ON NCP1117DT285 1.0 a low-dropout positive fixed and adjustable voltage regulator Datasheet

NCP1117, NCV1117
1.0 A Low−Dropout Positive
Fixed and Adjustable
Voltage Regulators
The NCP1117 series are low dropout positive voltage regulators that
are capable of providing an output current that is in excess of 1.0 A
with a maximum dropout voltage of 1.2 V at 800 mA over
temperature. This series contains eight fixed output voltages of 1.5 V,
1.8 V, 2.0 V, 2.5 V, 2.85 V, 3.3 V, 5.0 V, and 12 V that have no
minimum load requirement to maintain regulation. Also included is an
adjustable output version that can be programmed from 1.25 V to
18.8 V with two external resistors. On chip trimming adjusts the
reference/output voltage to within ±1.0% accuracy. Internal protection
features consist of output current limiting, safe operating area
compensation, and thermal shutdown. The NCP1117 series can
operate with up to 20 V input. Devices are available in SOT−223 and
DPAK packages.
http://onsemi.com
Tab
1
123
3
(Top View)
Pin: 1. Adjust/Ground
2. Output
3. Input
Heatsink tab is connected to Pin 2.
Features
Tab
• Output Current in Excess of 1.0 A
• 1.2 V Maximum Dropout Voltage at 800 mA Over Temperature
• Fixed Output Voltages of 1.5 V, 1.8 V, 2.0 V, 2.5 V, 2.85 V, 3.3 V,
•
•
•
•
•
•
•
SOT−223
ST SUFFIX
CASE 318H
1
2
1 3
(Top View)
3
5.0 V, and 12 V
Adjustable Output Voltage Option
No Minimum Load Requirement for Fixed Voltage Output Devices
Reference/Output Voltage Trimmed to ±1.0%
Current Limit, Safe Operating and Thermal Shutdown Protection
Operation to 20 V Input
NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
Pb−Free Packages are Available
DPAK
DT SUFFIX
CASE 369C
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on pages 11 and 12 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 13 of this data sheet.
Applications
•
•
•
•
•
Consumer and Industrial Equipment Point of Regulation
Active SCSI Termination for 2.85 V Version
Switching Power Supply Post Regulation
Hard Drive Controllers
Battery Chargers
TYPICAL APPLICATIONS
110 Input
10
F
3
+
NCP1117
XTXX
Input
3
10
F
+
2 Output
+ 10
1
 Semiconductor Components Industries, LLC, 2004
3
2 Output
10
F
+ 10
1
F
4.75 V
to
5.25 V
F
Figure 1. Fixed
Output Regulator
July, 2004 − Rev. 11
NCP1117
XTA
Figure 2. Adjustable
Output Regulator
+
+
NCP1117
XT285
1
110 2
+ 22
F
110 18 to 27
Lines
110 Figure 3. Active SCSI Bus Terminator
1
Publication Order Number:
NCP1117/D
NCP1117, NCV1117
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Vin
20
V
−
Infinite
−
PD
RJA
RJC
Internally Limited
160
15
W
°C/W
°C/W
PD
RJA
RJC
Internally Limited
67
6.0
W
°C/W
°C/W
Maximum Die Junction Temperature Range
TJ
−55 to 150
°C
Storage Temperature Range
Tstg
−65 to 150
°C
Operating Ambient Temperature Range
NCP1117
NCV1117
TA
Input Voltage (Note 1)
Output Short Circuit Duration (Notes 2 and 3)
Power Dissipation and Thermal Characteristics
Case 318H (SOT−223)
Power Dissipation (Note 2)
Thermal Resistance, Junction−to−Ambient, Minimum Size Pad
Thermal Resistance, Junction−to−Case
Case 369A (DPAK)
Power Dissipation (Note 2)
Thermal Resistance, Junction−to−Ambient, Minimum Size Pad
Thermal Resistance, Junction−to−Case
°C
0 to +125
−40 to +125
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL−STD−883, Method 3015.
Machine Model Method 200 V.
2. Internal thermal shutdown protection limits the die temperature to approximately 175°C. Proper heatsinking is required to prevent activation.
The maximum package power dissipation is:
TJ(max) TA
PD RJA
3. The regulator output current must not exceed 1.0 A with Vin greater than 12 V.
http://onsemi.com
2
NCP1117, NCV1117
ELECTRICAL CHARACTERISTICS (Cin = 10 F, Cout = 10 F, for typical value TA = 25°C, for min and max values TA is the
operating ambient temperature range that applies unless otherwise noted. (Note 6)
Characteristic
Symbol
Reference Voltage, Adjustable Output Devices
(Vin–Vout = 2.0 V, Iout = 10 mA, TA = 25°C)
(Vin–Vout = 1.4 V to 10 V, Iout = 10 mA to 800 mA) (Note 6)
Vref
Output Voltage, Fixed Output Devices
Vout
Min
Typ
Max
1.238
1.225
1.25
−
1.262
1.270
Unit
V
V
1.5 V
(Vin = 3.5 V, Iout = 10 mA, TA = 25 °C)
(Vin = 2.9 V to 11.5 V, Iout = 0 mA to 800 mA) (Note 6)
1.485
1.470
1.500
−
1.515
1.530
1.8 V
(Vin = 3.8 V, Iout = 10 mA, TA = 25 °C)
(Vin = 3.2 V to 11.8 V, Iout = 0 mA to 800 mA) (Note 6)
1.782
1.755
1.800
−
1.818
1.845
2.0 V
(Vin = 4.0 V, Iout = 10 mA, TA = 25 °C)
(Vin = 3.4 V to 12 V, Iout = 0 mA to 800 mA) (Note 6)
1.970
1.960
2.000
−
2.030
2.040
2.5 V
(Vin = 4.5 V, Iout = 10 mA, TA = 25 °C)
(Vin = 3.9 V to 10 V, Iout = 0 mA to 800 mA,) (Note 6)
2.475
2.450
2.500
−
2.525
2.550
2.85 V (Vin = 4.85 V, Iout = 10 mA, TA = 25 °C)
(Vin = 4.25 V to 10 V, Iout = 0 mA to 800 mA) (Note 6)
(Vin = 4.0 V, Iout = 0 mA to 500 mA) (Note 6)
2.821
2.790
2.790
2.850
−
−
2.879
2.910
2.910
3.3 V
(Vin = 5.3 V, Iout = 10 mA, TA = 25 °C)
(Vin = 4.75 V to 10 V, Iout = 0 mA to 800 mA) (Note 6)
3.267
3.235
3.300
−
3.333
3.365
5.0 V
(Vin = 7.0 V, Iout = 10 mA, TA = 25 °C)
(Vin = 6.5 V to 12 V, Iout = 0 mA to 800 mA) (Note 6)
4.950
4.900
5.000
−
5.050
5.100
12 V
(Vin = 14 V, Iout = 10 mA, TA = 25 °C)
(Vin = 13.5 V to 20 V, Iout = 0 mA to 800 mA) (Note 6)
11.880
11.760
12.000
−
12.120
12.240
−
0.04
0.1
%
−
−
−
−
−
−
−
−
0.3
0.4
0.5
0.5
0.8
0.8
0.9
1.0
1.0
1.0
2.5
2.5
3.0
4.5
6.0
7.5
mV
−
0.2
0.4
%
−
−
−
−
−
−
−
−
2.3
2.6
3.0
3.3
3.8
4.3
6.7
16
5.5
6.0
6.0
7.5
8.0
10
15
28
−
−
−
0.95
1.01
1.07
1.10
1.15
1.20
1000
1500
2200
Line Regulation (Note 4)
Adjustable (Vin = 2.75 V to 16.25 V, Iout = 10 mA)
1.5 V
1.8 V
2.0 V
2.5 V
2.85 V
3.3 V
5.0 V
12 V
Regline
(Vin = 2.9 V to 11.5 V, Iout = 0 mA)
(Vin = 3.2 V to 11.8 V, Iout = 0 mA)
(Vin = 3.4 V to 12 V, Iout = 0 mA)
(Vin = 3.9 V to 10 V, Iout = 0 mA)
(Vin = 4.25 V to 10 V, Iout = 0 mA)
(Vin = 4.75 V to 15 V, Iout = 0 mA)
(Vin = 6.5 V to 15 V, Iout = 0 mA)
(Vin = 13.5 V to 20 V, Iout = 0 mA)
Load Regulation (Note 4)
Adjustable (Iout = 10 mA to 800 mA, Vin = 4.25 V)
1.5 V
1.8 V
2.0 V
2.5 V
2.85 V
3.3 V
5.0 V
12 V
Regline
(Iout = 0 mA to 800 mA, Vin = 2.9 V)
(Iout = 0 mA to 800 mA, Vin = 3.2 V)
(Iout = 0 mA to 800 mA, Vin = 3.4 V)
(Iout = 0 mA to 800 mA, Vin = 3.9 V)
(Iout = 0 mA to 800 mA, Vin = 4.25 V)
(Iout = 0 mA to 800 mA, Vin = 4.75 V)
(Iout = 0 mA to 800 mA, Vin = 6.5 V)
(Iout = 0 mA to 800 mA, Vin = 13.5 V)
Dropout Voltage (Measured at Vout − 100 mV)
(Iout = 100 mA)
(Iout = 500 mA)
(Iout = 800 mA)
Vin−Vout
Output Current Limit (Vin−Vout = 5.0 V, TA = 25°C, Note 5)
Iout
V
4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
5. The regulator output current must not exceed 1.0 A with Vin greater than 12 V.
6. NCP1117: Tlow = 0°C , Thigh = 125°C
NCV1117: Tlow = −40°C, Thigh = 125°C
http://onsemi.com
3
mV
mA
NCP1117, NCV1117
ELECTRICAL CHARACTERISTICS (Cin = 10 F, Cout = 10 F, for typical value TA = 25°C, for min and max values TA is the
operating ambient temperature range that applies unless otherwise noted. (Note 7)
Characteristic
Minimum Required Load Current for Regulation, Adjustable Output Devices
(Vin = 15 V)
Quiescent Current
1.5 V (Vin = 11.5 V)
1.8 V (Vin = 11.8 V)
2.0 V (Vin = 12 V)
2.5 V (Vin = 10 V)
2.85 V (Vin = 10 V)
3.3 V (Vin = 15 V)
5.0 V (Vin = 15 V)
12 V
(Vin = 20 V)
Symbol
Min
Typ
Max
Unit
IL(min)
−
0.8
5.0
mA
−
−
−
−
−
−
−
−
3.6
4.2
4.5
5.2
5.5
6.0
6.0
6.0
10
10
10
10
10
10
10
10
−
0.01
0.1
67
66
64
64
62
62
60
57
50
73
72
70
70
68
68
64
61
54
−
−
−
−
−
−
−
−
−
IQ
Thermal Regulation (TA = 25°C, 30 ms Pulse)
mA
%/W
Ripple Rejection (Vin−Vout = 6.4 V, Iout = 500 mA, 10 Vpp 120 Hz Sinewave)
Adjustable
1.5 V
1.8 V
2.0 V
2.5 V
2.85 V
3.3 V
5.0 V
12 V
RR
Adjustment Pin Current (Vin = 11.25 V, Iout = 800 mA)
Iadj
−
52
120
A
Adjust Pin Current Change
(Vin−Vout = 1.4 V to 10 V, Iout = 10 mA to 800 mA)
Iadj
−
0.4
5.0
A
Temperature Stability
ST
−
0.5
−
%
Long Term Stability (TA = 25°C, 1000 Hrs End Point Measurement)
St
−
0.3
−
%
RMS Output Noise (f = 10 Hz to 10 kHz)
N
−
0.003
−
%Vout
7. NCP1117: Tlow = 0°C , Thigh = 125°C
NCV1117: Tlow = −40°C, Thigh = 125°C
http://onsemi.com
4
dB
1.4
2.0
Vin = Vout + 3.0 V
Iout = 10 mA
1.5
Vin − Vout, DROPOUT VOLTAGE (V)
Vout, OUTPUT VOLTAGE CHANGE (%)
NCP1117, NCV1117
Adj, 1.5 V,
1.8 V, 2.0 V,
2.5 V
1.0
0.5
0
−0.5
2.85 V, 3.3 V,
5.0 V, 12.0 V
−1.0
−1.5
−2.0
−50
−25
0
25
50
75
100
TJ = −40°C
1.0
0.8
TJ = 125°C
0.6
0.4
0.2
Load pulsed at 1.0% duty cycle
0
150
125
TJ = 25°C
1.2
0
200
400
600
800
TA, AMBIENT TEMPERATURE (°C)
Iout, OUTPUT CURRENT (mA)
Figure 4. Output Voltage Change
vs. Temperature
Figure 5. Dropout Voltage
vs. Output Current
1000
2.0
2.0
Iout, OUTPUT CURRENT (A)
Iout, OUTPUT CURRENT (A)
TJ = 25°C
1.5
1.0
0.5
1.8
1.6
1.4
1.2
Vin = 5.0 V
Load pulsed at 1.0% duty cycle
Load pulsed at 1.0% duty cycle
0
2
4
6
8
10
12
14
16
18
1.0
−50
20
0
25
50
75
100
125
TA, AMBIENT TEMPERATURE (°C)
Figure 6. Output Short Circuit Current
vs. Differential Voltage
Figure 7. Output Short Circuit Current
vs. Temperature
100
Iadj, ADJUST PIN CURRENT (A)
−25
Vin − Vout, VOLTAGE DIFFERENTIAL (V)
IQ, QUIESCENT CURRENT CHANGE (%)
0
80
60
150
10
5.0
0
−5.0
40
20
0
−50
Iout = 10 mA
−25
0
25
50
75
100
125
150
−10
−15
−20
−50
−25
0
25
50
75
100
125
TA, AMBIENT TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 8. Adjust Pin Current
vs. Temperature
Figure 9. Quiescent Current Change
vs. Temperature
http://onsemi.com
5
150
NCP1117, NCV1117
100
fripple = 120 Hz
Vripple 3.0 VP−P
80
60
RR, RIPPLE REJECTION (dB)
RR, RIPPLE REJECTION (dB)
100
fripple = 20 kHz
Vripple 0.5 VP−P
40
Vout = 5.0 V
Vin − Vout = 3.0 V
Cout = 10 F
Cadj = 25 F
TA = 25°C
20
0
Vin − Vout 3.0 V
80
60
Vout = 5.0 V
Vin − Vout = 3.0 V
Iout = 0.5 A
Cout = 10 F
Cadj = 25 F, f > 60 Hz
Cadj = 200 F, f 60 Hz
TA = 25°C
40
20
400
600
800
1000
Vin − Vout Vdropout
100
1.0 k
10 k
100 k
Figure 10. NCP1117XTA Ripple Rejection
vs. Output Current
Figure 11. NCP1117XTA Ripple Rejection
vs. Frequency
OUTPUT VOLTAGE
DEVIATION (V)
fripple, RIPPLE FREQUENCY (Hz)
Cin = 1.0 F
Cout = 10 F
Iout = 0.1 A
TA = 25°C
5.25
0.1
0
20
0
−20
80
120
160
0.5
0
200
0
40
80
120
t, TIME (s)
Figure 12. NCP1117XT285
Line Transient Response
Figure 13. NCP1117XT285
Load Transient Response
Cin = 1.0 F
Cout = 10 F
Iout = 0.1 A
TA = 25°C
7.5
20
0
−20
80
120
160
200
0
Cin = 10 F
Cout = 10 F
Vin = 6.5 V
Preload = 0.1 A
TA = 25°C
0.5
0
0
t, TIME (s)
40
80
120
160
t, TIME (s)
Figure 14. NCP1117XT50
Line Transient Response
Figure 15. NCP1117XT50
Load Transient Response
http://onsemi.com
6
200
0.1
−0.1
6.5
40
160
t, TIME (s)
OUTPUT VOLTAGE
DEVIATION (V)
40
Cin = 10 F
Cout = 10 F
Vin = 4.5 V
Preload = 0.1 A
TA = 25°C
−0.1
LOAD CURRENT
CHANGE (A)
4.25
0
10
Iout, OUTPUT CURRENT (mA)
LOAD CURRENT
CHANGE (A)
INPUT
VOLTAGE (V)
OUTPUT VOLTAGE
DEVIATION (mV)
200
0
INPUT
VOLTAGE (V)
Vripple 0.5 VP−P
0
0
OUTPUT VOLTAGE
DEVIATION (mV)
Vripple 3.0 VP−P
200
OUTPUT VOLTAGE
DEVIATION (V)
Cin = 1.0 F
Cout = 10 F
Iout = 0.1 A
TA = 25°C
14.5
0.1
0
Cin = 10 F
Cout = 10 F
Vin = 13.5 V
Preload = 0.1 A
TA = 25°C
−0.1
LOAD CURRENT
CHANGE (A)
13.5
20
0
−20
120
160
200
0
0
40
80
t, TIME (s)
Figure 17. NCP1117XT12 Load
Transient Response
180
1.6
160
1.4
PD(max) for TA = 50°C
140
ÎÎÎ
ÎÎÎ
ÎÎÎ
2.0 oz. Copper
L
Minimum
Size Pad
L
100
80
1.2
1.0
0.8
0.6
RJA
60
0
5.0
10
15
20
25
L, LENGTH OF COPPER (mm)
0.4
30
Figure 18. SOT−223 Thermal Resistance and Maximum
Power Dissipation vs. P.C.B. Copper Length
1.6
100
PD(max) for TA = 50°C
1.4
90
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
2.0 oz. Copper
L
80
Minimum
Size Pad
70
1.2
1.0
L
0.8
60
50
0.6
RJA
40
0
160
t, TIME (s)
Figure 16. NCP1117XT12 Line
Transient Response
120
120
PD, MAXIMUM POWER DISSIPATION (W)
80
0.5
5.0
10
15
20
25
0.4
30
L, LENGTH OF COPPER (mm)
Figure 19. DPAK Thermal Resistance and Maximum
Power Dissipation vs. P.C.B. Copper Length
http://onsemi.com
7
PD, MAXIMUM POWER DISSIPATION (W)
40
RJA, THERMAL RESISTANCE,
JUNCTION−TO−AIR (°CW)
0
RJA, THERMAL RESISTANCE,
JUNCTION−TO−AIR (°CW)
OUTPUT VOLTAGE
DEVIATION (mV)
INPUT
VOLTAGE (V)
NCP1117, NCV1117
200
NCP1117, NCV1117
APPLICATIONS INFORMATION
Introduction
Frequency compensation for the regulator is provided by
capacitor Cout and its use is mandatory to ensure output
stability. A minimum capacitance value of 4.7 F with an
equivalent series resistance (ESR) that is within the limits of
0.25 to 2.2 is required. The capacitor type can be
ceramic, tantalum, or aluminum electrolytic as long as it
meets the minimum capacitance value and ESR limits over
the circuit’s entire operating temperature range. Higher
values of output capacitance can be used to enhance loop
stability and transient response with the additional benefit of
reducing output noise.
The NCP1117 features a significant reduction in dropout
voltage along with enhanced output voltage accuracy and
temperature stability when compared to older industry
standard three−terminal adjustable regulators. These
devices contain output current limiting, safe operating area
compensation and thermal shutdown protection making
them designer friendly for powering numerous consumer
and industrial products. The NCP1117 series is pin
compatible with the older LM317 and its derivative device
types.
Output Voltage
Input
The typical application circuits for the fixed and
adjustable output regulators are shown in Figures 20 and 21.
The adjustable devices are floating voltage regulators. They
develop and maintain the nominal 1.25 V reference voltage
between the output and adjust pins. The reference voltage is
programmed to a constant current source by resistor R1, and
this current flows through R2 to ground to set the output
voltage. The programmed current level is usually selected to
be greater than the specified 5.0 mA minimum that is
required for regulation. Since the adjust pin current, Iadj, is
significantly lower and constant with respect to the
programmed load current, it generates a small output
voltage error that can usually be ignored. For the fixed
output devices R1 and R2 are included within the device and
the ground current Ignd, ranges from 3.0 mA to 5.0 mA
depending upon the output voltage.
Cin
Cin
+
NCP1117
XTXX
1
+
R1
Vref
1
+
+
Cout
Cadj
Vout Vref 1 R2 Iadj R2
R1
Figure 21. Adjustable Output Regulator
The output ripple will increase linearly for fixed and
adjustable devices as the ratio of output voltage to the
reference voltage increases. For example, with a 12 V
regulator, the output ripple will increase by 12 V/1.25 V or
9.6 and the ripple rejection will decrease by 20 log of this
ratio or 19.6 dB. The loss of ripple rejection can be restored
to the values shown with the addition of bypass capacitor
Cadj, shown in Figure 21. The reactance of Cadj at the ripple
frequency must be less than the resistance of R1. The value
of R1 can be selected to provide the minimum required load
current to maintain regulation and is usually in the range of
100 to 200 .
Cadj 1
2 fripple R1
The minimum required capacitance can be calculated
from the above formula. When using the device in an
application that is powered from the AC line via a
transformer and a full wave bridge, the value for Cadj is:
Output
2
Output
2
R2
Input bypass capacitor Cin may be required for regulator
stability if the device is located more than a few inches from
the power source. This capacitor will reduce the circuit’s
sensitivity when powered from a complex source impedance
and significantly enhance the output transient response. The
input bypass capacitor should be mounted with the shortest
possible track length directly across the regulator’s input
and ground terminals. A 10 F ceramic or tantalum
capacitor should be adequate for most applications.
3
+
NCP1117
XTA
Iadj
External Capacitors
Input
3
fripple 120 Hz, R1 120 , then Cadj 11.1 F
The value for Cadj is significantly reduced in applications
where the input ripple frequency is high. If used as a post
regulator in a switching converter under the following
conditions:
Cout
Ignd
fripple 50 kHz, R1 120 , then Cadj 0.027 F
Figure 20. Fixed Output Regulator
Figures 10 and 11 shows the level of ripple rejection that
is obtainable with the adjust pin properly bypassed.
http://onsemi.com
8
NCP1117, NCV1117
Protection Diodes
The second condition is that the ground end of R2 should be
connected directly to the load. This allows true Kelvin
sensing where the regulator compensates for the voltage
drop caused by wiring resistance RW −.
The NCP1117 family has two internal low impedance
diode paths that normally do not require protection when
used in the typical regulator applications. The first path
connects between Vout and Vin, and it can withstand a peak
surge current of about 15 A. Normal cycling of Vin cannot
generate a current surge of this magnitude. Only when Vin
is shorted or crowbarred to ground and Cout is greater than
50 F, it becomes possible for device damage to occur.
Under these conditions, diode D1 is required to protect the
device. The second path connects between Cadj and Vout, and
it can withstand a peak surge current of about 150 mA.
Protection diode D2 is required if the output is shorted or
crowbarred to ground and Cadj is greater than 1.0 F.
Input
Cin
3
+
NCP1117
XTA
RW+
2
+
R1
1
Cout
Output
Remote
Load
R2
RW−
Figure 23. Load Sensing
D1
Thermal Considerations
1N4001
Input
Cin
3
+
NCP1117
XTA
1
R1
+
R2
This series contains an internal thermal limiting circuit
that is designed to protect the regulator in the event that the
maximum junction temperature is exceeded. When
activated, typically at 175°C, the regulator output switches
off and then back on as the die cools. As a result, if the device
is continuously operated in an overheated condition, the
output will appear to be oscillating. This feature provides
protection from a catastrophic device failure due to
accidental overheating. It is not intended to be used as a
substitute for proper heatsinking. The maximum device
power dissipation can be calculated by:
Output
2
D2
1N4001
+
Cout
Cadj
Figure 22. Protection Diode Placement
A combination of protection diodes D1 and D2 may be
required in the event that Vin is shorted to ground and Cadj
is greater than 50 F. The peak current capability stated for
the internal diodes are for a time of 100 s with a junction
temperature of 25°C. These values may vary and are to be
used as a general guide.
PD TJ(max) TA
RJA
The devices are available in surface mount SOT−223 and
DPAK packages. Each package has an exposed metal tab
that is specifically designed to reduce the junction to air
thermal resistance, RJA, by utilizing the printed circuit
board copper as a heat dissipater. Figures 18 and 19 show
typical RJA values that can be obtained from a square
pattern using economical single sided 2.0 ounce copper
board material. The final product thermal limits should be
tested and quantified in order to insure acceptable
performance and reliability. The actual RJA can vary
considerably from the graphs shown. This will be due to any
changes made in the copper aspect ratio of the final layout,
adjacent heat sources, and air flow.
Load Regulation
The NCP1117 series is capable of providing excellent
load regulation; but since these are three terminal devices,
only partial remote load sensing is possible. There are two
conditions that must be met to achieve the maximum
available load regulation performance. The first is that the
top side of programming resistor R1 should be connected as
close to the regulator case as practicable. This will minimize
the voltage drop caused by wiring resistance RW + from
appearing in series with reference voltage that is across R1.
http://onsemi.com
9
NCP1117, NCV1117
Input
NCP1117
XTA
3
+
10
F
Constant Current
Output
R
2
+
1
Input
+
10
F
10
F
NCP1117
XTA
3
Output
2
+
R1
1
50 k
R2
2N2907
Figure 25. Slow Turn−On Regulator
Input
3
10
F
+
NCP1117
XTA
+
Output
2
+
R1
1
10
F
Output
2
+ 10
120
1
NCP1117
XTA
3
10
F
Input
10
F
10
F
V
Iout ref Iadj
R
Figure 24. Constant Current Regulator
1N4001
R2
F
2N2222
360
1.0 k
Output Control
2N2222
On
1.0 k
Off
Output Voltage Control
Resistor R2 sets the maximum output voltage. Each
transistor reduces the output voltage when turned on.
Vout(Off) Vref
Figure 26. Regulator with Shutdown
Input
3
10
F
+
NCP1117
XT50
2
Figure 27. Digitally Controlled Regulator
Output
+ 10
F
1
50 Input
5.3 V AC Line
5.0 V Battery
RCHG
3
+
6.6 V
−
10
F
+
NCP1117
XT50
10
F
2
3
+
NCP1117
XT50
Output
5.0 V to
12 V
+ 10
2
F
1
+ 10
2.0 k
1
F
The 50 resistor that is in series with the ground pin of the
upper regulator level shifts its output 300 mV higher than the
lower regulator. This keeps the lower regulator off until the
input source is removed.
Figure 28. Battery Backed−Up Power Supply
Figure 29. Adjusting Output of Fixed
Voltage Regulators
http://onsemi.com
10
NCP1117, NCV1117
ORDERING INFORMATION
Nominal Output
Voltage
Package
Shipping†
NCP1117DTA
Adjustable
DPAK
75 Units / Rail
NCP1117DTAG
Adjustable
DPAK
(Pb−Free)
75 Units / Rail
NCP1117DTARK
Adjustable
DPAK
2500 / Tape & Reel
NCP1117DTARKG
Adjustable
DPAK
(Pb−Free)
2500 / Tape & Reel
NCP1117DTAT5
Adjustable
DPAK
2500 / Tape & Reel
NCP1117STAT3
Adjustable
SOT−223
4000 / Tape & Reel
NCP1117STAT3G
Adjustable
SOT−223
(Pb−Free)
4000 / Tape & Reel
NCP1117DT12
12
DPAK
75 Units / Rail
NCP1117DT12RK
12
DPAK
2500 / Tape & Reel
NCP1117DT12T3
12
SOT−223
4000 / Tape & Reel
NCP1117DT15
1.5
DPAK
75 Units / Rail
NCP1117DT15RK
1.5
DPAK
2500 / Tape & Reel
NCP1117DT15RKG
1.5
DPAK
(Pb−Free)
2500 / Tape & Reel
NCP1117ST15T3
1.5
SOT−223
4000 / Tape & Reel
NCP1117ST15T3G
1.5
SOT−223
(Pb−Free)
4000 / Tape & Reel
NCP1117DT18
1.8
DPAK
75 Units / Rail
NCP1117DT18RK
1.8
DPAK
2500 / Tape & Reel
NCP1117DT18RKG
1.8
DPAK
(Pb−Free)
2500 / Tape & Reel
NCP1117DT18T5
1.8
DPAK
2500 / Tape & Reel
NCP1117DT18T5G
1.8
DPAK
(Pb−Free)
2500 / Tape & Reel
NCP1117ST18T3
1.8
SOT−223
4000 / Tape & Reel
NCP1117ST18T3G
1.8
SOT−223
(Pb−Free)
4000 / Tape & Reel
NCP1117DT20
2.0
DPAK
75 Units / Rail
NCP1117DT20RK
2.0
DPAK
2500 / Tape & Reel
NCP1117ST20T3
2.0
SOT−223
4000 / Tape & Reel
NCP1117ST20T3G
2.0
SOT−223
(Pb−Free)
4000 / Tape & Reel
NCP1117DT25
2.5
DPAK
75 Units / Rail
NCP1117DT25RK
2.5
DPAK
2500 / Tape & Reel
NCP1117DT25RKG
2.5
DPAK
(Pb−Free)
2500 / Tape & Reel
NCP1117DT25T5
2.5
DPAK
2500 / Tape & Reel
NCP1117ST25T3
2.5
SOT−223
4000 / Tape & Reel
NCP1117ST25T3G
2.5
SOT−223
(Pb−Free)
4000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV prefix is for automotive and other applications requiring site and control changes.
http://onsemi.com
11
NCP1117, NCV1117
ORDERING INFORMATION
Nominal Output
Voltage
Package
Shipping†
NCP1117DT285
2.85
DPAK
75 Units / Rail
NCP1117DT285RK
2.85
DPAK
2500 / Tape & Reel
NCP1117ST285T3
2.85
SOT−223
4000 / Tape & Reel
NCP1117DT33
3.3
DPAK
75 Units / Rail
NCP1117DT33RK
3.3
DPAK
2500 / Tape & Reel
NCP1117DT33RKG
3.3
DPAK
(Pb−Free)
2500 / Tape & Reel
NCP1117DT33T5
3.3
DPAK
2500 /Tape & Reel
NCP1117DT33T5G
3.3
DPAK
(Pb−Free)
2500 /Tape & Reel
NCP1117ST33T3
3.3
SOT−223
4000 /Tape & Reel
NCP1117ST33T3G
3.3
SOT−223
(Pb−Free)
4000 /Tape & Reel
NCP1117DT50
5.0
DPAK
75 Units/Rail
NCP1117DT50RK
5.0
DPAK
2500 / Tape & Reel
NCP1117DT50RKG
5.0
DPAK
(Pb−Free)
2500 / Tape & Reel
NCP1117ST50T3
5.0
SOT−223
4000 /Tape & Reel
NCV1117DTARK*
Adjustable
DPAK
2500 / Tape & Reel
NCV1117STAT3*
Adjustable
SOT−223
4000 / Tape & Reel
NCV1117STAT3G*
Adjustable
SOT−223
(Pb−Free)
4000 / Tape & Reel
NCV1117ST12T3*
12
SOT−223
4000 / Tape & Reel
NCV1117ST12T3G*
12
SOT−223
(Pb−Free)
4000 / Tape & Reel
NCV1117DT15RK*
1.5
DPAK
2500 / Tape & Reel
NCV1117DT15RKG*
1.5
DPAK
(Pb−Free)
2500 / Tape & Reel
NCV1117ST15T3*
1.5
SOT−223
4000 / Tape & Reel
NCV1117DT18T5*
1.8
DPAK
2500 / Tape & Reel
NCV1117DT25RK*
2.5
DPAK
2500 / Tape & Reel
NCV1117ST25T3*
2.5
SOT−223
4000 / Tape & Reel
NCV1117DT33T5*
3.3
DPAK
2500 / Tape & Reel
NCV1117DT50RK*
5.0
DPAK
2500 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
*NCV prefix is for automotive and other applications requiring site and control changes.
http://onsemi.com
12
NCP1117, NCV1117
MARKING DIAGRAMS
SOT−223
ST SUFFIX
CASE 318H
ALYW
117−A
1
2
ALYW
17−15
1
3
Adjustable
2
ALYW
17−18
1
3
1.5 V
2
1
3
1.8 V
1
3
2.85 V
2
2
ALYW
17−25
1
3
2.0 V
ALYW
17−33
ALYW
7−285
1
2
ALYW
117−2
1
3.3 V
2
3
2.5 V
ALYW
117−5
3
2
ALYW
17−12
1
3
5.0 V
2
3
12 V
DPAK
DT SUFFIX
CASE 369C
117AJ
ALYWW
17−15
ALYWW
2
1
17−18
ALYWW
2
3
1
Adjustable
2
3
1
1.5 V
17285
ALYWW
17−33
ALYWW
1
2.85 V
1
2
3
1
2.0 V
117−5
ALYWW
2
3
17−25
ALYWW
2
3
1.8 V
2
1
117−2
ALYWW
2.5 V
17−12
ALYWW
2
3
1
3.3 V
A
L
Y
WW, W
2
3
5.0 V
= Assembly Location
= Wafer Lot
= Year
= Work Week
http://onsemi.com
13
3
1
3
12 V
NCP1117, NCV1117
PACKAGE DIMENSIONS
SOT−223
ST SUFFIX
CASE 318H−01
ISSUE O
0.08
E
0.2
C B
M
S
C
B
S
H
e
M
0.1
B
0.1
M
C A
S
B
S
A
e1
b
D
2
A
4
b2
S
3
A
C A
B
1
E1
A1
A
B
ÉÉÉÉÉÉÉ
ÇÇÇÇÇÇ
ÉÉÉÉÉÉÉ
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSION E1 DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.23 PER
SIDE.
4. DIMENSIONS b AND b2 DO NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 TOTAL IN EXCESS
OF THE b AND b2 DIMENSIONS AT MAXIMUM
MATERIAL CONDITION.
5. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
6. DIMENSIONS D AND E1 ARE TO BE DETERMINED
AT DATUM PLANE H.
ÉÉ
ÇÇ
ÉÉ
(b)
(b2)
c1
c
b1
b3
SECTION B−B
L
SECTION A−A
DIM
A
A1
b
b1
b2
b3
c
c1
D
E
E1
e
e1
L
SOLDERING FOOTPRINT*
3.8
0.15
2.0
0.079
2.3
0.091
2.3
0.091
6.3
0.248
2.0
0.079
1.5
0.059
SCALE 6:1
mm
inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
14
MILLIMETERS
MIN
MAX
−−−
1.80
0.02
0.11
0.60
0.88
0.60
0.80
2.90
3.10
2.90
3.05
0.24
0.35
0.24
0.30
6.30
6.70
6.70
7.30
3.30
3.70
2.30
4.60
−−−
0.25
0
10
NCP1117, NCV1117
PACKAGE DIMENSIONS
DPAK
DT SUFFIX
CASE 369C−01
ISSUE O
C
B
V
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
SEATING
PLANE
−T−
E
R
4
Z
A
S
1
2
DIM
A
B
C
D
E
F
G
H
J
K
L
R
S
U
V
Z
3
U
K
F
J
L
H
D
G
2 PL
0.13 (0.005)
M
T
SOLDERING FOOTPRINT*
6.20
0.244
3.0
0.118
2.58
0.101
5.80
0.228
1.6
0.063
6.172
0.243
SCALE 3:1
mm
inches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
15
INCHES
MIN
MAX
0.235 0.245
0.250 0.265
0.086 0.094
0.027 0.035
0.018 0.023
0.037 0.045
0.180 BSC
0.034 0.040
0.018 0.023
0.102 0.114
0.090 BSC
0.180 0.215
0.025 0.040
0.020
−−−
0.035 0.050
0.155
−−−
MILLIMETERS
MIN
MAX
5.97
6.22
6.35
6.73
2.19
2.38
0.69
0.88
0.46
0.58
0.94
1.14
4.58 BSC
0.87
1.01
0.46
0.58
2.60
2.89
2.29 BSC
4.57
5.45
0.63
1.01
0.51
−−−
0.89
1.27
3.93
−−−
NCP1117, NCV1117
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
16
For additional information, please contact your
local Sales Representative.
NCP1117/D
Similar pages