–0.3 to 3.0
V
Power Dissipation
PD
500
mW
Storage Temperature
TSTG
–40 to 125
oC
Operating Temperature
TA
-40 to +85
o
Soldering Temperature and Time
TSOLDER
240oC, 10sec(Lead only)
o
C
C
1. Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operating section of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Operating Characteristics (Over Specified Temperature Range)
Min.
Typ1
Max
Unit
1.65
1.8
2.2
V
1.2
2.2
V
VIH
0.7Vcc
VCC+0.3
V
Input Low Voltage
VIL
–0.3
0.3Vcc
V
Output High Voltage
VOH
IOH = 0.2mA
Output Low Voltage
VOL
IOL = -0.2mA
0.3
V
Input Leakage Current
ILI
VIN = 0 to VCC
0.5
µA
Output Leakage Current
ILO
OE = VIH or Chip Disabled
0.5
µA
Read/Write Operating Supply Current
@ 1 µs Cycle Time2
ICC1
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
1.4
3.0
mA
Read/Write Operating Supply Current
@ 70 ns Cycle Time2
ICC2
VCC=2.2 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
8.0
17.0
mA
Page Mode Operating Supply Current
@ 70ns Cycle Time2 (Refer to Power
Savings with Page Mode Operation
diagram)
ICC3
VCC=2.2V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
2.0
4.0
mA
Read/Write Quiescent Operating Supply Current3
ICC4
VCC=2.2V, VIN=VIH or VIL
Chip Enabled, IOUT = 0,
f=0
0.1
mA
ISB1
VIN = VCC or 0V
Chip Disabled
tA= 85oC, VCC = 2.2 V
10.0
µA
5.0
µA
Item
Symbol
Supply Voltage
VCC
Data Retention Voltage
VDR
Input High Voltage
Maximum Standby
Current3
Maximum Data Retention Current3
IDR
Test Conditions
Chip Disabled2
VCC = 1.2V, VIN = VCC or 0
Chip Disabled, tA= 85oC
VCC–0.2
V
0.5
1. Typical values are measured at Vcc=Vcc Typ., TA=25°C and are not 100% tested.
2. This parameter is specified with the outputs disabled to avoid external loading effects. The user must add current required to drive
output capacitance expected in the actual system.
3. This device assumes a standby mode if the chip is disabled (CE high). In order to achieve low standby current all inputs must be
within 0.2 volts of either VCC or VSS
Rev. 4 | Page 4 of 11 | www.onsemi.com
N02L6181A
Power Savings with Page Mode Operation (WE = VIH)
Page Address (A4 - A16 )
Word Address (A0 - A3)
Open page
Word 1
Word 2
...
Word 16
CE
OE
LB, UB
Note: Page mode operation is a method of addressing the SRAM to save operating current. The internal
organization of the SRAM is optimized to allow this unique operating mode to be used as a valuable power
saving feature.
The only thing that needs to be done is to address the SRAM in a manner that the internal page is left open
and 16-bit words of data are read from the open page. By treating addresses A0-A3 as the least significant
bits and addressing the 16 words within the open page, power is reduced to the page mode value which is
considerably lower than standard operating currents for low power SRAMs.
Rev. 4 | Page 5 of 11 | www.onsemi.com
N02L6181A
Timing Test Conditions
Item
Input Pulse Level
0.1VCC to 0.9 VCC
Input Rise and Fall Time
5ns
Input and Output Timing Reference Levels
0.5 VCC
Output Load
CL = 30pF
Power Supply Voltage
1.65 - 2.2V
Operating Temperature
-40 to +85 oC
Timing
85ns
70ns
Item
Symbol
Read Cycle Time
tRC
Address Access Time
tAA
85
70
ns
Chip Enable to Valid Output
tCO
85
70
ns
Output Enable to Valid Output
tOE
30
25
ns
Byte Select to Valid Output
tLB, tUB
85
70
ns
Chip Enable to Low-Z output
tLZ
10
10
ns
Output Enable to Low-Z Output
tOLZ
5
5
ns
Byte Select to Low-Z Output
tLBZ, tUBZ
10
10
ns
Chip Disable to High-Z Output
tHZ
30
25
ns
Output Disable to High-Z Output
tOHZ
30
25
ns
Byte Select Disable to High-Z Output
tLBHZ, tUBHZ
25
ns
Output Hold from Address Change
tOH
5
5
ns
Write Cycle Time
tWC
85
70
ns
Chip Enable to End of Write
tCW
50
40
ns
Address Valid to End of Write
tAW
50
40
ns
Byte Select to End of Write
tLBW, tUBW
50
40
ns
Write Pulse Width
tWP
50
40
ns
Address Setup Time
tAS
0
0
ns
Write Recovery Time
tWR
0
0
ns
Write to High-Z Output
tWHZ
Data to Write Time Overlap
tDW
40
40
ns
Data Hold from Write Time
tDH
0
0
ns
End Write to Low-Z Output
tOW
10
10
ns
Min.
Max.
85
Min.
70
30
25
Rev. 4 | Page 6 of 11 | www.onsemi.com
Max.
Units
ns
20
ns
N02L6181A
Timing of Read Cycle (CE = OE = VIL, WE = VIH)
tRC
Address
tAA
tOH
Data Out
Previous Data Valid
Data Valid
Timing Waveform of Read Cycle (WE= VIH)
tRC
Address
tAA
tHZ
tCO
CE
tLZ
tOHZ
tOE
OE
tOLZ
tLB, tUB
LB, UB
tLBLZ, tUBLZ
Data Out
High-Z
tLBHZ, tUBHZ
Data Valid
Rev. 4 | Page 7 of 11 | www.onsemi.com
N02L6181A
Timing Waveform of Write Cycle (WE control)
tWC
Address
tWR
tAW
tCW
CE
tLBW, tUBW
LB, UB
tWP
tAS
WE
tDW
High-Z
tDH
Data Valid
Data In
tWHZ
tOW
High-Z
Data Out
Timing Waveform of Write Cycle (CE Control)
tWC
Address
tAW
tWR
tCW
CE
tAS
tLBW, tUBW
LB, UB
tWP
WE
tDW
Data Valid
Data In
tLZ
Data Out
tDH
tWHZ
High-Z
Rev. 4 | Page 8 of 11 | www.onsemi.com
N02L6181A
44-Lead TSOP II Package (T44)
18.41±0.13
11.76±0.20
10.16±0.13
0.80mm REF
0.45
0.30
DETAIL B
SEE DETAIL B
1.10±0.15
0o-8o
0.20
0.00
0.80mm REF
Note:
1. All dimensions in inches (Millimeters)
2. Package dimensions exclude molding flash
Rev. 4 | Page 9 of 11 | www.onsemi.com
N02L6181A
Ball Grid Array Package
0.28±0.05
1.24±0.10
D
A1 BALL PAD
CORNER (3)
1. 0.35±0.05 DIA.
E
2. SEATING PLANE - Z
0.15 Z
0.05
TOP VIEW
SIDE VIEW
1. DIMENSION IS MEASURED AT THE
A1 BALL PAD
MAXIMUM SOLDER BALL DIAMETER.
CORNER
PARALLEL TO PRIMARY Z.
SD
e
SE
2. PRIMARY DATUM Z AND SEATING
PLANE ARE DEFINED BY THE
SPHERICAL CROWNS OF THE
SOLDER BALLS.
3. A1 BALL PAD CORNER I.D. TO BE
MARKED BY INK.
K TYP
J TYP
e
BOTTOM VIEW
Dimensions (mm)
e = 0.75
D
6±0.10
SD
SE
J
K
BALL
MATRIX
TYPE
0.375
0.375
1.125
1.375
FULL
E
8±0.10
Rev. 4 | Page 10 of 11 | www.onsemi.com
Z
N02L6181A
Ordering Information
Part Number
Package
Shipping Method
Speed
N02L6181AB7I
Leaded 48-BGA
Tray
70ns
N02L6181AB27I
Green 48-BGA (RoHS Compliant)
Tray
70ns
N02L6181AB8I
Leaded 48-BGA
Tray
85ns
N02L6181AB28I
Green 48-BGA (RoHS Compliant)
Tray
85ns
N02L6181AB7IT
Leaded 48-BGA
Tape & Reel
70ns
N02L6181AB27IT
Green 48-BGA (RoHS Compliant)
Tape & Reel
70ns
N02L6181AB8IT
Leaded 48-BGA
Tape & Reel
85ns
N02L6181AB28IT
Green 48-BGA (RoHS Compliant)
Tape & Reel
85ns
Revision History
Revision #
Date
A
Apr. 2003
Initial Release
Nov. 2005
Added TSOP II Green Pkg. , Green Pkg. Part # and RoHS Compliant
B
C
4
Change Description
September 2006 Converted to AMI Semiconductor
July 2008
Converted to ON Semiconductor and new part numbers
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without
further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does
SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special,
consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as
components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure
of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs,
damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative
Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
PO Box 5163, Denver, Colorado 80217 USA
Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada
Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800-282-9855 Toll
Free USA/Canada
Europe, Middle East & Africa Technical Support: Phone
421-33-790-2910
Japan Customer Focus Center:
Phone 81-3-5773-3850
Rev. 4 | Page 11 of 11 | www.onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
Similar pages