Ohmite HVF2512T5002FE High voltage flip chip film Datasheet

HVF Series
Ohmite’s High Voltage Flip Chip Series incorporates
high accuracy screen printing technology to achieve
high voltage capability in a stable flip chip SMD chip
resistor package. The HVF Series offers unmatched
performance in comparison to standard chip resistors. Its unique design provides lower voltage and
temperature coefficients, less noise, tighter tolerances, better stability, higher resistance values, and
higher voltage ratings. HVF is available in convenient
1206 and 2512 footprints.
High Voltage
Flip Chip Film
This product has been
DISCONTINUED
December 2017
F e at u r e s
• High voltage up to 3,000 volts
• Industry standard sizes
• Working temperature range –55°C to 200°C
• Designed for automatic insertion
• Non-magnetic construction
S ER I E S S P E C I F I C AT I O N S
Series
Resistance Range
HVF1206
1K-100M
>100M-10G
>10G-100G
HVF2512
1K-100G
Tol.
1% std.
5%
10%
1% std.
Power Rating (mW)
300
Voltage Rating*
1,500
1000
3,000
*Use Ohm’s Law (V= √P*R) to calculate maximum working voltage.
**Maximum available quantity per reel is 3,500 for 1206 size and 2,000 for 2512 size; call 1-866-9-OHMITE for
details.
ch a r a c t e r is t ics
Resistance Range 1KΩ to 100GΩ
Resistance Tolerance ±1% std.; 5% for HVF1206 100MΩ-10GΩ more; 10% for 10GΩ+
Temperature Coefficient ±100ppm std.
Coating Silicone
Solder Pad Material Silver (PdAg)
Note: HVF Series should not be used with tin-lead based solder compositions. Only silver-based solder compositions are recommended. Care should be taken in the selection of the solder flux contained in the solder paste.
Some pastes are "corrosive" and can damage the coating and also the resistive layer during the soldering process at high temperature. PCBs must be properly cleaned to remove any layers of moisture containing halides
below the resistor.
We recommend Halide Free (or Halogen Free) solder pastes, containing for example ROL0 or similar.
It is advisable for the PCB layout to provide a slot, or air gap, underneath the downward facing resistor element,
thereby increasing insulation resistance and reducing the possibility of capacitive coupling to the PCB. Under no
circumstances should any copper trace be present in the layout directly under the resistive element.
Derating
Voltage coefficient of Resistance
Percent Rated Watts
100
70°
80
60
40
20
0
0
50
100
150
Ambient Temperature, °C
200
Series
Resistance
Range
VCR
(-ppm/V)*
1206
1K ..10MΩ
>10M ..100MΩ
>100M ..1GΩ
>1GΩ .. 5GΩ
<3.20
<15.00
<29.00
<40.00
2512
1K ..30MΩ
>30M ..300MΩ
>300M ..3GΩ
>3GΩ .. 5GΩ
1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • [email protected]
*Typical values. Voltage
coefficient of resistance
strongly depends on the
resistance value. Contact
Ohmite for details.
<0.80
<4.00
<7.00
<10.00
23
HVF Series
High Voltage
Flip Chip Film
p e r fo r m a nc e d a t a
Insulation Resistance >10,000 MΩ
500 Volt 25 °C 75% relative humidity
Dielectric Strength >1,000 Volt
25 °C 75% relative humidity
Thermal Shock ∆ R/R < 0.1% typ., 0.50% max.
MIL Std. 202, method 107, Cond. C (IEC 68 -2 -14)
Overload ∆ R/R < 0.1% typ., 0.50% max.
1,5 x Pnom, 5 sec (do not exceed max. voltage)
Moisture Resistance ∆ R/R < 0.1% typ., 0.50% max.
MIL Std. 202, method 106 (IEC 68 -2 -3)
Load Life ∆ R/R < 0.1% typ., 0.50% max.
1000 hours at rated power (IEC 115 -1)
d i m e nsions
(in. ±0.008)
Silicone
Aluminum Oxide
ta p e a n d r e e l
Per EIA Std. RS-481
a
T
Tape
W
0.069 ±.004
1.75 ±0.10
L
Ruthenium Oxide
0.059 +.004/-0.0
1.5 +0.10/-0.0
0.157 ±.004
4.0 ±0.10
0.079 ±.002
2.0 ±0.05
Silver (PdAg)
B
Land pattern
M
L
N
Land pattern
dimensions are
for reference only
O
Series
HVF1206
HVF2512
L
W
a
T (max.)
0.128
0.063
0.018
0.028
0.252
0.126
0.026
0.032
M
N
O
0.138 ±.002
3.5 ±0.05
0.157 ±.004
4.0 ±0.10
0.032 ±.004
0.81 ±0.10
0.315 ±.012
8.0 ±0.30
A
DIRECTION OF FEED
L
0.150 0.040 0.080 0.070
0.288 0.062 0.140 0.164
O r d e r in g info r m a t ion
Taping Code
blank = bulk package
T = tape & reel
RoHS
Compliant
HVF1206T1004JET
High Voltage Case Size TCR
Ohms
Flip Chip
T = 100 ppm First 3 digits are
1206
Series
V = 50 ppm* significant; last
2512
digit specifies
*Not available for all resistance number of zeros to
values; consult factory
follow. Example:
1006 = 100MΩ
Tolerance
F = 1%
G = 2%
J = 5%
K = 10%
Standard part numbers
Ohms HVF1206--25K ---T2502FE
50K ---T5002FE
75K ---T7502FE
100K ---T1003FE
250K ---T2503FE
500K ---T5003FE
1000K ---T1004FE
1500K ---T1504FE
2000K ---T2004FE
2500K ---T2504FE
5000K ---T5004FE
7500K ---T7504FE
1G ---T1007JE
5G
10G ---T1008JE
HVF2512-----T2502FE
---T5002FE
---T7502FE
---T1003FE
---T2503FE
---T5003FE
---T1004FE
---T1504FE
---T2004FE
---T2504FE
---T5004FE
---T7504FE
---T1007FE
---T5007FE
Trailer
230mm min.–560mm
max. May consist of
carrier and/or cover tape
followed by a minimum
of 160mm of carrier with
sealed cover tape
Components
Leader
Minimum of 40
empty component
pockets sealed
with cover tape
Reel
0.56 max.
14.2 max.
0.512 ±.008
13.0 ±.20
7.00 ±.079
178.0 ±2.0
1.969 min.
50.0 min.
0.331 +.059/-0.0
8.4 +1.5/-0.0
Standard Qty/Reel is 1000; maximum available quantity per reel is 3,500 for
1206 size and 2,000 for 2512 size; call 1-866-9-OHMITE for details.
rev 1/18-1
24
1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • [email protected]
Similar pages