PCA EPA249G-7 8 pin triple ttl compatible active delay line Datasheet

8 Pin Triple TTL Compatible Active Delay Lines
Delay Time
±5% or
±2nS†
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
DIP Part
Number
SMD-G Part
Number
SMD-J Part
Number
EPA249-5
EPA249-6
EPA249-7
EPA249-8
EPA249-9
EPA249-10
EPA249-11
EPA249-12
EPA249-13
EPA249-14
EPA249-15
EPA249-16
EPA249-17
EPA249-18
EPA249-19
EPA249-20
EPA249-21
EPA249-22
EPA249G-5
EPA249G-6
EPA249G-7
EPA249G-8
EPA249G-9
EPA249G-10
EPA249G-11
EPA249G-12
EPA249G-13
EPA249G-14
EPA249G-15
EPA249G-16
EPA249G-17
EPA249G-18
EPA249G-19
EPA249G-20
EPA249G-21
EPA249G-22
EPA249J-5
EPA249J-6
EPA249J-7
EPA249J-8
EPA249J-9
EPA249J-10
EPA249J-11
EPA249J-12
EPA249J-13
EPA249J-14
EPA249J-15
EPA249J-16
EPA249J-17
EPA249J-18
EPA249J-19
EPA249J-20
EPA249J-21
EPA249J-22
†Whichever is greater.
EPA249-23
EPA249-24
EPA249-25
EPA249-30
EPA249-35
EPA249-40
EPA249-45
EPA249-50
EPA249-55
EPA249-60
EPA249-65
EPA249-70
EPA249-75
EPA249-80
EPA249-85
EPA249-90
EPA249-95
EPA249-100
SMD-G Part
Number
SMD-J Part
Number
EPA249G-23
EPA249G-24
EPA249G-25
EPA249G-30
EPA249G-35
EPA249G-40
EPA249G-45
EPA249G-50
EPA249G-55
EPA249G-60
EPA249G-65
EPA249G-70
EPA249G-75
EPA249G-80
EPA249G-85
EPA249G-90
EPA249G-95
EPA249G-100
EPA249J-23
EPA249J-24
EPA249J-25
EPA249J-30
EPA249J-35
EPA249J-40
EPA249J-45
EPA249J-50
EPA249J-55
EPA249J-60
EPA249J-65
EPA249J-70
EPA249J-75
EPA249J-80
EPA249J-85
EPA249J-90
EPA249J-95
EPA249J-100
DC Electrical Characteristics
Parameter
Test Conditions
PCA
EPA249-5
Date Code
V OH
V OL
V IK
I IH
.500
MAX
.020
TYP
.250
MAX
.010
TYP
.120 MIN
.
.365
MAX
SMD-G Package
.055
PCA
EPA249G-5
Date Code
.280
MAX
Suggested Solder
.410
Pad Layout
WHITE DOT
PIN#1
.100
.500
MAX
.02
.03
.01
TYP
.250
MAX
.100
.05
Min Max Unit
VCC = min. VIL = max. IOH = max 2.7
VCC = min. VIH = min. I OL= max
VCC = min. II = IIK
VCC = max. VIN = 2.7V
VCC = max. VIN = 5.25V
I IL
Low-Level Input Current
VCC = max. VIN = 0.5V
I OS
Short Circuit Output Current VCC = max. VOUT = 0.
-40
(One output at a time)
I CCH High-Level Supply Current
VCC = max. VIN = OPEN
I CCL Low-Level Supply Current
VCC = max. VIN = 0
TRO Output Rise Time
NH
Fanout High-Level Output
VCC = max. VOH = 2.7V
NL
Fanout Low-Level Output
VCC = max. VOL = 0.5V
.280
MAX
WHITE DOT
PIN#1
.100
TYP
23
24
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
DIP Part
Number
Delay Times referenced from input to leading edges at 25°C, 5.0V, with no load.
DIP Package
.020
TYP
Delay Time
±5% or
±2nS†
High-Level Output Voltage
Low-Level Output Voltage
Input Clamp Voltage
High-Level Input Current
Recommended
Operating Conditions
VCC
VIH
VIL
I IK
I OH
I OL
PW*
d*
TA
115
mA
115
mA
4
nS
20 TTL LOAD
10 TTL LOAD
*These two values are inter-dependent.
Supply Voltage
High-Level Input Voltage
Low-Level Input Voltage
Input Clamp Current
High-Level Output Current
Low-Level Output Current
Pulse Width of Total Delay
Duty Cycle
Operating Free-Air Temperature
Min
Max
Unit
4.75
2.0
5.25
V
V
V
mA
mA
mA
%
%
°C
0.8
-18
-1.0
20
40
0
40
+70
.300
Input Pulse Test Conditions @ 25° C
SMD-J Package
.055
PCA
EPA249J-5
Date Code
WHITE DOT
PIN#1
.280 Suggested Solder
MAX
Pad Layout
.320
.03
.100
.500
MAX
EIN
PW
TRI
PRR
VCC
Pulse Input Voltage
Pulse Width % of Total Delay
Pulse Rise Time (0.75 - 2.4 Volts)
Pulse Repetition Rate
Supply Voltage
.02
DSA249
.100
VCC
7
1
.300
6
2
Volts
%
nS
MHz
Volts
5
3
4 GROUND
QAF-CSO1 Rev. B 8/25/94
Rev. A 2/5/96
Unless Otherwise Noted Dimensions in Inches
Tolerances:
Fractional = ± 1/32
.XX = ± .030
.XXX = ± .010
Unit
3.2
110
2.0
1.0
5.0
Schematic
8
.025
.045
.250
MAX
V
V
V
µA
mA
mA
mA
0.5
-1.2V
50
1.0
-2
-100
ELECTRONICS
INC.
16799 SCHOENBORN ST.
NORTH HILLS, CA 91343
TEL: (818) 892-0761
FAX: (818) 894-5791
Similar pages