Intersil ICL3310ECB /- 15kv esd protected, 3v to 5.5v, 1 microamp, 250kbps, rs-232 transmitter/receiver Datasheet

CT
RODU
P
U CT
E
T
E
L
PROD
E
T
OBSO
U
IT
UBST
IBLE S ICL3222E
POSSSheet
Data
®
+/- 15kV ESD Protected, +3V to +5.5V,
1 Microamp, 250kbps, RS-232
Transmitter/Receiver
Table 1 summarizes the features of the ICL3310E, while
Application Note AN9863 summarizes the features of each
device comprising the ICL32XX 3V family.
Part # Information
PKG.
DWG. #
PACKAGE
FN6000.3
• ESD Protection for RS-232 I/O Pins to ±15kV (IEC61000)
The single pin powerdown function (SHDN = 0) disables all
the transmitters and receivers, while shutting down the
charge pump to minimize supply current drain.
TEMP.
RANGE (°C)
July 2004
Features
The Intersil ICL3310E contains 3.0V to 5.5V powered
RS-232 transmitters/receivers which meet ElA/TIA-232 and
V.28/V.24 specifications, even at VCC = 3.0V. Targeted
applications are PDAs, Palmtops, and notebook and laptop
computers where the low operational, and even lower
standby, power consumption is critical. Efficient on-chip
charge pumps, coupled with a manual powerdown function
reduces the standby supply current to a 1µA trickle. Small
footprint packaging, and the use of small, low value
capacitors ensure board space savings as well. Data rates
greater than 250kbps are guaranteed at worst case load
conditions. This device is fully compatible with 3.3V only
systems, mixed 3.3V and 5.0V systems, and 5.0V only
systems.
PART NO.
ICL3310E
ICL3310ECB
0 to 70
18 Ld SOIC
M18.3
ICL3310ECB-T
0 to 70
Tape and Reel
M18.3
ICL3310ECA
0 to 70
20 Ld SSOP
M20.209
ICL3310ECA-T
0 to 70
Tape and Reel
M20.209
ICL3310EIB
-40 to 85
18 Ld SOIC
M18.3
ICL3310EIB-T
-40 to 85
Tape and Reel
M18.3
ICL3310EIA
-40 to 85
20 Ld SSOP
M20.209
ICL3310EIA-T
-40 to 85
Tape and Reel
M20.209
• Drop In Replacement for MAX3384ECWN (SOIC)
• Low Power, Pin Compatible Upgrade for 5V MAX222,
SP310E, ADM222, and LT1780
• Single SHDN Pin Disables Transmitters and Receivers
• Meets EIA/TIA-232 and V.28/V.24 Specifications at 3V
• RS-232 Compatible Outputs at 2.7V
• Latch-Up Free
• On-Chip Voltage Converters Require Only Four External
0.1µF Capacitors
• Receiver Hysteresis For Improved Noise Immunity
• Very Low Supply Current . . . . . . . . . . . . . . . . . . . . 0.3mA
• Guaranteed Minimum Data Rate . . . . . . . . . . . . . 250kbps
• Guaranteed Minimum Slew Rate . . . . . . . . . . . . . . . 6V/µs
• Wide Power Supply Range . . . . . . . Single +3V to +5.5V
• Low Supply Current in Powerdown State. . . . . . . . . .<1µA
Applications
• Any System Requiring RS-232 Communication Ports
- Battery Powered, Hand-Held, and Portable Equipment
- Laptop Computers, Notebooks, Palmtops
- Modems, Printers and other Peripherals
- Digital Cameras
- Cellular/Mobile Phones
Related Literature
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
• AN9863, “3V to +5.5V, 250k-1Mbps, RS-232
Transmitters/Receivers”
TABLE 1. SUMMARY OF FEATURES
NO. OF NO. OF
PART NUMBER
Tx.
Rx.
ICL3310E
2
2
1
NO. OF
MONITOR Rx.
(ROUTB)
DATA
RATE
(kbps)
Rx. ENABLE
FUNCTION?
READY
OUTPUT?
MANUAL
POWERDOWN?
AUTOMATIC
POWERDOWN
FUNCTION?
0
250
No
No
Yes
No
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2004. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ICL3310E
Pinouts
ICL3310E (SOIC)
TOP VIEW
ICL3310E (SSOP)
TOP VIEW
20 SHDN
NC 1
18 SHDN
NC 1
C1+ 2
17 VCC
C1+ 2
19 VCC
3
16 GND
V+
3
18 GND
C1- 4
15 T1OUT
C1- 4
17 T1OUT
C2+ 5
14 R1IN
C2+ 5
16 R1IN
C2- 6
13 R1OUT
C2- 6
15 R1OUT
V+
14 NC
V- 7
12 T1IN
V- 7
T2OUT 8
11 T2IN
T2OUT 8
13 T1IN
R2IN 9
12 T2IN
10 R2OUT
R2IN 9
11 NC
R2OUT 10
Pin Descriptions
PIN
VCC
FUNCTION
System power supply input (3.0V to 5.5V).
V+
Internally generated positive transmitter supply (+5.5V).
V-
Internally generated negative transmitter supply (-5.5V).
GND
Ground connection.
C1+
External capacitor (voltage doubler) is connected to this lead.
C1-
External capacitor (voltage doubler) is connected to this lead.
C2+
External capacitor (voltage inverter) is connected to this lead.
C2-
External capacitor (voltage inverter) is connected to this lead.
TIN
TTL/CMOS compatible transmitter Inputs.
TOUT
RIN
±15kV ESD Protected, RS-232 level (nominally ±5.5V) transmitter outputs.
±15kV ESD Protected, RS-232 compatible receiver inputs.
ROUT
TTL/CMOS level receiver outputs.
SHDN
Active low input to shut down transmitters, receivers, and on-board power supply, to place device in low power mode.
Typical Operating Circuits
ICL3310E (NOTE 2)
C3 (OPTIONAL CONNECTION, NOTE 1)
C1
0.1µF
+
C2
0.1µF
+
T1IN
TTL/CMOS
LOGIC LEVELS
+
0.1µF
T2IN
R1OUT
2
4
5
6
+
+3.3V to +5V
17
C1+
VCC
C1C2+
C2-
12
11
V-
2
7
15
T2
8
14
13
5kΩ
C4
0.1µF
T1OUT
T2OUT
R1IN
9
10
NOTES:
1. The negative terminal of C3 can be connected to either VCC or GND.
2. Pin numbers refer to SOIC package.
+ C3
0.1µF
+
T1
R1
R2OUT
3
V+
R2
5kΩ
GND
SHDN
16
R2IN
18
VCC
RS-232
LEVELS
ICL3310E
Absolute Maximum Ratings
Thermal Information
VCC to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V
V+ to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V
V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3V to -7V
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14V
Input Voltages
TIN, SHDN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V
RIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25V
Output Voltages
TOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±13.2V
ROUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC +0.3V
Short Circuit Duration
TOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . See Specification Table
Thermal Resistance (Typical, Note 3)
θJA (°C/W)
18 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . .
75
20 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . .
122
Maximum Junction Temperature (Plastic Package) . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ICL3310ECX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
ICL3310EIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
3. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Test Conditions: VCC = 3V to 5.5V, C1 - C4 = 0.1µF; Unless Otherwise Specified.
Typicals are at TA = 25°C
Electrical Specifications
PARAMETER
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNITS
25
-
0.1
5
µA
Full
-
1
50
µA
Full
-
0.3
3.0
mA
DC CHARACTERISTICS
Supply Current, Powerdown
SHDN = GND
All Outputs Unloaded, SHDN = VCC
Supply Current, Enabled
LOGIC AND TRANSMITTER INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold Low
TIN, SHDN
Full
-
-
0.8
V
Input Logic Threshold High
TIN, SHDN
Full
2.4
-
-
V
Input Leakage Current
TIN, SHDN
Full
-
±0.01
±1.0
µA
Output Leakage Current
SHDN = GND
Full
-
±0.05
±10
µA
Output Voltage Low
IOUT = 3.2mA
Full
-
-
0.4
V
Output Voltage High
IOUT = -1.0mA
Full
-
V
VCC -0.6 VCC -0.1
RECEIVER INPUTS
Input Voltage Range
Full
-25
-
25
V
1.2
-
V
Input Threshold Low
VCC = 3.3V
25
0.6
VCC = 5.0V
Full
0.8
1.5
-
V
Input Threshold High
VCC = 3.3V
25
-
1.5
2.4
V
VCC = 5.0V
Full
-
1.8
2.4
V
Input Hysteresis
Full
0.2
0.5
1
V
Input Resistance
Full
3
5
7
kΩ
TRANSMITTER OUTPUTS
Output Voltage Swing
All Transmitter Outputs Loaded with 3kΩ to Ground
Full
±5.0
±5.4
-
V
Output Resistance
VCC = V+ = V- = 0V, Transmitter Output = ±2V
Full
300
10M
-
Ω
Full
±7
±35
-
mA
VOUT = ±12V, VCC = 0V or 3V to 5.5V, SHDN = GND
Full
-
-
±10
µA
RL = 3kΩ, CL = 1000pF, One Transmitter Switching
Full
250
500
-
kbps
Output Short-Circuit Current
Output Leakage Current
TIMING CHARACTERISTICS
Maximum Data Rate
3
ICL3310E
Test Conditions: VCC = 3V to 5.5V, C1 - C4 = 0.1µF; Unless Otherwise Specified.
Typicals are at TA = 25°C (Continued)
Electrical Specifications
PARAMETER
TEST CONDITIONS
Transmitter Propagation Delay
Receiver Propagation Delay
TEMP
(°C)
MIN
TYP
MAX
UNITS
Transmitter Input to
Transmitter Output,
CL = 1000pF
tPHL
Full
-
0.6
3.5
µs
tPLH
Full
-
0.7
3.5
µs
Receiver Input to Receiver
Output, CL = 150pF
tPHL
Full
-
0.2
1
µs
tPLH
Full
-
0.3
1
µs
Transmitter Output Enable Time
From SHDN Rising Edge to TOUT = ±3V
25
-
50
-
µs
Transmitter Output Disable Time
From SHDN Falling Edge to TOUT = ±5V
25
-
600
-
ns
Transmitter Skew
tPHL - tPLH (Note 4)
25
-
100
-
ns
Receiver Skew
tPHL - tPLH
25
-
100
-
ns
Transition Region Slew Rate
VCC = 3.3V, CL = 150pF to
RL = 3kΩ to 7kΩ,
Measured From 3V to -3V or 2500pF
-3V to 3V
VCC = 4.5V, CL = 150pF to
2500pF
25
4
-
-
V/µs
25
6
-
-
V/µs
Human Body Model
25
-
±15
-
kV
IEC61000-4-2 Contact Discharge
25
-
±8
-
kV
IEC61000-4-2 Air Gap Discharge
25
-
±15
-
kV
Human Body Model
25
-
±3
-
kV
ESD PERFORMANCE
RS-232 Pins (TOUT, RIN)
All Other Pins
NOTE:
4. Transmitter skew is measured at the transmitter zero crossing points.
Detailed Description
The ICL3310E operates from a single +3V to +5.5V supply,
guarantees a 250kbps minimum data rate, requires only four
small external 0.1µF capacitors, features low power
consumption, and meets all ElA RS-232C and V.28
specifications. The circuit is divided into three sections: The
charge pump, the transmitters, and the receivers.
Charge-Pump
Intersil’s new ICL3310E utilizes regulated on-chip dual
charge pumps as voltage doublers, and voltage inverters to
generate ±5.5V transmitter supplies from a VCC supply as
low as 3.0V. This allows these devices to maintain RS-232
compliant output levels over the ±10% tolerance range of
3.3V powered systems. The efficient on-chip power supplies
require only four small, external 0.1µF capacitors for the
voltage doubler and inverter functions over the full VCC
range. The charge pumps operate discontinuously (i.e., they
turn off as soon as the V+ and V- supplies are pumped up to
the nominal values), resulting in significant power savings.
All transmitter outputs disable and assume a high
impedance state when the device enters the powerdown
mode (see Table 2). These outputs may be driven to ±12V
when disabled.
All devices guarantee a 250kbps data rate for full load
conditions (3kΩ and 1000pF), VCC ≥ 3.0V, with one
transmitter operating at full speed. Under more typical
conditions of VCC ≥ 3.3V, RL = 3kΩ, and CL = 250pF, one
transmitter easily operates at 900kbps.
Transmitter inputs float if left unconnected (there are no pullup resistors), and may cause ICC increases. Connect
unused inputs to GND for the best performance.
TABLE 2. POWERDOWN AND ENABLE LOGIC TRUTH TABLE
SHDN TRANSMITTER RECEIVER
INPUT
OUTPUTS
OUTPUTS MODE OF OPERATION
H
Active
Active
Normal Operation
L
High-Z
High-Z
Manual Powerdown
Transmitters
Receivers
The transmitters are proprietary, low dropout, inverting
drivers that translate TTL/CMOS inputs to EIA/TIA-232
output levels. Coupled with the on-chip ±5.5V supplies,
these transmitters deliver true RS-232 levels over a wide
range of single supply system voltages.
The ICL3310E contains standard inverting receivers that
three-state via the SHDN control line. Receivers driving
powered down peripherals must be disabled to prevent
current flow through the peripheral’s protection diodes (see
Figures 2 and 3).
4
ICL3310E
All the receivers convert RS-232 signals to CMOS output
levels and accept inputs up to ±30V while presenting the
required 3kΩ to 7kΩ input impedance (see Figure 1) even if
the power is off (VCC = 0V). The receivers’ Schmitt trigger
input stage uses hysteresis to increase noise immunity and
decrease errors due to slow input signal transitions.
VCC
RXOUT
RXIN
-25V ≤ VRIN ≤ +25V
GND ≤ VROUT ≤ VCC
5kΩ
GND
FIGURE 1. INVERTING RECEIVER CONNECTIONS
Low Power Operation
This 3V device requires a nominal supply current of 0.3mA,
even at VCC = 5.5V, during normal operation (not in
powerdown mode). This is considerably less than the 11mA
current required by comparable 5V RS-232 devices, allowing
users to reduce system power simply by replacing the old
style device with the ICL3310E.
Low Power, Pin Compatible Replacement
Pin compatibility with existing 5V products (e.g., MAX222),
coupled with the wide operating supply range, make the
ICL3310E a potential lower power, higher performance dropin replacement for existing 5V applications. As long as the
VCC
When replacing a device in an existing 5V application, it is
acceptable to terminate C3 to VCC as shown on the “Typical
Operating Circuit”. Nevertheless, terminate C3 to GND if
possible, as slightly better performance results from this
configuration.
Powerdown Functionality
The already low current requirement drops significantly
when the device enters powerdown mode. In powerdown,
supply current drops to 1µA, because the on-chip charge
pump turns off (V+ collapses to VCC, V- collapses to GND),
and the transmitter and receiver outputs three-state. This
micro-power mode makes these devices ideal for battery
powered and portable applications.
Software Controlled (Manual) Powerdown
The ICL3310E may be forced into its low power, standby
state via a simple shutdown (SHDN) pin (see Figure 4).
Driving this pin high enables normal operation, while driving
it low forces the IC into it’s powerdown state. The time
required to exit powerdown, and resume transmission is less
than 50µs. Connect SHDN to VCC if the powerdown function
isn’t needed.
VCC
VCC
TRANSITION
DETECTOR
CURRENT
FLOW
VCC
TO
WAKE-UP
LOGIC
VOUT = VCC
Rx
ICL3310E
V-
VCC
POWERED
DOWN
UART
RX
Tx
GND
±5V RS-232 output swings are acceptable, and transmitter
pull-up resistors aren’t required, the ICL3310E should work
in most 5V applications.
SHDN = GND
OLD
RS-232 CHIP
VOUT = HI-Z
POWERED
DOWN
UART
TX
FIGURE 2. POWER DRAIN THROUGH POWERED DOWN
PERIPHERAL
FIGURE 3. DISABLED RECEIVERS PREVENT POWER DRAIN
5
ICL3310E
that the transmitters enable only when the magnitude of the
supplies exceed approximately 3V.
SHDN
PWR
MGT
LOGIC
5V/DIV
SHDN
ICL3310E
I/O
UART
T1
2V/DIV
CPU
T2
VCC = +3.3V
C1 - C4 = 0.1µF
TIME (20µs/DIV)
FIGURE 4. CONNECTIONS FOR MANUAL POWERDOWN
FIGURE 5. TRANSMITTER OUTPUTS WHEN EXITING
POWERDOWN
Capacitor Selection
The charge pumps require 0.1µF or greater capacitors for
operation with 3.3V ≤ VCC ≤ 5.5V. Increasing the capacitor
values (by a factor of 2) reduces ripple on the transmitter
outputs and slightly reduces power consumption. C2, C3,
and C4 can be increased without increasing C1’s value,
however, do not increase C1 without also increasing C2, C3,
and C4 to maintain the proper ratios (C1 to the other
capacitors).
When using minimum required capacitor values, make sure
that capacitor values do not degrade excessively with
temperature. If in doubt, use capacitors with a larger nominal
value. The capacitor’s equivalent series resistance (ESR)
usually rises at low temperatures and it influences the
amount of ripple on V+ and V-.
Operation Down to 2.7V
ISL3310E transmitter outputs meet RS-562 levels (±3.7V), at
the full data rate, with VCC as low as 2.7V. RS-562 levels
typically ensure interoperability with RS-232 devices.
High Data Rates
The ICL3310E maintains the RS-232 ±5V minimum
transmitter output voltages even at high data rates. Figure 6
details a transmitter loopback test circuit, and Figure 7
illustrates the loopback test result at 120kbps. For this test,
all transmitters were simultaneously driving RS-232 loads in
parallel with 1000pF, at 120kbps. Figure 8 shows the
loopback results for a single transmitter driving 1000pF and
an RS-232 load at 250kbps. The static transmitter was also
loaded with an RS-232 receiver.
VCC
+
C1
Transmitter Outputs when Exiting
Powerdown
Figure 5 shows the response of two transmitter outputs
when exiting powerdown mode. As they activate, the two
transmitter outputs properly go to opposite RS-232 levels,
with no glitching, ringing, nor undesirable transients. Each
transmitter is loaded with 3kΩ in parallel with 2500pF. Note
6
C1+
VCC
V+
C1+
C2
ICL3310E
V-
C2+
C2-
Power Supply Decoupling
In most circumstances a 0.1µF bypass capacitor is
adequate. In applications that are particularly sensitive to
power supply noise, decouple VCC to ground with a
capacitor of the same value as the charge-pump capacitor C1.
Connect the bypass capacitor as close as possible to the IC.
+
0.1µF
TIN
ROUT
+
C3
C4
+
TOUT
RIN
1000pF
5K
VCC
SHDN
FIGURE 6. TRANSMITTER LOOPBACK TEST CIRCUIT
ICL3310E
±15kV ESD Protection
5V/DIV
All pins on ICL3310 devices include ESD protection
structures, but the ICL3310E incorporates advanced
structures which allow the RS-232 pins (transmitter outputs
and receiver inputs) to survive ESD events up to ±15kV. The
RS-232 pins are particularly vulnerable to ESD damage
because they typically connect to an exposed port on the
exterior of the finished product. Simply touching the port
pins, or connecting a cable, can cause an ESD event that
might destroy unprotected ICs. These new ESD structures
protect the device whether or not it is powered up, protect
without allowing any latchup mechanism to activate, and
don’t interfere with RS-232 signals as large as ±25V.
T1IN
T1OUT
R1OUT
VCC = +3.3V
C1 - C4 = 0.1µF
5µs/DIV
Human Body Model (HBM) Testing
FIGURE 7. LOOPBACK TEST AT 120kbps
5V/DIV
T1IN
T1OUT
As the name implies, this test method emulates the ESD
event delivered to an IC during human handling. The tester
delivers the charge through a 1.5kΩ current limiting resistor,
making the test less severe than the IEC61000 test which
utilizes a 330Ω limiting resistor. The HBM method
determines an ICs ability to withstand the ESD transients
typically present during handling and manufacturing. Due to
the random nature of these events, each pin is tested with
respect to all other pins. The RS-232 pins on “E” family
devices can withstand HBM ESD events to ±15kV.
IEC61000-4-2 Testing
R1OUT
VCC = +3.3V
C1 - C4 = 0.1µF
2µs/DIV
FIGURE 8. LOOPBACK TEST AT 250kbps
Interconnection with 3V and 5V Logic
The ICL3310E directly interfaces with 5V CMOS and TTL
logic families. Nevertheless, with the device at 3.3V, and the
logic supply at 5V, AC, HC, and CD4000 outputs can drive
ICL3310E inputs, but ICL3310E outputs do not reach the
minimum VIH for these logic families. See Table 4 for more
information.
TABLE 3. LOGIC FAMILY COMPATIBILITY WITH VARIOUS
SUPPLY VOLTAGES
VCC
SYSTEM
POWER-SUPPLY SUPPLY
VOLTAGE
VOLTAGE
(V)
(V)
3.3
3.3
5
5
5
3.3
COMPATIBILITY
Compatible with all CMOS
families.
Compatible with all TTL and
CMOS logic families.
Compatible with ACT and HCT
CMOS, and with TTL. ICL3310E
outputs are incompatible with AC,
HC, and CD4000 CMOS inputs.
7
The IEC61000 test method applies to finished equipment,
rather than to an individual IC. Therefore, the pins most likely
to suffer an ESD event are those that are exposed to the
outside world (the RS-232 pins in this case), and the IC is
tested in its typical application configuration (power applied)
rather than testing each pin-to-pin combination. The lower
current limiting resistor coupled with the larger charge
storage capacitor yields a test that is much more severe than
the HBM test. The extra ESD protection built into this
device’s RS-232 pins allows the design of equipment
meeting level 4 criteria without the need for additional board
level protection on the RS-232 port.
AIR-GAP DISCHARGE TEST METHOD
For this test method, a charged probe tip moves toward the
IC pin until the voltage arcs to it. The current waveform
delivered to the IC pin depends on approach speed,
humidity, temperature, etc., so it is difficult to obtain
repeatable results. The “E” device RS-232 pins withstand
±15kV air-gap discharges.
CONTACT DISCHARGE TEST METHOD
During the contact discharge test, the probe contacts the
tested pin before the probe tip is energized, thereby
eliminating the variables associated with the air-gap
discharge. The result is a more repeatable and predictable
test, but equipment limits prevent testing devices at voltages
higher than ±8kV. All “E” family devices survive ±8kV contact
discharges on the RS-232 pins.
ICL3310E
Typical Performance Curves
VCC = 3.3V, TA = 25°C
25
VOUT+
4.0
20
2.0
SLEW RATE (V/µs)
TRANSMITTER OUTPUT VOLTAGE (V)
6.0
1 TRANSMITTER AT 250kbps
1 TRANSMITTER AT 30kbps
0
-2.0
15
-SLEW
+SLEW
10
VOUT -
-4.0
-6.0
0
1000
2000
3000
4000
5
5000
0
1000
FIGURE 9. TRANSMITTER OUTPUT VOLTAGE vs LOAD
CAPACITANCE
3.5
40
30
25
120kbps
20
15
4000
5000
NO LOAD
ALL OUTPUTS STATIC
3.0
250kbps
35
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
3000
FIGURE 10. SLEW RATE vs LOAD CAPACITANCE
45
20kbps
10
2.5
2.0
1.5
1.0
0.5
5
0
2000
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
0
1000
2000
3000
4000
5000
LOAD CAPACITANCE (pF)
FIGURE 11. SUPPLY CURRENT vs LOAD CAPACITANCE
WHEN TRANSMITTING DATA
Die Characteristics
SUBSTRATE POTENTIAL (POWERED UP)
GND
TRANSISTOR COUNT
338
PROCESS
Si Gate CMOS
8
0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
SUPPLY VOLTAGE (V)
FIGURE 12. SUPPLY CURRENT vs SUPPLY VOLTAGE
6.0
ICL3310E
Small Outline Plastic Packages (SOIC)
N
INDEX
AREA
0.25(0.010) M
H
M18.3 (JEDEC MS-013-AB ISSUE C)
B M
18 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE
E
INCHES
-B-
1
2
3
L
SEATING PLANE
-A-
h x 45o
A
D
-C-
e
µα
A1
B
0.25(0.010) M
0.10(0.004)
C A M
MIN
MAX
MIN
MAX
NOTES
A
0.0926
0.1043
2.35
2.65
-
A1
0.0040
0.0118
0.10
0.30
-
B
0.013
0.0200
0.33
0.51
9
C
0.0091
0.0125
0.23
0.32
-
D
0.4469
0.4625
11.35
11.75
3
E
0.2914
0.2992
7.40
7.60
4
e
C
B S
0.050 BSC
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above
the seating plane, shall not exceed a maximum value of 0.61mm
(0.024 inch)
10. Controlling dimension: MILLIMETER. Converted inch dimensions are
not necessarily exact.
9
1.27 BSC
-
H
0.394
0.419
10.00
10.65
-
h
0.010
0.029
0.25
0.75
5
L
0.016
0.050
0.40
1.27
6
8o
0o
N
NOTES:
MILLIMETERS
SYMBOL
α
18
0o
18
7
8o
Rev. 0 12/93
ICL3310E
Shrink Small Outline Plastic Packages (SSOP)
M20.209 (JEDEC MO-150-AE ISSUE B)
N
20 LEAD SHRINK SMALL OUTLINE PLASTIC PACKAGE
INDEX
AREA
H
0.25(0.010) M
B M
INCHES
E
-B1
2
3
0.25
0.010
SEATING PLANE
-A-
SYMBOL
GAUGE
PLANE
L
A
D
-C-
α
e
B
C
0.10(0.004)
0.25(0.010) M
C A M
B S
MAX
MILLIMETERS
MIN
MAX
NOTES
A
0.068
0.078
1.73
1.99
A1
0.002
0.008’
0.05
0.21
A2
0.066
0.070’
1.68
1.78
B
0.010’
0.015
0.25
0.38
C
0.004
0.008
0.09
0.20’
D
0.278
0.289
7.07
7.33
3
E
0.205
0.212
5.20’
5.38
4
e
A2
A1
MIN
0.026 BSC
0.65 BSC
H
0.301
0.311
7.65
7.90’
L
0.025
0.037
0.63
0.95
8 deg.
0 deg.
N
α
20
0 deg.
9
6
20
7
8 deg.
NOTES:
Rev. 3 11/02
1. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate
burrs. Mold flash, protrusion and gate burrs shall not exceed
0.20mm (0.0078 inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.20mm (0.0078
inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual
index feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. Dimension “B” does not include dambar protrusion. Allowable
dambar protrusion shall be 0.13mm (0.005 inch) total in excess
of “B” dimension at maximum material condition.
10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
10
Similar pages