TI LM2852YMXAX-3.0 Lm2852 2a 500/1500khz synchronous simple switcherâ® buck regulator Datasheet

LM2852
www.ti.com
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
LM2852 2A 500/1500kHz Synchronous SIMPLE SWITCHER® Buck Regulator
Check for Samples: LM2852
FEATURES
DESCRIPTION
•
•
The LM2852 SIMPLE SWITCHER® synchronous
buck regulator is a high frequency step-down
switching voltage regulator capable of driving up to a
2A load with excellent line and load regulation. The
LM2852 can accept an input voltage between 2.85V
and 5.5V and deliver an output voltage that is factory
programmable from 0.8V to 3.3V in 100mV
increments. The LM2852 is available with a choice of
two switching frequencies - 500kHz (LM2852Y) or
1.5MHz (LM2852X). It also features internal, typethree compensation to deliver a low component count
solution. The exposed-pad HTSSOP-14 package
enhances the thermal performance of the LM2852.
1
2
•
•
•
•
•
•
•
Input Voltage Range of 2.85 to 5.5V
Factory EEPROM Set Output Voltages from
0.8V to 3.3V in 100mV Increments
Maximum Load Current of 2A
Voltage Mode Control
Internal Type-Three Compensation
Switching Frequency of 500kHz or 1.5MHz
Low Standby Current of 10µA
Internal 60 mΩ MOSFET Switches
Standard Voltage Options
0.8/1.0/1.2/1.5/1.8/2.5/3.3 Volts
APPLICATIONS
•
•
•
•
Low Voltage Point of Load Regulation
Local Solution for FPGA/DSP/ASIC Core
Power
Broadband Networking and Communications
Infrastructure
Portable Computing
Typical Application Circuit
VIN = 3.3V
PVIN
CIN = 22 PF
AVIN
EN
SS
LM2852Y
SNS
VOUT = 2.5V
ILOAD = 0A to 2A
SW
SGND
PGND
LO = 10 PH
+
CO = 100 PF
CSS = 2.7 nF
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2013, Texas Instruments Incorporated
LM2852
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
www.ti.com
Figure 1. Efficiency vs ILOAD
96
PVIN = 3.3V
EFFICIENCY (%)
94
92
90
88
86
84
0.1
1.0
10
ILOAD (A)
Connection Diagram
AVIN
1
14
SNS
EN
2
13
NC
SGND
3
12
NC
11
PGND
LM2852
SS
4
NC
5
10
PGND
PVIN
6
9
SW
PVIN
7
8
SW
Figure 2. 14-Pin HTSSOP – Top View
See Package Number PWP0014A
PIN DESCRIPTIONS
AVIN (Pin 1): Chip bias input pin. This provides power to the logic of the chip. Connect to the input voltage or a separate rail.
EN (Pin 2): Enable. Connect this pin to ground to disable the chip; connect to AVIN or leave floating to enable the chip; enable is internally
pulled up.
SGND (Pin 3): Signal ground.
SS (Pin 4): Soft-start pin. Connect this pin to a small capacitor to control startup. The soft-start capacitance range is restricted to values 1
nF to 50 nF.
NC (Pins 5, 12 and 13): No connect. These pins must be tied to ground or left floating in the application.
PVIN (Pins 6, 7): Input supply pin. PVIN is connected to the input voltage. This rail connects to the source of the internal power PFET.
SW (Pins 8, 9): Switch pin. Connect to the output inductor.
PGND (Pins 10, 11): Power ground. Connect this to an internal ground plane or other large ground plane.
SNS (Pin 14): Output voltage sense pin. Connect this pin to the output voltage as close to the load as possible.
Exposed Pad: Connect to ground.
2
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
LM2852
www.ti.com
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2)
−0.3V to 6.5V
PVIN, AVIN, EN, SNS
ESD Susceptibility (3)
2kV
Power Dissipation
Internally Limited
Storage Temperature Range
−65°C to +150°C
Maximum Junction Temp.
14-Pin Exposed Pad HTSSOP Package
150°C
Infrared (15 sec)
220°C
Vapor Phase (60 sec)
215°C
Soldering (10 sec)
(1)
(2)
(3)
260°C
Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Range indicates conditions for
which the device is intended to be functional, but does not ensure specfic performance limits. For ensured specifications and test
conditions, see the Electrical Characteristics.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Human body model: 1.5kΩ in series with 100pF. SW and PVIN pins are derated to 1.5kV
Operating Ratings (1)
PVIN to GND
1.5V to 5.5V
AVIN to GND
2.85V to 5.5V
−40°C to +125°C
Junction Temperature
θJA
(1)
38°C/W
Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Range indicates conditions for
which the device is intended to be functional, but does not ensure specfic performance limits. For ensured specifications and test
conditions, see the Electrical Characteristics.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
3
LM2852
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
www.ti.com
Electrical Characteristics
AVIN = PVIN = 5V unless otherwise indicated under the Conditions column. Limits in standard type are for TJ = 25°C only;
limits in boldface type apply over the junction temperature (TJ) range of -40°C to +125°C. Minimum and Maximum limits are
ensured through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C,
and are provided for reference purposes only.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
SYSTEM PARAMETERS
VOUT
Voltage
Tolerance (1)
ΔVOUT/ΔAVIN
Line Regulation (1)
VOUT = 0.8V option
0.782
0.818
VOUT = 1.0V option
0.9775
1.0225
VOUT = 1.2V option
1.1730
1.2270
VOUT = 1.5V option
1.4663
1.5337
VOUT = 1.8V option
1.7595
1.8405
VOUT = 2.5V option
2.4437
2.5563
VOUT = 3.0V option
2.9325
3.0675
VOUT = 3.3V option
3.2257
3.3743
V
VOUT = 0.8V, 1.0V, 1.2V, 1.5V, 1.8V or 2.5V
2.85V ≤ AVIN ≤ 5.5V
0.2
0.6
%
VOUT = 3.3V
3.5V ≤ AVIN ≤ 5.5V
0.2
0.6
%
ΔVOUT/ΔIO
Load Regulation
Normal operation
VON
UVLO Threshold
(AVIN)
Rising
Falling Hysteresis
8
85
mV/A
2.47
2.85
V
150
210
mV
rDSON-P
PFET On
Resistance
Isw = 2A
75
140
mΩ
rDSON-N
NFET On
Resistance
Isw = 2A
55
120
mΩ
RSS
Soft-start resistance
ICL
Peak Current Limit
Threshold
LM2852X
2.75
4
4.95
LM2852Y
2.25
3
3.65
Operating Current
Non-switching
0.85
2
mA
Shutdown Quiescent
EN = 0V
Current
10
25
µA
RSNS
Sense pin resistance
400
fosc
LM2852X
1500kHz option.
1050
1500
1825
kHz
LM2852Y
500kHz option.
325
500
625
kHz
100
%
IQ
ISD
400
kΩ
A
kΩ
PWM
Drange
Duty Cycle Range
0
ENABLE CONTROL (2)
VIH
EN Pin Minimum
High Input
VIL
EN Pin Maximum
Low Input
IEN
EN Pin Pullup
Current
% of
AVIN
75
25
EN = 0V
% of
AVIN
1.2
µA
THERMAL CONTROLS
(1)
(2)
4
TSD
TJ for Thermal
Shutdown
165
°C
TSD-HYS
Hysteresis for
Thermal Shutdown
10
°C
VOUT measured in a non-switching, closed-loop configuration at the SNS pin.
The enable pin is internally pulled up, so the LM2852 is automatically enabled unless an external enable voltage is applied.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
LM2852
www.ti.com
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
LM2852Y Typical Performance Characteristics (500kHz)
Efficiency vs ILoad VOUT = 1.5V
Efficiency vs ILoad VOUT = 2.5V
92
96
PVIN = 3.3V
PVIN = 3.3V
90
94
86
84
92
EFFICIENCY (%)
EFFICIENCY (%)
88
PVIN = 5.0V
82
90
PVIN = 5.0V
88
80
86
78
84
76
0.1
1.0
0.1
10
1.0
10
ILOAD (A)
ILOAD (A)
Figure 3.
Figure 4.
Efficiency vs ILoad VOUT = 3.3V
Frequency vs Temperature
95
560
94
550
VIN = 3.3V
PVIN = 5.0V
540
FREQUENCY (kHz)
EFFICIENCY (%)
93
92
91
90
530
520
510
89
500
88
490
87
0.1
1.0
10
480
-50
VIN = 5V
-25
0
25
50
75
100 125 150
TEMPERATURE (oC)
ILOAD (A)
Figure 5.
Figure 6.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
5
LM2852
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
www.ti.com
LM2852X Typical Performance Characteristics (1500kHz)
Efficiency vs ILoad VOUT = 1.5V
Efficiency vs ILoad VOUT = 2.5V
100
85
PVIN = 3.3V
PVIN = 3.3V
80
90
70
65
60
80
EFFICIENCY (%)
EFFICIENCY (%)
75
PVIN = 5.0V
PVIN = 5.0V
70
60
55
50
50
45
0.1
1.0
40
0.1
10
ILOAD (A)
Figure 7.
Figure 8.
Efficiency vs ILoad VOUT = 3.3V
Frequency vs Temperature
1600
85
1550
FREQUENCY (kHz)
EFFICIENCY (%)
80
PVIN = 5.0V
70
65
60
1500
1450
PVIN = 5.0V
1400
1350
1300
1.0
10
1200
-50 -25
0
25
50
75
80
85
90
o
TEMPERATURE ( C)
ILOAD (A)
Figure 9.
6
PVIN = 3.3V
1250
55
50
0.1
10
ILOAD (A)
90
75
1.0
Figure 10.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
LM2852
www.ti.com
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
LM2852 Typical Performance Characteristics (Both Y and X Versions)
Shutdown Current vs VIN
Quiescent Current (Non-Switching) vs VIN
1100
17
1000
15
125oC
900
13
o
85 C
IQ (PA)
IQ SHUTDOWN (PA)
125oC
11
o
800
85oC
25 C
25oC
700
9
-40oC
7
5
2.5
3
3.5
4
4.5
5
-40oC
600
500
2.5
5.5
3
3.5
4
4.5
5
5.5
VIN (V)
VIN (V)
Figure 11.
Figure 12.
NMOS Switch RDSON vs Temperature
PMOS Switch RDSON vs Temperature
100
130
120
90
PFET RDSON (m:)
NFET RDSON (m:)
110
80
PVIN = 3.3V
70
PVIN = 5.0V
60
PVIN = 3.3V
100
90
PVIN = 5.0V
80
70
50
60
40
-50
-25
0
25
50
75
100 125 150
TEMPERATURE (oC)
50
-50
-25
0
25
50
75
100 125 150
TEMPERATURE (oC)
Figure 13.
Figure 14.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
7
LM2852
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
www.ti.com
Block Diagram
SGND
PVIN
Reference
Oscillator
UVLO
DAC
AVIN
Current Limit
Ramp and Clock
Generator
400 k:
EN
Gate
Drive
Error
Amp
SS
+
20 pF
200 k:
200 k:
Zc1
Zc2
SW
+
PWM
Comp
PGND
SNS
8
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
LM2852
www.ti.com
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
APPLICATIONS INFORMATION
The LM2852 is a DC-DC synchronous buck regulator belonging to Texas Instrument’s SIMPLE SWITCHER
family. Integration of the PWM controller, power switches and compensation network greatly reduces the
component count required to implement a switching power supply. A typical application requires only four
components: an input capacitor, a soft-start capacitor, an output filter capacitor and an output filter inductor.
INPUT CAPACITOR (CIN)
Fast switching of large currents in the buck converter places a heavy demand on the voltage source supplying
PVIN. The input capacitor, CIN, supplies extra charge when the switcher needs to draw a burst of current from
the supply. The RMS current rating and the voltage rating of the CIN capacitor are therefore important in the
selection of CIN. The RMS current specification can be approximated by:
IRMS = ILOAD
D(1-D)
where
•
D is the duty cycle, VOUT/VIN. CIN also provides filtering of the supply.
(1)
Trace resistance and inductance degrade the benefits of the input capacitor, so CIN should be placed very close
to PVIN in the layout. A 22 µF or 47 µF ceramic capacitor is typically sufficient for CIN. In parallel with the large
input capacitance a smaller capacitor may be added such as a 1µF ceramic for higher frequency filtering.
SOFT-START CAPACITOR (CSS)
The DAC that sets the reference voltage of the error amp sources a current through a resistor to set the
reference voltage. The reference voltage is one half of the output voltage of the switcher due to the 200kΩ
divider connected to the SNS pin. Upon start-up, the output voltage of the switcher tracks the reference voltage
with a two to one ratio as the DAC current charges the capacitance connected to the reference voltage node.
Internal capacitance of 20pF is permanently attached to the reference voltage node which is also connected to
the soft-start pin, SS. Adding a soft-start capacitor externally increases the time it takes for the output voltage to
reach its final level.
The charging time required for the reference voltage can be estimated using the RC time constant of the DAC
resistor and the capacitance connected to the SS pin. Three RC time constant periods are needed for the
reference voltage to reach 95% of its final value. The actual start-up time will vary with differences in the DAC
resistance and higher-order effects.
If little or no soft-start capacitance is connected, then the start-up time may be determined by the time required
for the current limit current to charge the output filter capacitance. The capacitor charging equation I = C ΔV/Δt
can be used to estimate the start-up time in this case. For example, a part with a 3V output, a 100 µF output
capacitance and a 3A current limit threshold would require a time of 100 µs:
't = C
'V
3V
= 100 PF
= 100 Ps
I
3A
(2)
Since it is undesirable for the power supply to start up in current limit, a soft-start capacitor must be chosen to
force the LM2852 to start up in a more controlled fashion based on the charging of the soft-start capacitance. In
this example, suppose a 3 ms start time is desired. Three time constants are required for charging the soft-start
capacitor to 95% of the final reference voltage. So in this case RC=1ms. The DAC resistor, R, is 400 kΩ so C
can be calculated to be 2.5nF. A 2.7nF ceramic capacitor can be chosen to yield approximately a 3ms start-up
time.
SOFT-START CAPACITOR (CSS) AND FAULT CONDITIONS
Various fault conditions such as short circuit and UVLO of the LM2852 activate internal circuitry designed to
control the voltage on the soft-start capacitor. For example, during a short circuit current limit event, the output
voltage typically falls to a low voltage. During this time, the soft-start voltage is forced to track the output so that
once the short is removed, the LM2852 can restart gracefully from whatever voltage the output reached during
the short circuit event. The range of soft-start capacitors is therefore restricted to values 1nF to 50nF.
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
9
LM2852
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
www.ti.com
COMPENSATION
The LM2852 provides a highly integrated solution to power supply design. The compensation of the LM2852,
which is type-three, is included on-chip. The benefit to integrated compensation is straightforward, simple power
supply design. Since the output filter capacitor and inductor values impact the compensation of the control loop,
the range of L, C and CESR values is restricted in order to ensure stability.
OUTPUT FILTER VALUES
Table 1 details the recommended inductor and capacitor ranges for the LM2852 that are suggested for various
typical output voltages. Values slightly different than those recommended may be used, however the phase
margin of the power supply may be degraded.
Table 1. Output Filter Values
Frequency Option
LM2852Y
(500kHz)
LM2852X
(1500kHz)
10
VOUT (V)
PVIN (V)
L (µH)
C (µF)
CESR (mΩ)
Min
Max
Min
Max
Min
Max
0.8
3.3
10
15
100
220
70
200
0.8
5.0
10
15
100
120
70
200
1.0
3.3
10
15
100
180
70
200
1.0
5.0
10
15
100
180
70
200
1.2
3.3
10
15
100
180
70
200
1.2
5.0
15
22
100
120
70
200
1.5
3.3
10
15
100
120
70
200
1.5
5.0
22
22
100
120
70
200
1.8
3.3
10
15
100
120
100
200
1.8
5.0
22
33
100
120
100
200
2.5
3.3
6.8
10
68
120
95
275
2.5
5.0
15
22
68
120
95
275
3.3
5.0
15
22
68
100
100
275
0.8
3.3
0.8
5.0
1.0
3.3
1.0
5.0
1.2
3.3
1.2
5.0
1.5
3.3
1.5
5.0
1.8
3.3
1.8
5.0
2.5
3.3
2.5
5.0
3.3
5.0
The 1500kHz version is
designed for ceramic output
capacitors which typically have
very low ESR (<10mΩ.)
1
Submit Documentation Feedback
10
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
LM2852
www.ti.com
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
CHOOSING AN INDUCTANCE VALUE
The current ripple present in the output filter inductor is determined by the input voltage, output voltage, switching
frequency and inductance according to the following equation:
'IL =
D x (VIN - VOUT)
fxL
where
•
•
•
•
•
•
ΔIL is the peak-to-peak current ripple.
D is the duty cycle VOUT/VIN.
VIN is the input voltage applied to the PVIN pin.
VOUT is the output voltage of the switcher.
f is the switching frequency.
L is the inductance of the output filter inductor.
(3)
Knowing the current ripple is important for inductor selection since the peak current through the inductor is the
load current plus one half the ripple current. Care must be taken to ensure the peak inductor current does not
reach a level high enough to trip the current limit circuitry of the LM2852.
As an example, consider a 5V to 1.2V conversion and a 500kHz switching frequency. According to Table 1, a
15µH inductor may be used. Calculating the expected peak-to-peak ripple,
'IL =
1.2V
x (5V - 1.2V)
5V
500 kHz x 15 PH
= 121.6 mA
(4)
The maximum inductor current for a 2A load would therefore be 2A plus 60.8 mA, 2.0608A. As shown in the
ripple equation, the current ripple is inversely proportional to inductance.
OUTPUT FILTER INDUCTORS
Once the inductance value is chosen, the key parameter for selecting the output filter inductor is its saturation
current (Isat) specification. Typically Isat is given by the manufacturer as the current at which the inductance of the
coil falls to a certain percentage of the nominal inductance. The Isat of an inductor used in an application should
be greater than the maximum expected inductor current to avoid saturation. Below is a table of inductors that
may be suitable in LM2852 applications.
Table 2. LM2852 Output Filter Inductors
Inductance (µH)
Part Number
Vendor
1
DO1608C-102
Coilcraft
1
DO1813P-102HC
Coilcraft
6.8
DO3316P-682
Coilcraft
7
MSS1038-702NBC
Coilcraft
10
DO3316P-103
Coilcraft
10
MSS1038-103NBC
Coilcraft
12
MSS1038-123NBC
Coilcraft
15
D03316P-153
Coilcraft
15
MSS1038-153NBC
Coilcraft
18
MSS1038-183NBC
Coilcraft
22
DO3316P-223
Coilcraft
22
MSS1038-223NBC
Coilcraft
22
DO3340P-223
Coilcraft
27
MSS1038-273NBC
Coilcraft
33
MSS1038-333NBC
Coilcraft
33
DO3340P-333
Coilcraft
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
11
LM2852
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
www.ti.com
OUTPUT FILTER CAPACITORS
The capacitors that may be used in the output filter with the LM2852 are limited in value and ESR range
according to Table 1. Below are some examples of capacitors that can typically be used in an LM2852
application.
Table 3. LM2852 Output Filter Capacitors
Capacitance (µF)
Part Number
Chemistry
Vendor
10
GRM31MR61A106KE19
Ceramic
Murata
10
GRM32DR61E106K
Ceramic
Murata
68
595D686X_010C2T
Tantalum
Vishay - Sprague
68
595D686X_016D2T
Tantalum
Vishay - Sprague
100
595D107X_6R3C2T
Tantalum
Vishay - Sprague
100
595D107X_016D2T
Tantalum
Vishay - Sprague
100
NOSC107M004R0150
Niobium Oxide
AVX
100
NOSD107M006R0100
Niobium Oxide
AVX
120
595D127X_004C2T
Tantalum
Vishay - Sprague
120
595D127X_010D2T
Tantalum
Vishay - Sprague
150
595D157X_004C2T
Tantalum
Vishay - Sprague
150
595D157X_016D2T
Tantalum
Vishay - Sprague
150
NOSC157M004R0150
Niobium Oxide
AVX
150
NOSD157M006R0100
Niobium Oxide
AVX
220
595D227X_004D2T
Tantalum
Vishay - Sprague
220
NOSD227M004R0100
Niobium Oxide
AVX
220
NOSE227M006R0100
Niobium Oxide
AVX
SPLIT-RAIL OPERATION
The LM2852 can be powered using two separate voltages for AVIN and PVIN. AVIN is the supply for the control
logic; PVIN is the supply for the power FETs. The output filter components need to be chosen based on the
value of PVIN. For PVIN levels lower than 3.3V, use output filter component values recommended for 3.3V. PVIN
must always be equal to or less than AVIN.
PVIN = 3.3V
AVIN = 5V
PVIN
CIN = 47 PF
1 PF
AVIN
EN
SS
LM2852Y
SNS
VOUT = 1.5V
ILOAD = 0A to 2A
SW
SGND
PGND
LO = 10 PH
+
CO = 100 PF
CSS = 3.3 nF
SWITCH NODE PROTECTION
The LM2852 includes protection circuitry that monitors the voltage on the switch pin. Under certain conditions,
switching is disabled in order to protect the switching devices. One result of the protection circuitry may be
observed when power to the LM2852 is applied with no or light load on the output. The output regulates to the
rated voltage, but no switching may be observed. As soon as the output is loaded, the LM2852 begins normal
switching operation.
LAYOUT HINTS
These are several guidelines to follow while designing the PCB layout for an LM2852 application.
1. The input bulk capacitor, CIN, should be placed very close to the PVIN pin to keep the resistance as low as
possible between the capacitor and the pin. High current levels will be present in this connection.
12
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
LM2852
www.ti.com
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
2. All ground connections must be tied together. Use a broad ground plane, for example a completely filled
back plane, to establish the lowest resistance possible between all ground connections.
3. The sense pin connection should be made as close to the load as possible so that the voltage at the load is
the expected regulated value. The sense line should not run too close to nodes with high EMI (such as the
switch node) to minimize interference.
4. The switch node connections should be low resistance to reduce power losses. Low resistance means the
trace between the switch pin and the inductor should be wide. However, the area of the switch node should
not be too large since EMI increases with greater area. So connect the inductor to the switch pin with a short,
but wide trace. Other high current connections in the application such as PVIN and VOUT assume the same
trade off between low resistance and EMI.
5. Allow area under the chip to solder the entire exposed die attach pad to ground for improved thermal and
electrical performance.
LM2852 Example Circuit Schematic
VIN = 3.3V
U1
PVIN
Rf
CINX
AVIN
EN
Cf
CIN
SS
LM2852
SNS
VOUT = 1.8V
ILOAD = 0A to 2A
SW
SGND
PGND
LO
+
CO
CSS
Figure 15.
Table 4. Bill of Materials for 500kHz (LM2852Y) 3.3VIN to 1.8 VOUT Conversion
ID
Part Number
U1
LM2852YMXA-1.8
Type
Size
2A Buck
HTSSOP-14
Inductor
Parameters
Qty
Vendor
1
TI
LO
DO3316P-153
15 µH
1
Coilcraft
CO*
595D107X_6R3C2T
Capacitor
Case Code “C”
100 µF ±20%
1
Vishay-Sprague
CIN
GRM32ER60J476ME20B
Capacitor
1210
47µF/X5R/6.3V
1
Murata
CINX
GRM21BR71C105KA01B
Capacitor
0805
1µF/X7R/16V
1
Murata
CSS
VJ0805Y272KXXA
Capacitor
0805
2.7nF ±10%
1
Vishay-Vitramon
Rf
CRCW060310R0F
Resistor
0603
10Ω ±10%
1
Vishay-Dale
Cf
GRM21BR71C105KA01B
Capacitor
0805
1µF/X7R/16V
1
Murata
Table 5. Bill of Materials for 1500kHz (LM2852X) 3.3V to 1.8V Conversion
Type
Size
U1
ID
LM2852XMXA-1.8
Part Number
2A Buck
HTSSOP-14
L0
DO1813P-102HC
Inductor
Parameters
Qty
Vendor
1
TI
1 µH
1
Coilcraft
C0
GRM32DR61E106K
Capacitor
1210
10 µF/X5R/25V
1
Murata
CIN
GRM32ER60J476ME20B
Capacitor
1210
47µF/X5R/6.3V
1
Murata
CINX
GRM21BR71C105KA01B
Capacitor
0805
1µF/X7R/16V
1
Murata
CSS
VJ0805Y272KXXA
Capacitor
0805
2.7nF ±10%
1
Vishay-Vitramon
Rf
CRCW060310R0F
Resistor
0603
10Ω ±10%
1
Vishay-Dale
Cf
GRM21BR71C105KA01B
Capacitor
0805
1µF/X7R/16V
1
Murata
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
13
LM2852
SNVS325D – JANUARY 2005 – REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision C (April 2013) to Revision D
•
14
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 13
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM2852
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2852XMXA-0.8/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
0.8
LM2852XMXA-1.0/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
1.0
LM2852XMXA-1.2
NRND
HTSSOP
PWP
14
94
TBD
Call TI
Call TI
-40 to 125
2852X
1.2
LM2852XMXA-1.2/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
1.2
LM2852XMXA-1.5
NRND
HTSSOP
PWP
14
94
TBD
Call TI
Call TI
-40 to 125
2852X
1.5
LM2852XMXA-1.5/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
1.5
LM2852XMXA-1.8/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
1.8
LM2852XMXA-2.5
NRND
HTSSOP
PWP
14
94
TBD
Call TI
Call TI
-40 to 125
2852X
2.5
LM2852XMXA-2.5/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
2.5
LM2852XMXA-3.0/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2852XMXA-3.3/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
3.3
LM2852XMXAX-0.8/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
0.8
LM2852XMXAX-1.0/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
1.0
LM2852XMXAX-1.2/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
1.2
LM2852XMXAX-1.5/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
1.5
LM2852XMXAX-1.8/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
1.8
LM2852XMXAX-2.5
NRND
HTSSOP
PWP
14
2500
TBD
Call TI
Call TI
-40 to 125
2852X
2.5
Addendum-Page 1
2852X
3.0
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
1-Nov-2013
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2852XMXAX-2.5/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2852XMXAX-3.0/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2852XMXAX-3.3/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852X
3.3
LM2852YMXA-0.8/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-0.8
LM2852YMXA-1.0/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-1.0
LM2852YMXA-1.2
NRND
HTSSOP
PWP
14
94
TBD
Call TI
Call TI
-40 to 125
2852Y
-1.2
LM2852YMXA-1.2/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-1.2
LM2852YMXA-1.3/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2852YMXA-1.5/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-1.5
LM2852YMXA-1.8
NRND
HTSSOP
PWP
14
94
TBD
Call TI
Call TI
-40 to 125
2852Y
-1.8
LM2852YMXA-1.8/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-1.8
LM2852YMXA-2.5/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-2.5
LM2852YMXA-3.0/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2852YMXA-3.3
NRND
HTSSOP
PWP
14
94
TBD
Call TI
Call TI
-40 to 125
2852Y
-3.3
LM2852YMXA-3.3/NOPB
ACTIVE
HTSSOP
PWP
14
94
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-3.3
LM2852YMXAX-0.8/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-0.8
LM2852YMXAX-1.0/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-1.0
LM2852YMXAX-1.2/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-1.2
Addendum-Page 2
-40 to 125
2852X
2.5
2852X
3.0
2852Y
1.3
2852Y
3.0
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
1-Nov-2013
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM2852YMXAX-1.3/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
2852Y
1.3
LM2852YMXAX-1.5/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-1.5
LM2852YMXAX-1.8/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-1.8
LM2852YMXAX-2.5/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
2852Y
-2.5
LM2852YMXAX-3.0/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM2852YMXAX-3.3/NOPB
ACTIVE
HTSSOP
PWP
14
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
2852Y
3.0
-40 to 125
2852Y
-3.3
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM2852XMXAX-0.8/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852XMXAX-1.0/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852XMXAX-1.2/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852XMXAX-1.5/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852XMXAX-1.8/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
HTSSOP
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852XMXAX-2.5/NOP HTSSOP
B
LM2852XMXAX-2.5
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852XMXAX-3.0/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852XMXAX-3.3/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852YMXAX-0.8/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852YMXAX-1.0/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM2852YMXAX-1.2/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852YMXAX-1.3/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852YMXAX-1.5/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852YMXAX-1.8/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852YMXAX-2.5/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852YMXAX-3.0/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
LM2852YMXAX-3.3/NOP HTSSOP
B
PWP
14
2500
330.0
12.4
6.95
8.3
1.6
8.0
12.0
Q1
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM2852XMXAX-0.8/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852XMXAX-1.0/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852XMXAX-1.2/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852XMXAX-1.5/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852XMXAX-1.8/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM2852XMXAX-2.5
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852XMXAX-2.5/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852XMXAX-3.0/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852XMXAX-3.3/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852YMXAX-0.8/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852YMXAX-1.0/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852YMXAX-1.2/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852YMXAX-1.3/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852YMXAX-1.5/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852YMXAX-1.8/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852YMXAX-2.5/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852YMXAX-3.0/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
LM2852YMXAX-3.3/NOPB
HTSSOP
PWP
14
2500
367.0
367.0
35.0
Pack Materials-Page 3
MECHANICAL DATA
PWP0014A
MXA14A (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages