JDS COM200ET003Y-4.3 Wavereadytm communication and management module Datasheet

COMMUNICATIONS MODULES & SUBSYSTEMS
TM
WaveReady Communication and Management Module
COM-200
Key Features
• Supports both serial and Ethernet access to the module
• Provides craft (DB-9, RS232, or Ethernet/Telnet) access to a
TL1 command interface
• Provides Ethernet and RS232 access to TL1 and SNMP
management through the JDSU Node Manager software
• Offers compatibility with third-party SNMP-based
management tools such HP OpenView
Applications
• Enables monitoring and alarm
aggregation for all modules in a
node
• Enables software upgrades for
individual modules in a node
• Supports administration and
management for all modules in
three configurations: single shelf,
single network element (NE);
multiple shelves, single NE; multiple
shelves, multiple NEs
Compliance
• CC Part 15 (Class A); UL 60950 3rd
Edition, December 2000; CAN/CSAC22.2 No. 950-95; NEBS Level 3;
GR-63-CORE; GR-1089-CORE;
GR-78-CORE; CE; IEC 60950;
ETS300-386; EN 55022 (Class B);
73/23/EEC
• RoHS (exemptions 7b, 8a)
NORTH AMERICA : 800 498-JDSU (5378)
The WaveReady Communications Module 200 (COM-200) provides monitoring,
communication, and management of WaveReady modules when mounted in a
WaveReady 3000 series platform.
The COM-200 polls and reports shelf information, slot occupancy, and types and
status of modules installed in the shelf. The COM-200 is also used to set parameters of other modules and to upgrade the software version of modules in the
shelf.
The COM-200 supports serial and Ethernet connections. The serial interface
provides a direct connection for initial configuration of the COM-200 and local
management of other modules. The Ethernet interface provides for local or
remote management of the COM-200 and other modules in the shelf.
The Ethernet interface also allows COM-200 modules to be linked in series for
easy management of modules in multiple shelves. In addition, WaveReady transponders capable of providing a supervisory channel over the optical fiber will
allow the COM-200 to manage modules in a remote shelf.
The COM-200 supports two user interfaces: the WaveReady Node Manager,
which is a TL1/SNMP Windows-based graphical user interface, and a TL1 command interface.
Five light-emitting diodes (LEDs) on the front panel indicate the status of the
COM-200 module and other modules in the same shelf. LEDs associated with
the Ethernet ports indicate link activity.
WORLDWIDE : +800 5378-JDSU
www.jdsu.com/waveready
COMMUNICATIONS MODULE 200
2
Performance Specifications1
Parameter
Electrical Characteristics
DC supply voltage2
Power dissipation
Physical Dimensions
Size (H x W x L)
Weight (approximate)
Mounting options
Environmental Characteristics
Operating ambient temperature
Storage temperature
Relative humidity (non-condensing)
Interface
DB-9/RS232
RJ45 or 10/100BaseT Ethernet
Front panel
Alarm relay signals
Backplane Connector
Electrical
Software and Management
TL1 command mode
WaveReady Node Manager
1
2
Minimum
—
Typical
–48 V through WaveReady 3000-Series shelf
5W
Maximum
8.5 W
17.27 x 2.54 x 21.84 cm (6.8 x 1.0 x 8.6 in)
0.54 kg (1.2 lb)
Mounts in a WaveReady 3000-Series shelf in a standard 19- or 23-inch telecommunications rack
–5°C
–40°C
5%
—
—
—
55°C
85°C
95%
Craft interface. 3-wire serial TTL, 9600 Baud, no parity, no flow control, 8 data bits, 1 stop bit craft interface.
Two auto-sense, auto-crossover Ethernet ports (ports A and B) for networking and daisy-chaining. One local craft access (LCA)
Ethernet port for local management and provisioning.
5 LEDs: CARD (power), CRIT (Critical Alarm), MAJ (Major Alarm), MIN (Minor Alarm), ACO (Alarm Cut-Off).
2 pushbuttons: ACO (Alarm Cut-Off)and INIT (Initialize)
4 ports:RS232 (DB-9/RS232),LCA (RJ45 Ethernet,local craft access) A and B (RJ45 Ethernet,network ports)
Dry contact, critical, major, and minor alarms. Relay is open under normal operation. Relay is closed when power is off or an alarm is
active.
A single 96-pin connector mounted on the backplane. Compatible with all WaveReady 3000-Series shelves.
Standard TL1 syntax,Telcordia® GR-811-CORE compliant. Supported through the RS232 craft interface or Ethernet on ports LCA or A.
Windows graphical user interface,TL1, and SNMPv3 supported through the RS232 craft interface or Ethernet on ports LCA or A.
Compatible with third-party management software, such as HP OpenView. Communication with remote modules through an
embedded supervisory channel is available for some modules.Requires JDSU WaveReady system software release 3.0 or above.
Deploy product in accordance with each company's deployment directives.
The DC power supply must be –48 V SELV output and certified by a nationally recognized test laboratory (NRTL). UL tested at –48 V.
COMMUNICATIONS MODULE 200
3
Ordering Information
For more information on this or other products and their availability,please contact your local JDSU account manager or JDSU directly at
1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at [email protected].
Product Code
COM200ET003Y
COM200ET003Y-4.3
COM200ET003Y-4.4
COM200ET003Y-4.5
Telcordia is a registered trademark of Telcordia Technologies Incorporated.
Description
Communication Module 200 (COM-200)
Communication Module 200 (COM-200) with WaveReady System Release 4.3
Communication Module 200 (COM-200) with WaveReady System Release 4.4
Communication Module 200 (COM-200) with WaveReady System Release 4.5
COMMUNICATIONS MODULE 200
NORTH AMERICA : 800 498-JDSU (5378)
WORLDWIDE : +800 5378-JDSU
Product specifications and descriptions in this document subject to change without notice. © 2008 JDS Uniphase Corporation
WEBSITE : www.jdsu.com/waveready
10143108 003 0109 COMMODULE200.DS.CMS.TM.AE
January 2009
Similar pages