RSG CXOSESM5 Cxo oscillator Datasheet

CXO OSCILLATOR
300 kHz to 170 MHz
Low Profile Miniature Surface Mount
Crystal Oscillator
™
DESCRIPTION
Statek’s surface-mount CXO oscillators consist of a Statek
miniature quartz crystal and a CMOS/TTL compatible hybrid
circuit in a low-profile ceramic package with a small footprint.
In addition to the conventional solder or epoxy electrical
connection techniques, bond pads on the topside of the CXO
allow it to be connected electrically in a hybrid assembly using
wire bonds.
0
033
M
T60
actual size
side view
FEATURES
Designed for surface mount applications using infrared,
vapor phase, or epoxy mount techniques
CMOS and TTL compatible
PACKAGE DIMENSIONS
Low power consumption
Optional Output Enable/Disable with Tri-State
3
2
2
3
Low EMI emission
High shock resistance
E
Full military testing available
Hermetically sealed ceramic package
A
Wire bond pads for hybrids
D
TOP
BOTTOM
APPLICATIONS
Military & Aerospace
Smart munitions
1
4
Cockpit systems
1
B
Navigation
C
4
F
Industrial, Computer & Communications
Industrial controls
TYPICAL
Instrumentation
Microprocessor clocks
DIM
A
inches
0.400
mm
10.16
inches
0.405
mm
10.29
B
0.180
4.57
0.190
4.83
C (SM1)
Medical
Infusion pumps
SUGGESTED LAND PATTERN
0.275 (6.99)
0.130 (3.30)
0.070 (1.78)
MAXIMUM
0.051
1.30
0.055
1.40
C (SM3/SM5) 0.055
1.40
0.063
1.60
D
0.340
8.64
0.350
8.89
E
0.125
3.18
0.135
3.43
F
0.050
1.27
0.060
1.52
PIN CONNECTIONS
1. Enable/Disable (E or T) or not connected (N)
0.060 (1.52)
2. Ground
3. Output
GRID
PLACEMENT
COURTYARD
4. VDD
0.135 (3.43)
10106 Rev F
inches (mm)
Änderungen vorbehalten / subject to change without notice
■
■
YS
90
■
■
01
TEM
C ERT I F I C
AT
N
IO
■
IS O
Distribution:
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de
S
0.140 (3.56)
Pb
SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications are typical at 25OC unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage VDD
-0.5 V to 7.0 V
Storage Temperature
-55OC to +125OC
Maximum Process Temperature 260OC for 20 seconds
Supply Voltage1
5.0 V +_ 10%
3.3 V +_ 10%
+
3
_ 100 ppm
Calibration Tolerance
+
_
Frequency Stability
50 ppm for Commercial
+
4
_ 100 ppm for Industrial
Over Temperature
+
_ 100 ppm for Military
Supply Current
3.3 V
5.0 V
(Typical)
10 MHz
2 mA
4 mA
24 MHz
4 mA
8 mA
30 MHz
6 mA
10 mA
40 MHz
8 mA
12 mA
50 MHz
10 mA
14 mA
CMOS5
15 pF
Start-up Time
5 ms MAX
Rise/Fall Time
6 ns MAX
Duty Cycle
40% MIN, 60% MAX
Aging, first year
10 ppm MAX
6
Shock, survival
3,000 g, 0.3 ms, 1/2 sine
7
Vibration, survival
20 g , 10-2000 Hz swept sine
Operating Temp. Range -10OC to +70OC (Commercial)
-40OC to +85OC (Industrial)
-55OC to +125OC (Military)
300 kHz to 120 MHz2
300 kHz to 170 MHz2
ENABLE/DISABLE OPTIONS (E/T/N)
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the
T-version. So, the E-version offers very low current
consumption when the oscillator is disabled and the
T-version offers very fast output recovery when the
oscillator is re-enabled. The N-version does not have
PIN 1 connected internally and so has no enable/disable
capability. The following table summarizes the three
options.
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND T
E
When enabled (PIN 1 is high*)
1.
2.
3.
4.
5.
6.
7.
Other voltages available. Contact factory.
Not all frequencies available at all voltage/enable combinations.
Other tolerances available.
Does not include calibration tolerance. Other tolerances available.
Higher CMOS loads and TTL loads available. Contact factory.
Higher shock version available. Contact factory about CXOHG.
Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
available.
Note: All parameters are measured at ambient temperature with a 10M Ω,15 pF load.
Output
Freq. output
Freq. output
Oscillator
Oscillates
Oscillates
Current consumption
Normal
Normal
Output
High Z state
High Z state
Oscillator
Stops
Oscillates
Current consumption
Very low
Lower than normal
When disabled (PIN 1 is low)
When re-enabled (PIN 1 changes from low to high)
Output recovery
PACKAGING OPTIONS
CXO
T
Delayed
Immediate
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
- Tray Pack
- 16 mm tape, 7˝ or 13˝ reels
Per EIA 418 (see Tape and Reel data sheet 10109)
HOW TO ORDER CXO SURFACE MOUNT CRYSTAL OSCILLATORS
S
“S” if special,
custom design,
or if the voltage
is not 5.0 V.
Otherwise,
leave blank.
T
SM3
Enable/Disable Option
E, T or N
32.0M ,
Terminations
Frequency
Blank = SM1
K = kHz
= Gold Plated
M = MHz
SM3 = Solder Dipped
SM5 = Solder Dipped
Lead Free
100
/
Calibration
Tolerance
@ 250C
(in ppm)
100
/
/
Frequency
Stability over
Temp.Range
(in ppm)
I
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
OR
/
/
200
Total
Frequency
Tolerance
(in ppm)
/
I
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
■
■
■
■
10106 Rev F
YS
■
IS O
90
01
TEM
C ERT I F I C
AT
N
IO
Distribution:
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
Tel. +49CORPORATION
69 984047-0 Fax
+49
984047-77
[email protected]
www.rsg-electronic.de
STATEK
512
N.69
MAIN
ST., ORANGE,
CA 92868 714-639-7810
FAX: 714-997-1256 www.statek.com
Änderungen vorbehalten / subject to change without notice
S
CXO
Pb
Similar pages