Infineon BTS707 Smart two channel highside power switch Datasheet

PROFET® BTS 707
Smart Two Channel Highside Power Switch
Product Summary
Overvoltage Protection
Vbb(AZ)
• Overload protection
• Current limitation
Vbb(on)
Operating voltage
• Short-circuit protection
active channels:
one
• Thermal shutdown
On-state resistance
RON
250
• Overvoltage protection
1.9
• Fast demagnetization of inductive loads Nominal load current IL(NOM)
Features
65
5.8 ... 58
two parallel
125
2.8
V
V
mΩ
A
• Reverse battery protection1)
• Open drain diagnostic output
• Open load detection in OFF-state
• CMOS compatible input
• Loss of ground and loss of Vbb protection
• Electrostatic discharge (ESD) protection
Application
• µC compatible power switch with diagnostic feedback
for 12 V and 24 V DC grounded loads
• Most suitable for inductive loads
• Replaces electromechanical relays, fuses and discrete circuits
General Description
N channel vertical power FET with charge pump, ground referenced CMOS compatible input and diagnostic

feedback, monolithically integrated in Smart SIPMOS technology.
Providing embedded protective functions.
Pin Definitions and Functions
Pin
1,10,
11,12,
15,16,
19,20
3
7
17,18
13,14
4
8
2
6
5,9
1)
Symbol Function
Vbb
Positive power supply voltage. Design the
wiring for the simultaneous max. short circuit
currents from channel 1 to 2 and also for low
thermal resistance
IN1
Input 1,2, activates channel 1,2 in case of
IN2
logic high signal
OUT1
Output 1,2, protected high-side power output
OUT2
of channel 1,2. Design the wiring for the max.
short circuit current
ST1
Diagnostic feedback 1,2 of channel 1,2,
ST2
open drain, low in on state on failure or high in
off state on failure
GND1
Ground 1 of chip 1 (channel 1)
GND2
Ground 2 of chip 2 (channel 2)
N.C.
Not Connected
Pin configuration (top view)
Vbb
GND1
IN1
ST1
N.C.
GND2
IN2
ST2
N.C.
Vbb
1
2
3
4
5
6
7
8
9
10
•
20
19
18
17
16
15
14
13
12
11
Vbb
Vbb
OUT1
OUT1
Vbb
Vbb
OUT2
OUT2
Vbb
Vbb
With external current limit (e.g. resistor RGND=150 Ω) in GND connection, resistor in series with ST
connection, reverse load current limited by connected load.
Semiconductor Group
1 of 12
2003-Oct-01
BTS 707
Block diagram
Voltage
source
Overvoltage
Current
protection
limit
+ Vbb
Leadframe
OUT1
17,18
Gate
protection
VLogic
3
IN1
4
ST1
1
GND1
Voltage
Charge pump
sensor
Level shifter
Limit for
unclamped
ind. loads
Rectifier
Temperature
sensor
Load
Open load
ESD
Logic
detection
Short circuit
detection
Chip 1
SignalGND
Chip 1
Load GND
Logic and protection circuit of chip 2
7
+ Vbb
Leadframe
OUT2
13,14
(equivalent to chip 1)
IN2
Load
8
ST2
6
GND2
SignalGND
Chip 2
Chip 2
PROFET
Load GND
Leadframe connected to pin 1, 10, 11, 12, 15, 16, 19, 20
Maximum Ratings at Tj = 25°C unless otherwise specified
Parameter
Symbol
Supply voltage (overvoltage protection see page 4)
Supply voltage for full short circuit protection
Tj,start = -40 ...+150°C
Load current (Short-circuit current, see page 5)
Operating temperature range
Storage temperature range
Vbb
Vbb
65
40
V
V
IL
Tj
Tstg
self-limited
-40 ...+150
-55 ...+150
A
°C
Semiconductor Group
2
Values
Unit
2003-Oct-01
BTS 707
Maximum Ratings at Tj = 25°C unless otherwise specified
Parameter
Symbol
Values
Power dissipation (DC)2)
Ta = 25°C:
(all channels active)
Ta = 85°C:
Electrostatic discharge capability (ESD)
IN, ST:
(Human Body Model)
all other pins:
Input voltage (DC)
Current through input pin (DC)
Current through status pin (DC)
Ptot
3
1.6
1.0
1.0
-0.5 ... +36
±2.0
±5.0
VESD
VIN
IIN
IST
Unit
W
kV
V
mA
see internal circuit diagram page 7
Thermal Characteristics
Parameter and Conditions
Symbol
min
Thermal resistance
junction - soldering point2),3)
each channel: Rthjs
2)
junction - ambient
one channel active: Rthja
all channels active:
Values
typ
max
Unit
18
---
K/W
Values
min
typ
max
Unit
----
-45
37
Electrical Characteristics
Parameter and Conditions, each of the two channels
Symbol
at Tj = 25 °C, Vbb = 12 V unless otherwise specified
Load Switching Capabilities and Characteristics
On-state resistance (Vbb to OUT)
each channel,
Tj = 25°C: RON
IL = 2 A
Vbb = 24 V
Tj = 150°C:
two parallel channels, Tj = 25°C:
Nominal load current
one channel active: IL(NOM)
two parallel channels active:
2)
Device on PCB , Ta = 85°C, Tj ≤ 150°C
Output current while GND disconnected or pulled
IL(GNDhigh)
up; Vbb = 32 V, VIN = 0, see diagram page 8
2)
3)
--
mΩ
225
400
250
500
1.60
2.4
113
1.9
2.8
125
--
A
--
--
1.1
mA
Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70µm thick) copper area for Vbb
connection. PCB is vertical without blown air. See page 12
Soldering point: upper side of solder edge of device pin 15. See page 12
Semiconductor Group
3
2003-Oct-01
BTS 707
Parameter and Conditions, each of the two channels
Symbol
at Tj = 25 °C, Vbb = 12 V unless otherwise specified
Turn-on time
to 90% VOUT:
Turn-off time
to 10% VOUT:
RL = 12 Ω, Vbb = 20 V, Tj =-40...+150°C
Slew rate on
10 to 30% VOUT, RL = 12 Ω, Vbb = 20 V,
Tj =-40...+150°C:
Slew rate off
70 to 40% VOUT, RL = 12 Ω, Vbb = 20 V,
Tj =-40...+150°C:
Operating Parameters
Operating voltage4)
Tj =-40...+150°C:
Undervoltage shutdown
Tj =-40...+150°C:
Undervoltage restart
Tj =-40...+150°C:
Undervoltage restart of charge pump
see diagram page 10
Tj =-40...+150°C:
Undervoltage hysteresis
∆Vbb(under) = Vbb(u rst) - Vbb(under)
Overvoltage protection5)
Tj =-40...+150°C:
I bb = 40 mA
Standby current, all channels off
VIN = 0
Tj =150°C:
6)
Operating current , VIN = 5V, Tj =-40...+150°C
one channel on:
IGND = IGND1 + IGND2,
two channels on:
Values
min
typ
max
Unit
15
20
---
80
70
µs
dV/dton
--
--
6
V/µs
-dV/dtoff
--
--
7
V/µs
Vbb(on)
Vbb(under)
Vbb(u rst)
Vbb(ucp)
5.8
2.7
---
---5.6
58
4.7
4.9
7.5
V
V
V
V
--
0.4
--
V
Vbb(AZ)
65
70
--
V
Ibb(off)
---
20
70
µA
IGND
---
2.2
4.4
---
mA
--19
-10
-4.0
--twice the current of one channel
VON(CL)
59
-75
A
ton
toff
∆Vbb(under)
Protection Functions7)
Initial peak short circuit current limit, (see timing
diagrams, page 9)
each channel, Tj =-40°C:
Tj =25°C:
Tj =+150°C:
two parallel channels
Output clamp (inductive load switch off)8)
at VON(CL) = Vbb - VOUT
Thermal overload trip temperature
Thermal hysteresis
4)
5)
6)
7)
8)
IL(SCp)
Tjt
∆Tjt
150
--
-10
---
V
°C
K
At supply voltage increase up to Vbb = 5.6 V typ without charge pump, VOUT ≈Vbb - 2 V
see also VON(CL) in circuit diagram on page 7.
Add IST, if IST > 0
Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are not
designed for continuous repetitive operation.
If channels are connected in parallel, output clamp is usually accomplished by the channel with the lowest
VON(CL)
Semiconductor Group
4
2003-Oct-01
BTS 707
Parameter and Conditions, each of the two channels
Symbol
at Tj = 25 °C, Vbb = 12 V unless otherwise specified
Reverse Battery
Reverse battery voltage 9)
Unit
--
--
32
V
-2.4
6
3
-4
µA
V
V
VON(SC)
--
2.5
--
RI
--
20
--
kΩ
VIN(T+)
VIN(T-)
∆ VIN(T)
VIN = 0.4 V: IIN(off)
VIN = 2.5 V: IIN(on)
td(ST OL3)
1
0.8
-1
10
--
--0.5
-25
200
2.5
--30
70
--
V
V
V
µA
µA
µs
Status output (open drain)
Zener limit voltage Tj =-40...+150°C, IST = +1.6 mA: VST(high)
ST low voltage
Tj =-40...+150°C, IST = +1.6 mA: VST(low)
5.4
--
6.1
--
-0.4
V
Diagnostic Characteristics
Open load detection current
Open load detection voltage
Short circuit detection voltage
(pin 3 to 5)
-Vbb
Values
min
typ
max
IL(off)
Tj =-40..+150°C: VOUT(OL)
Input and Status Feedback10)
Input resistance
(see circuit page 7)
Input turn-on threshold voltage
Input turn-off threshold voltage
Input threshold hysteresis
Off state input current
On state input current
Delay time for status with open load
(see timing diagrams, page 10)
9)
Requires a 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source
diode has to be limited by the connected load. Note that the power dissipation is higher compared to normal
operating conditions due to the voltage drop across the intrinsic drain-source diode. The temperature
protection is not active during reverse current operation! Input and Status currents have to be limited (see
max. ratings page 3 and circuit page 7).
10) If ground resistors R
GND are used, add the voltage drop across these resistors.
Semiconductor Group
5
2003-Oct-01
BTS 707
Truth Table
Channel 1
Channel 2
Normal
operation
Open load
Short circuit
to GND
Short circuit
to Vbb
Overtemperature
Undervoltage
Overvoltage
Input 1
Output 1
Status 1
Input 2
Output 2
Status 2
BTS 707
level
level
L
L
L
H
H
H
Z
L
H
H
H
H
L
L
L
H
L
L
L
H
H
H
H
H
L
L
L
H
L
L
L
L
L
H
L
L
no overvoltage shutdown,
see normal operation
Parallel switching of channel 1 and 2 is easily possible by connecting the inputs and outputs in parallel. The
status outputs ST1 and ST2 have to be configured as a 'Wired OR' function with a single pull-up resistor.
Terms
V
bb
Ibb
Leadframe
I IN1
3
I ST1
V
IN1 VST1
4
Vbb
IN1
ST1
I L1
PROFET
Chip 1
OUT1
R
GND1
IGND1
7
VON1
V
VOUT1
IN2
VST2
8
Vbb
IN2
I ST2
17,18
GND1
2
Leadframe
I IN2
ST2
I L2
PROFET
Chip 2
OUT2
VON2
13,14
GND2
6
R
GND2
IGND2
VOUT2
Leadframe (Vbb) is connected to pin 1,10,11,12,15,16,19,20
External RGND optional; two resistors RGND1, RGND2 = 150 Ω or a single resistor RGND = 75 Ω for reverse
battery protection up to the max. operating voltage.
Semiconductor Group
6
2003-Oct-01
BTS 707
Inductive and overvoltage output clamp,
Input circuit (ESD protection), IN1 or IN2
OUT1 or OUT2
R
IN
I
+Vbb
VZ
ESD-ZD I
I
I
V ON
GND
OUT
ESD zener diodes are not to be used as voltage clamp at
DC conditions. Operation in this mode may result in a drift of
the zener voltage (increase of up to 1 V).
PROFET
Power GND
Status output, ST1 or ST2
VON clamped to VON(CL) = -- V typ.
+5V
Overvoltage protection of logic part
GND1 or GND2
R ST(ON)
ST
+ V bb
GND
ESDZD
V
IN
ESD-Zener diode: 6.1 V typ., max 5.0 mA; RST(ON) < 0 Ω at
1.6 mA, ESD zener diodes are not to be used as voltage
clamp at DC conditions. Operation in this mode may result in
a drift of the zener voltage (increase of up to 1 V).
RI
Z2
Logic
R ST
ST
V
PROFET
Z1
GND
R GND
Short Circuit detection
Fault Signal at ST-Pin: VON > 2.5 V typ, no switch off by
the PROFET itself, external switch off recommended!
+ V bb
VZ1 = 6.1 V typ., VZ2 = 70 V typ., RI = 20 kΩ typ.,
RGND = 150 Ω, RST = 15 kΩ nominal.
Open-load detection, OUT1 or OUT2
V
ON
OFF-state diagnostic condition:
VOUT > 3 V typ.; IN low
OUT
Logic
unit
Signal GND
Short circuit
detection
OFF
I
Logic
unit
L(OL)
V
OUT
Open load
detection
Signal GND
Semiconductor Group
7
2003-Oct-01
BTS 707
Inductive load switch-off energy
dissipation
GND disconnect
E bb
E AS
Vbb
IN
PROFET
IN
OUT
PROFET
ST
=
GND
V
bb
V
IN
V
OUT
L
ST
GND
V
GND
ST
ELoad
Vbb
ZL
{
R
Any kind of load. In case of IN = high is VOUT ≈ VIN - VIN(T+).
Due to VGND > 0, no VST = low signal available.
EL
ER
L
Energy stored in load inductance:
2
EL = 1/2·L·I L
GND disconnect with GND pull up
While demagnetizing load inductance, the energy
dissipated in PROFET is
Vbb
IN
EAS= Ebb + EL - ER= VON(CL)·iL(t) dt,
PROFET
with an approximate solution for RL > 0 Ω:
OUT
ST
EAS=
GND
V
V
bb
V
IN ST
V
IL· L
(V + |VOUT(CL)|)
2·RL bb
ln (1+ |V
IL·RL
OUT(CL)|
)
GND
Any kind of load. If VGND > VIN - VIN(T+) device stays off
Due to VGND > 0, no VST = low signal available.
Vbb disconnect with energized inductive
load
high
Vbb
IN
PROFET
OUT
ST
GND
V
bb
For an inductive load current up to the limit defined by EAS
(max. ratings ) each switch is protected against loss of Vbb.
Consider at your PCB layout that in the case of Vbb disconnection with energized inductive load the whole load
current flows through the GND connection.
Semiconductor Group
8
2003-Oct-01
BTS 707
Timing diagrams
Both channels are symmetric and consequently the diagrams are valid for channel 1 and
channel 2
Figure 1a: Vbb turn on, :
Figure 3a: Short circuit:
shut down by overtempertature, reset by cooling
IN
IN
t d(bb IN)
V
bb
V OUT
normal
operation
V
Output short to GND
OUT
I
L
I
L(SCp)
A
I
L(SCr)
ST open drain
ST
A
t
t
in case of too early VIN=high the device may not turn on (curve A)
td(bb IN) approx. 150 µs
Heating up requires several milliseconds, depending on external
conditions. External shutdown in response to status fault signal
recommended.
Figure 2a: Switching an inductive load
Figure 4a: Overtemperature:
Reset if Tj <Tjt
IN
IN
ST
ST
V
OUT
V
OUT
I
L
T
J
t
t
Semiconductor Group
9
2003-Oct-01
BTS 707
Figure 5a: Open load, : detection in OFF-state, turn
on/off to open load
Figure 6a: Undervoltage:
IN
IN
V bb
t
d(ST OL3)
ST
V
bb(under)
Vbb(u cp)
V
bb(u rst)
V
OUT
I
V OUT
ST open drain
normal
open
L
*)
t
t
td(ST,OL3) depends on external circuitry because of high
impedance
*) IL = 6 µA typ
Figure 6b: Undervoltage restart of charge pump
V on
Figure 5b: Open load, : detection in OFF-state, open
load occurs in off-state
ST
on-state
off-state
IN
V
V
V
OUT
V
V
OUT(OL)
I
L
bb(u
normal
open
*)
bb(under)
Vbb
charge pump starts at Vbb(ucp) =5.6 V typ.
normal
*)
bb(u cp)
t
*) IL = 6 µA typ
Semiconductor Group
10
2003-Oct-01
BTS 707
Figure 7a: Overvoltage, no shutdown:
IN
Vbb
V
VON(CL)
OUT
VOUT(OL)
ST
t
Semiconductor Group
11
2003-Oct-01
BTS 707
Package and Ordering Code
Standard P-DSO-20-9
BTS 707
Ordering Code
Q67060-S7010-A2
Published by
Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81669 München
© Infineon Technologies AG 2001
All Rights Reserved.
Attention please!
The information herein is given to describe certain
components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not
limited to warranties of non-infringement, regarding circuits,
descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
All dimensions in millimetres
1) Does not include plastic or metal protrusions of 0.15 max per side
2) Does not include dambar protrusion of 0.05 max per side
For further information on technology, delivery terms and
conditions and prices please contact your nearest Infineon
Technologies Office in Germany or our Infineon
Technologies Representatives worldwide (see address list).
Definition of soldering point with temperature Ts:
upper side of solder edge of device pin 15.
Warnings
Due to technical requirements components may contain
dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies
Office.
Pin 15
Infineon Technologies Components may only be used in lifesupport devices or systems with the express written approval
of Infineon Technologies, if a failure of such components can
reasonably be expected to cause the failure of that lifesupport device or system, or to affect the safety or
effectiveness of that device or system. Life support devices
or systems are intended to be implanted in the human body,
or to support and/or maintain and sustain and/or protect
human life. If they fail, it is reasonable to assume that the
health of the user or other persons may be endangered.
Printed circuit board (FR4, 1.5mm thick, one layer
70µm, 6cm2 active heatsink area) as a reference for
max. power dissipation Ptot, nominal load current
IL(NOM) and thermal resistance Rthja
Semiconductor Group
12
2003-Oct-01
Similar pages