Maxim MAX1982 Low-voltage, low-dropout linear regulators with external bias supply Datasheet

KIT
ATION
EVALU
E
L
B
AVAILA
19-2560; Rev 0; 7/02
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
Applications
Notebook Computers
Features
♦ Low-Cost 1.2V, 300mA VID Supply
♦ ±3% Output Voltage Accuracy
♦ No Minimum Load Current Required
♦ 1.25V to 5.5V Input Supply Voltage
♦ 5V Input Bias Supply Voltage
♦ Power-Good (PGOOD) Open-Drain Output with
1ms Rising Edge Propagation Delay (MAX1982)
♦ Adjustable Output Voltage (MAX1983)
♦ Low Supply Current (IBIAS + IIN = 165µA typ)
♦ 5µA (max) Shutdown Supply Current
♦ Tiny 6-Pin SOT23 Package
VID Power Supplies
Ordering Information
PDAs
Cell Phones
Low-Dropout Regulators with External Bias
Supply
PART
TEMP RANGE
PINPACKAGE
TOP
MARK
MAX1982EUT-T
-40°C to +85°C
6 SOT23-6
ABEA
MAX1983EUT-T
-40°C to +85°C
6 SOT23-6
ABEB
Typical Operating Circuit
Pin Configurations
TOP VIEW
4.5V TO 5.5V
IN
BIAS
MAX1982
1.25V TO 5.5V
BIAS 1
0.1µF
GND 2
GND
IN
OUT
ON
MAX1982
5
OUT
4
PGOOD
1.2V
10µF
PGOOD
SHDN
6
10µF
PGOOD
SHDN 3
SOT23-6
Fixed Output Voltage
OFF
100kΩ
BIAS 1
GND 2
SHDN 3
MAX1983
6
IN
5
OUT
4
ADJ
SOT23-6
Adjustable Output
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX1982/MAX1983
General Description
The MAX1982/MAX1983 are low-voltage, low-dropout
linear regulators with an external bias supply input. The
5V bias supply drives the gate of the internal N-channel
pass transistor, making these devices ideal for applications that require low-voltage outputs from low-voltage
inputs. The MAX1982 delivers 1.2V (±3%) at 300mA
from an input voltage of 1.25V to 5.5V. The MAX1983
delivers an adjustable output voltage from 0.8V to 2V.
The MAX1982/MAX1983 include a current-limit and
thermal shutdown that protects the regulator in the
event of a fault condition. Both devices are offered in a
6-pin SOT23 package and are specified over the
extended (-40°C to +85°C) temperature range.
MAX1982/MAX1983
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
ABSOLUTE MAXIMUM RATINGS
ADJ, IN, BIAS, PGOOD, SHDN, OUT to GND..........-0.3V to +6V
Output Short-Circuit Duration ............................................Infinite
Continuous Power Dissipation (TA = +70°C)
6-Pin SOT23 (derate 8.7mW/oC above +70°C)............696mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65oC to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(Circuit of Figure 3, VIN = 1.8V, ILOAD = 1mA, CLOAD = 10µF, TA = 0°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
Input Voltage
VIN
BIAS Voltage
VBIAS
VOUT Voltage Range
VOUT
CONDITIONS
MAX1983
BIAS Input Undervoltage Lockout
MAX
UNITS
1.25
MIN
5.5
V
4.5
5.5
V
0.8
2.0
V
4.35
V
µA
3.8
TYP
4.1
Shutdown Supply Current
IIN
1.25V < VIN < 5.5V
1
5
Quiescent BIAS Current
IQ
4.5V < VBIAS < 5.5V
140
250
µA
Shutdown BIAS Current
I SHDN
4.5V < VBIAS < 5.5V
1
5
µA
VOUT Input Bias Current
MAX1983 ADJ Input Current
MAX1982: VIN = open, VOUT = 1.20V
30
MAX1983: VIN = open, 0.8V < VOUT < 2.0V
0V < VADJ < 2.0V
2
µA
1
µA
-0.15
+0.15
%/V
TA = +25°C, IOUT = 100mA
-1
+1
TA = 0°C to +85°C, IOUT = 1mA to 300mA,
VOUT + 0.5V < VIN < 5.5V
-3
+3
TA = +25°C, IOUT = 100mA
-1
+1
TA = 0°C to +85°C, IOUT = 1mA to 300mA,
VOUT + 0.5V < VIN < 5.5V
-3
+3
REGULATOR CHARACTERISTICS
Line Regulation
∆VOUT/
∆VIN
MAX1982 1.20V
Output Voltage Accuracy
VOUT
MAX1983 0.80V
Output Voltage Accuracy
VOUT
Dropout Voltage
VDO
Current Limit
Thermal-Shutdown Temperature
ILIM
ILOAD = 10mA, 1.5V < VIN < 5.5V
ILOAD = 300mA
350
ILOAD = 150mA
175
VIN - VOUT = 1.3V
330
T SHDN
1400
160
Thermal-Shutdown Hysteresis
RMS Output Noise
600
10Hz to 100kHz
%
%
mV
mA
°C
20
°C
65
µVRMS
PGOOD COMPARATOR
Comparator Threshold
Comparator Hysteresis
2
% of regulated output voltage
VHYST
-12.5
-9
10
_______________________________________________________________________________________
-6
%
mV
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
(Circuit of Figure 3, VIN = 1.8V, ILOAD = 1mA, CLOAD = 10µF, TA = 0°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
LOGIC AND I/O
SHDN Input High Voltage
VIH
SHDN Input Low Voltage
VIL
2.4
SHDN Input Current
V
-1
PGOOD Output Low Voltage
PGOOD sinking 1mA
PGOOD Output
High Leakage Current
0 < VPGOOD < VIN
-1
0.8
V
+1
µA
0.1
V
+1
µA
DYNAMICS
Positive Load Step
tRISE
ILOAD = 1mA to full load, CLOAD = 10µF
10
µs
Negative Load Step
tFALL
ILOAD = full load to 1mA, CLOAD = 10µF
50
µs
10Hz < f < 10kHz, ILOAD = 300mA,
CLOAD = 10µF
-60
dB
ILOAD = 300mA, CLOAD = 10µF, 0% to 90%
of nominal output voltage
100
µs
ILOAD = 300mA, CLOAD = 10µF
0.5
%
Falling edge, 3mV under trip threshold
10
µs
Ripple Rejection at VIN
Startup Response Time
tON
Startup Overshoot
PGOOD Propagation Delay
tPD
Rising edge within 5% of regulation level
1
4
ms
UNITS
ELECTRICAL CHARACTERISTICS
(Circuit of Figure 3, VIN = 1.8V, ILOAD = 1mA, CLOAD = 10µF, TA = -40°C to +85°C, unless otherwise noted.) (Note 1)
MIN
MAX
Input Voltage
PARAMETER
SYMBOL
VIN
CONDITIONS
1.25
5.5
V
BIAS Voltage
VBIAS
4.5
5.5
V
VOUT Voltage Range
VOUT
0.8
2.0
V
3.8
4.2
V
µA
MAX1983
BIAS Input Undervoltage Lockout
Shutdown Supply Current
IIN
1.25V < VIN < 5.5V
5
Quiescent BIAS Current
IQ
4.5V < VBIAS < 5.5V
250
µA
Shutdown BIAS Current
I SHDN
5
µA
VOUT Input Bias Current
4.5V < VBIAS < 5.5V
MAX1982: VIN = open, VOUT = 1.20V
30
MAX1983: VIN = open, 0.8V < VOUT < 2.0V
2
µA
REGULATOR CHARACTERISTICS
∆VOUT/
∆VIN
Line Regulation
MAX1982 1.20V
Output Voltage Accuracy
VOUT
ILOAD = 10mA, 1.5V < VIN < 5.5V
IOUT = 1mA to 300mA,
VOUT + 0.5V < VIN < 5.5V
-0.15
+0.15
%/V
-3
+3
%
_______________________________________________________________________________________
3
MAX1982/MAX1983
ELECTRICAL CHARACTERISTICS (continued)
ELECTRICAL CHARACTERISTICS (continued)
(Circuit of Figure 3, VIN = 1.8V, VOUT = 1.2V, ILOAD = 1mA, CLOAD = 10µF, TA = -40°C to +85°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
MAX1983 0.80V
Output Voltage Accuracy
VOUT
Dropout Voltage
VDO
Current Limit
ILIM
CONDITIONS
MIN
MAX
UNITS
-3
+3
%
IOUT = 1mA to 300mA,
VOUT + 0.5V < VIN < 5.5V
ILOAD = 300mA
350
ILOAD = 150mA
175
VIN - VOUT = 1.3V
mV
330
1400
mA
-12.5
-6
%
0.8
V
+1
µA
0.1
V
PGOOD COMPARATOR
Comparator Threshold
% of regulated output voltage
LOGIC AND I/O
SHDN Input High Voltage
VIH
SHDN Input Low Voltage
VIL
2.4
SHDN Input Current
V
-1
PGOOD Output Low Voltage
PGOOD sinking 1mA
PGOOD Output High Leakage
Current
0 < VPGOOD < VIN
-1
+1
µA
Rising edge within 5% of regulation level
1
4
ms
DYNAMICS
PGOOD Propagation Delay
tPD
Note 1: Specifications over temperature are guaranteed by design, not production tested.
Note 2: VOUT is 1.2V for MAX1982. For MAX1983 VOUT is set to 1.2V with circuit of Figure 4.
Typical Operating Characteristics
(Circuit of Figure 3, TA = +25°C, unless otherwise noted.)
BIAS INPUT CURRENT
vs. INPUT VOLTAGE
28
27
26
25
2.5
140
135
MAX1982/83 toc03
170
165
160
VBIAS = 5V
VIN = 1.8V
130
3.5
INPUT VOLTAGE (V)
4
145
175
VBIAS = 5V
VBIAS = 5V
1.5
GROUND CURRENT vs. OUTPUT CURRENT
MAX1982/83 toc02
29
150
BIAS INPUT CURRENT (µA)
MAX1982/83 toc01
30
GROUND CURRENT (µA)
INPUT CURRENT vs. INPUT VOLTAGE
INPUT CURRENT (µA)
MAX1982/MAX1983
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
4.5
5.5
155
1.5
2.5
3.5
INPUT VOLTAGE (V)
4.5
5.5
0
50
100
150
200
OUTPUT CURRENT (mA)
_______________________________________________________________________________________
250
300
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
BIAS SUPPLY CURRENT vs. TEMPERATURE
VBIAS = 5V
145
140
IBIAS (µA)
26.5
135
130
26.0
125
25.5
25.0
115
-15
10
35
60
85
150
100
50
0
-15
-40
10
35
60
85
0
100
150
200
250
TEMPERATURE (°C)
OUTPUT CURRENT (mA)
OUTPUT VOLTAGE ERROR
vs. OUTPUT CURRENT
OUTPUT VOLTAGE ERROR vs. TEMPERATURE
SHORT-CIRCUIT CURRENT LIMIT
vs. INPUT VOLTAGE
0.50
0.25
0
-0.25
-0.50
VIN = 1.8V
0.75
0.50
0.25
ILOAD = 300mA
0
-0.25
ILOAD = 200mA
-0.50
ILOAD = 0mA
-0.75
-0.75
800
150
200
250
-40
300
600
500
400
300
200
100
-15
10
35
60
1.50
85
2.50
SHORT-CIRCUIT CURRENT LIMIT
vs. TEMPERATURE
650
4.50
5.50
POWER-SUPPLY REJECTION RATIO (VIN)
vs. FREQUENCY
0
MAX1982/83 toc10
700
3.50
INPUT VOLTAGE (V)
TEMPERATURE (°C)
OUTPUT CURRENT (mA)
MAX1982/83 toc11
100
VIN = 2.1V
VP-P = 0.6V
ILOAD = 0
-10
-20
-30
PSRR (dB)
SHORT-CIRCUIT CURRENT LIMIT (mA)
50
700
0
-1.00
-1.00
300
MAX1982/83 toc09
0.75
1.00
SHORT-CIRCUIT CURRENT LIMIT (mA)
VBIAS = 5V
VIN = 1.8V
RELATIVE VOUT ERROR (%)
1.00
0
50
TEMPERATURE (°C)
MAX1982/83 toc07
-40
VOUT ERROR (%)
VBIAS = 5V
120
MAX1982/83 toc08
IIN (µA)
27.0
DROPOUT VOLTAGE vs. OUTPUT CURRENT
200
MAX1982/83 toc06
VBIAS = 5V
27.5
MAX1982/83 toc05
MAX1982/83 toc04
150
DROPOUT VOLTAGE (mV)
INPUT CURRENT vs. TEMPERATURE
28.0
600
-40
-50
-60
-70
550
-80
-90
500
-100
-40
-15
10
35
TEMPERATURE (°C)
60
85
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
_______________________________________________________________________________________
5
MAX1982/MAX1983
Typical Operating Characteristics (continued)
(Circuit of Figure 3, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(Circuit of Figure 3, TA = +25°C, unless otherwise noted.)
POWER-SUPPLY REJECTION RATIO (VBIAS)
vs. FREQUENCY
0
-20
-40
-40
PSRR (dB)
-30
-50
-60
-70
-80
-90
-90
-100
-100
1k
10k
100k
IL = 200mA
IL = 100mA
-60
-80
100
IL = 300mA
-50
-70
10
VIN = 3V
VP-P = 0.4V
-10
-30
MAX1982/83 toc13
VBIAS = 5V
VP-P = 0.6V
ILOAD = 0
-20
RIPPLE REJECTION RATIO (VIN)
vs. FREQUENCY
MAX1982/83 toc12
0
-10
PSRR (dB)
MAX1982/MAX1983
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
1M
10
FREQUENCY (Hz)
100
1k
10k
100k
1M
FREQUENCY (Hz)
LINE TRANSIENT (NO LOAD)
LOAD TRANSIENT (1mA TO 300mA)
MAX1982/83 toc14
MAX1982/83 toc15
2.4V
VIN
1.8V
500mV/
div
1mV/
div
VOUT
300mA
ILOAD
200mA/
div
10mV/
div
VOUT
1mV/div
100µs/div
10µs/div
LOAD TRANSIENT (300mA TO 1mA)
LOAD TRANSIENT IN DROPOUT
MAX1982/83 toc16
300mA
ILOAD
200mA/
div
10mV/
div
VOUT
10µs/div
6
MAX1982/83 toc17
300mA
ILOAD
200mA/
div
50mV/
div
VOUT
20µs/div
_______________________________________________________________________________________
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
UNDERVOLTAGE LOCKOUT
SHUTDOWN RESPONSE
MAX1982/83 toc18
MAX1982/83 toc19
5V
5V
VBIAS
2V/
div
VSHDN
2V/
div
1.2V
500mV/
div
500mV/
div
VOUT
ILOAD = 300mA
VOUT
ILOAD = 300mA
100µs/div
100µs/div
PGOOD RESPONSE
MAX1982/83 toc20
2V/
div
VOUT
500mV/
div
VPGOOD
1ms/div
_______________________________________________________________________________________
7
MAX1982/MAX1983
Typical Operating Characteristics (continued)
(Circuit of Figure 3, TA = +25°C, unless otherwise noted.)
MAX1982/MAX1983
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
Pin Description
PIN
NAME
FUNCTION
MAX1982
MAX1983
1
1
BIAS
Bias Voltage. Input voltage to the control circuitry. BIAS powers all control blocks and the gate
of the pass transistor. Bypass BIAS to GND with a 0.1µF ceramic capacitor.
2
2
GND
Ground
3
3
SHDN
4
—
PGOOD
Power-Good Output. The open-drain PGOOD output goes high at least 1ms after the output
voltage has attained regulation. PGOOD asserts low 10µs after the output falls by 10%.
—
4
ADJ
Feedback for Adjustable Output. Connect ADJ to the midpoint of a resistor-divider between
OUT and GND for an adjustable output voltage between 0.8V and 2.0V.
5
5
OUT
Regulator Output. Bypass OUT to GND with a 10µF to 22µF low-ESR ceramic capacitor.
6
6
IN
Shutdown Control Input. Drive SHDN low to enter the low-power shutdown state. Connect
SHDN to BIAS for normal operation.
Internal Pass Transistor Input. IN connects to the drain of the internal power switch. Bypass IN
to GND with a 10µF ceramic capacitor.
Detailed Description
The MAX1982/MAX1983 are low-voltage, low-dropout
linear regulators with an external bias supply input (see
Figures 1 and 2). BIAS is powered by a 4.5V to 5.5V
supply that is commonly available in laptop and desktop computers. The 5V bias supply drives the gate of
the internal pass transistor, while a lower voltage input
at the drain of the transistor (IN) is regulated to provide
VOUT. Separating the bias input voltages yields higher
efficiency. These devices are ideal for applications that
require low-voltage outputs from low-voltage inputs.
The MAX1982 delivers 1.2V (±3%) at 300mA from an
input voltage of 1.25V to 5.5V. The MAX1983 delivers
an adjustable output voltage from 0.8V to 2V.
The MAX1982 features an open-drain PGOOD output
that transitions high 1ms after the output reaches regulation. PGOOD goes low within 10µs of the output
falling out of regulation by 120mV.
Both devices feature current- and thermal-limiting circuitry that protect the MAX1982/MAX1983 from damage during fault conditions.
Bias Supply Input
The BIAS input powers the control circuitry and provides the pass transistor gate drive. Power BIAS from a
well-regulated 5V (±10%) supply. Current drawn from
the BIAS supply remains relatively constant with variations in VIN and load current (see the Typical Operating
Characteristics). Bypass BIAS with a 0.1µF or greater
8
capacitor as close to the device as possible. The bias
supply current remains low (250µA) when the
MAX1982/MAX1983 are in dropout.
Power-Supply Input
IN connects to the drain of the internal N-channel
power transistor. IN may be as low as 1.25V, minimizing
power dissipation. Bypass IN with a 10µF or greater
capacitor as close to the device as possible.
Shutdown
The MAX1982/MAX1983 feature a low-power shutdown
mode that reduces quiescent current drawn to 1µA
(typ), and BIAS current consumption to less than 1µA
(typ). Driving SHDN low disables the voltage reference,
error amplifier, gate-drive circuitry, and pass transistor
(see Figure 2), and the device output enters a highimpedance state. Connect SHDN to BIAS for normal
operation.
PGOOD Output
The MAX1982 provides an open-drain PGOOD output
that goes high 1ms (min) after the output attains regulation (within 10% of the nominal output voltage). PGOOD
transitions low 10µs after the output falls out of regulation by 120mV, or when the device enters shutdown.
Connect a pullup resistor from PGOOD to BIAS for a
logic-level output. Use a 100kΩ resistor to minimize
current consumption.
_______________________________________________________________________________________
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
MAX1982/MAX1983
PGOOD
MAX1982
SHDN
1ms
DELAY
BIAS
UVLO
SHUTDOWN
OVERTEMP
IN
CURRENT
SENSE
BIAS
0.8V REFERENCE
OUT
GND
Figure 1. MAX1982 Functional Diagram
MAX1983
SHDN
BIAS
UVLO
SHUTDOWN
OVERTEMP
IN
CURRENT
SENSE
BIAS
0.8V REFERENCE
GM
OUT
AV
R1
ADJ
R2
GND
Figure 2. MAX1983 Functional Diagram
_______________________________________________________________________________________
9
MAX1982/MAX1983
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
Current Limit
The MAX1982/MAX1983 limit the output current to
600mA (typ) in the event of an overload or output short
circuit. The current limit prevents damage to the internal power transistor, but the device can enter thermal
shutdown if the power dissipation is great enough to
increase the die temperature above +160°C (see the
Thermal-Overload Protection section).
Thermal-Overload Protection
Thermal-overload protection limits the power dissipation in the MAX1982/MAX1983. When the die temperature exceeds +160°C, the pass transistor turns off,
allowing the device to cool. Normal operation resumes
when the die temperature cools by 20°C. A continuous
thermal-overload condition results in a pulsed output.
For continuous operation, do not exceed a junction
temperature of +150°C.
Applications Information
Output Voltage Selection
The MAX1982 output is fixed at 1.2V. The MAX1983
provides an adjustable output (0.8V to 2.0V). Connect
ADJ to a resistive voltage-divider between OUT and
4.5V TO 5.5V
1.25V TO 5.5V
IN
BIAS
10µF
0.1µF
MAX1982
GND
1.2V
OUT
10µF
ON
SHDN
PGOOD
OFF
100kΩ
Figure 3. MAX1982 Typical Application Circuit
4.5V TO 5.5V
IN
BIAS
1.5V TO 5.5V
10µF
MAX1983
0.1µF
GND
1.2V
OUT
R1
20kΩ
ON
SHDN
Figure 4. MAX1983 Typical Application Circuit
10
10µF
ADJ
OFF
R2
40kΩ
GND as shown in Figure 4. Set the output voltage using
the following equation:
 R1 
VOUT = 0.8V 1+ 
 R2 
Set R2 at 40kΩ and choose R1 to achieve the desired
output voltage. Set VIN to higher than (VOUT + 400mV)
to meet the dropout voltage requirement (see the
Input/Output (Dropout) Voltage section).
To ensure stability over the specified input voltage
range, the minimum output capacitance must be 10µF
with a maximum ESR of 35mΩ.
Operating Region and Power Dissipation
The maximum power dissipation of the MAX1982/
MAX1983 depends on the thermal resistance of the 6-pin
SOT23 package and the circuit board, the temperature
difference between the die and ambient air, and the rate
of airflow. The power dissipated in the device is:
PD = IOUT × ( VIN − VOUT )
The resulting maximum power dissipation is:
PDISS(MAX) =
TJ(MAX) − TA
θ JC + θCA
where TJ(MAX) is the maximum junction temperature
(+150°C) and TA is the ambient temperature, θJC is the
thermal resistance from the die junction to the package
case, and θCA is the thermal resistance from the case
through the PC board, copper traces, and other materials to the surrounding air. For optimum power dissipation, use a large ground plane with good thermal
contact to GND, and use wide input and output traces.
When 1 square inch of copper is connected to the
device, the maximum allowable power dissipation of a
6-pin SOT23 package is 696mW. The maximum power
dissipation is derated by 8.7mW/°C above TA = +70°C.
Extra copper on the PC board increases thermal mass,
and reduces thermal resistance of the board. Refer to
the MAX1982/MAX1983 EV kit for a layout example.
The MAX1982/MAX1983 deliver up to 300mA and operate with input voltages up to 5.5V, but not simultaneously. High output currents can only be achieved when
the input-output differential voltages are low (Figure 5).
Undervoltage Lockout (UVLO)
The undervoltage lockout (UVLO) circuit ensures that
the regulator starts up with adequate voltage for the
gate-drive circuitry to bias the internal pass transistor.
______________________________________________________________________________________
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
TYPICAL DROPOUT VOLTAGE LIMIT
250
200
150
100
50
TA = +25°C
TYPICAL SUPPLY VOLTAGE LIMIT
MAXIMUM OUTPUT CURRENT (mA)
MAXIMUM CONTINUOUS CURRENT
300
TA = +50°C
TA = +70°C
TJ = +150°C
0
0
1
2
3
4
5
INPUT-OUTPUT DIFFERENTIAL VOLTAGE (V)
Figure 5. Power Operating Region—Maximum Output Current
vs. Supply Voltage
The UVLO circuitry monitors V BIAS only. The UVLO
threshold is 4.2V, and VBIAS must remain above this
level for proper operation, regardless of the level of VIN.
The MAX1982/MAX1983 load-transient response graphs
(see the Typical Operating Characteristics) show two
components of the output response: a DC shift from the
output impedance due to the load current change and
the transient response. A typical transient response for a
step change in the load current from 1mA to 300mA is
20mV. Increasing the output capacitor’s value and
decreasing the ESR attenuate the overshoot.
Input/Output (Dropout) Voltage
A regulator’s minimum input-to-output voltage differential (dropout voltage) determines the lowest usable supply voltage. In battery-powered systems, the dropout
voltage determines the useful end-of-life battery voltage. Because the MAX1982/MAX1983 use an N-channel pass transistor, the dropout voltage is a function of
the drain-to-source on-resistance (RDS(ON) = 1Ω max)
multiplied by the load current (see the Typical
Operating Characteristics):
VDROPOUT = VIN − VOUT = RDS(ON) × IOUT
Input Capacitor
PC Board Layout Guidelines
Bypass IN to ground with a 10µF or greater ceramic
capacitor. Bypass BIAS to ground with a 0.1µF ceramic
capacitor for normal operation in most applications.
The MAX1982/MAX1983 require proper layout to
achieve the intended output power level, high efficiency,
and low noise. Proper layout involves the use of a
ground plane, appropriate component placement, and
correct routing of traces using appropriate trace widths.
Output Capacitor
Bypass OUT to ground with a low-ESR ceramic capacitor greater than 10µF. The ESR must be less than
35mΩ. Choose an output capacitor to maintain the
required output voltage tolerance during a load step.
The change in output voltage is,

∆t 
∆V = I ESR +

COUT 

where I is the load current, COUT is the output capacitance, and ∆t is the duration of the load step.
Noise, PSRR, and Transient Response
The MAX1982/MAX1983 operate with low-dropout voltage and low quiescent current in notebook computers
while maintaining good noise, transient response, and
AC rejection specifications. See the Typical Operating
Characteristics for a graph of Power-Supply Rejection
Ratio (PSRR) vs. Frequency. Improved supply-noise
rejection and transient response can be achieved by
increasing the values of the input and output capacitors
and use passive filtering techniques when operating
from noisy sources.
1) Minimize high-current ground loops. Connect the
ground of the device, the input capacitor, and the
output capacitor together at one point.
2) To optimize performance, a ground plane is essential. Use all available copper layers in applications
where the device is located on a multilayer board.
3) Connect the input filter capacitor less than 10mm
from IN. The connecting copper trace carries large
currents and must be at least 2mm wide, preferably
5mm wide.
4) Use as much copper as necessary to increase the
thermal resistance of the device. In general, more
copper provides better heatsinking capabilities.
Chip Information
TRANSISTOR COUNT: 430
PROCESS: BiCMOS
______________________________________________________________________________________
11
MAX1982/MAX1983
350
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
6LSOT.EPS
MAX1982/MAX1983
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2002 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Similar pages