GOOD-ARK GN3J Surface mount glass passivated junction rectifier Datasheet

GN3A THRU GN3M
SURFACE MOUNT GLASS PASSIVATED JUNCTION RECTIFIER
Reverse Voltage - 50 to 1000 Volts
Forward Current - 3.0 Amperes
Features
For surface mounted applications
Low profile package
Built-in strain relief
Easy pick and place
Plasitc package has Underwriters Laboratory
Flammability Classification 94V-0
Glass passivated junction
High temperature soldering:
260 /10 seconds at terminals
Mechanical Data
D IM E N S IO N S
Case: SMC molded plastic
Terminals: Solder plated solderable per
MIL-STD-750, method 2026
Polarity: Indicated by cathode band
Weight: 0.007 ounce, 0.25 gram
D IM
A
in c h e s
m m
M in .
M a x.
M in .
M a x.
0 .2 6 0
0 .2 8 0
6 .6 0
7 .1 1
B
0 .2 2 0
0 .2 4 0
5 .5 9
6 .1 0
C
0 .0 7 5
0 .0 9 5
1 .9 0
2 .4 1
D
0 .1 1 5
0 .1 2 1
2 .9 2
3 .0 7
H
0 .0 0 2 0
0 .0 0 6 0
0 .0 5 1
0 .1 5 2
J
0 .0 0 6
0 .0 1 2
0 .1 5
0 .3 0
K
0 .0 3 0
0 .0 5 0
0 .7 6
1 .2 7
P
S
0 .0 2 0 R E F
0 .3 0 5
0 .3 2 0
N o te
0 .5 1 R E F
7 .7 5
8 .1 3
Maximum Ratings and Electrical Characteristics
Ratings at 25 ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Symbols
GN3A
GN3B
GN3D
GN3G
GN3J
GN3K
GN3M
Units
Maximum repetitive peak reverse voltage
VRRM
50
100
200
400
600
800
1000
Volts
Maximum RMS voltage
VRMS
35
70
140
280
420
560
700
Volts
Maximum DC blocking voltage
VDC
50
100
200
400
600
800
1000
Volts
Maximum average forward rectified current at TL=75
I(AV)
3.0
Amps
Peak forward surge current,
8.3mS single half sine-wave superimposed
on rated load (MIL-STD-750D 4066 method)
IFSM
100.0
Amps
Maximum instantaneous forward voltage at 3.0A
VF
1.20
Volts
IR
5.0
250.0
A
Maximum DC reverse current
at rated DC blocking voltage
TA=25
TA=125
Typical reverse recovery time (Note 1)
Trr
2.5
S
Typical junction capacitance (Note 2)
CJ
60.0
F
13.0
47.0
/W
Maximum thermal resistance (Note 3)
Operating and storage temperature range
R
R
JL
JA
TJ, TSTG
-55 to +150
Notes:
(1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0MHz and applied reverse voltage of 4.0 volts
(3) 8.0mm2 (0.013mm thick) land areas
1
RATINGS AND CHARACTERISTIC CURVES
2
Similar pages