Cypress CY3950I Delta39k⁄ultra37000 isr programming kit Datasheet

CY3900I / CY3950I
Delta39K™⁄Ultra37000™ ISR™ Programming Kits
Features
Functional Description
• Supports Cypress’s Ultra37000™, Ultra37000V™,
Delta39K™, and PSI™ families of products
• STAPL (Chain Dependent and Chain Independent)
programming language support
• SVF programming language support
• Standard JTAG programming interface
• Multi-device programming
• Easy to use Windows XP-™, Windows 2000-™,
Windows ME-™, Windows 98-™, and Windows
NT™-compatible interface
• Eliminates programming insertion to improve
manufacturing efficiency
• For programming in the lab, on manufacturing floor, or
at remote sites
• ATE support via STAPL on industry leading ATE
platforms
CY3900I Kit Contents
• ISR Programming Software Release 4.0
• C3ISR™ Programming Cable[3] for use with Ultra37000,
Delta39K, and PSI CPLD families
• Delta39K/Ultra37000 prototype board[1]
• ISR application notes
CY3950I Kit Contents
The Delta39K/Ultra37000 ISR Programming Kit enables users
to program Ultra37000, Ultra37000V, Delta39K, and PSI
CPLDs on board with our ISR Programming Software, the
C3ISR or USBISR Programming Cable, and a personal
computer. The C3ISR Programming Cable connects to the
parallel port of a PC and the USBISR Programming Cable[3]
connects to a USB 1.1/USB 2.0 port of a PC into a standard
10-pin male connector mounted on the user’s board. The ISR
software provides an easy-to-use Graphical User Interface
that accepts JEDEC or hex files as input. The JEDEC/.hex files
are used to compose platform independent STAPL/SVF files.
STAPL/SVF files contain all the information needed to
program the device. The ISR software is used to define how
many devices are in the daisy chain and what operation is to
be done on each Cypress device. The same chain can be used
with other JTAG-compliant devices.
The ISR User’s Guide describes the operation of the ISR
software. The application notes included with the kit describe
all system design considerations for programming with this
Programming Kit.
10-pin Programming Connector
The diagram below shows the pinout of the 10-pin male
connector to be mounted onto the board.
The view looking down onto the board connector pins is shown
below.
• ISR Programming Software Release 4.0
• USBISR Programming Cable[3] for use with Ultra37000,
Delta39K, and PSI CPLD families
• Delta39K/Ultra37000 prototype board[1]
• ISR application notes
TDO
VCC
ISR[2]
JTAGen
GND[2]
GND
NC
TDI
TCK
TMS
In-System Reprogrammable™ (ISR™) Programming (using C3ISR cable[3])
VCC
Cypress
10-pin
Cable
PC
25-pin
Device
Parallel Port
Cypress
10-pin ISR Connector
Device
Designer’s
Board
Notes:
1. Cypress reserves the right to substitute prototype boards based on product availability.
2. Refer to the CD-ROM ISR User’s Guide documentation for detailed information on ISR programming and electrical specification requirements.
3. The C3ISR Programming Cable is available in the CY3900I Programming Kit and the USBISR Programming Cable is available in the CY3950I Programming Kit.
Cypress Semiconductor Corporation
Document #: 38-03009 Rev. *C
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised October 09, 2003
CY3900I / CY3950I
In-System Reprogrammable™ (ISR™) Programming (using USBISR cable[3])
VCC
Cypress
10-pin
Cable
PC
USB
Device
USB 1.1 / USB 2.0 Port
Cypress
Device
Designer’s
10-pin ISR Connector
Board
Table 1. C3ISR / USBISR Cable Pin Descriptions
Pin
JTAGen
ISR*
VCC
TDO
Type
OUTPUT
OUTPUT
INPUT
INPUT
TMS
OUTPUT
TCK
TDI
OUTPUT
OUTPUT
NC
GND
NC
—
Description
In System Reprogramming JTAG Enable (active HIGH).
In System Reprogramming Enable Indicator (active LOW).
+5V and +3.3V Supply Voltage provided from the target system to the cable.
Test Data Output Receiver. The TDO output pin of the last device in the ISR chain of
the system is connected to this input pin.
Test Mode Control. This is the mode select control input for the TAP controller state
machine contained in the ISR interface.
Test Clock. ISR interface clock.
Test Data Input Driver. This output pin is connected to the TDI input of the first device
in the ISR chain.
No Connect.
Zero volt common ground for PC and target system.
Table 1 describes the function of each of these pins on the
C3ISR and USBISR Programming Cables. An OUTPUT is
provided by the PC and an INPUT is provided by the target
system.
Pin cross-section is 0.025” x 0.025”.
The dimensions of the male connector required for the C3ISR
and the USBISR Programming Cables are given below.
Digi-Key S2112-05-ND (right-angle connector).
Male Connector
2 x 5 = 2 rows, 5 pins per row
Measuring from center of the pins, each pin is 0.1” from the
others.
Pin length is 0.23”.
Document #: 38-03009 Rev. *C
Part Number
Digi-Key® S2012-05-ND (straight-pin connector).
To facilitate easy and quick prototyping of designs, a
Delta39K/Ultra37000 Prototype Board[4] has been included in
the CY3900i Delta39/Ultra37000 ISR Programming Kit. The
prototype board comes with a CY37256VP160 device and a
CY39100V208 device already premounted and header strips
that facilitate signal testing. Detailed information on the board
layout and proper usage may be found in the Cypress application note, Using the Delta39K ISR Prototype Board.
Page 2 of 4
CY3900I / CY3950I
ISR 10-pin
Connector
J2
CY39100V208
208-pin
TQFP
10-pin
Connector
VCCO GND
J3
Header Strips
CY37256VP160
Power
Connector
Header
160-pin
TQFP
Strips
Daisy Chain Jumpers
LED
VCC GND
Power
Connector
Figure 1. Delta39K/Ultra37000 Prototype Board
PC System Requirements
• IBM PC or compatible running Windows 98, Windows 98
Second Edition, Windows ME, Windows NT 4.0 Service
Pack 5 or later or Windows 2000 Service Pack 1 or later
and Windows XP.
• One free parallel, USB 1.1 or 2.0 (recommended) port
• A minimum of 32 MB of RAM.
• Approximately 30 MB of free hard disk space.
Ordering Information
Product
Code
Description
CY3950I
Delta39K/Ultra37000 ISR Programming Kit
(with USBISR Programming Cable)
CY3900I
Delta39K/Ultra37000 ISR Programming Kit
(with C3ISR parallel Programming Cable)
Windows 98, Windows ME, Windows 2000, Windows NT and Windows XP are trademarks of Microsoft Corporation. Digi-Key is
a registered trademark of Digi-Key Corporation. ISR, C3ISR, USBISR, Ultra37000, Delta39K, and PSI are trademarks of Cypress
Semiconductor.
Note:
4. See Figure 1 for the basic layout.
Document #: 38-03009 Rev. *C
Page 3 of 4
© Cypress Semiconductor Corporation, 2003. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
CY3900I / CY3950I
Document History Page
Document Title: Delta39K™/Ultra37000™ ISR™ Programming Kit
Document Number: 38-03009
REV.
ECN NO.
Issue
Date
Orig. of
Change
Description of Change
**
108980
08/07/01
HOW
New Data Sheet
*A
111228
01/23/02
CNH
Removed references to Windows 95
*B
127867
08/18/03
FSG
Removed Quantum38K from all pages
*C
130222
10/09/03
FSG
Added CY3950I kit
Document #: 38-03009 Rev. *C
Page 4 of 4
Similar pages