Hittite HMC403S8G Hbt digital phase-frequency detector, dc - 1.3 ghz Datasheet

MICROWAVE CORPORATION
HMC403S8G
v01.0703
HBT DIGITAL PHASE-FREQUENCY
DETECTOR, DC - 1.3 GHz
10
Typical Applications
Features
This Phase Frequency Detector is a key
component in low phase noise frequency
synthesis applications such as:
1.3 GHz Operation
Low SSB Phase Noise Floor:
-135 dBc/Hz at 100 KHz Offset
• VSAT
Differential Input/Single Ended Output
• Pt-Pt and Pt-MPt Radios
Output Buffer Amplifiers
• LMDS
8-Lead SOIC SMT Package
FREQ. DIVIDER & DETECTORS - SMT
• Sonnet
Functional Diagram
General Description
The HMC403S8G is a digital phase-frequency
detector intended for use in low noise phaselocked loop applications. Its combination of high
frequency of operation along with its low phase
noise floor make possible synthesizers with wide
loop bandwidth and low N resulting in fast switching and very low phase noise. When used in
conjunction with a differential loop amplifier, the
HMC403S8G generates an output voltage that
can be used to phase lock a VCO to a reference
oscillator. The device is available in a small outline 8-lead SOIC plastic package.
Electrical Specifications, TA = +25° C, Vcc = 5V
Parameter
Conditions
Maximum Input Frequency
Sine Wave Input [1]
Input Power Range
Fin = 0.1 to 1.3 GHz
SSB Phase Noise
Typ.
Max.
1.3
Minimum Input Frequency
Output Voltage
Min.
GHz
-10
0.1
GHz
+10
dBm
| ZLoad | ≥ 1k Ω
740
mV,
Pk - Pk
@ 100 kHz Offset
with 800 MHz Input
-135
dBc/Hz
86
mA
Supply Current
1. Detector will operate down to DC for square-wave input signal.
10 - 66
Units
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
MICROWAVE CORPORATION
HMC403S8G
v01.0703
HBT DIGITAL PHASE-FREQUENCY
DETECTOR, DC - 1.3 GHz
Error Voltage vs. Phase Difference,
Pin= 0 dBm, T= 25 °C *
Error Voltage vs. Phase Difference,
Pin= 0 dBm, Fin= 800 MHz *
0.6
250MHz
+25 C
0.4
800MHz
1.3GHz
ERROR VOLTAGE (Vdc)
ERROR VOLTAGE (Vdc)
0.4
0.2
0
-0.2
-0.4
+85 C
-40 C
0.2
10
0
-0.2
-0.4
-0.6
-0.6
−π
−π/2
0
PHASE DIFFERENCE (rad)
π/2
π
−π
−π/2
0
π/2
PHASE DIFFERENCE (rad)
Test Circuit:
* Error Voltage data taken using test circuit above. Loop filter gain has been subtracted from the result.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
π
FREQ. DIVIDERS & DETECTORS - SMT
0.6
10 - 67
HMC403S8G
v01.0703
MICROWAVE CORPORATION
HBT DIGITAL PHASE-FREQUENCY
DETECTOR, DC - 1.3 GHz
10 - 68
SSB Phase Noise Performance,
Pin= 0 dBm, Fin= 800 MHz
250 MHz
800 MHz
1.3 GHz
10
3
10
4
10
5
SSB PHASE NOISE (dBc/Hz)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
-150
-160
2
10
10
6
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
-150
-160
2
10
+25 C
+85 C
-40 C
10
OFFSET FREQUENCY (Hz)
3
10
4
10
5
10
6
OFFSET FREQUENCY (Hz)
Supply Current vs. Supply Voltage
100
95
SUPPLY CURRENT (mA)
FREQ. DIVIDER & DETECTORS - SMT
10
SSB PHASE NOISE (dBc/Hz)
SSB Phase Noise Performance,
Pin= 0 dBm, T= 25 °C
90
85
80
75
+25 C
70
+85 C
-40 C
65
60
4.75
5.00
5.25
SUPPLY VOLTAGE (Vdc)
Typical DC Characteristics
-40C
Symbol
+25C
+85C
Characteristics
Unit
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
Icc
Power Supply
Current
75
85
92
79
86
92
79
86
92
mA
Voh
Output High
Voltage
1.652
1.867
2.086
1.761
1.981
2.214
1.955
2.19
2.411
V
Vol
Output Low
Voltage
1.012
1.107
1.286
1.081
1.241
1.414
1.275
1.45
1.631
V
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
MICROWAVE CORPORATION
HMC403S8G
v01.0703
HBT DIGITAL PHASE-FREQUENCY
DETECTOR, DC - 1.3 GHz
Absolute Maximum Ratings
RF Input (Vcc = +5V)
+13 dBm
Vcc
+5.5V
Surge Current
(Pins ND & NU)
4 mA
DC Current
(Pins ND & NU)
2 mA
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
Outline Drawing
FREQ. DIVIDERS & DETECTORS - SMT
10
NOTES:
1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED
PLASTIC SILICA AND SILICON IMPREGNATED.
2. LEADFRAME MATERIAL: COPPER ALLOY
3. LEADFRAME PLATING: Sn/Pb SOLDER
4. DIMENSIONS ARE IN INCHES [MILLIMETERS].
5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE.
6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE.
7. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED
TO PCB RF GROUND.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
10 - 69
MICROWAVE CORPORATION
HMC403S8G
v01.0703
HBT DIGITAL PHASE-FREQUENCY
DETECTOR, DC - 1.3 GHz
Pin Description
FREQ. DIVIDER & DETECTORS - SMT
10
10 - 70
Pin Number
Function
Description
1
R
Reference input.
2
NR
Reference input complement.
3
V
VCO input.
4
NV
VCO input complement.
5
GND
Ground: Backside of package has exposed metal ground slug which
must be connected to ground.
6
ND
Down output complement
(Device will be permanently damaged if pin is instantaneously shorted to
ground. A minimum load impedance magnitude of 1kΩ is required.)
7
NU
Up output complement.
(Device will be permanently damaged if pin is instantaneously shorted to
ground. A minimum load impedance magnitude of 1kΩ is required.)
8
Vcc
Supply Voltage.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
MICROWAVE CORPORATION
HMC403S8G
v01.0703
HBT DIGITAL PHASE-FREQUENCY
DETECTOR, DC - 1.3 GHz
Application Circuit
Note: Pins NU and ND should only be probed with high impedance probes.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
FREQ. DIVIDERS & DETECTORS - SMT
10
10 - 71
MICROWAVE CORPORATION
v01.0703
HMC403S8G
HBT DIGITAL PHASE-FREQUENCY
DETECTOR, DC - 1.3 GHz
Evaluation PCB
FREQ. DIVIDER & DETECTORS - SMT
10
List of Materials
Item
Description
J1 - J4
PC Mount SMA RF Connector
J5 - J6
DC Pin
C1
4.7 µF Capacitor
C2 - C6
1000 pF Capacitor, 0402 Pkg.
R1 - R2
1000 Ohm Resistor, 0402 Pkg.
U1
HMC403S8G
PCB*
104741 Eval Board
The circuit board used in the final application should use
RF circuit design techniques. Signal lines should have
50 ohm impedance while the package ground leads
and backside ground slug should be connected directly
to the ground plane similar to that shown. A sufficient
number of via holes should be used to connect the top
and bottom ground planes. The evaluation circuit board
shown is available from Hittite upon request.
* Circuit Board Material: Rogers 4350
10 - 72
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
MICROWAVE CORPORATION
v01.0703
HMC403S8G
HBT DIGITAL PHASE-FREQUENCY
DETECTOR, DC - 1.3 GHz
Notes:
FREQ. DIVIDERS & DETECTORS - SMT
10
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
10 - 73
Similar pages