AD AD8047AN 250 mhz, general purpose voltage feedback op amp Datasheet

a
FEATURES
Wide Bandwidth
AD8047, G = +1 AD8048, G = +2
Small Signal
250 MHz
260 MHz
Large Signal (2 V p-p) 130 MHz
160 MHz
5.8 mA Typical Supply Current
Low Distortion, (SFDR) Low Noise
–66 dBc typ @ 5 MHz
–54 dBc typ @ 20 MHz
5.2 nV/√Hz (AD8047), 3.8 nV/√Hz (AD8048) Noise
Drives 50 pF Capacitive Load
High Speed
Slew Rate 750 V/µs (AD8047), 1000 V/µs (AD8048)
Settling 30 ns to 0.01%, 2 V Step
±3 V to ±6 V Supply Operation
APPLICATIONS
Low Power ADC Input Driver
Differential Amplifiers
IF/RF Amplifiers
Pulse Amplifiers
Professional Video
DAC Current to Voltage Conversion
Baseband and Video Communications
Pin Diode Receivers
Active Filters/Integrators
PRODUCT DESCRIPTION
250 MHz, General Purpose
Voltage Feedback Op Amps
AD8047/AD8048
FUNCTIONAL BLOCK DIAGRAM
8-Pin Plastic Mini-DIP (N), Cerdip (Q)
and SO (R) Packages
NC
1
8
NC
–INPUT
2
7
+VS
+INPUT
3
6
OUTPUT
5
NC
–V S
4
AD8047/48
(Top View)
NC = NO CONNECT
The AD8047 and AD8048’s low distortion and cap load drive
make the AD8047/AD8048 ideal for buffering high speed
ADCs. They are suitable for 12 bit/10 MSPS or 8 bit/60 MSPS
ADCs. Additionally, the balanced high impedance inputs of the
voltage feedback architecture allow maximum flexibility when
designing active filters.
The AD8047 and AD8048 are offered in industrial (–40°C to
+85°C) temperature ranges and are available in 8-pin plastic
DIP and SOIC packages.
The AD8047 and AD8048 are very high speed and wide bandwidth amplifiers. The AD8047 is unity gain stable. The
AD8048 is stable at gains of two or greater. The AD8047 and
AD8048, which utilize a voltage feedback architecture, meet the
requirements of many applications that previously depended on
current feedback amplifiers.
A proprietary circuit has produced an amplifier that combines
many of the best characteristics of both current feedback and
voltage feedback amplifiers. For the power (6.6 mA max) the
AD8047 and AD8048 exhibit fast and accurate pulse response
(30 ns to 0.01%) as well as extremely wide small signal and
large signal bandwidth and low distortion. The AD8047
achieves –54 dBc distortion at 20 MHz and 250 MHz small signal and 130 MHz large signal bandwidths.
1V
5ns
Figure 1. AD8047 Large Signal Transient Response,
VO = 4 V p-p, G = +1
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
© Analog Devices, Inc., 1995
One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
AD8047/AD8048–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (±V = ±5 V; R
S
Parameter
DYNAMIC PERFORMANCE
Bandwidth (–3 dB)
Small Signal
Large Signal1
Bandwidth for 0.1 dB Flatness
Slew Rate, Average +/–
Rise/Fall Time
Settling Time
To 0.1%
To 0.01%
HARMONIC/NOISE PERFORMANCE
2nd Harmonic Distortion
3rd Harmonic Distortion
Input Voltage Noise
Input Current Noise
Average Equivalent Integrated
Input Noise Voltage
Differential Gain Error (3.58 MHz)
Differential Phase Error (3.58 MHz)
LOAD
= 100 Ω; AV = 1 (AD8047); AV = 2 (AD8048), unless otherwise noted)
Conditions
VOUT ≤ 0.4 V p-p
VOUT = 2 V p-p
VOUT = 300 mV p-p
8047, RF = 0 Ω; 8048, RF = 200 Ω
VOUT = 4 V Step
VOUT = 0.5 V Step
VOUT = 4 V Step
AD8047A
Min Typ Max
AD8048A
Min Typ Max
Units
170
100
180
135
260
160
MHz
MHz
50
1000
1.2
3.2
MHz
V/µs
ns
ns
475
250
130
35
750
1.1
4.3
VOUT = 2 V Step
VOUT = 2 V Step
13
30
13
30
ns
ns
2 V p-p; 20 MHz
RL = 1 kΩ
2 V p-p; 20 MHz
RL = 1 kΩ
f = 100 kHz
f = 100 kHz
–54
–64
–60
–61
5.2
1.0
–48
–60
–56
–65
3.8
1.0
dBc
dBc
dBc
dBc
nV/√Hz
pA/√Hz
0.1 MHz to 10 MHz
RL = 150 Ω, G = +2
RL = 150 Ω, G = +2
16
0.02
0.03
11
0.01
0.02
µV rms
%
Degree
DC PERFORMANCE2, RL = 150 Ω
Input Offset Voltage3
1
TMIN –TMAX
±5
1
Offset Voltage Drift
Input Bias Current
TMIN –TMAX
Input Offset Current
Common-Mode Rejection Ratio
Open-Loop Gain
740
0.5
TMIN –TMAX
VCM = ± 2.5 V
VOUT = ± 2.5 V
TMIN –TMAX
74
58
54
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
OUTPUT CHARACTERISTICS
Output Voltage Range, RL = 150 Ω
Output Current
Output Resistance
Short Circuit Current
POWER SUPPLY
Operating Range
Quiescent Current
1
±5
1
3.5
6.5
2
3
80
62
0.5
74
65
56
3
4
3.5
6.5
2
3
80
68
mV
mV
µV/°C
µA
µA
µA
µA
dB
dB
dB
500
1.5
± 3.4
500
1.5
± 3.4
kΩ
pF
V
± 2.8
± 3.0
50
0.2
130
± 2.8 ± 3.0
50
0.2
130
V
mA
Ω
mA
± 3.0
± 5.0 ± 6.0
5.8 6.6
7.5
78
± 3.0 ± 5.0 ± 6.0
5.9 6.6
7.5
72
78
V
mA
mA
dB
TMIN –TMAX
Power Supply Rejection Ratio
3
4
72
NOTES
1
See Max Ratings and Theory of Operation sections of data sheet.
2
Measured at AV = 50.
3
Measured with respect to the inverting input.
Specifications subject to change without notice.
–2–
REV. 0
AD8047/AD8048
ABSOLUTE MAXIMUM RATINGS 1
MAXIMUM POWER DISSIPATION
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V
Voltage Swing × Bandwidth Product (AD8047) . . . 180 V – MHz
(AD8048) . . . 250 V – MHz
Internal Power Dissipation2
Plastic Package (N) . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Watts
Small Outline Package (R) . . . . . . . . . . . . . . . . . . . 0.9 Watts
Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ± VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 1.2 V
Output Short Circuit Duration
. . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves
Storage Temperature Range (N, R) . . . . . . . . –65°C to +125°C
Operating Temperature Range (A Grade) . . . –40°C to +85°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C
The maximum power that can be safely dissipated by these devices is limited by the associated rise in junction temperature.
The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature
of the plastic, approximately +150°C. Exceeding this limit temporarily may cause a shift in parametric performance due to a
change in the stresses exerted on the die by the package. Exceeding a junction temperature of +175°C for an extended period can
result in device failure.
While the AD8047 and AD8048 are internally short circuit protected, this may not be sufficient to guarantee that the maximum junction temperature (+150°C) is not exceeded under all
conditions. To ensure proper operation, it is necessary to observe the maximum power derating curves.
NOTES
1
Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only, and functional
operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2
Specification is for device in free air:
8-Pin Plastic DIP Package: θ JA = 90°C/Watt
8-Pin SOIC Package: θJA = 140°C/Watt
MAXIMUM POWER DISSIPATION – Watts
2.0
METALIZATION PHOTOS
Dimensions shown in inches and (mm).
Connect Substrate to –V S.
AD8047
+VS
8-PIN MINI-DIP PACKAGE
TJ = +150°C
1.5
1.0
8-PIN SOIC PACKAGE
0.5
0
–50 –40 –30 –20 –10
0 10 20 30 40 50 60
AMBIENT TEMPERATURE – °C
70
80
90
Figure 2. Plot of Maximum Power Dissipation vs.
Temperature
0.045
(1.14)
VOUT
ORDERING GUIDE
–IN
–VS
+IN
Temperature
Range
Package
Package
Description Option*
AD8047AN
AD8047AR
AD8047-EB
–40°C to +85°C
–40°C to +85°C
AD8048AN
AD8048AR
AD8048-EB
–40°C to +85°C
–40°C to +85°C
Plastic DIP
SOIC
Evaluation
Board
Plastic DIP
SOIC
Evaluation
Board
Model
0.044
(1.13)
AD8048
+VS
0.045
–OUT (1.14)
N-8
R-8
N-8
R-8
*N = Plastic DIP; R= SOIC (Small Outline Integrated Circuit)
–IN
+IN
–VS
0.044
(1.13)
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although these devices feature proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
REV. 0
–3–
WARNING!
ESD SENSITIVE DEVICE
AD8047/AD8048
AD8047–Typical Characteristics
RF
10µF
+VS
PULSE
GENERATOR
7
2
AD8047
TR /TF = 500ps
VIN
3
TR/TF = 500ps
6
4
0.1µF
RIN
VIN
VOUT
0.1µF
2
3
10µF
RT = 49.9Ω
7
AD8047
RT = 66.5Ω
RL = 100Ω
10µF
+VS
PULSE
GENERATOR
0.1µF
VOUT
6
0.1µF
4
100Ω
RL = 100Ω
10µF
–VS
–V S
Figure 3. Noninverting Configuration, G = +1
1V
Figure 6. Inverting Configuration, G = –1
5ns
1V
Figure 4. Large Signal Transient Response;
VO = 4 V p-p, G = +1
100mV
5ns
Figure 7. Large Signal Transient Response;
VO = 4 V p-p, G = –1, RF = RIN = 200 Ω
5ns
100mV
Figure 5. Small Signal Transient Response;
VO = 400 mV p-p, G = +1
5ns
Figure 8. Small Signal Transient Response;
VO = 400 mV p-p, G = –1, RF = RIN = 200 Ω
–4–
REV. 0
AD8047/AD8048
AD8048–Typical Characteristics
RF
PULSE
GENERATOR
10µF
+V S
TR/T F = 500ps
2
RIN
VIN
AD8048
3
0.1µF
TR/TF = 500ps
7
VOUT
6
2
RT = 49.9Ω
3
RL = 100Ω
RL = 100Ω
–VS
Figure 9. Noninverting Configuration, G = +2
Figure 12. Inverting Configuration, G= –1
1V
5ns
Figure 10. Large Signal Transient Response;
VO = 4 V p-p, G = +2, RF = RIN = 200 Ω
5ns
Figure 13. Large Signal Transient Response;
VO = 4 V p-p, G = –1, RF = RIN = 200 Ω
5ns
100mV
Figure 11. Small Signal Transient Response;
VO = 400 mV p-p, G = +2, RF = RIN = 200 Ω
REV. 0
4
10µF
–VS
100mV
VOUT
6
0.1µF
RS = 100Ω
10µF
1V
7
AD8048
RT = 66.5Ω
0.1µF
4
10µF
+VS
PULSE
GENERATOR
0.1µF
RIN
VIN
RF
5ns
Figure 14. Small Signal Transient Response;
VO = 400 mV p-p, G = –1, RF = RIN = 200 Ω
–5–
AD8047/AD8048
AD8047–Typical Characteristics
1
0
–1
–1
–3
RL = 100Ω
RF = 0Ω FOR DIP
RF = 66.5Ω FOR SOIC
VOUT = 300mV p-p
–2
OUTPUT – dBm
–2
OUTPUT – dBm
1
0
–4
–5
–6
–3
RL = 100Ω
RF = 0Ω FOR DIP
RF = 66.5Ω FOR SOIC
VOUT = 2V p-p
–4
–5
–6
–7
–7
–8
–8
–9
1M
10M
100M
–9
1M
1G
10M
FREQUENCY – Hz
Figure 15. AD8047 Small Signal Frequency Response
G = +1
1
0
0
–0.1
–1
RL = 100Ω
RF = 0Ω FOR DIP
RF = 66.5Ω FOR SOIC
VOUT = 300mV p-p
–2
OUTPUT – dBm
OUTPUT – dBm
–0.3
–0.4
–0.5
–0.6
–3
RL = 100Ω
RF = RIN = 200Ω
VOUT = 300mV p-p
–4
–5
–6
–0.7
–7
–0.8
–8
–0.9
1M
10M
100M
–9
1M
1G
10M
FREQUENCY – Hz
70
100
60
80
30
20
GAIN
0
–20
10
–40
0
RL = 100Ω
–10
–60
–20
–80
–30
10k
100k
1M
10M
100M
RL = 1kΩ
VOUT = 2V p-p
–40
–50
OUTPUT – dBm
40
PHASE MARGIN – Degrees
GAIN – dB
–20
60
40
20
1G
Figure 19. AD8047 Small Signal Frequency Response,
G = –1
–30
PHASE
MARGIN
50
100M
FREQUENCY – Hz
Figure 16. AD8047 0.1 dB Flatness, G = +1
1k
1G
Figure 18. AD8047 Large Signal Frequency Response,
G = +1
0.1
–0.2
100M
FREQUENCY – Hz
–60
–70
2ND HARMONIC
–80
–90
3RD HARMONIC
–100
–110
–100
1G
–120
10k
FREQUENCY – Hz
100k
1M
10M
100M
FREQUENCY – Hz
Figure 17. AD8047 Open-Loop Gain and Phase Margin vs.
Frequency
Figure 20. AD8047 Harmonic Distortion vs. Frequency,
G = +1
–6–
REV. 0
AD8047/AD8048
–20
0.5
RL = 100Ω
VOUT = 2V p-p
RL = 100Ω
RF = 0Ω
VOUT = 2V STEP
0.4
–40
0.3
–50
0.2
–60
–70
ERROR – %
HARMONIC DISTORTION – dBc
–30
2ND HARMONIC
–80
–90
0.1
0.0
–0.1
–0.2
3RD HARMONIC
–100
–0.3
–110
–0.4
–120
10k
100k
10M
1M
–0.5
100M
0
5
10
FREQUENCY – Hz
Figure 21. AD8047 Harmonic Distortion vs. Frequency,
G = +1
0.15
0.10
–40
–45
3RD HARMONIC
–50
0.00
–0.05
–0.10
–0.15
2ND HARMONIC
–0.20
–0.25
2.5
3.5
4.5
OUTPUT SWING – V p-p
5.5
6.5
0
2
4
8
6
10
12
SETTLING TIME – µs
14
16
18
Figure 25. AD8047 Long-Term Settling Time, G = +1
Figure 22. AD8047 Harmonic Distortion vs. Output Swing,
G = +1
17
0.04
0.02
INPUT NOISE VOLTAGE – nV/√Hz
DIFF GAIN – %
0.05
–55
–65
1.6
0.00
–0.02
–0.04
1st
DIFF PHASE – Degrees
45
RL = 100Ω
RF = 0Ω
VOUT = 2V STEP
0.20
f = 20MHz
RL = 1kΩ
RF = 0Ω
–60
2nd
3rd
4th
5th
6th
7th
8th
9th
10th 11th
0.04
0.02
0.00
15
13
11
9
7
5
–0.02
–0.04
3
1st
2nd
3rd
4th
5th
6th
7th
8th
9th
10th 11th
10
100
1k
FREQUENCY – Hz
10k
Figure 26. AD8047 Noise vs. Frequency
Figure 23. AD8047 Differential Gain and Phase Error,
G = +2, RL = 150 Ω, RF = 200 Ω, RIN = 200 Ω
REV. 0
40
0.25
ERROR – %
HARMONIC DISTORTION – dBc
–35
35
Figure 24. AD8047 Short-Term Settling Time, G = +1
–25
–30
20
15
25
30
SETTLING TIME – ns
–7–
100k
AD8047/AD8048
AD8048–Typical Characteristics
7
7
6
6
5
4
OUTPUT – dBm
OUTPUT – dBm
3
2
1
0
3
2
1
0
–1
–1
–2
–2
–3
–3
1M
10M
100M
FREQUENCY – Hz
1G
1M
10M
1
6.4
RL = 100Ω
RF = RIN = 200Ω
VOUT = 300mV p-p
6.3
0
–1
6.2
OUTPUT – dBm
–2
6.1
6.0
5.9
–4
–5
5.8
–6
–7
5.6
–8
5.5
–9
1M
10M
100M
1G
RL = 100Ω
RF = RIN = 200Ω
VOUT = 300mV p-p
–3
5.7
1M
10M
FREQUENCY – Hz
100
–20
80
80
–30
70
60
HARMONIC DISTORTION – dBc
90
40
50
20
0
40
–20
30
RL = 100Ω
20
–40
10
–60
0
–80
–10
–100
–20
–120
1G
10k
100k
1M
10M
FREQUENCY – Hz
100M
PHASE – Degrees
PHASE
60
100M
FREQUENCY – Hz
1G
Figure 31. AD8048 Small Signal Frequency Response,
G = –1
Figure 28. AD8048 0.1 dB Flatness, G = +2
GAIN – dB
1G
Figure 30. AD8048 Large Signal Frequency Response,
G = +2
6.5
1k
100M
FREQUENCY – Hz
Figure 27. AD8048 Small Signal Frequency Response,
G = +2
OUTPUT – dBm
RL = 100Ω
RF = RIN = 200Ω
VOUT = 2V p-p
5
RL = 100Ω
RF = RIN = 200Ω
VOUT = 300mV p-p
4
RL = 1kΩ
VOUT = 2V p-p
–40
–50
–60
2ND HARMONIC
–70
–80
–90
3RD HARMONIC
–100
–110
–120
10k
Figure 29. AD8048 Open-Loop Gain and Phase Margin vs.
Frequency
100k
1M
FREQUENCY – Hz
10M
100M
Figure 32. AD8048 Harmonic Distortion vs. Frequency,
G = +2
–8–
REV. 0
AD8047/AD8048
0.5
–20
–40
0.3
–50
0.2
–60
0.1
–70
2ND HARMONIC
–80
–0.3
–100
–0.4
–0.5
–120
10k
100k
1M
FREQUENCY – Hz
10M
100M
–15
10
15
20
25
30
35
40
45
0.25
–30
RL = 100Ω
RF = 200Ω
VOUT = 2V STEP
0.20
f = 20MHz
RL = 1kΩ
RF = 200
–25
0.15
3RD HARMONIC
0.10
–35
ERROR – %
HARMONIC DISTORTION – dBc
5
Figure 36. AD8048 Short-Term Settling Time, G = +2
–20
–40
–45
–50
2ND HARMONIC
–55
0.05
0.0
–0.05
–0.10
–60
–0.15
–65
–0.20
–70
1.5
2.5
3.5
4.5
OUTPUT SWING – Volts p-p
5.5
–0.25
6.5
Figure 34. AD8048 Harmonic Distortion vs. Output Swing,
G = +2
0
2
4
8
6
10
12
SETTLING TIME – µs
14
16
18
Figure 37. AD8048 Long-Term Settling Time 2 V Step,
G = +2
17
0.04
0.02
INPUT NOISE VOLTAGE – nV/√Hz
DIFF GAIN – %
0
SETTLING TIME – ns
Figure 33. AD8048 Harmonic Distortion vs. Frequency,
G = +2
0.00
–0.02
–0.04
1st
DIFF PHASE – Degrees
0.0
–0.1
–0.2
3RD HARMONIC
–90
–110
2nd
3rd
4th
5th
6th
7th
8th
9th
10th 11th
0.04
0.02
0.00
15
13
11
9
7
5
–0.02
–0.04
1st
2nd
3rd
4th
5th
6th
7th
8th
9th
3
10th 11th
10
Figure 35. AD8048 Differential Gain and Phase Error,
G = +2, RL = 150 Ω, RF = 200 Ω, RIN = 200 Ω
REV. 0
RL = 100Ω
RF = 200Ω
VOUT = 2V STEP
0.4
ERROR – %
HARMONIC DISTORTION – dBc
–30
RL = 100Ω
VOUT = 2V p-p
100
1k
FREQUENCY – Hz
10k
100k
Figure 38. AD8048 Noise vs. Frequency
–9–
AD8047/AD8048–Typical Characteristics
100
100
∆VCM = 1V
RL = 100Ω
∆VCM = 1V
RL = 100Ω
90
80
80
70
70
CMRR – dB
CMRR – dB
90
60
50
40
60
50
40
30
30
20
100k
1M
100M
10M
20
100k
1G
FREQUENCY – Hz
1M
10M
1G
100M
FREQUENCY – Hz
Figure 42. AD8048 CMRR vs. Frequency
100
100
10
10
ROUT – Ω
ROUT – Ω
Figure 39. AD8047 CMRR vs. Frequency
1
1
0.1
0.1
0.01
10k
100k
1M
10M
100M
0.01
10k
1G
100k
90
90
80
80
+PSRR
1G
–PSRR
+PSRR
60
50
40
50
40
30
30
20
20
10
10
0
10k
100M
70
–PSRR
PSRR – dB
PSRR – dB
60
10M
Figure 43. AD8048 Output Resistance vs. Frequency,
G = +2
Figure 40. AD8047 Output Resistance vs. Frequency,
G = +1
70
1M
FREQUENCY – Hz
FREQUENCY – Hz
0
100k
1M
10M
100M
1G
3k
FREQUENCY – Hz
10k
100k
1M
100M
500M
FREQUENCY – Hz
Figure 41. AD8047 PSRR vs. Frequency
Figure 44. AD8048 PSRR vs. Frequency,
G = +2
–10–
REV. 0
AD8047/AD8048
83.0
4.1
3.9
82.0
RL = 1kΩ
+VOUT
AD8047
–VOUT 
81.0
3.5
CMRR – –dB
OUTPUT SWING – Volts
3.7
3.3
+VOUT
3.1
RL = 150Ω
–VOUT 
80.0
AD8048
79.0
2.9
78.0
2.7
+VOUT
2.5
2.3
–60
–40
–20
77.0
RL = 50Ω
–VOUT 
0
20
40
60
80
100
JUNCTION TEMPERATURE – °C
120
76.0
–60
140
–40
–20
0
20
40
60
80
100
120
140
JUNCTION TEMPERATURE – °C
Figure 45. AD8047/AD8048 Output Swing vs. Temperature
Figure 48. AD8047/AD8048 CMRR vs. Temperature
2600
8.0
2400
7.5
AD8048
AD8048
SUPPLY CURRENT – mA
OPEN-LOOP GAIN – V/V
2200
2000
1800
1600
1400
AD8048
6.0
±5V
AD8047
5.5
±5V
5.0
–40
–20
0
20
40
60
80
100
JUNCTION TEMPERATURE – °C
120
4.5
–60
140
Figure 46. AD8047/AD8048 Open-Loop Gain vs.
Temperature
–40
–20
0
20
40
60
80
100
JUNCTION TEMPERATURE – °C
120
140
Figure 49. AD8047/AD8048 Supply Current vs.
Temperature
94
900
92
INPUT OFFSET VOLTAGE – µV
800
90
+PSRR
88
PSRR – –dB
AD8047
±6V
6.5
AD8047
1200
1000
–60
±6V
7.0
AD8048
86
84
–PSRR
AD8048
+PSRR
AD8047
82
80
AD8048
600
AD8047
500
400
300
200
AD8047
78
700
–PSRR
76
–60
–40
–20
0
20
40
60
80
100
120
100
–60
140
JUNCTION TEMPERATURE – °C
–20
0
20
40
60
80
100
JUNCTION TEMPERATURE – °C
120
140
Figure 50. AD8047/AD8048 Input Offset Voltage vs.
Temperature
Figure 47. AD8047/AD8048 PSRR vs. Temperature
REV. 0
–40
–11–
AD8047/AD8048
For general voltage gain applications, the amplifier bandwidth
can be closely estimated as:
THEORY OF OPERATION
General
The AD8047 and AD8048 are wide bandwidth, voltage feedback amplifiers. Since their open-loop frequency response follows the conventional 6 dB/octave roll-off, their gain bandwidth
product is basically constant. Increasing their closed-loop gain
results in a corresponding decrease in small signal bandwidth.
This can be observed by noting the bandwidth specification
between the AD8047 (gain of 1) and AD8048 (gain of 2).
f 3 dB ≅
Feedback Resistor Choice
The value of the feedback resistor is critical for optimum performance on the AD8047 and AD8048. For maximum flatness at a
gain of 2, RF and RG should be set to 200 Ω for the AD8048.
When the AD8047 is configured as a unity gain follower, RF
should be set to 0 Ω (no feedback resistor should be used) for
the plastic DIP and 66.5 Ω for the SOIC.
G=1+
+VS
RF
This estimation loses accuracy for gains of +2/–1 or lower due
to the amplifier’s damping factor. For these “low gain” cases,
the bandwidth will actually extend beyond the calculated value
(see Closed-Loop BW plots, Figures 15 and 26).
As a rule of thumb, capacitor CF will not be required if:
(RF iRG ) × CI ≤
where NG is the Noise Gain (1 + RF/RG) of the circuit. For
most voltage gain applications, this should be the case.
10µF
RF
7
3
CF
0.1µF
AD8047/48 6
RTERM
2
4
VOUT
0.1µF
II
RG
–VS
3
Pulse Response
10µF
Unlike a traditional voltage feedback amplifier, where the slew
speed is dictated by its front end dc quiescent current and gain
bandwidth product, the AD8047 and AD8048 provide “on demand” current that increases proportionally to the input “step”
signal amplitude. This results in slew rates (1000 V/µs) comparable to wideband current feedback designs. This, combined
with relatively low input noise current (1.0 pA/√Hz), gives the
AD8047 and AD8048 the best attributes of both voltage and
current feedback amplifiers.
0.1µF
VOUT
AD8047/48 6
2
RG
4
0.1µF
RTERM
–VS
10µF
RF
Figure 52. Inverting Operation
When the AD8047 is used in the transimpedance (I to V) mode,
such as in photodiode detection, the value of RF and diode
capacitance (CI) are usually known. Generally, the value of RF
selected will be in the kΩ range, and a shunt capacitor (CF)
across RF will be required to maintain good amplifier stability.
The value of CF required to maintain optimal flatness (<1 dB
Peaking) and settling time can be estimated as:
[
2
CF ≅ (2 ωO CI RF – 1)/ωO RF
2
]
1/2
where ωO is equal to the unity gain bandwidth product of the
amplifier in rad/sec, and CI is the equivalent total input
capacitance at the inverting input. Typically ωO = 800 × 106
rad/sec (see Open-Loop Frequency Response curve, Figure 17).
As an example, choosing RF = 10 kΩ and CI = 5 pF, requires
CF to be 1.1 pF (Note: CI includes both source and parasitic
circuit capacitance). The bandwidth of the amplifier can be
estimated using the CF calculated as:
f 3 dB ≅
VOUT
Figure 53. Transimpedance Configuration
RF
RG
AD8047
RF
+VS
7
CI
10µF
Figure 51. Noninverting Operation
VIN
NG
4 ωO
RG
VIN
G= –
ωO
  R 
2π 1+  F  
  RG  
1.6
2πR F CF
Large Signal Performance
The outstanding large signal operation of the AD8047 and
AD8048 is due to a unique, proprietary design architecture.
In order to maintain this level of performance, the maximum
180 V-MHz product must be observed, (e.g., @ 100 MHz,
VO ≤ 1.8 V p-p) on the AD8047 and 250 V-MHz product on
the AD8048.
Power Supply Bypassing
Adequate power supply bypassing can be critical when optimizing the performance of a high frequency circuit. Inductance in
the power supply leads can form resonant circuits that produce
peaking in the amplifier’s response. In addition, if large current
transients must be delivered to the load, then bypass capacitors
(typically greater than 1 µF) will be required to provide the best
settling time and lowest distortion. A parallel combination of at
least 4.7 µF, and between 0.1 µF and 0.01 µF, is recommended.
Some brands of electrolytic capacitors will require a small series
damping resistor ≈4.7 Ω for optimum results.
Driving Capacitive Loads
The AD8047/AD8048 have excellent cap load drive capability
for high speed op amps as shown in Figures 55 and 57. However, when driving cap loads greater than 25 pF, the best frequency response is obtained by the addition of a small series
resistance. It is worth noting that the frequency response of the
–12–
REV. 0
AD8047/AD8048
circuit when driving large capacitive loads will be dominated by
the passive roll-off of RSERIES and CL.
With a settling time of 30 ns to 0.01% and 13 ns to 0.1%, the
devices are an excellent choice for DAC I/V conversion. The
same characteristics along with low harmonic distortion make
them a good choice for ADC buffering/amplification. With superb linearity at relatively high signal frequencies, the AD8047
and AD8048 are ideal drivers for ADCs up to 12 bits.
RF
RSERIES
AD8047
RL
1kΩ
(1000 V/µs) give higher performance capabilities to these applications over previous voltage feedback designs.
CL
Operation as a Video Line Driver
The AD8047 and AD8048 have been designed to offer outstanding performance as video line drivers. The important
specifications of differential gain (0.01%) and differential phase
(0.02°) meet the most exacting HDTV demands for driving
video loads.
Figure 54. Driving Capacitive Loads
200Ω
200Ω
10µF
+VS
0.1µF
7
2
500mV
3
VIN
5ns
75Ω
CABLE
75Ω
AD8047/
AD8048
75Ω
CABLE
6
VOUT
0.1µF
4
75Ω
75Ω
10µF
Figure 55. AD8047 Large Signal Transient Response;
VO = 2 V p-p, G = +1, RF = 0 Ω, RSERIES = 0 Ω, CL = 27 pF
RF
Figure 58. Video Line Driver
Active Filters
RSERIES
RIN
–VS
AD8048
RL
1kΩ
CL
Figure 56. Driving Capacitive Loads
The wide bandwidth and low distortion of the AD8047 and
AD8048 are ideal for the realization of higher bandwidth active
filters. These characteristics, while being more common in many
current feedback op amps, are offered in the AD8047 and AD8048
in a voltage feedback configuration. Many active filter configurations are not realizable with current feedback amplifiers.
A multiple feedback active filter requires a voltage feedback
amplifier and is more demanding of op amp performance than
other active filter configurations such as the Sallen-Key. In
general, the amplifier should have a bandwidth that is at least
ten times the bandwidth of the filter if problems due to phase
shift of the amplifier are to be avoided.
Figure 59 is an example of a 20 MHz low pass multiple feedback active filter using an AD8048.
VIN
500mV
R1
154Ω
+5V
C1
50pF
R4
154Ω
R3
78.7Ω
C2
100pF
0.1µF
1
7
2
5ns
10µF
AD8048
100Ω
5
3
6
0.1µF
4
Figure 57. AD8048 Large Signal Transient Response;
VO = 2 V p-p, G = +2, RF = RIN = 200 Ω, RSERIES = 0 Ω,
CL = 27 pF
10µF
–5V
Figure 59. Active Filter Circuit
APPLICATIONS
The AD8047 and AD8048 are voltage feedback amplifiers well
suited for such applications as photodetectors, active filters, and
log amplifiers. The devices’ wide bandwidth (260 MHz), phase
margin (65°), low noise current (1.0 pA/√Hz), and slew rate
REV. 0
Choose:
FO = Cutoff Frequency = 20 MHz
α = Damping Ratio = 1/Q = 2
–13–
VOUT
AD8047/AD8048
–R4
R1 = 1
H = Absolute Value of Circuit Gain =
The PCB should have a ground plane covering all unused portions of the component side of the board to provide a low impedance path. The ground plane should be removed from the
area near the input pins to reduce stray capacitance.
Then:
k = 2 π FO C1
4 C1(H +1)
α2
α
R1 =
2 HK
α
R3 =
2 K (H +1)
R4 = H(R1)
Chip capacitors should be used for the supply bypassing (see
Figure 60). One end should be connected to the ground plane
and the other within 1/8 inch of each power pin. An additional
large (0.47 µF–10 µF) tantalum electrolytic capacitor should be
connected in parallel, though not necessarily so close, to supply
current for fast, large signal changes at the output.
C2 =
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the inverting input will significantly affect high speed performance.
A/D Converter Driver
As A/D converters move toward higher speeds with higher resolutions, there becomes a need for high performance drivers that
will not degrade the analog signal to the converter. It is desirable from a system’s standpoint that the A/D be the element in
the signal chain that ultimately limits overall distortion. This
places new demands on the amplifiers used to drive fast, high
resolution A/Ds.
Stripline design techniques should be used for long signal traces
(greater than about 1 inch). These should be designed with a
characteristic impedance of 50 Ω or 75 Ω and be properly terminated at each end.
Evaluation Board
An evaluation board for both the AD8047 and AD8048 is available that has been carefully laid out and tested to demonstrate
that the specified high speed performance of the device can be
realized. For ordering information, please refer to the Ordering
Guide.
With high bandwidth, low distortion and fast settling time the
AD8047 and AD8048 make high performance A/D drivers for
advanced converters. Figure 60 is an example of an AD8047
used as an input driver for an AD872, a 12-bit, 10 MSPS A/D
converter.
The layout of the evaluation board can be used as shown or
serve as a guide for a board layout.
Layout Considerations
The specified high speed performance of the AD8047 and
AD8048 requires careful attention to board layout and component selection. Proper RF design techniques and low pass parasitic component selection are mandatory
+5V DIGITAL
+5V ANALOG
10Ω
DV DD
4
DGND
AV DD
0.1µF
+5V ANALOG
5
DRV DD
AGND
DRGND
10µF
CLK
AD872
0.1µF
1
7
2
AD8047
ANALOG IN
OTR
3
5
1
6
MSB
BIT2
BIT3
BIT4
BIT5
BIT6
BIT7
BIT8
BIT9
BIT10
BIT11
BIT12
VINA
0.1µF
4
2
VINB
27
–5V
ANALOG
10µF
REF GND
0.1µF
28
REF IN
26
1µF
AGND
REF OUT
AV SS
7
6
0.1µF
+5V DIGITAL
22
23
0.1µF
CLOCK INPUT
21
20
19
18
17
16
15
14
13
12
11
10
9
8
49.9Ω
DIGITAL OUTPUT
24
AV SS
3
25
0.1µF
0.1µF
–5V ANALOG
Figure 60. AD8047 Used as Driver for an AD872, a 12-Bit, 10 MSPS A/D Converter
–14–
REV. 0
AD8047/AD8048
RF
+VS
+V S
RG
RO
OPTIONAL
OUT
IN
RT
–VS
C1
1000pF
C3
0.1µF
C5
10µF
C2
1000pF
C4
0.1µF
C6
10µF
–V S
Supply Bypassing
Noninverting Configuration
Figure 61. Noninverting Configurations for Evaluation Boards
Table I.
AD8047
+2
Component
–1
+1
RF
RG
RO
RS
RT
Small Signal
BW (–3 dB)
200 Ω
200 Ω
49.9 Ω
–
66.5 Ω
66.5 Ω
–
49.9 Ω
0Ω
49.9 Ω
90 MHz
260 MHz 95 MHz
1 kΩ
1 kΩ
49.9 Ω
0Ω
49.9 Ω
AD8048
+10
+10
+101
–1
+2
1 kΩ
110 Ω
49.9 Ω
0Ω
49.9 Ω
1 kΩ
10 Ω
49.9 Ω
0Ω
49.9 Ω
200 Ω
200 Ω
49.9 Ω
–
66.5 Ω
200 Ω
200 Ω
49.9 Ω
0Ω
49.9 Ω
10 MHz
1 MHz
250 MHz 250 MHz 22 MHz
1 kΩ
110 Ω
49.9 Ω
0Ω
49.9 Ω
+101
1 kΩ
10 Ω
49.9 Ω
0Ω
49.9 Ω
2 MHz
SOIC (R)
NONINVERTER
SOIC (R)
INVERTER
Figure 62. Evaluation Board Silkscreen (Top)
SOIC (R)
INVERTER
SOIC (R)
NONINVERTER
Figure 63. Board Layout (Solder Side)
REV. 0
–15–
C1995–10–1/95
AD8047/AD8048
SOIC (R)
NONINVERTER
SOIC (R)
INVERTER
Figure 64. Board Layout (Component Side)
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Pin Plastic DIP
(N Package)
8
5
0.280 (7.11)
0.240 (6.10)
PIN 1
1
4
0.325 (8.25)
0.300 (7.62)
0.430 (10.92)
0.348 (8.84)
0.060 (1.52)
0.015 (0.38)
0.210
(5.33)
MAX
0.195 (4.95)
0.115 (2.93)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.022 (0.558)
0.014 (0.356)
0.100
(2.54)
BSC
0.070 (1.77)
0.045 (1.15)
0.015 (0.381)
0.008 (0.204)
SEATING
PLANE
8-Pin Plastic SOIC
(R Package)
0.150 (3.81)
8
5
0.244 (6.20)
0.228 (5.79)
1
PRINTED IN U.S.A.
PIN 1
0.157 (3.99)
0.150 (3.81)
4
0.197 (5.01)
0.189 (4.80)
0.102 (2.59)
0.094 (2.39)
0.010 (0.25)
0.004 (0.10)
0.050
(1.27)
BSC
0.019 (0.48)
0.014 (0.36)
0.020 (0.051) x 45 °
CHAMF
0.190 (4.82)
0.170 (4.32)
8°
0°
0.090
(2.29)
10 °
0°
0.098 (0.2482)
0.075 (0.1905)
–16–
0.030 (0.76)
0.018 (0.46)
REV. 0
Similar pages