Hittite HMC465LP5 Gaas phemt mmic modulator driver amplifier, dc - 20 ghz Datasheet

HMC465LP5 / 465LP5E
v06.1210
Amplifiers - Driver & Gain Block - SMT
8
GaAs PHEMT MMIC MODULATOR DRIVER
AMPLIFIER, DC - 20 GHz
Typical Applications
Features
The HMC465LP5(E) wideband driver is ideal for:
Gain: 15 dB
• OC192 LN/MZ Modulator Driver
Output Voltage to 10Vpk-pk
• Microwave Radio & VSAT
+24 dBm Saturated Output Power
• Test Instrumentation
Supply Voltage: +8V @160 mA
50 Ohm Matched Input/Output
• Military EW, ECM & C I
3
32 Lead 5x5 mm QFN Package: 25 mm2
Functional Diagram
General Description
The HMC465LP5(E) is a GaAs MMIC PHEMT Distributed Driver Amplifier packaged in leadless 5x5
mm surface mount package which operate between
DC and 20 GHz. The amplifier provides 15 dB of gain,
3 dB noise figure and +25 dBm of saturated output
power while requiring only 160 mA from a +8V supply.
Gain flatness is excellent at ±0.5 dB as well as ±4
deg deviation from linear phase from DC - 10 GHz
making the HMC465LP5(E) ideal for OC192 fiber
optic LN/MZ modulator driver amplifiers as well as
test equipment applications. The HMC465LP5(E)
amplifiers I/Os are internally matched to 50 Ohms.
Electrical Specifications, TA = +25° C, Vdd= 8V, Vgg2= 1.5V, Idd= 160 mA*
Parameter
Min.
Frequency Range
Gain
Typ.
Max.
Min.
DC - 6
13
±0.75
Gain Variation Over Temperature
0.015
Max.
Min.
6.0 - 12.0
16
Gain Flatness
Typ.
12
15
9.5
±0.25
0.02
0.020
Typ.
Max.
12.0 - 20.0
GHz
12.5
dB
±1.5
0.025
Units
0.035
dB
0.045
dB/ °C
Noise Figure
3.0
3.0
4.0
dB
Input Return Loss
20
15
8
dB
Output Return Loss
22
17
12
dB
Output Power for 1 dB Compression (P1dB)
20
dBm
25.5
25
23
dBm
Output Third Order Intercept (IP3)
32
28
24
dBm
Saturated Output Voltage
10
10
8
Vpk-pk
Group Delay Variation
±15
±15
Supply Current
(Idd) (Vdd= 8V, Vgg1= -0.6V Typ.)
160
160
Saturated Output Power (Psat)
21
24
20
23
16
pSec
160
mA
* Adjust Vgg1 between -2 to 0V to achieve Idd= 160 mA typical.
8-1
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC465LP5 / 465LP5E
GaAs PHEMT MMIC MODULATOR DRIVER
AMPLIFIER, DC - 20 GHz
Gain & Return Loss
Gain vs. Temperature
8
20
20
15
16
5
S21
S11
S22
0
GAIN (dB)
RESPONSE (dB)
10
-5
-10
12
+25C
+85C
-40C
8
-15
4
-20
-25
0
-30
0
2
4
6
8
10
12
14
16
18
20
0
22
2
4
6
FREQUENCY (GHz)
Input Return Loss vs. Temperature
12
14
16
18
20
22
0
+25C
+85C
-40C
-5
RETURN LOSS (dB)
-5
RETURN LOSS (dB)
10
Output Return Loss vs. Temperature
0
-10
-15
-20
-25
+25C
+85C
-40C
-10
-15
-20
-25
-30
-30
0
2
4
6
8
10
12
14
16
18
20
22
0
2
4
6
FREQUENCY (GHz)
10
12
14
16
18
20
18
20
22
Noise Figure vs. Temperature
25
10
9
15
NOISE FIGURE (dB)
8
5
S21
S11
S22
-5
-15
-25
+25C
+85C
-40C
7
6
5
4
3
2
-35
-45
0.00001
8
FREQUENCY (GHz)
Low Frequency Gain & Return Loss
RESPONSE (dB)
8
FREQUENCY (GHz)
Amplifiers - Driver & Gain Block - SMT
v06.1210
1
0
0.0001
0.001
0.01
0.1
FREQUENCY (GHz)
1
10
0
2
4
6
8
10
12
14
16
22
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-2
HMC465LP5 / 465LP5E
v03.1106
v06.1210
Psat vs. Temperature
30
30
26
26
Psat (dBm)
P1dB (dBm)
P1dB vs. Temperature
22
18
+25C
+85C
-40C
14
+25C
+85C
-40C
18
10
0
2
4
6
8
10
12
14
16
18
20
22
0
2
4
FREQUENCY (GHz)
38
36
IP3 (dBm)
34
32
30
28
26
+25C
+85C
-40C
20
18
0
2
4
6
8
10
12
14
16
18
20
22
Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
40
22
14
16
18
20
22
30
28
26
24
22
20
Gain
P1dB
18
Psat
IP3
16
14
12
10
7.5
8
8.5
Deviation from Linear Phase
DEVIATION FROM LINEAR PHASE (deg)
-200
-250
-300
-350
2
12
SUPPLY VOLTAGE (V)
Group Delay
1
10
32
FREQUENCY (GHz)
0
8
Gain, Power & Output IP3 vs. Supply
Voltage @ 10 GHz, Idd = 160mA
Output IP3 vs. Temperature
24
6
FREQUENCY (GHz)
-400
3
4
5
6
FREQUENCY (GHz)
8-3
22
14
10
GROUP DELAY (pSec)
Amplifiers - Driver & Gain Block - SMT
8
GaAs PHEMT MMIC MODULATOR DRIVER
AMPLIFIER, DC - 20 GHz
7
8
9
10
10
6
2
-2
-6
-10
0
2
4
6
8
10
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC465LP5 / 465LP5E
GaAs PHEMT MMIC MODULATOR DRIVER
AMPLIFIER, DC - 20 GHz
Absolute Maximum Ratings
Typical Supply Current vs. Vdd
Drain Bias Voltage (Vdd)
+9 Vdc
Vdd (V)
Idd (mA)
Gate Bias Voltage (Vgg1)
-2 to 0 Vdc
+7.5
161
+8.0
160
+8.5
159
Gate Bias Current (Igg1)
+3.2mA
Gate Bias Voltage (Vgg2)
(Vdd -8) Vdc to +3 Vdc
Gate Bias Current (Igg2)
+3.2mA
RF Input Power (RFIN)(Vdd = +8 Vdc)
+23 dBm
Channel Temperature
150 °C
Continuous Pdiss (T = 85 °C)
(derate 24 mW/°C above 85 °C)
1.56 W
Thermal Resistance
(channel to ground paddle)
41.5 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
8
Amplifiers - Driver & Gain Block - SMT
v06.1210
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC465LP5
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC465LP5E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
H465
XXXX
H465
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-4
HMC465LP5 / 465LP5E
v06.1210
Amplifiers - Driver & Gain Block - SMT
8
GaAs PHEMT MMIC MODULATOR DRIVER
AMPLIFIER, DC - 20 GHz
Pin Descriptions
Function
Description
1, 3, 4, 6 - 12, 14,
17, 18, 19, 20,
22 - 28, 31, 32
Pin Number
N/C
The pins are not connected internally; however, all data
shown herein was measured with these pins connected
to RF/DC ground externally.
2
Vgg2
Gate Control 2 for amplifier. +1.5V should
be applied to Vgg2 for nominal operation.
5
RFIN
This pad is DC coupled
and matched to 50 Ohms.
13
Vgg1
Gate Control 1 for amplifier.
15
ACG4
Interface Schematic
Low frequency termination. Attach bypass capacitor per
application circuit herein.
16
ACG3
21
RFOUT &
Vdd
RF output for amplifier. Connect the DC
bias (Vdd) network to provide drain current (Idd).
See application circuit herein.
29
ACG2
30
ACG1
Low frequency termination. Attach bypass capacitor per
application circuit herein.
Ground Paddle
GND
Ground paddle must be connected to RF/DC ground.
Application Circuit
NOTE 1: Drain Bias (Vdd) must be applied through a broadband bias tee or external bias network.
8-5
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC465LP5 / 465LP5E
GaAs PHEMT MMIC MODULATOR DRIVER
AMPLIFIER, DC - 20 GHz
Evaluation PCB
List of Materials for Evaluation PCB 108347
Item
Description
J1 - J2
SRI K Connector
J3 - J4
2mm Molex Header
C1, C2
100 pF Capacitor, 0402 Pkg.
C3 - C6
1000 pF Capacitor, 0603 Pkg.
C7 - C9
4.7 µF Capacitor, Tantalum
U1
HMC465LP5 / HMC465LP5E
PCB [2]
109765 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
8
[1]
The circuit board used in the final application
should use RF circuit design techniques. Signal
lines should have 50 Ohm impedance while the
package ground leads and package bottom should
be connected directly to the ground plane similar to
that shown. A sufficient number of via holes should
be used to connect the top and bottom ground
planes. The evaluation board should be mounted
to an appropriate heat sink. The evaluation circuit
board shown is available from Hittite upon request.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
Amplifiers - Driver & Gain Block - SMT
v06.1210
8-6
HMC465LP5 / 465LP5E
v06.1210
Amplifiers - Driver & Gain Block - SMT
8
8-7
GaAs PHEMT MMIC MODULATOR DRIVER
AMPLIFIER, DC - 20 GHz
Device Operation
These devices are susceptible to damage from Electrostatic Discharge. Proper precautions should be observed
during handling, assembly and test.
The input to this device should be AC-coupled. To provide the typical 8Vp-p output voltage swing, a 1.2Vp-p ACcoupled input voltage swing is required.
Device Power Up Instructions
1. Ground the device
2. Set Vgg to -2V (no drain current)
3. Set Vctl to +1V (no drain current)
4. Set Vdd to +5V (no drain current)
5. Adjust Vgg for Idd = 140mA
• Vgg may be varied between -1V and 0V to provide the desired eye crossing point percentage (i.e. 50% crosspoint)
and a limited cross point control capability.
• Vdd may be increased to +7V if required to achieve greater output voltage swing.
• Vctl may be adjusted between +2V and +0V to vary the output voltage swing.
Device Power Down Instructions
1. Reverse the sequence identified above in steps 1 through 4.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC465LP5 / 465LP5E
v06.1210
GaAs PHEMT MMIC MODULATOR DRIVER
AMPLIFIER, DC - 20 GHz
8
Amplifiers - Driver & Gain Block - SMT
Notes:
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
8-8
Similar pages