TI CD74HCT221M High speed cmos logic dual monostable multivibrator with reset Datasheet

[ /Title
(CD74
HC221
,
CD74
HCT22
1)
/Subject
(High
Speed
CMOS
Logic
Dual
Monos
table
Multi-
CD74HC221,
CD74HCT221
Data sheet acquired from Harris Semiconductor
SCHS166A
High Speed CMOS Logic
Dual Monostable Multivibrator with Reset
November 1997 - Revised April 1999
Features
Description
• Overriding RESET Terminates Output Pulse
The CD74HC221, and CH74HCT221 are dual monostable
multivibrators with reset. An external resistor (RX) and an
external capacitor (CX) control the timing and the accuracy
for the circuit. Adjustment of RX and CX provides a wide
range of output pulse widths from the Q and Q terminals.
Pulse triggering on the B input occurs at a particular voltage
level and is not related to the rise and fall time of the trigger
pulse.
• Triggering from the Leading or Trailing Edge
• Q and Q Buffered Outputs
• Separate Resets
• Wide Range of Output-Pulse Widths
• Schmitt Trigger on B Inputs
• Fanout (Over Temperature Range)
- Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads
- Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads
Once triggered, the outputs are independent of further trigger
inputs on A and B. The output pulse can be terminated by a
LOW level on the Reset (R) pin. Trailing Edge triggering (A)
and leading-edge-triggering (B) inputs are provided for
triggering from either edge of the input pulse. On power up,
the IC is reset. If either Mono is not used each input (on the
unused device) must be terminated either high or low.
• Wide Operating Temperature Range . . . -55oC to 125oC
• Balanced Propagation Delay and Transition Times
• Significant Power Reduction Compared to LSTTL
Logic ICs
The minimum value of external resistance, RX, is typically 500Ω.
The minimum value of external capacitance, CX, is 0pF. The
calculation for the pulse width is tW = 0.7 RXCX at VCC = 4.5V.
• HC Types
- 2V to 6V Operation
- High Noise Immunity: NIL = 30%, NIH = 30% of VCC
at VCC = 5V
Ordering Information
• HCT Types
- 4.5V to 5.5V Operation
- Direct LSTTL Input Logic Compatibility,
VIL= 0.8V (Max), VIH = 2V (Min)
- CMOS Input Compatibility, Il ≤ 1µA at VOL, VOH
PART NUMBER
TEMP. RANGE (oC)
PKG.
NO.
PACKAGE
CD74HC221E
-55 to 125
16 Ld PDIP
E16.3
CD74HCT221E
-55 to 125
16 Ld PDIP
E16.3
CD74HC221M
-55 to 125
16 Ld SOIC
M16.15
CD74HCT221M
-55 to 125
16 Ld SOIC
M16.15
NOTES:
1. When ordering, use the entire part number. Add the suffix 96 to
obtain the variant in the tape and reel.
2. Wafer or die are available which meets all electrical
specifications. Please contact your local sales office or Harris
customer service for ordering information.
Pinout
CD74HC221, CD74HCT221
(PDIP, SOIC)
TOP VIEW
1A 1
16 VCC
1B 2
15 1CXRX
1R 3
14 1CX
1Q 4
13 1Q
2Q 5
12 2Q
2CX 6
11 2R
2CXRX 7
10 2B
GND 8
9 2A
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright
© Harris Corporation 1997
1
File Number
1670.1
CD74HC221, CD74HCT221
Functional Diagram
1CX
1RX
VCC
14
15
1CX
1CXRX
13
1Q
1A
1
MONO 1
4
1B
1Q
2
1R
2R
3
11
5
9
2Q
2A
MONO 2
10
12
2B
2Q
2CX
2CXRX
6
7
VCC
2CX
2RX
TRUTH TABLE
INPUTS
OUTPUTS
A
B
R
Q
Q
H
X
H
L
H
X
L
H
L
H
L
↑
H
↓
H
H
X
X
L
L
H
L
H
↑
(Note 3)
(Note 3)
NOTE:
H = High Voltage Level, L = Low Voltage Level, X = Irrelevant, ↑ = Transition from Low
to High Level, ↓ = Transition from High to Low Level,
= One High Level Pulse,
= One Low Level Pulse
3. For this combination the reset input must be low and the following sequence must
be used: pin 1 (or 9) must be set high or pin 2 (or 10) set low; then pin 1 (or 9)
must be low and pin 2 (or 10) set high. Now the reset input goes from low-to-high
and the device will be triggered.
2
CD74HC221, CD74HCT221
Logic Diagram
VCC
16
C
P
RX
N
A
B
1 (9)
R
3 (11)
2 (10)
P
VCC
R
D
RESET
FF
S
C
Q
R
P
OP
AMP
R2
RXCX
C
VCC
MIRROR VOLTAGE
QM
15 (7)
+
QM
R3
PP
CX
R
MASK
FF
S
Q
MAIN
FF
R1
R4
Q
N
VCC
14 (6)
PULLDOWN
FF
D
CX
Q
N
8
C
4 (12)
C
(13) 5
Q
GND
R
Q
Q
+
OP AMP
3
CD74HC221, CD74HCT221
Absolute Maximum Ratings
Thermal Information
DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V
DC Input Diode Current, IIK
For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA
DC Output Diode Current, IOK
For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA
DC Drain Current, per Output, IO
For -0.5V < VO < VCC + 0.5V. . . . . . . . . . . . . . . . . . . . . . . . . .±25mA
DC Output Source or Sink Current per Output Pin, IO
For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA
DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .±50mA
Thermal Resistance (Typical, Note 4)
θJA (oC/W) θJC (oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . .
100
N/A
SOIC Package . . . . . . . . . . . . . . . . . . .
180
N/A
Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
Operating Conditions
Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
Supply Voltage Range, VCC
HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V
HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V
DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC
Input Rise and Fall Time, tr, tf on Inputs A and R
2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max)
4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max)
6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max)
Input Rise and Fall Time, tr, tf on Input B
2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited ns (Max)
4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited ns (Max)
6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited ns (Max)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
4. θJA is measured with the component mounted on an evaluation PC board in free air.
DC Electrical Specifications
TEST
CONDITIONS
SYMBOL
VI (V)
IO (mA)
High Level Input
Voltage
VIH
-
-
Low Level Input
Voltage
VIL
High Level Output
Voltage
CMOS Loads
VOH
PARAMETER
VCC
(V)
25oC
MIN
TYP
-40oC TO 85oC -55oC TO 125oC
MAX
MIN
MAX
MIN
MAX
UNITS
HC TYPES
-
VIH or VIL
High Level Output
Voltage
TTL Loads
Low Level Output
Voltage
CMOS Loads
Low Level Output
Voltage
TTL Loads
VOL
VIH or VIL
-
2
1.5
-
-
1.5
-
1.5
-
V
4.5
3.15
-
-
3.15
-
3.15
-
V
6
4.2
-
-
4.2
-
4.2
-
V
2
-
-
0.5
-
0.5
-
0.5
V
4.5
-
-
1.35
-
1.35
-
1.35
V
6
-
-
1.8
-
1.8
-
1.8
V
-0.02
2
1.9
-
-
1.9
-
1.9
-
V
-0.02
4.5
4.4
-
-
4.4
-
4.4
-
V
-0.02
6
5.9
-
-
5.9
-
5.9
-
V
-
-
-
-
-
-
-
-
-
V
-4
4.5
3.98
-
-
3.84
-
3.7
-
V
-5.2
6
5.48
-
-
5.34
-
5.2
-
V
0.02
2
-
-
0.1
-
0.1
-
0.1
V
0.02
4.5
-
-
0.1
-
0.1
-
0.1
V
0.02
6
-
-
0.1
-
0.1
-
0.1
V
-
-
-
-
-
-
-
-
-
V
4
4.5
-
-
0.26
-
0.33
-
0.4
V
5.2
6
-
-
0.26
-
0.33
-
0.4
V
4
CD74HC221, CD74HCT221
DC Electrical Specifications
(Continued)
TEST
CONDITIONS
25oC
-40oC TO 85oC -55oC TO 125oC
SYMBOL
VI (V)
IO (mA)
VCC
(V)
II
VCC or
GND
-
6
-
-
±0.1
-
±1
-
±1
µA
ICC
VCC or
GND
0
6
-
-
8
-
80
-
160
µA
High Level Input
Voltage
VIH
-
-
4.5 to
5.5
2
-
-
2
-
2
-
V
Low Level Input
Voltage
VIL
-
-
4.5 to
5.5
-
-
0.8
-
0.8
-
0.8
V
High Level Output
Voltage
CMOS Loads
VOH
VIH or VIL
-0.02
4.5
4.4
-
-
4.4
-
4.4
-
V
-4
4.5
3.98
-
-
3.84
-
3.7
-
V
0.02
4.5
-
-
0.1
-
0.1
-
0.1
V
4
4.5
-
-
0.26
-
0.33
-
0.4
V
±0.1
-
±1
-
±1
µA
PARAMETER
Input Leakage
Current
Quiescent Device
Current
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
HCT TYPES
High Level Output
Voltage
TTL Loads
Low Level Output
Voltage
CMOS Loads
VOL
VIH or VIL
Low Level Output
Voltage
TTL Loads
Input Leakage
Current
Quiescent Device
Current
Additional Quiescent
Device Current Per
Input Pin: 1 Unit Load
II
VCC and
GND
0
5.5
-
ICC
VCC or
GND
0
5.5
-
-
8
-
80
-
160
µA
∆ICC
VCC
-2.1
-
4.5 to
5.5
-
100
360
-
450
-
490
µA
NOTE: For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA.
HCT Input Loading Table
INPUT
UNIT LOADS
All Inputs
0.3
NOTE: Unit Load is ∆ICC limit specified in DC Electrical Table, e.g.,
360µA max at 25oC.
Prerequisite For Switching Function
25oC
PARAMETER
-40oC TO 85oC
-55oC TO 125oC
SYMBOL
VCC (V)
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
tWL
2
70
-
-
90
-
105
-
ns
HC TYPES
Input Pulse Width
A
Input Pulse Width
B
tWH
4.5
14
-
-
18
-
21
-
ns
6
12
-
-
15
-
18
-
ns
2
70
-
-
90
-
105
-
ns
4.5
14
-
-
18
-
21
-
ns
6
12
-
-
15
-
18
-
ns
5
CD74HC221, CD74HCT221
Prerequisite For Switching Function
(Continued)
25oC
PARAMETER
Input Pulse Width
Reset
-40oC TO 85oC
-55oC TO 125oC
SYMBOL
VCC (V)
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
tWL
2
70
-
-
90
-
105
-
ns
4.5
14
-
-
18
-
21
-
ns
6
12
-
-
15
-
18
-
ns
2
0
-
-
0
-
0
-
ns
4.5
0
-
-
0
-
0
-
ns
Recovery Time
R to A or B
tSU
6
0
-
-
0
-
0
-
ns
Output Pulse Width Q or Q
CX = 0.1µF RX = 10kΩ
tW
5
630
-
770
602
798
595
805
µs
Output Pulse Width Q or Q
CX = 28pF, RX = 2kΩ
tW
4.5
-
140
-
-
-
-
-
ns
CX = 1000pF, RX = 2kΩ
tW
4.5
-
1.5
-
-
-
-
-
µs
CX = 1000pF, RX = 10kΩ
tW
4.5
-
7
-
-
-
-
-
µs
Input Pulse Width
A
tWL
4.5
14
-
-
18
-
21
-
ns
Input Pulse Width
B
tWH
4.5
14
-
-
18
-
21
-
ns
Input Pulse Width
Reset
tWL
4.5
18
-
-
23
-
27
-
ns
Recovery Time
R to A or B
tSU
4.5
0
-
-
0
-
0
-
ns
Output Pulse Width Q or Q
CX = 0.1µF RX = 10kΩ
tW
5
630
-
770
602
798
595
805
µs
Output Pulse Width Q or Q
CX = 28pF, RX = 2kΩ
tW
4.5
-
140
-
-
-
-
-
ns
CX = 1000pF, RX = 2kΩ
tW
4.5
-
1.5
-
-
-
-
-
µs
CX = 1000pF, RX = 10kΩ
tW
4.5
-
7
-
-
-
-
-
µs
HCT TYPES
Switching Specifications Input tr, tf = 6ns
PARAMETER
-40oC TO
85oC
25oC
-55oC TO
125oC
SYMBOL
TEST
CONDITIONS
VCC (V)
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
tPLH
CL = 50pF
2
-
-
210
-
265
-
315
ns
CL = 50pF
4.5
-
-
42
-
53
-
63
ns
CL = 50pF
6
-
-
36
-
45
-
54
ns
CL = 15pF
5
-
18
-
-
-
-
-
ns
CL = 50pF
2
-
-
170
-
215
-
255
ns
CL = 50pF
4.5
-
-
34
-
43
-
51
ns
CL = 50pF
6
-
-
29
-
37
-
43
ns
CL = 15pF
5
-
14
-
-
-
-
-
ns
HC TYPES
Propagation Delay,
Trigger A, B, R to Q
Propagation Delay,
Trigger A, B, R to Q
tPHL
6
CD74HC221, CD74HCT221
Switching Specifications Input tr, tf = 6ns
(Continued)
-40oC TO
85oC
25oC
-55oC TO
125oC
SYMBOL
TEST
CONDITIONS
VCC (V)
MIN
TYP
MAX
MIN
MAX
MIN
MAX
UNITS
tPLH
CL = 50pF
2
-
-
160
-
200
-
240
ns
4.5
-
-
32
-
40
-
48
ns
6
-
-
27
-
34
-
41
ns
2
-
-
180
-
225
-
270
ns
4.5
-
-
36
-
45
-
54
ns
6
-
-
31
-
38
-
46
ns
2
-
-
75
-
95
-
110
ns
4.5
-
-
15
-
19
-
22
ns
6
-
-
13
-
16
-
19
ns
-
-
-
-
10
-
10
-
10
pF
-
4.5 to
5.5
-
±2
-
-
-
-
-
%
CPD
-
5
-
166
-
-
-
-
-
pF
Propagation Delay,
Trigger A, B, R to Q
tPLH
CL = 50pF
4.5
-
-
42
-
-
-
63
ns
CL = 15pF
5
-
18
-
-
-
-
-
ns
Propagation Delay,
Trigger A, B, R to Q
tPHL
CL = 50pF
4.5
-
-
34
-
43
-
51
ns
CL = 15pF
5
-
14
-
-
-
-
-
ns
Propagation Delay,
R to Q
tPLH
CL = 50pF
4.5
-
-
38
-
-
-
57
ns
Propagation Delay,
R to Q
tPHL
CL = 50pF
4.5
-
-
37
-
-
-
56
ns
tTLH, tTHL
CL = 50pF
2
-
-
75
-
95
-
110
ns
4.5
-
-
15
-
19
-
22
ns
6
-
-
13
-
16
-
19
ns
-
-
-
-
10
-
10
-
10
pF
-
4.5 to
5.5
-
±2
-
-
-
-
-
%
-
5
-
166
-
-
-
-
-
pF
PARAMETER
Propagation Delay,
R to Q
Propagation Delay,
R to Q
Output Transition Time
Input Capacitance
tPHL
tTLH, tTHL
CIN
Pulse Width Match Between
Circuits in the Same Package
CX = 1000pF, RX = 10kΩ
Power Dissipation Capacitance
(Notes 5, 6)
CL = 50pF
CL = 50pF
HCT TYPES
Output Transition Time
Input Capacitance
CIN
Pulse Width Match Between
Circuits in the Same Package
CX = 1000pF, RX = 10kΩ
Power Dissipation Capacitance
(Notes 5, 6)
CPD
NOTES:
5. CPD is used to determine the dynamic power consumption, per multivibrator.
6. PD = (CPD + CL) VCC2 fi + Σ where fi = input frequency, fo = output frequency, CL = output load capacitance, VCC = supply voltage.
7
CD74HC221, CD74HCT221
Test Circuits and Waveforms
tfCL
trCL
CLOCK
tWL + tWH =
90%
10%
I
fCL
CLOCK
50%
50%
1.3V
0.3V
FIGURE 2. HCT CLOCK PULSE RISE AND FALL TIMES AND
PULSE WIDTH
tf = 6ns
tf = 6ns
tr = 6ns
VCC
90%
50%
10%
GND
tTLH
GND
tTHL
90%
50%
10%
INVERTING
OUTPUT
3V
2.7V
1.3V
0.3V
INPUT
tTHL
GND
tWH
NOTE: Outputs should be switching from 10% VCC to 90% VCC in
accordance with device truth table. For fMAX, input duty cycle = 50%.
FIGURE 1. HC CLOCK PULSE RISE AND FALL TIMES AND
PULSE WIDTH
tr = 6ns
1.3V
1.3V
tWL
tWH
NOTE: Outputs should be switching from 10% VCC to 90% VCC in
accordance with device truth table. For fMAX, input duty cycle = 50%.
tPHL
2.7V
0.3V
GND
tWL
INPUT
tfCL = 6ns
I
fCL
3V
VCC
50%
10%
tWL + tWH =
trCL = 6ns
tTLH
90%
1.3V
10%
INVERTING
OUTPUT
tPHL
tPLH
FIGURE 3. HC TRANSITION TIMES AND PROPAGATION
DELAY TIMES, COMBINATION LOGIC
tPLH
FIGURE 4. HCT TRANSITION TIMES AND PROPAGATION
DELAY TIMES, COMBINATION LOGIC
8
CD74HC221, CD74HCT221
Typical Performance Curves
RX = 10K
RX = 10K
VCC = 5V
TA = 25oC
680
0.9
K FACTOR
tW, PULSE WIDTH (µs)
685
CX = 1µF
675
670
HCT
0.8
0.7
665
-75
-50
-25
0
25
50
75
100
125
150
0.6
175
0
2
4
6
VCC, SUPPLY VOLTAGE (V)
TA, AMBIENT TEMPERATURE (oC)
FIGURE 5. HC/HCT221 OUTPUT PULSE WIDTH vs
TEMPERATURE
10
FIGURE 6. HC/HCT221 K FACTOR vs SUPPLY VOLTAGE
106
106
VCC = 4.5V
VCC = 2V
105
tW, PULSE WIDTH (µs)
105
tW, PULSE WIDTH (µs)
8
104
103
RX = 100K
102
RX = 50K
10
RX = 10K
RX = 2K
1
104
103
102
RX = 100K
10
RX = 10K
RX = 50K
RX = 2K
1
0.1
0.1
10
102
103
104
105
106
107
108
10
CX, TIMING CAPACITANCE (pF)
102
103
104
105
106
107
CX, TIMING CAPACITANCE (pF)
FIGURE 7. HC221 OUTPUT PULSE WIDTH vs CX
FIGURE 8. HC/HCT221 OUTPUT PULSE WIDTH vs CX
9
108
Typical Performance Curves
(Continued)
RX = 10K
RX = 10K
VCC = 5V
TA = 25oC
680
0.9
K FACTOR
tW, PULSE WIDTH (µs)
685
CX = 1µF
675
670
HCT
0.8
0.7
665
-75
-50
-25
0
25
50
75
100
125
150
0.6
175
0
2
TA, AMBIENT TEMPERATURE (oC)
FIGURE 5. HC/HCT221 OUTPUT PULSE WIDTH vs
TEMPERATURE
4
6
VCC, SUPPLY VOLTAGE (V)
FIGURE 6. HC/HCT221 K FACTOR vs SUPPLY VOLTAGE
106
VCC = 6V
tW, PULSE WIDTH (µs)
105
104
103
102
RX = 100K
RX = 50K
10
RX = 10K
RX = 2K
1
0.1
10
102
8
103
104
105
106
107
CX, TIMING CAPACITANCE (pF)
FIGURE 9. HC221 OUTPUT PULSE WIDTH vs CX
10
108
10
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated
Similar pages