Hittite HMC380QS16GE Pcs/umts high ip3 rfic downconverter, 1.7 - 2.2 ghz Datasheet

HMC380QS16G / 380QS16GE
v02.0305
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.7 - 2.2 GHz
8
Typical Applications
Features
The HMC380QS16G / HMC380QS16GE is ideal for:
+19 dBm Input IP3
• GSM, GPRS & EDGE Infrastructure
Low LO Drive: -5 dBm
• CDMA, WCDMA Infrastructure
Conversion Gain: 11 dB
• PHS Infrastructure
Noise Figure: 9 dB
MIXERS - DOWNCONVERTERS - SMT
Single Positive Supply: +5V, 165 mA
Functional Diagram
General Description
The HMC380QS16G & HMC380QS16GE are high
linearity down-converter receiver ICs suitable for
PCS/UMTS infrastructure applications from 1.7 - 2.2
GHz. The receiver IC is designed to support UMTS
applications where a high third order intercept
point is required. A passive mixer coupled with a
high dynamic range IF amplifier achieves an input
IP3 of +19 dBm. The converter provides a gain of
11.5 dB and 9 dB typical single side band noise
figure. The IC operates from a positive +5V rail
consuming 165 mA of current while only requiring a
-5 dBm LO drive. The design requires no external
baluns. The mixer supports IF frequencies between
50 MHz and 300 MHz.
Electrical Specifi cations, TA = +25° C, LO = -5 dBm, Vdd = 5V, IF = 250 MHz [1]
Parameter
Min.
Typ.
Max.
Min.
Typ.
Max.
Frequency Range, RF
1.7 - 2.0
2.0 - 2.2
Frequency Range, LO
1.4 - 1.95
1.7 - 2.15
GHz
Frequency Range, IF [2]
50 - 300
50 - 300
MHz
9
11.5
dB
Conversion Gain
9
11.5
Noise Figure (SSB)
9.2
10.5
10
GHz
11.5
dB
LO to RF Isolation
20
25
23
28
dB
LO to IF Isolation
22
32
30
38
dB
RF to IF Isolation
38
50
46
54
dB
IP3 (Input)
17
19
17
19
dBm
1 dB Compression (Input)
3
5
3
LO Input Drive Level (Typical)
Supply Current (Idd for LO & IF)
(IF bias resistor= 3.3 Ohms)
6
dBm
-5 to 0
-5 to 0
dBm
175
175
mA
[1] Unless otherwise noted all measurements with low side LO & IF = 250 MHz.
[2] If matching must be tuned for optimal results, see application circuit herein.
8 - 62
Units
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC380QS16G / 380QS16GE
v02.0305
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.7 - 2.2 GHz
Isolation
Conversion Gain vs. Temperature
0
9
+25 C
+85 C
-40 C
7
8
-20
-30
-40
-50
-60
1.6
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
1.6
2.3
Conversion Gain vs. LO Drive
1.7
1.8
1.9
2
2.1
FREQUENCY (GHz)
2.2
2.3
2.2
2.3
Return Loss
15
0
RETURN LOSS (dB)
13
11
9
LO = -8 dBm
LO = -5 dBm
LO = -2 dBm
LO = 0 dBm
7
-5
-10
RF
LO
5
-15
1.6
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
1.6
2.3
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
IF Bandwidth
Input P1dB vs. Temperature
10
MIXERS - DOWNCONVERTERS - SMT
11
5
CONVERSION GAIN (dB)
RF TO IF
LO TO RF
LO TO IF
-10
13
ISOLATION (dB)
CONVERSION GAIN (dB)
15
14
10
RESPONSE (dB)
INPUT P1dB (dBm)
8
6
4
+ 25C
+ 85C
- 40C
2
2
CONVERSION GAIN
RETURN LOSS
-2
-6
-10
0
1.6
6
-14
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
2.3
50
150
250
350
IF FREQUENCY (MHz)
450
* Unless otherwise noted all measurements with low side LO & IF = 250 MHz.
** If matching must be tuned for optimal results, see application circuit herein.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 63
HMC380QS16G / 380QS16GE
v02.0305
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.7 - 2.2 GHz
Input and Output IP3 vs. Temperature
Input and Output IP3 vs LO Drive
40
40
OIP3
OIP3
IP3 (dBm)
IP3 (dBm)
30
IIP3
20
OIP3, +25C
OIP3, +85C
OIP3, -40C
10
IIP3, +25C
IIP3, +85C
IIP3, -40C
1.6
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
2.3
OIP3, LO=-5dBm
OIP3, LO=-2dBm
OIP3, LO= 0dBm
IIP3, LO=-5dBm
IIP3, LO=-2dBm
IIP3, LO= 0dBm
1.6
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.3
350
400
2.2
2.3
15
+ 25C
+ 85C
- 40C
13
NOISE FIGURE (dB)
13
11
9
7
11
9
7
5
5
1.7
1.8
1.9
2
2.1
RF FREQUENCY (GHz)
2.2
2.3
Conversion Gain
with IF Tuned for 70 MHz
50
100
150
200
250
300
IF FREQUENCY (MHz)
IP3 with IF Tuned for 70 MHz
15
40
INPUT IP3
OUTPUT IP3
13
IP3 (dBm)
30
11
9
20
10
7
5
1.6
1.7
1.8
1.9
2
2.1
2.2
2.3
0
1.6
FREQUENCY (GHz)
1.7
1.8
1.9
2
2.1
FREQUENCY (GHz)
* Unless otherwise noted all measurements with low side LO & IF = 250 MHz.
** If matching must be tuned for optimal results, see application circuit herein.
8 - 64
2.2
Noise Figure
Swept IF, Fixed LO = 1.7 GHz
15
CONVERSION GAIN (dB)
20
0
1.7
Noise Figure vs Temperature
Swept LO, Fixed IF = 250 MHz
1.6
IIP3
10
0
NOISE FIGURE (dB)
MIXERS - DOWNCONVERTERS - SMT
8
30
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC380QS16G / 380QS16GE
v02.0305
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.7 - 2.2 GHz
MxN Spurious @ IF Port
Harmonics of LO
nLO Spur @ RF Port
0
1
2
3
0
xx
40
60
58
35
1
62
0
62
87
102
2
124
101
55
94
110
1.8
3
126
126
113
76
112
2.0
4
121
127
128
124
116
2.2
2.4
23
RF Freq. = 1.9 GHz @ -10 dBm
LO Freq. = 1.65 GHz @ -5 dBm
All values in dBc relative to the IF power level.
4
LO Freq. (GHz)
1
2
3
1.4
23
3
16
15
1.6
26
6
12
18
26
8
10
29
24
8
12
31
38
10
14
35
12
19
40
LO = -5 dBm
All values in dBc below input LO level measured at RF port.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4
8
MIXERS - DOWNCONVERTERS - SMT
nLO
mRF
8 - 65
HMC380QS16G / 380QS16GE
v02.0305
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.7 - 2.2 GHz
Absolute Maximum Ratings
MIXERS - DOWNCONVERTERS - SMT
8
Typical Supply Current vs. Vdd
RF / IF Input (Vdd= +5V)
+13 dBm
Vdd (LO + IF)
Idd (mA)
LO Drive (Vdd= +5V)
+15 dBm
+4.5
162
Vdd (LO or IF)
+7 Vdc
+5.0
165
Channel Temperature
150°C
+5.5
168
Continuous Pdiss (T = 85°C)
(derate 17 mW/°C above 85°C)
1.10 W
Thermal Resistance
(channel to ground paddle)
59 °C/W
Storage Temperature
-65 to +150°C
Operating Temperature
-40 to +85°C
Downconverter will operate over full voltage range shown above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE.
4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE.
5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND.
6. CLASSIFIED AS MOISTURE SENSITIVITY LEVEL (MSL) 1.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC380QS16G
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC380QS16GE
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H380
XXXX
[2]
H380
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
8 - 66
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC380QS16G / 380QS16GE
v02.0305
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.7 - 2.2 GHz
Pin Descriptions
Pin Number
Function
Description
1, 3, 4, 7,
9, 14, 16
N/C
Not Connected
2
LO
This pin is AC coupled and matched to
50 Ohm from 1.4 - 2.2 GHz.
11, 12, 13
GND
Backside of package has exposed metal ground slug
that must also be connected to RF/DC ground.
5
Vdd LO
Power supply for the LO amplifier. One external RF
bypass capacitor (10,000 pF) is required.
6
Vdd IF
Bias voltage for IF amplifier. One external RF bypass
capacitor (10,000 pF) is required.
8
IF Bias
DC bias setting for IF amplifier.
10
IF
Output of IF and bias port for amplifier. A pull up inductor (L1), output matching network (C5, C6, L2), and
10,000 pF bypass capacitor (C4) are required.
15
RF
This pin is DC coupled and matched to
50 Ohm from 1.7 - 2.2 GHz.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
MIXERS - DOWNCONVERTERS - SMT
8
8 - 67
HMC380QS16G / 380QS16GE
v02.0305
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.7 - 2.2 GHz
Evaluation PCB
MIXERS - DOWNCONVERTERS - SMT
8
List of Materials for Evaluation PCB 106397 [1]
Item
Description
J1 - J3
PC Mount SMA RF Connector
J4 - J6
DC Pins
C1
1000 pF Chip Capacitor, 0603 Pkg.
C2, C3, C4
0.01μF Chip Capacitor, 0603 Pkg.
C5
82 pF Chip Capacitor, 0402 Pkg.
C6
6 pF Chip Capacitor, 0603 Pkg.
L1
150 nH Chip Inductor, 0805 Pkg.
L2
27 nH Chip Inductor, 0805 Pkg.
R1
3.3 Ohm Resistor, 0603 Pkg.
U1
HMC380QS16G / HMC380QS16GE
PCB [2]
104814 Evaluation Board, 1.100” x 1.100”
The circuit board used in the final application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
8 - 68
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC380QS16G / 380QS16GE
v02.0305
PCS/UMTS HIGH IP3 RFIC
DOWNCONVERTER, 1.7 - 2.2 GHz
Application Circuit
Note: Pin 5 and Pin 6 may be connected to a common Vdd Supply.
Selection of L2 & C6
For Various Tuned IF Frequencies*
IF
L2
C6
250 MHz
27 nH
6 pF
70 MHz
39 nH
39 pF
MIXERS - DOWNCONVERTERS - SMT
8
* Contact Hittite to optimize tuning topology for desired IF frequency.
* Unless otherwise noted all measurements with low side LO & IF = 250 MHz.
** If matching must be tuned for optimal results, see application circuit herein.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
8 - 69
Similar pages