TI1 ISO7221C-Q1 Dual digital isolator Datasheet

ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
www.ti.com
SLLS965C – JULY 2009 – REVISED MAY 2012
DUAL DIGITAL ISOLATORS
Check for Samples: ISO7220A-Q1, ISO7221A-Q1, ISO7221C-Q1
FEATURES
1
•
•
•
Qualified for Automotive Applications
1-Mbps and 25-Mbps Signaling Rate Options
– Low Channel-to-Channel Output Skew:
1 ns (Max)
– Low Pulse-Width Distortion (PWD):
1 ns (Max)
– Low Jitter Content: 1 ns (Typ) at 150 Mbps
25-Year (Typ) Life at Rated Voltage
(See Application Report SLLA197 and
Figure 14)
•
•
•
•
•
4000-Vpeak Isolation, 560 Vpeak VIORM
– UL 1577, IEC 60747-5-2 (VDE 0884, Rev 2),
IEC 61010-1, IEC 60950-1 and CSA
Approved
– 50 kV/μs Typical Transient Immunity
Operates with 3.3-V or 5-V Supplies
4 kV ESD Protection
High Electromagnetic Immunity
–40°C to 125°C Operating Free-Air
Temperature Range
DESCRIPTION
The ISO7220 and ISO7221 are dual-channel digital isolators. To facilitate PCB layout, the channels are oriented
in the same direction in the ISO7220 and in opposite directions in the ISO7221. These devices have a logic input
and output buffer separated by TI’s silicon-dioxide (SiO2) isolation barrier, providing galvanic isolation of up to
4000 V. Used in conjunction with isolated power supplies, these devices block high voltage, isolate grounds, and
prevent noise currents on a data bus or other circuits from entering the local ground and interfering with or
damaging sensitive circuitry.
A binary input signal is conditioned, translated to a balanced signal, then differentiated by the capacitive isolation
barrier. Across the isolation barrier, a differential comparator receives the logic transition information, then sets or
resets a flip-flop and the output circuit accordingly. A periodic update pulse is sent across the barrier to ensure
the proper dc level of the output. If this dc-refresh pulse is not received every 4 μs, the input is assumed to be
unpowered or not being actively driven, and the failsafe circuit drives the output to a logic high state.
The small capacitance and resulting time constant provide fast operation with signaling rates available from 0
Mbps (dc) to 25 Mbps. (1)The A-option and C-option devices have TTL input thresholds and a noise filter at the
input that prevents transient pulses from being passed to the output of the device.
These devices require two supply voltages of 3.3 V, 5 V, or any combination. All inputs are 5-V tolerant when
supplied from a 3.3-V supply and all outputs are 4-mA CMOS.
These devices are characterized for operation over the ambient temperature range of –40°C to 125°C.
(1)
The signaling rate of a line is the number of voltage transitions that are made per second expressed in the units bps (bits per second).
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009–2012, Texas Instruments Incorporated
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
SLLS965C – JULY 2009 – REVISED MAY 2012
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
SIGNALING
RATE
TA
–40°C to 125°C
(2)
ORDERABLE PART NUMBER
TOP-SIDE MARKING
1 Mbps
SOIC – D
Reel of 2500
ISO7220AQDRQ1
7220AQ
1 Mbps
SOIC – D
Reel of 2500
ISO7221AQDRQ1
7221AQ
25 Mbps
SOIC – D
Reel of 2500
ISO7221CQDRQ1
7221CQ
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
ISO7221
VCC1
1
INA
INB
2
GND1
4
Isolation
ISO7220
3
8
VCC2
7
OUTA
OUTB
GND2
6
5
VCC1
1
OUTA
INB
2
GND1
4
3
Isolation
(1)
PACKAGE (2)
8
VCC2
7
INA
OUTB
GND2
6
5
SINGLE-CHANNEL FUNCTION DIAGRAM
Galvanic Isolation
Barrier
DC Channel
IN
Filter
OSC
+
PWM
Vref
Input
+
Filter
Vref
Pulse Width
Demodulation
Carrier Detect
Data MUX
AC Detect
OUT
Output Buffer
AC Channel
REGULATORY INFORMATION
VDE
CSA
UL
Certified according to IEC 60747-5-2
Approved under CSA Component
Acceptance Notice
Recognized under 1577 Component
Recognition Program (1)
File Number: 40016131
File Number: 1698195
File Number: E181974
(1)
2
Production tested ≥3000 VRMS for 1 second in accordance with UL 1577.
Submit Documentation Feedback
Copyright © 2009–2012, Texas Instruments Incorporated
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
www.ti.com
SLLS965C – JULY 2009 – REVISED MAY 2012
ABSOLUTE MAXIMUM RATINGS (1)
VCC
Supply voltage (2), VCC1, VCC2
–0.5 V to 6 V
VI
Voltage at IN, OUT
–0.5 V to 6 V
IO
Output current
±15 mA
Human-Body Model
ESD
Electrostatic
discharge
±4 kV
Field-Induced Charged-Device Model
All pins
±1 kV
Machine Model
TJ
Maximum junction temperature
Tstg
Storage temperature
(1)
(2)
±200 V
150°C
–65°C to 150°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values except differential I/O bus voltages are with respect to network ground terminal and are peak voltage values.
RECOMMENDED OPERATING CONDITIONS
MIN
VCC
Supply voltage (1)
IOH
High-level output current
IOL
Low-level output current
tui
VCC1, VCC2
TYP
3
MAX
5.5
4
–4
Input pulse width
UNIT
V
mA
mA
ISO722xA
1
0.67
ISO722xC
40
33
ISO722xA
0
1500
ISO722xC
0
30
μs
ns
1000
kbps
25
Mbps
1/tui
Signaling rate
VIH
High-level input voltage
2
VCC
V
VIL
Low-level input voltage
0
0.8
V
TJ
Operating virtual-junction temperature
H
External magnetic field-strength immunity per IEC 61000-4-8 and IEC 61000-4-9 certification
(1)
–40
150
°C
1000
A/m
For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V.
For the 3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
3
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
SLLS965C – JULY 2009 – REVISED MAY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
VCC1 and VCC2 at 5 V (1), over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
ISO7220x
ISO7221x
ICC1
Supply current, VCC1
ISO7220A
ISO7221A
ISO7221C
ISO7220x
ISO7221x
ICC2
Supply current, VCC2
ISO7220A
ISO7221A
ISO7221C
VOH
High-level output voltage
VOL
Low-level output voltage
MIN
Quiescent
1 Mbps
VI = VCC or 0 V, no load
25 Mbps
Quiescent
1 Mbps
VI = VCC or 0 V, no load
25 Mbps
MAX
1
2
8.5
17
2
3
10
18
12
22
16
31
8.5
17
17
32
10
18
12
22
IOH = –4 mA, See Figure 1
VCC – 0.8
4.6
IOH = –20 μA, See Figure 1
VCC – 0.1
5
0.2
0.4
IOL = 20 μA, See Figure 1
0
0.1
150
IIH
High-level input current
IN from 0 V to VCC
IIL
Low-level input current
IN from 0 V to VCC
CI
Input capacitance to ground
IN at VCC, VI = 0.4 sin (4E6πt)
CMTI
Common-mode transient immunity
VI = VCC or 0 V, See Figure 3
UNIT
mA
mA
V
IOL = 4 mA, See Figure 1
VI(HYS) Input voltage hysteresis
(1)
TYP
V
mV
10
μA
μA
–10
1
pF
25
50
kV/μs
MIN
TYP
MAX
UNIT
280
405
480
ns
1
14
ns
22
32
42
ns
1
2
ns
For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V.
For the 3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
SWITCHING CHARACTERISTICS
VCC1 = VCC2 = 5 V, over recommended operating conditions (unless otherwise noted)
PARAMETER
tpLH, tpHL
TEST CONDITIONS
Propagation delay
(1)
ISO722xA
See Figure 1
PWD
Pulse-width distortion |tpHL – tpLH|
tpLH, tpHL
Propagation delay
PWD
Pulse-width distortion |tpHL – tpLH| (1)
tsk(pp)
Part-to-part skew
tsk(o)
Channel-to-channel output skew
tr
Output signal rise time
See Figure 1
1
tf
Output signal fall time
See Figure 1
1
ns
tfs
Failsafe output delay time from input power loss
See Figure 2
3
μs
(1)
(2)
(3)
4
(2)
(3)
ISO722xC
See Figure 1
ISO722xA
180
ISO722xC
10
ISO722xA
3
15
ISO722xC
0.2
1
ns
ns
ns
Also referred to as pulse skew.
tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the
same direction while driving identical specified loads.
Submit Documentation Feedback
Copyright © 2009–2012, Texas Instruments Incorporated
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
www.ti.com
SLLS965C – JULY 2009 – REVISED MAY 2012
ELECTRICAL CHARACTERISTICS
VCC1 = 5 V, VCC2 = 3.3 V (1), over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
ISO7220x
ISO7221x
ICC1
Supply current, VCC1
ISO7220A
ISO7221A
ISO7221C
ISO7220x
ISO7221x
ICC2
Supply current, VCC2
ISO7220A
ISO7221A
ISO7221C
Quiescent
VI = VCC or 0 V, no load
1 Mbps
VI = VCC or 0 V, no load
25 Mbps
VI = VCC or 0 V, no load
Quiescent
VI = VCC or 0 V, no load
1 Mbps
VI = VCC or 0 V, no load
25 Mbps
VI = VCC or 0 V, no load
MIN
ISO7220x
VOH
ISO7221x
(5-V side)
High-level output voltage
Low-level output voltage
1
2
8.5
17
2
3
10
18
12
22
8
18
4.3
9.5
9
19
5
11
6
12
VCC – 0.8
UNIT
mA
mA
V
VCC – 0.1
IOL = 4 mA, See Figure 1
0.4
IOL = 20 μA, See Figure 1
0.1
VI(HYS) Input voltage hysteresis
150
IIH
High-level input current
IN from 0 V to VCC
IIL
Low-level input current
IN from 0 V to VCC
CI
Input capacitance to ground
IN at VCC, VI = 0.4 sin (4E6πt)
CMTI
Common-mode transient immunity
VI = VCC or 0 V, See Figure 3
(1)
MAX
VCC – 0.4
IOH = –4 mA, See Figure 1
IOH = –20 μA, See Figure 1
VOL
TYP
V
mV
10
μA
μA
–10
1
pF
15
40
kV/μs
MIN
TYP
MAX
UNIT
285
410
480
ns
1
14
ns
36
48
ns
2
ns
For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V.
For the 3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
SWITCHING CHARACTERISTICS
VCC1 = 5 V, VCC2 = 3.3 V, over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
tpLH, tpHL
Propagation delay
PWD
Pulse-width distortion |tpHL – tpLH| (1)
tpLH, tpHL
Propagation delay
PWD
Pulse-width distortion |tpHL – tpLH|
(1)
(2)
ISO722xA
ISO722xC
See Figure 1
25
See Figure 1
1
ISO722xA
180
ISO722xC
10
tsk(pp)
Part-to-part skew
tsk(o)
Channel-to-channel output skew
tr
Output signal rise time
See Figure 1
2
tf
Output signal fall time
See Figure 1
2
tfs
Failsafe output delay time from input power loss
See Figure 2
3
(1)
(2)
(3)
(3)
ISO722xA
3
15
ISO722xC
0.2
1
ns
ns
ns
μs
Also referred to as pulse skew.
tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the
same direction while driving identical specified loads.
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
5
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
SLLS965C – JULY 2009 – REVISED MAY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
VCC1 = 3.3 V, VCC2 = 5 V (1), over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
ISO7220x
ISO7221x
ICC1
Supply current, VCC1
ISO7220A
ISO7221A
ISO7221C
ISO7220x
ISO7221x
ICC2
Supply current, VCC2
ISO7220A
ISO7221A
ISO7221C
Quiescent
1 Mbps
VI = VCC or 0 V, no load
25 Mbps
Quiescent
1 Mbps
VI = VCC or 0 V, no load
25 Mbps
ISO7220x
VOH
ISO7221x
(3.3-V side)
High-level output voltage
0.6
1
4.3
9.5
1
2
5
11
6
12
16
31
8.5
17
18
32
10
18
12
22
UNIT
mA
mA
V
VCC – 0.1
IOL = 4 mA, See Figure 1
Low-level output voltage
MAX
VCC – 0.4
0.4
IOL = 20 μA, See Figure 1
0
VI(HYS) Input threshold voltage hysteresis
0.1
150
IIH
High-level input current
IN from 0 V or VCC
IIL
Low-level input current
IN from 0 V or VCC
CI
Input capacitance to ground
IN at VCC, VI = 0.4 sin (4E6πt)
CMTI
Common-mode transient immunity
VI = VCC or 0 V, See Figure 3
(1)
TYP
VCC – 0.8
IOH = –4 mA, See Figure 1
IOH = –20 μA, See Figure 1
VOL
MIN
V
mV
10
μA
μA
–10
1
pF
15
40
kV/μs
MIN
TYP
MAX
UNIT
285
395
480
ns
1
18
ns
36
48
ns
3
ns
For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V.
For the 3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
SWITCHING CHARACTERISTICS
VCC1 = 3.3 V, VCC2 = 5 V, over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
tpLH, tpHL
Propagation delay
PWD
Pulse-width distortion |tpHL – tpLH| (1)
tpLH, tpHL
Propagation delay
PWD
Pulse-width distortion |tpHL – tpLH|
(1)
(2)
ISO722xA
ISO722xC
See Figure 1
24
See Figure 1
1
ISO722xA
190
ISO722xC
10
tsk(pp)
Part-to-part skew
tsk(o)
Channel-to-channel output skew
tr
Output signal rise time
See Figure 1
1
tf
Output signal fall time
See Figure 1
1
ns
tfs
Failsafe output delay time from input power loss
See Figure 2
3
μs
(1)
(2)
(3)
6
(3)
ISO722xA
3
15
ISO722xC
0.2
1
ns
ns
ns
Also referred to as pulse skew.
tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the
same direction while driving identical specified loads.
Submit Documentation Feedback
Copyright © 2009–2012, Texas Instruments Incorporated
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
www.ti.com
SLLS965C – JULY 2009 – REVISED MAY 2012
ELECTRICAL CHARACTERISTICS
VCC1 = VCC2 = 3.3 V (1), over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
ISO7220x
ISO7221x
ICC1
Supply current, VCC1
ISO7220A
ISO7221A
ISO7221C
ISO7220x
ISO7221x
ICC2
Supply current, VCC2
ISO7220A
ISO7221A
ISO7221C
VOH
High-level output voltage
VOL
Low-level output voltage
MIN
Quiescent
1 Mbps
VI = VCC or 0 V, no load
25 Mbps
Quiescent
1 Mbps
VI = VCC or 0 V, no load
25 Mbps
MAX
0.6
1
4.3
9.5
1
2
5
11
6
12
8
18
4.3
9.5
9
19
5
11
6
12
IOH = –4 mA, See Figure 1
VCC – 0.4
3
IOH = –20 μA, See Figure 1
VCC – 0.1
3.3
0.2
0.4
IOL = 20 μA, See Figure 1
0
0.1
150
IIH
High-level input current
IN from 0 V or VCC
IIL
Low-level input current
IN from 0 V or VCC
CI
Input capacitance to ground
IN at VCC, VI = 0.4 sin (4E6πt)
CMTI
Common-mode transient immunity
VI = VCC or 0 V, See Figure 3
UNIT
mA
mA
V
IOL = 4 mA, See Figure 1
VI(HYS) Input voltage hysteresis
(1)
TYP
V
mV
10
μA
μA
–10
1
pF
15
40
kV/μs
MIN
TYP
MAX
UNIT
290
400
485
ns
1
18
ns
25
40
52
ns
1
3
ns
For the 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V.
For the 3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
SWITCHING CHARACTERISTICS
VCC1 = VCC2 = 3.3 V, over recommended operating conditions (unless otherwise noted)
PARAMETER
tpLH, tpHL
TEST CONDITIONS
Propagation delay
(1)
ISO722xA
See Figure 1
PWD
Pulse-width distortion |tpHL – tpLH|
tpLH, tpHL
Propagation delay
PWD
Pulse-width distortion |tpHL – tpLH| (1)
tsk(pp)
Part-to-part skew (2)
tsk(o)
Channel-to-channel output skew
tr
Output signal rise time
See Figure 1
2
tf
Output signal fall time
See Figure 1
2
ns
tfs
Failsafe output delay time from input power loss
See Figure 2
3
μs
(1)
(2)
(3)
(3)
ISO722xC
See Figure 1
ISO722xA
190
ISO722xC
10
ISO722xA
3
15
ISO722xC
0.2
1
ns
ns
ns
Also referred to as pulse skew.
tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
tsk(o) is the skew between specified outputs of a single device with all driving inputs connected together and the outputs switching in the
same direction while driving identical specified loads.
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
7
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
SLLS965C – JULY 2009 – REVISED MAY 2012
www.ti.com
ISOLATION BARRIER
PARAMETER MEASUREMENT INFORMATION
IN
Input
Generator
VI
50 W
NOTE A
VCC1
VI
VCC1/2
VCC1/2
OUT
0V
tPHL
tPLH
CL
NOTE B
VO
VO
VOH
90%
50%
50%
10%
tr
VOL
tf
A.
The input pulse is supplied by a generator having the following characteristics: PRR ≤ 50 kHz, 50% duty cycle, tr ≤ 3
ns, tf ≤ 3 ns, ZO = 50Ω.
B.
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 1. Switching Characteristic Test Circuit and Voltage Waveforms
VI
0V
or
VCC1
A.
ISOLATION BARRIER
VCC1
IN
VCC1
OUT
VI
2.7 V
VO
0V
VOH
tfs
CL
NOTE A
VO
50%
FAILSAFE HIGH
VOL
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 2. Failsafe Delay Time Test Circuit and Voltage Waveforms
VCC1
VCC2
S1
ISOLATION BARRIER
C = 0.1 mF± 1%
IN
GND1
C = 0.1 mF± 1%
Pass-fail criteria:
Output must
remain stable
OUT
NOTE A
VOH or VOL
GND2
VCM
A.
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 3. Common-Mode Transient Immunity Test Circuit
VCC1
DUT
Tektronix
HFS9009
IN
OUT
0V
Tektronix
784D
PATTERN
GENERATOR
VCC/2
Jitter
NOTE: PRBS bit pattern run length is 216 – 1. Transition time is 800 ps.
Figure 4. Peak-to-Peak Eye-Pattern Jitter Test Circuit and Voltage Waveform
8
Submit Documentation Feedback
Copyright © 2009–2012, Texas Instruments Incorporated
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
www.ti.com
SLLS965C – JULY 2009 – REVISED MAY 2012
DEVICE INFORMATION
IEC PACKAGE CHARACTERISTICS
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
L(I01)
Minimum air gap (clearance)
Shortest terminal-to-terminal distance through air
L(I02)
Minimum external tracking
(creepage)
Shortest terminal-to-terminal distance across the
package surface
CTI
Tracking resistance
(comparative tracking index)
DIN IEC 60112 / VDE 0303 Part 1
≥175
V
Minimum internal gap (internal
clearance)
Distance through the insulation
0.008
mm
RIO
SOIC-8
4.8
mm
4.3
mm
Input to output, VIO = 500 V, all pins on each side of the barrier
tied together creating a two-terminal device, TA < 100°C
Isolation resistance
Input to output, VIO = 500 V, 100°C ≤ TA ≤ max
>1012
Ω
11
Ω
>10
CIO
Barrier capacitance input to
output
VI = 0.4 sin (4E6πt)
1
pF
CI
Input capacitance to ground
VI = 0.4 sin (4E6πt)
1
pF
NOTE: Creepage and clearance requirements should be applied according to the specific equipment isolation
standards of an application. Care should be taken to maintain the creepage and clearance distance of a board
design to ensure that the mounting pads of the isolator on the printed circuit board do not reduce this distance.
Creepage and clearance on a printed circuit board become equal according to the measurement techniques
shown in the Isolation Glossary . Techniques such as inserting grooves and/or ribs on a printed circuit board are
used to help increase these specifications.
IEC 60664-1 RATINGS TABLE
PARAMETER
Basic isolation group
Installation classification
TEST CONDITIONS
SPECIFICATION
Material group
IIIa
Rated mains voltage ≤150 VRMS
I-IV
Rated mains voltage ≤300 VRMS
I-III
Rated mains voltage ≤400 VRMS
I-II
IEC 60747-5-2 INSULATION CHARACTERISTICS (1)
PARAMETER
VIORM
TEST CONDITIONS
Maximum working insulation voltage
SPECIFICATION
UNIT
560
V
1050
V
VPR
Input to output test voltage
Method b1, VPR = VIORM × 1.875,
100% Production test with t = 1 s,
Partial discharge <5 pC
VIOTM
Transient overvoltage
t = 60 s
4000
V
RS
Insulation resistance
VIO = 500 V at TS
>109
Ω
Pollution degree
(1)
2
Climatic Classification 40/125/21
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
9
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
SLLS965C – JULY 2009 – REVISED MAY 2012
www.ti.com
DEVICE I/O SCHEMATICS
Input
VCC1
VCC1
VCC1
Output
VCC2
750 kW
8W
500 W
IN
OUT
13 W
IEC SAFETY LIMITING VALUES
Safety limiting intends to prevent potential damage to the isolation barrier upon failure of input or output circuitry.
A failure of the IO can allow low resistance to ground or the supply and, without current limiting, dissipate
sufficient power to overheat the die and damage the isolation barrier potentially leading to secondary system
failures.
PARAMETER
TEST CONDITIONS
IS
Safety input, output, or
supply current
SOIC-8
TS
Maximum case temperature
SOIC-8
MIN
MAX
θJA = 212°C/W, VI = 5.5 V, TJ = 170°C, TA = 25°C
124
θJA = 212°C/W, VI = 3.6 V, TJ = 170°C, TA = 25°C
190
150
UNIT
mA
°C
The safety-limiting constraint is the absolute maximum junction temperature specified in the absolute maximum
ratings table. The power dissipation and junction-to-air thermal impedance of the device installed in the
application hardware determines the junction temperature. The assumed junction-to-air thermal resistance in the
Thermal Characteristics table is that of a device installed in the JESD51-3, Low Effective Thermal Conductivity
Test Board for Leaded Surface Mount Packages and is conservative. The power is the recommended maximum
input voltage times the current. The junction temperature is then the ambient temperature plus the power times
the junction-to-air thermal resistance.
10
Submit Documentation Feedback
Copyright © 2009–2012, Texas Instruments Incorporated
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
www.ti.com
SLLS965C – JULY 2009 – REVISED MAY 2012
SOIC-8 PACKAGE THERMAL CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Low-K thermal resistance
θJA
Junction-to-air thermal resistance
θJB
Junction-to-board thermal resistance
θJC
Junction-to-case thermal resistance
(1)
MIN
TYP
(1)
MAX
212
High-K thermal resistance
122
UNIT
°C/W
37
°C/W
69.1
°C/W
Tested in accordance with the Low-K or High-K thermal metric definitions of EIA/JESD51-3 for leaded surface mount packages.
250
225
VCC1,2 at 3.6 V
Safety Limiting Current - mA
200
175
150
125
VCC1,2 at 5.5 V
100
75
50
25
0
0
50
100
150
TC - Case Temperature - °C
200
Figure 5. SOIC-8 θJC THERMAL DERATING CURVE per IEC 60747-5-2
DEVICE FUNCTION TABLE
Table 1. ISO7220x or ISO7221x (1)
INPUT SIDE VCC
OUTPUT SIDE VCC
PU
PU
PD
(1)
PU
INPUT IN
OUTPUT OUT
H
H
L
L
Open
H
X
H
PU = Powered up(Vcc ≥ 3.0 V), PD = Powered down (Vcc ≤ 2.5 V), X = Irrelevant, H = High level,
L = Low level
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
11
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
SLLS965C – JULY 2009 – REVISED MAY 2012
www.ti.com
TYPICAL CHARACTERISTIC CURVES
3.3-V RMS SUPPLY CURRENT
vs
SIGNALING RATE (Mbps)
5-V RMS SUPPLY CURRENT
vs
SIGNALING RATE (Mbps)
20
30
TA = 25°C,
15 pF Load
18
26
ISO7220x ICC2
24
14
ICC - Supply Current - mA
16
ICC - Supply Current - mA
TA = 25°C,
15 pF Load
28
ISO7220x ICC2
12
10
ISO7221x ICC1&2
8
6
4
ISO7220x ICC1
22
20
ISO7221x ICC1&2
18
16
14
12
10
ISO7220x ICC1
8
6
4
2
2
0
0
0
25
50
75
0
100
25
Signaling Rate - Mbps
50
75
Signaling Rate - Mbps
100
Figure 6.
Figure 7.
ISO722xA AND ISO722xC INPUT VOLTAGE LOW-TO-HIGH
SWITCHING THRESHOLD
vs
FREE-AIR TEMPERATURE
VCC FAILSAFE THRESHOLD
vs
FREE-AIR TEMPERATURE
2.92
1.4
5-V Vth+
1.35
2.9
15 pF Load
VCC = 3.3 V or 5 V
3.3-V Vth+
2.88
1.25
15 pF Load
1.2
1.15
5-V Vth1.1
Failsafe Threshold - V
Input Voltage Threshold - V
VFS
1.3
2.86
2.84
2.82
VFS2.8
1.05
3.3-V Vth1
-40 -25 -10
5
20
35
50
65
Temperature - °C
Figure 8.
12
Submit Documentation Feedback
80
95
110 125
2.78
-40 -25 -10
5
20
35
50
65
80
95
110 125
Temperature - °C
Figure 9.
Copyright © 2009–2012, Texas Instruments Incorporated
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
www.ti.com
SLLS965C – JULY 2009 – REVISED MAY 2012
TYPICAL CHARACTERISTIC CURVES (continued)
HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
LOW-LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOLTAGE
70
-80
15 pF Load
TA = 25°C
-70
15 pF Load
TA = 25°C
60
VCC = 5 V
-60
50
VCC = 5 V
IOUT - mA
IOUT - mA
-50
-40
-30
VCC = 3.3 V
-20
40
VCC = 3.3 V
30
20
10
-10
0
0
0
2
4
6
0
1
2
3
VOUT - V
VOUT - V
Figure 10.
Figure 11.
Copyright © 2009–2012, Texas Instruments Incorporated
4
Submit Documentation Feedback
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
5
13
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
SLLS965C – JULY 2009 – REVISED MAY 2012
www.ti.com
APPLICATION INFORMATION
Typical Applications
V CC 1
V CC 2
0.1mF
2 mm
max .
from
Vcc 1
INPUT
1
INA 2
INB
INPUT
3
4
8
OUTA
7
OUTB
6
5
2 mm
max .
from
Vcc 2
0.1mF
OUTPUT
OUTPUT
ISO 7220
GND 1
GND 2
Figure 12. Typical ISO7220 Application Circuit
V CC 1
V CC 2
0.1mF
2 mm
max .
from
Vcc 1
OUTA
OUTPUT
INB
INPUT
1
2
3
4
8
INA
7
OUTB
6
5
2 mm
max .
from
Vcc 2
0.1mF
INPUT
OUTPUT
ISO 7221
GND 1
GND 2
Figure 13. Typical ISO7221 Application Circuit
WORKING LIFE -- YEARS
100
VIORM at 560 V
28
10
0
120
250
500
750
880
1000
WORKING VOLTAGE (V IORM ) -- V
Figure 14. Time-Dependent Dielectric Breakdown Test Results
14
Submit Documentation Feedback
Copyright © 2009–2012, Texas Instruments Incorporated
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
www.ti.com
SLLS965C – JULY 2009 – REVISED MAY 2012
ISOLATION GLOSSARY
Creepage Distance — The shortest path between two conductive input to output leads measured along the
surface of the insulation. The shortest distance path is found around the end of the package body.
Clearance — The shortest distance between two conductive input to output leads measured through air (line of
sight).
Input-to Output Barrier Capacitance — The total capacitance between all input terminals connected together,
and all output terminals connected together.
Input-to Output Barrier Resistance — The total resistance between all input terminals connected together, and
all output terminals connected together.
Primary Circuit — An internal circuit directly connected to an external supply mains or other equivalent source
which supplies the primary circuit electric power.
Secondary Circuit — A circuit with no direct connection to primary power, and derives its power from a separate
isolated source.
Comparative Tracking Index (CTI) — CTI is an index used for electrical insulating materials which is defined as
the numerical value of the voltage which causes failure by tracking during standard testing. Tracking is the
process that produces a partially conducting path of localized deterioration on or through the surface of an
insulating material as a result of the action of electric discharges on or close to an insulation surface -- the higher
CTI value of the insulating material, the smaller the minimum creepage distance.
Generally, insulation breakdown occurs either through the material, over its surface, or both. Surface failure may
arise from flashover or from the progressive degradation of the insulation surface by small localized sparks. Such
sparks are the result of the breaking of a surface film of conducting contaminant on the insulation. The resulting
break in the leakage current produces an overvoltage at the site of the discontinuity, and an electric spark is
generated. These sparks often cause carbonization on insulation material and lead to a carbon track between
points of different potential. This process is known as tracking.
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
15
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
SLLS965C – JULY 2009 – REVISED MAY 2012
www.ti.com
Insulation:
Operational insulation — Insulation needed for the correct operation of the equipment.
Basic insulation — Insulation to provide basic protection against electric shock.
Supplementary insulation — Independent insulation applied in addition to basic insulation in order to ensure
protection against electric shock in the event of a failure of the basic insulation.
Double insulation — Insulation comprising both basic and supplementary insulation.
Reinforced insulation — A single insulation system which provides a degree of protection against electric shock
equivalent to double insulation.
Pollution Degree:
Pollution Degree 1 — No pollution, or only dry, nonconductive pollution occurs. The pollution has no influence.
Pollution Degree 2 — Normally, only nonconductive pollution occurs. However, a temporary conductivity caused
by condensation must be expected.
Pollution Degree 3 — Conductive pollution occurs or dry nonconductive pollution occurs which becomes
conductive due to condensation which is to be expected.
Pollution Degree 4 – Continuous conductivity occurs due to conductive dust, rain, or other wet conditions.
Installation Category:
Overvoltage Category — This section is directed at insulation co-ordination by identifying the transient
overvoltages which may occur, and by assigning 4 different levels as indicated in IEC 60664.
I: Signal Level — Special equipment or parts of equipment.
II: Local Level — Portable equipment etc.
III: Distribution Level — Fixed installation
IV: Primary Supply Level — Overhead lines, cable systems
Each category should be subject to smaller transients than the category above.
16
Submit Documentation Feedback
Copyright © 2009–2012, Texas Instruments Incorporated
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
ISO7220A-Q1
ISO7221A-Q1
ISO7221C-Q1
www.ti.com
SLLS965C – JULY 2009 – REVISED MAY 2012
REVISION HISTORY
Changes from Revision B (March 2010) to Revision C
•
Page
Added storage temperature to Abs Max table. ..................................................................................................................... 3
Copyright © 2009–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): ISO7220A-Q1 ISO7221A-Q1 ISO7221C-Q1
17
PACKAGE OPTION ADDENDUM
www.ti.com
22-May-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
ISO7220AQDRQ1
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ISO7221AQDRQ1
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
ISO7221CQDRQ1
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF ISO7220A-Q1, ISO7221A-Q1, ISO7221C-Q1 :
• Catalog: ISO7220A, ISO7221A, ISO7221C
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
22-May-2012
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
ISO7220AQDRQ1
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
ISO7221AQDRQ1
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
ISO7221CQDRQ1
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ISO7220AQDRQ1
SOIC
D
8
2500
367.0
367.0
35.0
ISO7221AQDRQ1
SOIC
D
8
2500
367.0
367.0
35.0
ISO7221CQDRQ1
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
Similar pages