ON MC10EL05 2-input differential and/nand Datasheet

SEMICONDUCTOR TECHNICAL DATA
The MC10EL/100EL05 is a 2-input differential AND/NAND gate. The
device is functionally equivalent to the E404 device with higher
performance capabilities. With propagation delays and output transition
times significantly faster than the E404 the EL05 is ideally suited for those
applications which require the ultimate in AC performance.
Because a negative 2-input NAND is equivalent to a 2-input OR
function, the differential inputs and outputs of the device allows the EL05
to also be used as a 2-input differential OR/NOR gate.
The differential inputs employ clamp circuitry so that under open input
conditions (pulled down to VEE) the input to the AND gate will be HIGH. In
this way, if one set of inputs is open, the gate will remain active to the
other input.
8
1
•
•
•
•
275ps Propagation Delay
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751-05
High Bandwidth Output Transitions
75kΩ Internal Input Pulldown Resistors
>1000V ESD Protection
LOGIC DIAGRAM AND PINOUT ASSIGNMENT
D0 1
8 VCC
D0 2
7 Q
D1 3
6 Q
D1 4
PIN DESCRIPTION
PIN
FUNCTION
D0, D1
Q
Data Inputs
Data Outputs
5 VEE
12/93
 Motorola, Inc. 1996
3–1
REV 2
MC10EL05 MC100EL05
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND)
–40°C
Symbol
IEE
VEE
IIH
Characteristic
Min
Power Supply Current
10EL
100EL
Power Supply Voltage
10EL
100EL
–4.75
–4.20
0°C
Typ
Max
18
18
22
22
–5.2
–4.5
–5.5
–5.5
Input HIGH Current
Min
–4.75
–4.20
25°C
Typ
Max
18
18
22
22
–5.2
–4.5
–5.5
–5.5
150
Min
–4.75
–4.20
85°C
Typ
Max
18
18
22
22
–5.2
–4.5
–5.5
–5.5
150
Min
–4.75
–4.20
Typ
Max
Unit
18
21
22
25
mA
–5.2
–4.5
–5.5
–5.5
V
150
µA
150
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND)
–40°C
Symbol
Characteristic
0°C
25°C
85°C
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
260
440
185
275
390
185
275
390
215
305
420
ps
tPLH
tPHL
Propagation Delay to
Output
135
VPP
Minimum Input Swing1
150
VCMR
Common Mode Range2
–0.4
tr
tf
Output Rise/Fall Times Q
(20% – 80%)
100
150
225
See2
–0.4
350
100
150
225
See2
–0.4
350
100
150
225
See2
–0.4
350
100
mV
225
See2
V
350
ps
1. Minimum input swing for which AC parameters are guaranteed. The device has a DC gain of ≈40.
2. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within
the specified range and the peak-to-peak voltage lies between VPPmin and 1V. The lower end of the CMR range is dependent on VEE and is
equal to VEE + 3.0V.
MOTOROLA
3–2
ECLinPS and ECLinPS Lite
DL140 — Rev 3
MC10EL05 MC100EL05
OUTLINE DIMENSIONS
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751–05
ISSUE P
–A–
M
1
4
R
0.25 (0.010)
4X
–B–
X 45 _
B
M
5
P
8
NOTES:
1. DIMENSIONS A AND B ARE DATUMS AND T IS A
DATUM SURFACE.
2. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
3. DIMENSIONS ARE IN MILLIMETER.
4. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.
5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
6. DIMENSION D DOES NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE D DIMENSION AT MAXIMUM MATERIAL
CONDITION.
J
M_
C
F
G
–T–
K
SEATING
PLANE
8X
D
0.25 (0.010)
M
T B
S
A
S
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.18
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
◊
ECLinPS and ECLinPS Lite
DL140 — Rev 3
3–3
*MC10EL05/D*
MC10EL05/D
MOTOROLA
Similar pages