EPCOS B32653A6564 Film capacitors metallized polyester film capacitors (mkt) Datasheet

Film Capacitors
Metallized Polypropylene Film Capacitors (MKP)
Series/Type:
B32651 ... B32656
Date:
May 2009
© EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Metallized polypropylene film capacitors (MKP)
B32651 ... B32656
High pulse (wound)
Typical applications
Electronic ballasts
Switch-mode power supplies
Dimensional drawing
Climatic
Max. operating temperature: 110 °C
Climatic category (IEC 60068-1): 55/100/56
Construction
Dielectric: polypropylene (PP)
Wound capacitor technology with internal
series connection for VR ≥1250 V DC
Plastic case (UL 94 V-0)
Epoxy resin sealing
Features
High pulse strength
High contact reliability
Terminals
Parallel wire leads, lead-free tinned
Special lead lengths available on request
Dimensions in mm
Lead spacing
±0.4
10
15
22.5
27.5
37.5
Marking
Manufacturer's logo,
lot number (
≤27.5 mm), series number
(e.g. 651),
rated capacitance (coded), cap. tolerance (code letter),
rated DC voltage
(AC voltage for 1600 V DC/700 V AC and
2000 V DC/1000 V AC),
date of manufacture (coded)
Delivery mode
Bulk (untaped)
Taped (Ammo pack or reel)
For notes on taping, refer to chapter "Taping and packing“.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 40
Lead diameter
d1
0.6
0.8
0.8
0.8
1.0
Type
B32651
B32652
B32653
B32654
B32656
B32651 ... B32656
High pulse (wound)
Overview of available types
Lead spacing 10 mm
Type
B32651
Page
8
VR (V DC)
1250
VRMS (V AC)
450
CR (nF)
2.2
3.3
4.7
6.8
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 40
B32651 ... B32656
High pulse (wound)
Overview of available types
Lead spacing 15 mm
Type
B32652
Page
9
VR (V DC)
250
400
630
1000
1250
1600
1600
2000
VRMS (V AC)
160
200
250
250
500
500
700
700
CR (nF)
1.0
1.5
2.2
3.3
4.7
5.6
6.8
10
12
15
22
33
47
56
68
100
120
150
220
330
390
470
560
680
820
1000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 4 of 40
B32651 ... B32656
High pulse (wound)
Overview of available types
Lead spacing 22.5 mm
Type
B32653
Page
12
VR (V DC)
250
400
630
1000
1250
1600
2000
2000
VRMS (V AC)
160
200
250
250
500
500
700
1000
CR (nF)
2.2
3.3
4.7
6.8
10
12
15
22
33
47
56
68
82
100
120
150
220
330
470
560
680
1000
1200
1500
2200
3300
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 40
B32651 ... B32656
High pulse (wound)
Overview of available types
Lead spacing 27.5 mm
Type
B32654
Page
15
VR (V DC)
250
400
630
1000
1250
1600
2000
VRMS (V AC)
160
200
250
250
500
500
700
CR (nF)
22
33
47
68
82
100
150
220
330
470
560
680
820
1000
1200
1500
2200
2700
3300
4700
5600
6800
8200
Please read Cautions and warnings and
Important notes at the end of this document.
Page 6 of 40
B32651 ... B32656
High pulse (wound)
Overview of available types
Lead spacing 37.5 mm
Type
B32656
Page
17
VR (V DC)
850
1000
1250
1600
2000
VRMS (V AC)
450
500
500
600
700
CR (nF)
100
150
220
330
470
560
680
820
1000
1200
1500
2200
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 40
B32651
High pulse (wound)
Ordering codes and packing units (lead spacing 10 mm)
VR
V DC1)
1250
VRMS
CR
f ≤1 kHz
V AC
nF
450
2.2
3.3
4.7
6.8
Max. dimensions
w×h×l
mm
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
Ordering code
(composition see
below)
B32651A7222+***
B32651A7332+***
B32651A7472+***
B32651A7682+***
Ammo
pack
pcs./MOQ
4000
3320
3320
2720
Reel
Untaped
pcs./MOQ
6800
5200
5200
4400
pcs./MOQ
4000
4000
4000
4000
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
1) For pulse loads (pulse width ≤ 1000 µs), a peak voltage of 1400 Vp can be permitted.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 40
B32652
High pulse (wound)
Ordering codes and packing units (lead spacing 15 mm)
VR
V DC
250
400
630
VRMS
CR
f ≤1 kHz
V AC
nF
160
150
220
330
470
680
820
1000
200
68
100
150
220
330
470
560
680
250
33
47
68
100
150
220
330
390
Max. dimensions
w×h×l
mm
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
11.0 × 18.5 × 18.0
Ordering code
(composition see
below)
B32652A3154+***
B32652A3224+***
B32652A3334+***
B32652A3474+***
B32652A3684+***
B32652A3824+***
B32652A3105+***
B32652A4683+***
B32652A4104+***
B32652A4154+***
B32652A4224+***
B32652A4334+***
B32652A4474+***
B32652A4564+***
B32652A4684+***
B32652A6333+***
B32652A6473+***
B32652A6683+***
B32652A6104+***
B32652A6154+***
B32652A6224+***
B32652A6334+***
B32652A6394+***
Ammo
pack
pcs./MOQ
4680
3840
3320
2720
2560
4680
4680
3840
3320
2720
2560
4680
4680
3840
3320
2720
2560
Reel
pcs./
MOQ
5200
4400
3600
2800
2800
2200
2200
5200
5200
4400
3600
2800
2800
2200
2200
5200
2800
4400
3600
2800
2800
2200
2200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 9 of 40
Untaped
pcs./
MOQ
4000
4000
1000
2000
2000
1000
1000
4000
4000
4000
4000
2000
2000
1000
1000
4000
4000
4000
4000
2000
2000
1000
1000
B32652
High pulse (wound)
Ordering codes and packing units (lead spacing 15 mm)
VR
V DC
1000
1250
1600
1600
VRMS
CR
f ≤1 kHz
V AC
nF
250
10
15
22
33
47
68
100
120
150
500
6.8
10
15
22
33
47
56
500
3.3
4.7
6.8
10
15
22
700
2.2
3.3
4.7
6.8
10
12
15
Max. dimensions
w×h×l
mm
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
Ordering code
(composition see
below)
B32652A0103+***
B32652A0153+***
B32652A0223+***
B32652A0333+***
B32652A0473+***
B32652A0683+***
B32652A0104+***
B32652A0124+***
B32652A0154+***
B32652A7682+***
B32652A7103+***
B32652A7153+***
B32652A7223+***
B32652A7333+***
B32652A7473+***
B32652A7563+***
B32652A1332+***
B32652A1472+***
B32652A1682+***
B32652A1103+***
B32652A1153+***
B32652A1223+***
B32652J1222+***
B32652J1332+***
B32652J1472+***
B32652J1682+***
B32652J1103+***
B32652J1123+***
B32652J1153+***
Ammo
pack
pcs./MOQ
4680
4680
4680
3840
3320
2720
2560
4680
3840
3320
2720
2560
4680
3840
3320
2720
2560
4680
3840
3320
2720
2560
2560
Reel
pcs./
MOQ
5200
5200
5200
4400
3600
2800
2800
2200
2200
5200
4400
3600
2800
2800
2200
2200
5200
4400
3600
2800
2800
2200
5200
4400
3600
2800
2800
2800
2200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 10 of 40
Untaped
pcs./
MOQ
4000
4000
4000
4000
4000
2000
2000
1000
1000
4000
4000
4000
2000
2000
1000
1000
4000
4000
4000
2000
2000
1000
4000
4000
4000
2000
2000
2000
1000
B32652
High pulse (wound)
Ordering codes and packing units (lead spacing 15 mm)
VR
V DC
2000
VRMS
CR
f ≤1 kHz
V AC
nF
700
1.0
1.5
2.2
3.3
4.7
5.6
6.8
Max. dimensions
w×h×l
mm
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
Ordering code
(composition see
below)
B32652A2102+***
B32652A2152+***
B32652A2222+***
B32652A2332+***
B32652A2472+***
B32652A2562+***
B32652A2682+***
Ammo
pack
pcs./MOQ
4680
3840
3320
2720
2560
Reel
pcs./
MOQ
5200
4400
3600
2800
2800
2200
2200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 11 of 40
Untaped
pcs./
MOQ
4000
4000
4000
2000
2000
1000
1000
B32653
High pulse (wound)
Ordering codes and packing units (lead spacing 22.5 mm)
VR
V DC
250
400
630
VRMS
CR
f ≤1 kHz
V AC
nF
160
220
330
470
680
1000
1200
1500
2200
3300
200
150
220
330
470
680
1000
1200
1500
2200
250
100
150
220
330
470
560
680
1000
1200
Max. dimensions
w×h×l
mm
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
7.0 × 16.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 16.5 × 26.5
10.5 × 18.5 × 26.5
11.0 × 20.5 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
7.0 × 16.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 16.5 × 26.5
11.0 × 20.5 × 26.5
12.0 × 22.0 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 16.5 × 26.5
11.0 × 20.5 × 26.5
11.0 × 20.5 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
Ordering code
(composition see
below)
B32653A3224+***
B32653A3334+***
B32653A3474+***
B32653A3684+***
B32653A3105+***
B32653A3125+***
B32653A3155+***
B32653A3225+000
B32653A3335+000
B32653A4154+***
B32653A4224+***
B32653A4334+***
B32653A4474+***
B32653A4684+***
B32653A4105+***
B32653A4125+000
B32653A4155+000
B32653A4225+000
B32653A6104+***
B32653A6154+***
B32653A6224+***
B32653A6334+***
B32653A6474+***
B32653A6564+***
B32653A6684+000
B32653A6105+000
B32653A6125+000
Ammo
pack
pcs./MOQ
2720
2720
2320
1920
1560
1560
1480
2720
2720
2320
1920
1560
1480
2720
2720
1920
1560
1480
1480
Reel
pcs./
MOQ
2800
2800
2400
2000
1600
1600
1400
2800
2800
2400
2000
1600
1400
2800
2800
2000
1600
1400
1400
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 12 of 40
Untaped
pcs./
MOQ
2880
2880
2520
2040
2160
2160
2040
1040
1040
2880
2880
2520
2040
2160
2040
1800
1040
1040
2880
2880
2040
2160
2040
2040
1040
1040
1040
B32653
High pulse (wound)
Ordering codes and packing units (lead spacing 22.5 mm)
VR
V DC
1000
1250
1600
VRMS
CR
f ≤1 kHz
V AC
nF
250
33
47
68
100
150
220
330
470
560
500
22
33
47
68
100
120
150
220
500
6.8
10
15
22
33
47
56
68
82
100
Max. dimensions
w×h×l
mm
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 16.5 × 26.5
11.0 × 20.5 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 16.5 × 26.5
11.0 × 20.5 × 26.5
12.0 × 22.0 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
7.0 × 16.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 16.5 × 26.5
11.0 × 20.5 × 26.5
12.0 × 22.0 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
Ordering code
(composition see
below)
B32653A0333+***
B32653A0473+***
B32653A0683+***
B32653A0104+***
B32653A0154+***
B32653A0224+***
B32653A0334+000
B32653A0474+000
B32653A0564+000
B32653A7223+***
B32653A7333+***
B32653A7473+***
B32653A7683+***
B32653A7104+***
B32653A7124+000
B32653A7154+000
B32653A7224+000
B32653A1682+***
B32653A1103+***
B32653A1153+***
B32653A1223+***
B32653A1333+***
B32653A1473+***
B32653A1563+000
B32653A1683+000
B32653A1823+000
B32653A1104+000
Ammo
pack
pcs./MOQ
2720
2720
2720
1920
1560
1480
2720
2720
1920
1560
1480
2720
2720
2320
1920
1560
1480
Reel
pcs./
MOQ
2800
2800
2800
2000
1600
1400
2800
2800
2000
1600
1400
2800
2800
2400
2000
1600
1400
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 13 of 40
Untaped
pcs./
MOQ
2880
2880
2880
2040
2160
2040
2160
2160
2160
2880
2880
2040
2160
2040
1800
1040
1040
2880
2880
2520
2040
2160
2040
1800
1040
1040
1040
B32653
High pulse (wound)
Ordering codes and packing units (lead spacing 22.5 mm)
VR
V DC
2000
2000
VRMS
CR
f ≤1 kHz
V AC
nF
700
3.3
4.7
6.8
10
15
22
33
1000
2.2
3.3
4.7
6.8
10
12
15
22
Max. dimensions
w×h×l
mm
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 16.5 × 26.5
11.0 × 20.5 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 16.5 × 26.5
10.5 × 20.5 × 26.5
12.0 × 22.0 × 26.5
14.5 × 29.5 × 26.5
14.5 × 29.5 × 26.5
Ordering code
(composition see
below)
B32653A2332+***
B32653A2472+***
B32653A2682+***
B32653A2103+***
B32653A2153+***
B32653A2223+000
B32653A2333+000
B32653A8222+***
B32653A8332+***
B32653A8472+***
B32653A8682+***
B32653A8103+***
B32653A8123+000
B32653A8153+000
B32653A8223+000
Ammo
pack
pcs./MOQ
2720
2720
1920
1560
1480
2720
2720
1920
1560
1560
Reel
pcs./
MOQ
2800
2800
2000
1600
1400
2800
2800
2000
1600
1600
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 14 of 40
Untaped
pcs./
MOQ
2880
2880
2040
2160
2040
2160
2160
2880
2880
2040
2160
2160
1800
2160
2160
B32654
High pulse (wound)
Ordering codes and packing units (lead spacing 27.5 mm)
VR
V DC
250
400
630
1000
VRMS
CR
f ≤1 kHz
V AC
nF
160
1500
2200
3300
4700
5600
6800
8200
200
1000
1500
2200
3300
4700
5600
250
680
1000
1500
2200
2700
3300
250
220
330
470
680
820
1000
1200
1500
Max. dimensions
w×h×l
mm
11.0 × 21.0 × 31.5
12.5 × 21.5 × 31.5
15.0 × 24.5 × 31.5
18.0 × 27.5 × 31.5
19.0 × 30.0 × 31.5
22.0 × 36.5 × 31.5
22.0 × 36.5 × 31.5
11.0 × 21.0 × 31.5
12.5 × 21.5 × 31.5
14.0 × 24.5 × 31.5
19.0 × 30.0 × 31.5
22.0 × 36.5 × 31.5
22.0 × 36.5 × 31.5
11.0 × 21.0 × 31.5
13.5 × 23.0 × 31.5
18.0 × 27.5 × 31.5
18.0 × 33.0 × 31.5
22.0 × 36.5 × 31.5
22.0 × 36.5 × 31.5
11.0 × 21.0 × 31.5
11.0 × 21.0 × 31.5
14.0 × 24.5 × 31.5
18.0 × 27.5 × 31.5
19.0 × 30.0 × 31.5
21.0 × 31.0 × 31.5
22.0 × 36.5 × 31.5
22.0 × 36.5 × 31.5
Ordering code
(composition see
below)
B32654A3155+***
B32654A3225+***
B32654A3335+000
B32654A3475+000
B32654A3565+000
B32654A3685+000
B32654A3825+000
B32654A4105+***
B32654A4155+***
B32654A4225+***
B32654A4335+000
B32654A4475+000
B32654A4565+000
B32654A6684+***
B32654A6105+***
B32654A6155+000
B32654A6225+000
B32654A6275+000
B32654A6335K000
B32654A0224+***
B32654A0334+***
B32654A0474+***
B32654A0684+000
B32654A0824+000
B32654A0105+000
B32654A0125+000
B32654A0155K000
Ammo
pack
pcs./MOQ
Reel
pcs./
MOQ
1400
1200
1400
1200
1040
1400
1000
1400
1400
1040
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 15 of 40
Untaped
pcs./
MOQ
1280
1120
960
800
720
784
784
1280
1120
1040
720
784
784
1280
1040
800
952
784
784
1280
1280
1040
800
720
784
784
784
B32654
High pulse (wound)
Ordering codes and packing units (lead spacing 27.5 mm)
VR
V DC
1250
1600
2000
VRMS
CR
f ≤1 kHz
V AC
nF
500
100
150
220
330
470
560
680
500
47
68
100
150
220
700
22
33
47
68
82
100
Max. dimensions
w×h×l
mm
11.0 × 21.0 × 31.5
11.0 × 21.0 × 31.5
14.0 × 24.5 × 31.5
18.0 × 27.5 × 31.5
21.0 × 31.0 × 31.5
22.0 × 36.5 × 31.5
22.0 × 36.5 × 31.5
11.0 × 21.0 × 31.5
11.0 × 21.0 × 31.5
14.0 × 24.5 × 31.5
18.0 × 27.5 × 31.5
21.0 × 31.0 × 31.5
11.0 × 21.0 × 31.5
13.5 × 23.0 × 31.5
18.0 × 27.5 × 31.5
19.0 × 30.0 × 31.5
22.0 × 36.5 × 31.5
22.0 × 36.5 × 31.5
Ordering code
(composition see
below)
B32654A7104+***
B32654A7154+***
B32654A7224+***
B32654A7334+000
B32654A7474+000
B32654A7564+000
B32654A7684+000
B32654A1473+***
B32654A1683+***
B32654A1104+***
B32654A1154+000
B32654A1224+000
B32654A2223+***
B32654A2333+***
B32654A2473+000
B32654A2683+000
B32654A2823+000
B32654A2104+000
Ammo
pack
pcs./MOQ
Reel
pcs./
MOQ
1400
1400
1040
1400
1400
1040
1400
1000
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
189 = Reel
000 = Untaped (lead length 6 1 mm)
Page 16 of 40
Untaped
pcs./
MOQ
1280
1280
1040
800
784
784
784
1280
1280
1040
800
784
1280
1040
800
720
784
784
B32656
High pulse (wound)
Ordering codes and packing units (lead spacing 37.5 mm)
VR
V DC
850
1000
1250
1600
2000
VRMS
CR
f ≤1 kHz
V AC
nF
450
220
330
470
680
1000
500
470
680
1000
1200
1500
2200
500
220
330
470
680
820
1000
1200
600
100
150
220
330
470
560
680
820
700
100
150
220
330
470
Max. dimensions
w×h×l
mm
12.0 × 22.0 × 42.0
12.0 × 22.0 × 42.0
12.0 × 22.0 × 42.0
16.0 × 28.5 × 42.0
18.0 × 32.5 × 42.0
14.0 × 25.0 × 42.0
16.0 × 28.5 × 42.0
20.0 × 39.5 × 42.0
28.0 × 37.0 × 42.0
28.0 × 37.0 × 42.0
30.0 × 45.0 × 42.0
14.0 × 25.0 × 42.0
16.0 × 28.5 × 42.0
18.0 × 32.5 × 42.0
20.0 × 39.5 × 42.0
28.0 × 37.0 × 42.0
28.0 × 37.0 × 42.0
28.0 × 42.5 × 41.5
12.0 × 22.0 × 42.0
14.0 × 25.0 × 42.0
16.0 × 28.5 × 42.0
20.0 × 39.5 × 41.5
28.0 × 37.0 × 42.0
28.0 × 37.0 × 42.0
28.0 × 42.5 × 41.5
30.0 × 45.0 × 42.0
14.0 × 25.0 × 42.0
18.0 × 32.5 × 42.0
20.0 × 39.5 × 42.0
28.0 × 37.0 × 42.0
30.0 × 45.0 × 42.0
Ordering code
(composition see
below)
B32656A8224+000
B32656A8334+000
B32656A8474+000
B32656A8684+000
B32656A8105+000
B32656A0474+000
B32656A0684+000
B32656A0105+000
B32656A0125+000
B32656A0155+000
B32656A0225+000
B32656A7224+000
B32656A7334+000
B32656A7474+000
B32656A7684+000
B32656A7824+000
B32656A7105+000
B32656A7125+000
B32656J1104+000
B32656J1154+000
B32656J1224+000
B32656J1334+000
B32656J1474+000
B32656J1564+000
B32656J1684+000
B32656J1824+000
B32656J2104+000
B32656J2154+000
B32656J2224+000
B32656J2334+000
B32656J2474+000
Untaped
pcs./MOQ
1620
1620
1620
800
720
1380
800
640
440
440
440
1380
800
720
640
440
440
440
1620
1380
800
640
440
440
440
440
1380
720
640
440
400
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
K = ±10%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
000 = Untaped (lead length 6 1 mm)
Page 17 of 40
B32651 ... B32656
High pulse (wound)
Technical data
Operating temperature range
Max. operating temperature Top,max
Upper category temperature Tmax
Lower category temperature Tmin
Rated temperature TR
Dissipation factor tan δ (in 10-3) at
at 20 °C
(upper limit values)
≤27 nF 27 nF<CR≤0.1 µF
1 kHz 0.8
10 kHz 1.0
100 kHz 2.0
0.8
1.0
3.0
CR ≤ 0.33 µF
CR > 0.33 µF
Insulation resistance Rins
or time constant τ = CR Rins
100 GΩ
30000 s
at 20 °C, rel. humidity ≤ 65%
(minimum as-delivered values)
DC test voltage
1.6 VR, 2 s
TA (°C)
DC voltage derating
Category voltage VC
(continuous operation with VDC TA ≤ 85
VC = VR
or VAC at f ≤ 1 kHz)
85<TA≤100 VC = VR (165TA)/80
TA (°C)
DC voltage (max. hours)
Operating voltage Vop for
short operating periods
TA ≤ 85
Vop = 1.25 VC (2000 h)
(VDC or VAC at f ≤ 1 kHz)
85<TA≤100 Vop = 1.25 VC (2000 h)
Damp heat test
56 days/40 °C/93% relative humidity
Limit values after damp
Capacitance change ∆C/C
heat test
Dissipation factor change ∆ tan δ
Insulation resistance Rins
or time constant τ = CR Rins
Reliability:
Failure rate λ
Service life tSL
Failure criteria:
Total failure
Failure due to variation
of parameters
Please read Cautions and warnings and
Important notes at the end of this document.
+110 °C
+100 °C
55 °C
+85 °C
0.1 µF<CR≤1 µF >1 µF
0.8
1.0
0.8
AC voltage derating
VC,RMS = VRMS
VC,RMS=VRMS (165TA)/80
AC voltage (max. hours)
Vop = 1.0 VC,RMS (2000 h)
Vop = 1.0 VC,RMS (2000 h)
≤ 3%
≤ 0.5 10-3 (at 1 kHz)
≤ 1.0 10-3 (at 10 kHz)
≥ 50% of minimum
as-delivered values
1 fit (≤ 1 10-9/h) at 0.5 VR, 40 °C
200 000 h at 1.0 VR, 85 °C
For conversion to other operating conditions and temperatures,
refer to chapter "Quality, 2 Reliability".
Short circuit or open circuit
Capacitance change ∆C/C
Dissipation factor tan δ
Insulation resistance Rins
or time constant τ = CR Rins
Page 18 of 40
> 10%
> 4 upper limit value
< 1500 MΩ (CR≤0.33 µF)
< 500 s (CR>0.33 µF)
B32651 ... B32656
High pulse (wound)
Pulse handling capability
"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal
voltages, expressed in V/µs.
"k0" represents the maximum permissible pulse characteristic of the waveform applied to the
capacitor, expressed in V2/µs.
Note:
The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the
capacitor.
dV/dt values
Lead spacing
VR
VRMS
V DC
V AC
250
160
400
200
630
250
850
450
1000
250
500
1250
450
500
1600
500
600
700
2000
700
1000
10 mm
15 mm
22.5 mm
27.5 mm
37.5 mm
dV/dt in V/µs
4000
200
300
400
975
1850
4500
5200
8000
120
180
300
600
1150
2400
7000
7500
50
100
150
300
600
1000
2300
90
100
140
210
200
Please read Cautions and warnings and
Important notes at the end of this document.
Page 19 of 40
B32651 ... B32656
High pulse (wound)
k0 values
Lead spacing
VR
VRMS
V DC
V AC
250
160
400
200
630
250
850
450
1000
250
500
1250
450
500
1600
500
600
700
2000
700
1000
10 mm
k0 in V2/µs
25 000 000
15 mm
22.5 mm
100 000
250 000
500 000
60 000
200 000
350 000
25 000
110 000
250 000
3 000 000
9 000 000
20 000 000
28 000 000
60 000 000
1 500 000
3 750 000
10 000 000
1 000 000
2 000 000
4 000 000
15 000 000
40 000 000
50 000 000
Impedance Z versus frequency f
(typical values)
Please read Cautions and warnings and
Important notes at the end of this document.
27.5 mm
Page 20 of 40
37.5 mm
153 000
180 000
350 000
672 000
800 000
B32651
High pulse (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C)
For TA >90 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 10 mm
1250 V DC/450 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 21 of 40
B32652
High pulse (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C)
For TA >90 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 15 mm
250 V DC/160 V AC
400 V DC/200 V AC
630 V DC/250 V AC
1000 V DC/250 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 22 of 40
B32652
High pulse (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C)
For TA >90 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 15 mm
1250 V DC/500 V AC
1600 V DC/500 V AC
1600 V DC/700 V AC
2000 V DC/700 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 23 of 40
B32653
High pulse (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C)
For TA >90 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 22.5 mm
250 V DC/160 V AC
400 V DC/200 V AC
630 V DC/250 V AC
1000 V DC/250 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 24 of 40
B32653
High pulse (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C)
For TA >90 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 22.5 mm
1250 V DC/500 V AC
1600 V DC/500 V AC
2000 V DC/700 V AC
2000 V DC/1000 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 25 of 40
B32654
High pulse (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C)
For TA >90 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 27.5 mm
250 V DC/160 V AC
400 V DC/200 V AC
630 V DC/250 V AC
1000 V DC/250 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 26 of 40
B32654
High pulse (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C)
For TA >90 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 27.5 mm
1250 V DC/500 V AC
1600 V DC/500 V AC
2000 V DC/700 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 27 of 40
B32656
High pulse (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C)
For TA >90 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 37.5 mm
850 V DC/450 V AC
1000 V DC/500 V AC
1250 V DC/500 V AC
1600 V DC/600 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 28 of 40
B32656
High pulse (wound)
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA ≤90 °C)
For TA >90 °C, please refer to "General technical information", section 3.2.3.
Lead spacing 37.5 mm
2000 V DC/700 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 29 of 40
B32651 ... B32656
High pulse (wound)
Mounting guidelines
1
Soldering
1.1
Solderability of leads
The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1.
Before a solderability test is carried out, terminals are subjected to accelerated ageing (to
IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far
higher than the upper category temperature of the capacitors, the terminal wires should be cut off
from the capacitor before the ageing procedure to prevent the solderability being impaired by the
products of any capacitor decomposition that might occur.
Solder bath temperature
235 ±5 °C
Soldering time
2.0 ±0.5 s
Immersion depth
2.0 +0/0.5 mm from capacitor body or seating plane
Evaluation criteria:
Visual inspection
Wetting of wire surface by new solder ≥90%, free-flowing solder
1.2
Resistance to soldering heat
Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A.
Conditions:
Series
Solder bath temperature Soldering time
MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C
coated
uncoated (lead spacing > 10 mm)
MFP
MKP (lead spacing > 7.5 mm)
MKT boxed (case 2.5 × 6.5 × 7.2 mm)
MKP (lead spacing ≤ 7.5 mm)
MKT uncoated (lead spacing ≤ 10 mm)
insulated (B32559)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 30 of 40
10 ±1 s
5 ±1 s
<4s
recommended soldering
profile for MKT uncoated
(lead spacing ≤ 10 mm) and
insulated (B32559)
B32651 ... B32656
High pulse (wound)
Immersion depth
2.0 +0/0.5 mm from capacitor body or seating plane
Shield
Heat-absorbing board, (1.5 ±0.5) mm thick, between capacitor
body and liquid solder
Evaluation criteria:
Visual inspection
∆C/C0
tan δ
Please read Cautions and warnings and
Important notes at the end of this document.
No visible damage
2% for MKT/MKP/MFP
5% for EMI suppression capacitors
As specified in sectional specification
Page 31 of 40
B32651 ... B32656
High pulse (wound)
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper category temperature Tmax. Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable countermeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 °C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 °C
MKT 160 °C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled after the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤10 mm (B32560/B32561) the following measures are recommended:
pre-heating to not more than 110 °C in the preheater phase
rapid cooling after soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 32 of 40
B32651 ... B32656
High pulse (wound)
2
Cleaning
To determine whether the following solvents, often used to remove flux residues and other substances, are suitable for the capacitors described, refer to the table below:
Type
Ethanol,
isopropanol,
n-propanol
MKT
(uncoated)
MKT, MKP, MFP
(coated/boxed)
Suitable
n-propanol-water
mixtures,
water with surface
tension-reducing
tensides (neutral)
Unsuitable
Solvent from
table A (see
next page)
Suitable
Suitable
Solvent from
table B (see
next page)
In part suitable Unsuitable
Even when suitable solvents are used, a reversible change of the electrical characteristics may
occur in uncoated capacitors immediately after they are washed. Thus it is always recommended
to dry the components (e.g. 4 h at 70 °C) before they are subjected to subsequent electrical testing.
Table A
Manufacturers' designations for trifluoro-trichloro-ethane-based cleaning solvents (selection)
Trifluoro-trichloroethane
Freon TF
Frigen 113 TR
Arklone P
Kaltron 113 MDR
Flugene 113
Mixtures of trifluoro-trichloro-ethane with ethanol and
isopropanol
Freon TE 35; Freon TP 35; Freon TES
Frigen 113 TR-E; Frigen 113 TR-P; Frigen TR-E 35
Arklone A; Arklone L; Arklone K
Kaltron 113 MDA; Kaltron 113 MDI; Kaltron 113 MDI 35
Flugene 113 E; Flugene 113 IPA
Manufacturer
Du Pont
Hoechst
ICI
Kali-Chemie
Rhone-Progil
Table B (worldwide banned substances)
Manufacturers' designations for unsuitable cleaning solvents (selection)
Mixtures of chlorinated hydrocarbons and ketones with fluorated hydrocarbons
Freon TMC; Freon TA; Freon TC
Arklone E
Kaltron 113 MDD; Kaltron 113 MDK
Flugene 113 CM
Please read Cautions and warnings and
Important notes at the end of this document.
Page 33 of 40
Manufacturer
Du Pont
ICI
Kali-Chemie
Rhone-Progil
B32651 ... B32656
High pulse (wound)
3
Embedding of capacitors in finished assemblies
In many applications, finished circuit assemblies are embedded in plastic resins. In this case,
both chemical and thermal influences of the embedding ("potting") and curing processes must be
taken into account.
Our experience has shown that the following potting materials can be recommended: non-flexible
epoxy resins with acid-anhydride hardeners; chemically inert, non-conducting fillers; maximum
curing temperature of 100 °C.
Caution:
Consult us first if you wish to embed uncoated types!
Please read Cautions and warnings and
Important notes at the end of this document.
Page 34 of 40
B32651 ... B32656
High pulse (wound)
Cautions and warnings
Do not exceed the upper category temperature (UCT).
Do not apply any mechanical stress to the capacitor terminals.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after it has been soldered to the PC board.
Do not pick up the PC board by the soldered capacitor.
Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified
lead spacing.
Do not exceed the specified time or temperature limits during soldering.
Avoid external energy inputs, such as fire or electricity.
Avoid overload of the capacitors.
The table below summarizes the safety instructions that must always be observed. A detailed description can be found in the relevant sections of the chapters "General technical information" and
"Mounting guidelines".
Topic
Storage conditions
Flammability
Resistance to
vibration
Safety information
Reference chapter
"General technical
information"
Make sure that capacitors are stored within the
4.5
specified range of time, temperature and humidity "Storage conditions"
conditions.
Avoid external energy, such as fire or electricity
5.3
(passive flammability), avoid overload of the
"Flammability"
capacitors (active flammability) and consider the
flammability of materials.
Do not exceed the tested ability to withstand
5.2
vibration. The capacitors are tested to
"Resistance to vibration"
IEC 60068-2-6.
EPCOS offers film capacitors specially designed
for operation under more severe vibration regimes
such as those found in automotive applications.
Consult our catalog "Film Capacitors for
Automotive Electronics".
Please read Cautions and warnings and
Important notes at the end of this document.
Page 35 of 40
B32651 ... B32656
High pulse (wound)
Topic
Safety information
Soldering
Do not exceed the specified time or temperature
limits during soldering.
Cleaning
Use only suitable solvents for cleaning capacitors.
Embedding of
When embedding finished circuit assemblies in
capacitors in
plastic resins, chemical and thermal influences
finished assemblies must be taken into account.
Caution: Consult us first, if you also wish to
embed other uncoated component types!
Please read Cautions and warnings and
Important notes at the end of this document.
Page 36 of 40
Reference chapter
"Mounting guidelines"
1 "Soldering"
2 "Cleaning"
3 "Embedding of
capacitors in finished
assemblies"
B32651 ... B32656
High pulse (wound)
Symbols and terms
Symbol
α
αC
A
βC
C
CR
∆C
∆C/C
∆C/CR
dt
∆t
∆T
∆tan δ
∆V
dV/dt
∆V/∆t
E
ESL
ESR
f
f1
f2
fr
FD
FT
i
IC
English
Heat transfer coefficient
Temperature coefficient of capacitance
Capacitor surface area
Humidity coefficient of capacitance
Capacitance
Rated capacitance
Absolute capacitance change
Relative capacitance change (relative
deviation of actual value)
Capacitance tolerance (relative deviation
from rated capacitance)
Time differential
Time interval
Absolute temperature change
(self-heating)
Absolute change of dissipation factor
Absolute voltage change
Time differential of voltage function (rate
of voltage rise)
Voltage change per time interval
Activation energy for diffusion
Self-inductance
Equivalent series resistance
Frequency
Frequency limit for reducing permissible
AC voltage due to thermal limits
German
Wärmeübergangszahl
Temperaturkoeffizient der Kapazität
Kondensatoroberfläche
Feuchtekoeffizient der Kapazität
Kapazität
Nennkapazität
Absolute Kapazitätsänderung
Relative Kapazitätsänderung (relative
Abweichung vom Ist-Wert)
Kapazitätstoleranz (relative Abweichung
vom Nennwert)
Differentielle Zeit
Zeitintervall
Absolute Temperaturänderung
(Selbsterwärmung)
Absolute Änderung des Verlustfaktors
Absolute Spannungsänderung
Differentielle Spannungsänderung
(Spannungsflankensteilheit)
Spannungsänderung pro Zeitintervall
Aktivierungsenergie zur Diffusion
Eigeninduktivität
Ersatz-Serienwiderstand
Frequenz
Grenzfrequenz für thermisch bedingte
Reduzierung der zulässigen
Wechselspannung
Frequency limit for reducing permissible Grenzfrequenz für strombedingte
AC voltage due to current limit
Reduzierung der zulässigen
Wechselspannung
Resonant frequency
Resonanzfrequenz
Thermal acceleration factor for diffusion Therm. Beschleunigungsfaktor zur
Diffusion
Derating factor
Deratingfaktor
Current (peak)
Stromspitze
Category current (max. continuous
Kategoriestrom (max. Dauerstrom)
current)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 37 of 40
B32651 ... B32656
High pulse (wound)
Symbol
IRMS
iz
k0
LS
λ
λ0
λtest
Pdiss
Pgen
Q
ρ
R
R
Ri
Rins
RP
RS
S
t
T
τ
tan δ
tan δD
tan δP
tan δS
TA
Tmax
Tmin
tOL
Top
TR
Tref
tSL
VAC
English
(Sinusoidal) alternating current,
root-mean-square value
Capacitance drift
Pulse characteristic
Series inductance
Failure rate
Constant failure rate during useful
service life
Failure rate, determined by tests
Dissipated power
Generated power
Heat energy
Density of water vapor in air
Universal molar constant for gases
Ohmic resistance of discharge circuit
Internal resistance
Insulation resistance
Parallel resistance
Series resistance
severity (humidity test)
Time
Temperature
Time constant
Dissipation factor
Dielectric component of dissipation
factor
Parallel component of dissipation factor
Series component of dissipation factor
Ambient temperature
Upper category temperature
Lower category temperature
Operating life at operating temperature
and voltage
Operating temperature
Rated temperature
Reference temperature
Reference service life
AC voltage
Please read Cautions and warnings and
Important notes at the end of this document.
German
(Sinusförmiger) Wechselstrom
Inkonstanz der Kapazität
Impulskennwert
Serieninduktivität
Ausfallrate
Konstante Ausfallrate in der
Nutzungsphase
Experimentell ermittelte Ausfallrate
Abgegebene Verlustleistung
Erzeugte Verlustleistung
Wärmeenergie
Dichte von Wasserdampf in Luft
Allg. Molarkonstante für Gas
Ohmscher Widerstand des
Entladekreises
Innenwiderstand
Isolationswiderstand
Parallelwiderstand
Serienwiderstand
Schärfegrad (Feuchtetest)
Zeit
Temperatur
Zeitkonstante
Verlustfaktor
Dielektrischer Anteil des Verlustfaktors
Parallelanteil des Verlfustfaktors
Serienanteil des Verlustfaktors
Umgebungstemperatur
Obere Kategorietemperatur
Untere Kategorietemperatur
Betriebszeit bei Betriebstemperatur und
-spannung
Beriebstemperatur
Nenntemperatur
Referenztemperatur
Referenz-Lebensdauer
Wechselspannung
Page 38 of 40
B32651 ... B32656
High pulse (wound)
Symbol
VC
VC,RMS
English
Category voltage
Category AC voltage
VCD
Vch
VDC
VFB
Vi
Vo
Vop
Vp
Vpp
VR
Corona-discharge onset voltage
Charging voltage
DC voltage
Fly-back capacitor voltage
Input voltage
Output voltage
Operating voltage
Peak pulse voltage
Peak-to-peak voltage Impedance
Rated voltage
Amplitude of rated AC voltage
R
VRMS
German
Kategoriespannung
(Sinusförmige)
Kategorie-Wechselspannung
Teilentlade-Einsatzspannung
Ladespannung
Gleichspannung
Spannung (Flyback)
Eingangsspannung
Ausgangssspannung
Betriebsspannung
Impuls-Spitzenspannung
Spannungshub
Nennspannung
Amplitude der Nenn-Wechselspannung
VSC
Vsn
(Sinusoidal) alternating voltage,
root-mean-square value
S-correction voltage
Snubber capacitor voltage
Z
Impedance
Spannung bei Anwendung "S-correction"
Spannung bei Anwendung
"Beschaltung"
Scheinwiderstand
Lead spacing
Rastermaß
Please read Cautions and warnings and
Important notes at the end of this document.
(Sinusförmige) Wechselspannung
Page 39 of 40
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP,
MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT,
SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse,
WindCap are trademarks registered or pending in Europe and in other countries. Further
information will be found on the Internet at www.epcos.com/trademarks.
Page 40 of 40
Similar pages