TI BQ4822YMA-70 Rtc module with 8kx8 nvsram Datasheet

bq4822Y
RTC Module With 8Kx8 NVSRAM
Features
General Description
➤ Integrated SRAM, real-time
clock, CPU supervisor, crystal,
power-fail circuit, and battery
The bq4822Y RTC Module is a nonvolatile 65,536-bit SRAM organized
as 8192 words by 8 bits with an integral real-time clock and CPU supervisor. The CPU supervisor provides a programmable watchdog
timer and a microprocessor reset.
Other features include an alarm,
power-fail and periodic interrupt,
and a battery low warning.
➤ Real-Time Clock counts hundredths of seconds through years
in BCD format
➤ RAM-like clock access
➤ Compatible with industrystandard 8K x 8 SRAMs
The device combines an internal
lithium battery, quartz crystal, clock
and power-fail chip, and a full
CMOS SRAM in a plastic 28-pin
DIP module. The RTC Module directly replaces industry-standard
SRAMs and also fits into many
EPR O M a n d E E P R O M s o ck e ts
without any requirement for special
write timing or limitations on the
number of write cycles.
➤ Unlimited write cycles
➤ 10-year minimum data retention
and clock operation in the absence of power
➤ Automatic power-fail chip deselect and write-protection
➤ Watchdog timer, power-on reset,
alarm/periodic interrupt, powerfail and battery-low warning
Registers for the real-time clock,
alarm and other special functi o n s a re l o ca te d i n re g i s ters
1FF0h–1FFFh of the memory array.
The clock and alarm registers are
dual-port read/write SRAM locations that are updated once per second by a clock control circuit from
the internal clock counters. The
dual-port registers allow clock updates to occur without interrupting
normal access to the rest of the
SRAM array.
The bq4822Y also contains a powerfail-detect circuit. The circuit deselects the device whenever VCC falls
below tolerance, providing a high degree of data security. The battery is
electrically isolated when shipped
from the factory to provide maximum battery capacity. The battery
remains disconnected until the first
application of VCC.
➤ Automatic leap year adjustment
➤ Software clock calibration for
greater than ±1 minute per
month accuracy
Pin Names
Pin Connections
RST
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VCC
WE
INT
A8
A9
A11
OE
A10
CE
DQ7
DQ6
DQ5
DQ4
DQ3
28-Pin DIP Module
PN482201.eps
May 1997
1
A0–A12
Address input
CE
Chip enable
RST
Microprocessor reset
WE
Write enable
OE
Output enable
DQ0–DQ7
Data in/data out
INT
Programmable interrupt
VCC
+5 volts
VSS
Ground
bq4822Y
Functional Description
including memory and clock interface, data-retention
modes, power-on reset timing, watchdog timer activation, and interrupt generation.
Figure 1 is a block diagram of the bq4822Y. The following sections describe the bq4822Y functional operation,
TimeBase
Oscillator
Internal
Quartz
Crystal
÷8
÷ 64
÷ 64
16 : 1 MUX
Control/Status
Registers
CE
RST
Reset and
Interupt
Generator
OE
DQ0–DQ7
Clock/Calendar, Alarm
and Control Bytes
P
Bus
I/F
AD0–AD14
Storage Registers
(16 Bytes)
WE
VCC
PowerFail
Control
Internal
Battery
INT
Control/Calendar
Update
Storage Registers
(8,176 Bytes)
Write
Protect
BD482201.eps
Figure 1. Block Diagram
Truth Table
VCC
CE
OE
WE
Mode
DQ
Power
< VCC (max.)
VIH
X
X
Deselect
High Z
Standby
VIL
X
VIL
Write
DIN
Active
VIL
VIL
VIH
Read
DOUT
Active
VIL
VIH
VIH
Read
High Z
Active
< VPFD (min.) > VSO
X
X
X
Deselect
High Z
CMOS standby
≤ VSO
X
X
X
Deselect
High Z
Battery-backup mode
> VCC (min.)
May 1997
2
bq4822Y
CE and OE control the state of the eight three--state data
I/O signals. If the outputs are activated before tAA, the data
lines are driven to an indeterminate state until tAA. If the
address inputs are changed while CE and OE remain low,
output data remains valid for tOH (output data hold time),
but goes indeterminate until the next address access.
Address Map
The bq4822Y provides 16 bytes of clock and control
status registers and 8,176 bytes of storage RAM.
Figure 2 illustrates the address map for the bq4822Y.
Table 1 is a map of the bq4822Y registers, and Table 2
describes the register bits.
Write Mode
The bq4822Y is in write mode whenever WE and CE are
active. The start of a write is referenced from the
latter--occurring falling edge of WE or CE. A write is
terminated by the earlier rising edge of WE or CE. The
addresses must be held valid throughout the cycle. CE
or WE must return high for a minimum of tWR2 from
CE or tWR1 from WE prior to the initiation of another
read or write cycle.
Memory Interface
Read Mode
The bq4822Y is in read mode whenever OE (output enable) is low and CE (chip enable) is low. The device architecture allows ripple-through access of data from
eight of 65,536 locations in the static storage array.
Thus, the unique address specified by the 13 address inputs defines which one of the 8,192 bytes of data is to be
accessed. Valid data is available at the data I/O pins
within tAA (address access time) after the last address
input signal is stable, providing that the CE and OE
(output enable) access times are also satisfied. If the CE
and OE access times are not met, valid data is available
after the latter of chip enable access time (tACE) or output enable access time (tOE).
16 Bytes
Clock and
Control Status
Registers
Data-in must be valid tDW prior to the end of write and
remain valid for tDH1 or tDH2 afterward. OE should be
kept high during write cycles to avoid bus contention; although, if the output bus has been activated by a low on
CE and OE, a low on WE disables the outputs tWZ after
WE falls.
1FFF
1FF0
0
1
2
3
4
5
6
7
8
9
1FEF
8,176
Bytes
Storage
RAM
10
11
12
13
14
15
0000
Year
Month
Date
Days
Hours
Minutes
Seconds
Control
Watchdog
1FFF
1FFE
1FFD
1FFC
1FFB
1FFA
1FF9
1FF8
1FF7
Interrupts
Alarm Date
Alarm Hours
1FF6
1FF5
1FF4
Alarm Minutes 1FF3
Alarm Seconds 1FF2
Tenths/
1FF1
Hundredths
Flags
1FF0
FG482201.eps
Figure 2. Address Map
May 1997
3
bq4822Y
Data-Retention Mode
Clock Interface
With valid V CC applied, the bq4822Y operates as a
conventional static RAM. Should the supply voltage
decay, the RAM automatically power-fail deselects,
write-protecting itself tWPT after VCC falls below VPFD.
All outputs become high impedance, and all inputs are
treated as “don't care.”
Reading the Clock
The interface to the clock and control registers of the
bq4822Y is the same as that for the general-purpose
storage memory. Once every second, the user-accessible
clock/calendar locations are updated simultaneously
from the internal real time counters. To prevent reading data in transition, updates to the bq4822Y clock registers should be halted. Updating is halted by setting
the read bit D6 of the control register to 1. As long as
the read bit is 1, updates to user-accessible clock locations are inhibited. Once the frozen clock information is
retrieved by reading the appropriate clock memory locations, the read bit should be reset to 0 in order to allow
updates to occur from the internal counters. Because the
internal counters are not halted by setting the read bit,
reading the clock locations has no effect on clock accuracy. Once the read bit is reset to 0, within one second
the internal registers update the user-accessible registers with the correct time. A halt command issued during a clock update allows the update to occur before
freezing the data.
If power-fail detection occurs during a valid access, the
memory cycle continues to completion. If the memory
cycle fails to terminate within time t WPT, writeprotection takes place. When VCC drops below VSO, the
control circuit switches power to the internal energy
source, which preserves data.
The internal coin cell maintains data in the bq4822Y after the initial application of VCC for an accumulated period of at least 10 years when VCC is less than VSO. As
system power returns and Vcc rises above VSO, the battery is disconnected, and the power supply is switched to
external VCC. Write-protection continues for tCER after
VCC reaches VPFD to allow for processor stabilization.
After tCER, normal RAM operation can resume.
Table 1. bq4822Y Clock and Control Register Map
Address
D7
D6
1FFF
D5
D4
D3
D2
10 Years
D1
D0
Year
10 Month
00–99
Register
Year
1FFE
X
X
1FFD
X
X
1FFC
X
FTE
1FFB
X
X
1FFA
X
1FF9
OSC
1FF8
W
R
S
1FF7
WDS
BM4
BM3
BM2
BM1
1FF6
AIE
PWRIE
ABE
PIE
RS3
1FF5
ALM3
X
10-date alarm
Alarm date
01–31
1FF4
ALM2
X
10-hour alarm
Alarm hours
00–23
Alarm hours
1FF3
ALM1
Alarm 10 minutes
Alarm minutes
00–59
Alarm minutes
1FF2
ALM0
Alarm 10 seconds
Alarm seconds
00–59
Alarm seconds
1FF1
X
Range (h)
Month
01–12
Month
Date
01–31
Date
10 Date
X
X
X
01–07
Days
Hours
Day
00–23
Hours
10 Minutes
Minutes
00–59
Minutes
10 Seconds
Seconds
00–59
Seconds
10 Hours
Calibration
0.1 seconds
AF
PWRF
00–31
BM0
WD1
WD0
RS2
RS1
RS0
0.01 seconds
1FF0
WDF
BLF
PF
Notes:
X = Unused bits; can be written and read.
Clock/Calendar data in 24-hour BCD format.
BLF = 1 for low battery.
OSC = 1 stops the clock oscillator.
Interrupt enables are cleared on power-up.
X
X
Interrupts
00–99
X
Control
Watchdog
Alarm date
0.1/0.01 seconds
Flags
May 1997
4
bq4822Y
Calibrating the Clock
Table 2. Clock and Control Register Bits
Bits
The bq4822Y real-time clock is driven by a quartz controlled oscillator with a nominal frequency of 32,768 Hz.
The quartz crystal is contained within the bq4822Y
package along with the battery. The clock accuracy of
the bq4822Y module is tested to be within 20ppm or
about 1 minute per month at 25°C. The oscillation rates
of crystals change with temperature as Figure 3 shows.
To compensate for the frequency shift, the bq4822Y offers onboard software clock calibration. The user can
adjust the calibration based on the typical operating
temperature of individual applications.
Description
ABE
Alarm interrupt enable in
battery-backup mode
AF
Alarm interrupt flag
AIE
Alarm interrupt enable
ALM0–ALM3
Alarm repeat rate
BLF
Battery-low flag
BM0–BM4
Watchdog multiplier
FTE
Frequency test mode enable
OSC
Oscillator stop
PF
Periodic interrupt flag
PIE
Periodic interrupt enable
PWRF
Power-fail interrupt flag
PWRIE
Power-fail interrupt enable
R
Read clock enable
RS0–RS3
Periodic interrupt rate
S
Calibration sign
W
Write clock enable
WD0–WD1
Watchdog resolution
WDF
Watchdog flag
WDS
Watchdog steering
The software calibration bits are located in the control
register. Bits D0–D4 control the magnitude of correction, and bit D5 the direction (positive or negative) of
correction. Assuming that the oscillator is running at
exactly 32,786 Hz, each calibration step of D0–D4 adjusts the clock rate by +4.068 ppm (+10.7 seconds per
month) or -2.034 ppm (-5.35 seconds per month) depending on the value of the sign bit D5. When the sign bit is
1, positive adjustment occurs; a 0 activates negative adjustment. The total range of clock calibration is +5.5 or
-2.75 minutes per month.
Two methods can be used to ascertain how much calibration a given bq4822Y may require in a system. The
first involves simply setting the clock, letting it run for a
month, and then comparing the time to an accurate
known reference like WWV radio broadcasts. Based on
the variation to the standard, the end user can adjust
the clock to match the system's environment even after
the product is packaged in a non-serviceable enclosure.
The only requirement is a utility that allows the end
user to access the calibration bits in the control register.
Setting the Clock
Bit D7 of the control register is the write bit. Like the
read bit, the write bit when set to a 1 halts updates to
the clock/calendar memory locations. Once frozen, the
locations can be written with the desired information in
24-hour BCD format. Resetting the write bit to 0 causes
the written values to be transferred to the internal clock
counters and allows updates to the user-accessible registers to resume within one second.
0
Frequency Error
-20
Stopping and Starting the Clock Oscillator
-40
-60
-80
-100
The OSC bit in the seconds register turns the clock on or
off. If the bq4822Y is to spend a significant period of
time in storage, the clock oscillator can be turned off to
preserve battery capacity. OSC set to 1 stops the clock
oscillator. When OSC is reset to 0, the clock oscillator is
turned on and clock updates to user-accessible memory
locations occur within one second.
-120
-30 -20 -10 0 10 20 30 40 50 60 70
Temperature ( C)
GR482201
Figure 3. Frequency Error
The OSC bit is set to 1 when shipped from the Benchmarq factory.
May 1997
5
bq4822Y
ally, when the watchdog times out, the watchdog flag bit
(WDF) in the flags register, location 1FF0, is set.
The second approach uses a bq4822Y test mode. When
the frequency test mode enable bit FTE in the days register is set to a 1, and the oscillator is running at exactly
32,768 Hz, the LSB of the seconds register toggles at 512
Hz. Any deviation from 512 Hz indicates the degree and
direction of oscillator frequency shift at the test temperature. For example, a reading of 512.01024 Hz indicates a (1E6*0.01024)/512 or +20 ppm oscillator frequency error, requiring ten steps of negative calibration
(10*-2.034 or -20.34) or 001010 to be loaded into the calibration byte for correction. To read the test frequency,
the bq4822Y must be selected and held in an extended
read of the seconds register, location 1FF9, without having the read bit set. The frequency appears on DQ0.
The FTE bit must be set using the write bit control. The
FTE bit must be reset to 0 for normal clock operation to
resume.
To reset the watchdog timer, the microprocessor must
write to the watchdog register. After being reset by a
write, the watchdog time-out period starts over. As a
precaution, the watchdog circuit is disabled on a power
failure. The user must, therefore, set the watchdog at
boot-up for activation.
Interrupts
The bq4822Y allows four individually selected interrupt
events to generate an interrupt request on the INT pin.
These four interrupt events are:
n The watchdog timer interrupt, programmable to
occur according to the time-out period and conditions
described in the watchdog timer section.
Power-On Reset
n The periodic interrupt, programmable to occur once
every 122µs to 500ms.
The bq4822Y provides a power-on reset, which pulls the
RST pin low on power-down and remains low on powerup for tCER after VCC passes VPFD.
n The alarm interrupt, programmable to occur once per
second to once per month.
Watchdog Timer
n The power-fail interrupt, which can be enabled to be
asserted when the bq4822Y detects a power failure.
The watchdog circuit monitors the microprocessor's activity. If the processor does not reset the watchdog timer
within the programmed time-out period, the circuit asserts the INT or RST pin. The watchdog timer is activated by writing the desired time-out period into the
eight-bit watchdog register described in Table 3 (device
address 1FF7). The five bits (BM4–BM0) store a binary
multiplier, and the two lower-order bits (WD1–WD0) select the resolution, where 00 = 1 16 second, 01 = 1 4 second,
10 = 1 second, and 11 = 4 seconds.
The periodic, alarm, and power-fail interrupts are enabled by an individual interrupt-enable bit in register
1FF6, the interrupts register. When an event occurs, its
event flag bit in the flags register, location 1FF0, is set.
If the corresponding event enable bit is also set, then an
interrupt request is generated. Reading the flags register clears all flag bits and makes INT high impedance.
To reset the flag register, the bq4822Y addresses must
be held stable at location 1FF0 for at least 50ns to avoid
inadvertent resets.
The time-out period is the multiplication of the five-bit
multiplier with the two-bit resolution. For example,
writing 00011 in BM4–BM0 and 10 in WD1–WD0 results in a total time-out setting of 3 x 1 or 3 seconds. A
multiplier of zero disables the watchdog circuit. Bit 7 of
the watchdog register (WDS) is the watchdog steering
bit. When WDS is set to a 1 and a time-out occurs, the
watchdog asserts a reset pulse for tCER on the RST pin.
During the reset pulse, the watchdog register is cleared
to all zeros disabling the watchdog. When WDS is set to
a 0, the watchdog asserts the INT pin on a time-out.
The INT pin remains low until the watchdog is reset by
the microprocessor or a power failure occurs. Addition-
Periodic Interrupt
Bits RS3–RS0 in the interrupts register program the
rate for the periodic interrupt. The user can interpret
the interrupt in two ways: either by polling the flags
register for PF assertion or by setting PIE so that INT
goes active when the bq4822Y sets the periodic flag.
Reading the flags register resets the PF bit and returns
INT to the high-impedance state. Table 4 shows the
periodic rates.
Table 3. Watchdog Register Bits
MSB
Bits
LSB
7
6
5
4
3
2
1
0
WDS
BM4
BM3
BM2
BM1
BM0
WD1
WD0
May 1997
6
bq4822Y
Table 5. Alarm Frequency
(Alarm Bits DQ7 of Alarm Registers)
Table 4. Periodic Rates
RS3
RS2
RS1
RS0
Interrupt
Rate
ALM3
ALM2
ALM1
ALM0
1
1
1
1
Once per second
Alarm Frequency
1
1
1
0
Once per minute
when seconds match
1
1
0
0
Once per hour when
minutes, and seconds
match
1
0
0
0
Once per day when
hours, minutes, and
seconds match
0
0
0
0
When date, hours,
minutes, and seconds
match
0
0
0
0
None
0
0
0
1
10ms
0
0
1
0
100ms
0
0
1
1
122.07µs
0
1
0
0
244.14µs
0
1
0
1
488.281µs
0
1
1
0
976.5625
0
1
1
1
1.953125ms
1
0
0
0
3.90625ms
1
0
0
1
7.8125ms
1
0
1
0
15.625ms
1
0
1
1
31.25ms
1
1
0
0
62.5ms
1
1
0
1
125ms
1
1
1
0
250ms
Power-Fail Interrupt
1
1
1
1
500ms
When V CC falls to the power-fail-detect point, the
power-fail flag PWRF is set. If the power-fail interrupt
enable bit (PWRIE) is also set, then INT is asserted low.
The power-fail interrupt occurs tWPT before the bq4822Y
generates a reset and deselects. The PWRIE bit is
cleared on power-up.
The alarm interrupt can be made active while the
bq4822Y is in the battery-backup mode by setting ABE
in the interrupts register. Normally, the INT pin tristates during battery backup. With ABE set, however,
INT is driven low if an alarm condition occurs and the
AIE bit is set. Because the AIE bit is reset during
power-on reset, an alarm generated during power-on reset updates only the flags register. The user can read
the flags register during boot-up to determine if an
alarm was generated during power-on reset.
Alarm Interrupt
Registers 1FF5–1FF2 program the real-time clock
alarm. During each update cycle, the bq4822Y compares
the date, hours, minutes, and seconds in the clock registers with the corresponding alarm registers. If a match
between all the corresponding bytes is found, the alarm
flag AF in the flags register is set. If the alarm interrupt is enabled with AIE, an interrupt request is generated on INT. The alarm condition is cleared by a read to
the flags register. ALM3–ALM0 puts the alarm into a
periodic mode of operation. Table 5 describes the selectable rates.
Battery-Low Warning
The bq4822Y checks the internal battery on power-up.
If the battery voltage is below 2.2V, the battery-low flag
BLF in the flags register is set to a 1 indicating that
clock and RAM data may be invalid.
May 1997
7
bq4822Y
Absolute Maximum Ratings
Symbol
Parameter
Value
Unit
VCC
DC voltage applied on VCC relative to VSS
-0.3 to 7.0
V
VT
DC voltage applied on any pin excluding VCC
relative to VSS
-0.3 to 7.0
V
TOPR
Operating temperature
0 to +70
°C
TSTG
Storage temperature (VCC off; oscillator off)
-40 to +70
°C
TBIAS
Temperature under bias
-10 to +70
°C
TSOLDER
Soldering temperature
+260
°C
Note:
Conditions
VT ≤ VCC + 0.3
For 10 seconds
Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation
should be limited to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to conditions beyond the operational limits for extended periods of time may affect device reliability.
Recommended DC Operating Conditions (TA = TOPR)
Symbol
Note:
Parameter
Minimum
Typical
Maximum
Unit
VCC
Supply voltage
4.5
5.0
5.5
V
VSS
Supply voltage
0
0
0
V
VIL
Input low voltage
-0.3
-
0.8
V
VIH
Input high voltage
2.2
-
VCC + 0.3
V
Notes
Typical values indicate operation at TA = 25°C.
May 1997
8
bq4822Y
DC Electrical Characteristics (TA = TOPR, VCCMIN
Symbol
Parameter
≤ VCC ≤ VCCMAX)
Minimum
Typical
Maximum
Unit
Conditions/Notes
ILI
Input leakage current
-
-
±1
µA
VIN = VSS to VCC
ILO
Output leakage current
-
-
±1
µA
CE = VIH or OE = VIH or
WE = VIL
VOH
Output high voltage
2.4
-
-
V
IOH = -1.0 mA
VOL
Output low voltage
-
-
0.4
V
IOL = 2.1 mA
IOD
RST, INT sink current
10
-
-
mA
VOL = 0.4V
ISB1
Standby supply current
-
3
6
mA
CE = VIH
ISB2
Standby supply current
-
2
4
mA
CE ≥ VCC - 0.2V,
0V ≤ VIN ≤ 0.2V,
or VIN ≥ VCC - 0.2V
ICC
Operating supply current
-
55
75
mA
Min. cycle, duty = 100%,
CE = VIL, II/O = 0mA
VPFD
Power-fail-detect voltage
4.30
4.37
4.50
V
VSO
Supply switch-over voltage
-
3
-
V
Notes:
Typical values indicate operation at TA = 25°C, VCC = 5V.
RST and INT are open-drain outputs.
Capacitance (TA = 25°C, F = 1MHz, VCC = 5.0V)
Symbol
Parameter
Minimum
Typical
Maximum
Unit
Conditions
CI/O
Input/output capacitance
-
-
10
pF
Output voltage = 0V
CIN
Input capacitance
-
-
10
pF
Input voltage = 0V
Note:
These parameters are sampled and not 100% tested.
May 1997
9
bq4822Y
AC Test Conditions
Parameter
Test Conditions
Input pulse levels
0V to 3.0V
Input rise and fall times
5 ns
Input and output timing reference levels
1.5 V (unless otherwise specified)
Output load (including scope and jig)
See Figures 4 and 5
+5V
+5V
1.9k
1.9kΩ
DOUT
DOUT
1k
100pF
1kΩ
FG482202.eps
FG482203.eps
Figure 4. Output Load A
Read Cycle
5pF
Figure 5. Output Load B
(TA = TOPR, VCCMIN ≤ VCC ≤ VCCMAX)
–70
Symbol
Parameter
Min.
Max.
Unit
70
-
ns
Conditions
tRC
Read cycle time
tAA
Address access time
-
70
ns
Output load A
tACE
Chip enable access time
-
70
ns
Output load A
tOE
Output enable to output valid
-
35
ns
Output load A
tCLZ
Chip enable to output in low Z
5
-
ns
Output load B
tOLZ
Output enable to output in low Z
5
-
ns
Output load B
tCHZ
Chip disable to output in high Z
0
25
ns
Output load B
tOHZ
Output disable to output in high Z
0
25
ns
Output load B
tOH
Output hold from address change
10
-
ns
Output load A
May 1997
10
bq4822Y
Read Cycle No. 1 (Address Access) 1,2
tRC
Address
tAA
tOH
DOUT
Previous Data Valid
Data Valid
TD482201.eps
Read Cycle No. 2 (CE Access) 1,3,4
tRC
CE
tACE
tCLZ
DOUT
tCHZ
High-Z
High-Z
Read Cycle No. 3 (OE Access) 1,5
TD482202.eps
tRC
Address
tAA
OE
tOE
tOHZ
tOLZ
DOUT
Data Valid
High-Z
High-Z
TD482203.eps
Notes:
1. WE is held high for a read cycle.
2. Device is continuously selected: CE = OE = VIL.
3. Address is valid prior to or coincident with CE transition low.
4. OE = VIL.
5. Device is continuously selected: CE = VIL.
May 1997
11
bq4822Y
Write Cycle
(TA =TOPR , VCCMIN ≤ VCC ≤ VCCMAX)
–70
Symbol
Parameter
Min.
Max.
Units
Conditions/Notes
tWC
Write cycle time
70
-
ns
tCW
Chip enable to end of write
55
-
ns
(1)
tAW
Address valid to end of write
60
-
ns
(1)
tAS
Address setup time
0
-
ns
Measured from address valid to beginning of write. (2)
tWP
Write pulse width
50
-
ns
Measured from beginning of write
to end of write. (1)
tWR1
Write recovery time (write cycle 1)
0
-
ns
Measured from WE going high to
end of write cycle. (3)
tWR2
Write recovery time (write cycle 2)
0
-
ns
Measured from CE going high to
end of write cycle. (3)
tDW
Data valid to end of write
30
-
ns
Measured to first low-to-high transition of either CE or WE.
tDH1
Data hold time (write cycle 1)
5
-
ns
Measured from WE going high to
end of write cycle. (4)
tDH2
Data hold time (write cycle 2)
5
-
ns
Measured from CE going high to
end of write cycle. (4)
tWZ
Write enabled to output in high Z
0
25
ns
I/O pins are in output state. (5)
tOW
Output active from end of write
5
-
ns
I/O pins are in output state. (5)
Notes:
1. A write ends at the earlier transition of CE going high and WE going high.
2. A write occurs during the overlap of a low CE and a low WE. A write begins at the later transition
of CE going low and WE going low.
3. Either tWR1 or tWR2 must be met.
4. Either tDH1 or tDH2 must be met.
5. If CE goes low simultaneously with WE going low or after WE going low, the outputs remain in
high-impedance state.
May 1997
12
bq4822Y
Write Cycle No. 1 (WE-Controlled) 1,2,3
tWC
Address
tAW
tWR2
tCW
CE
tWP
tAS
WE
tDW
DIN
tDH2
Data-in Valid
tOW
tWZ
Data Undefined (2)
DOUT
High-Z
TD482204.eps
Write Cycle No. 2 (CE-Controlled) 1,2,3,4,5
tWC
Address
tAW
tCW
tAS
tWR2
CE
tWP
WE
tDW
DIN
tDH2
Data-in Valid
tWZ
DOUT
Data Undefined (2)
High-Z
TD482205.eps
Notes:
1. CE or WE must be high during address transition.
2. Because I/O may be active (OE low) during this period, data input signals of opposite polarity to the
outputs must not be applied.
3. If OE is high, the I/O pins remain in a state of high impedance.
4. Either tWR1 or tWR2 must be met.
5. Either tDH1 or tDH2 must be met.
May 1997
13
bq4822Y
Power-Down/Power-Up Cycle (TA = TOPR)
Minimum
Typical
Maximum
Unit
tPF
Symbol
VCC slew, 4.50 to 4.20 V
300
-
-
µs
tFS
VCC slew, 4.20 to VSO
10
-
-
µs
tPU
VCC slew, VSO to VPFD
(max.)
0
-
-
µs
tCER
Chip enable recovery time
40
100
200
ms
tDR
Data-retention time in
absence of VCC
10
-
-
years
tWPT
Notes:
Parameter
Write-protect time
40
100
160
µs
Conditions
Time during which SRAM is
write-protected after VCC
passes VFPD on power-up.
TA = 25°C. (2)
Delay after VCC slews down
past VPFD before SRAM is
write-protected.
1. Typical values indicate operation at TA = 25°C, VCC = 5V.
2. Battery is disconnected from circuit until after VCC is applied for the first time. tDR is the
accumulated time in absence of power beginning when power is first applied to the device.
Caution: Negative undershoots below the absolute maximum rating of -0.3V in battery-backup mode
may affect data integrity.
Power-Down/Power-Up Timing
tPF
4.50
VPFD
VPFD
VCC
4.20
VSO
tFS
tWPT
VSO
tPU
tDR
tCER
CE
High-Z
All Outputs Valid (per Control Inputs)
Valid (per Control Inputs)
RST
INT
High-Z
TD482206 .eps
Notes:
1. PWRIE is set to “1” to enable power fail interrupt.
2. RST and INT are open drain and require an external pull-up resistor.
May 1997
14
bq4822Y
MA: 28-Pin A-Type Module
28-Pin MA (A-Type Module)
Inches
Dimension
Min.
Max.
A
0.365
0.375
9.27
9.53
0.015
-
0.38
-
B
0.017
0.023
0.43
0.58
C
0.008
0.013
0.20
0.33
D
1.470
1.500
37.34
38.10
E
0.710
0.740
18.03
18.80
e
0.590
0.630
14.99
16.00
G
0.090
0.110
2.29
2.79
L
0.120
0.150
3.05
3.81
S
0.075
0.110
1.91
2.79
bq4822Y MA Speed Options:
70 = 70 ns
Package Option:
MA = A-type module
Device:
bq4822Y 8K x 8 Real-Time Clock Module
15
Max.
A1
Ordering Information
May 1997
Millimeters
Min.
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated
Similar pages