ETC ADS-926GM 14-bit, 500khz, low-power sampling a/d converter Datasheet

®
®
ADS-916
14-Bit, 500kHz, Low-Power
Sampling A/D Converters
FEATURES
•
•
•
•
•
•
•
•
14-bit resolution
500kHz sampling rate
Functionally complete; No missing codes
Edge-triggered; No pipeline delays
Small 24-pin DDIP or SMT package
Low power, 1.8 Watts maximum
Operates from ±15V or ±12V supplies
Unipolar 0 to +10V input range
GENERAL DESCRIPTION
INPUT/OUTPUT CONNECTIONS
The ADS-916 is a high-performance, 14-bit, 500kHz sampling
A/D converter. This device samples input signals up to Nyquist
frequencies with no missing codes. The ADS-916 features
outstanding dynamic performance including a THD of –90dB.
Housed in a small 24-pin DDIP or SMT (gull-wing) package,
the functionally complete ADS-916 contains a fast-settling
sample-hold amplifier, a subranging (two-pass) A/D converter,
a precise voltage reference, timing/control logic, and errorcorrection circuitry. Digital input and output levels are TTL.
Requiring ±15V (or ±12V) and +5V supplies, the ADS-916
dissipates 1.8W (1.6W for ±12V) maximum. The unit is offered
with a unipolar input (0 to +10V). Models are available for use
in either commercial (0 to +70°C) or military (–55 to +125°C)
operating temperature ranges. Applications include radar,
sonar, spectrum analysis, and graphic/medical imaging.
PIN
FUNCTION
PIN
1
2
3
4
5
6
7
8
9
10
11
12
BIT 14 (LSB)
BIT 13
BIT 12
BIT 11
BIT 10
BIT 9
BIT 8
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
24
23
22
21
20
19
18
17
16
15
14
13
FUNCTION
–12V/–15V SUPPLY
ANALOG GROUND
+12V/+15V SUPPLY
+10V REFERENCE OUT
ANALOG INPUT
ANALOG GROUND
BIT 1 (MSB)
BIT 2
START CONVERT
EOC
DIGITAL GROUND
+5V SUPPLY
DAC
18 BIT 1 (MSB)
17 BIT 2
+10V REF. OUT 21
REF
12 BIT 3
FLASH
ADC
S/H
ANALOG INPUT 20
S1
BUFFER
–
REGISTER
+
11 BIT 4
DIGITAL CORRECTION LOGIC
REGISTER
S2
10 BIT 5
9
BIT 6
8
BIT 7
7
BIT 8
6
BIT 9
5
BIT 10
4
BIT 11
3
BIT 12
2
BIT 13
1
BIT 14 (LSB)
START CONVERT 16
TIMING AND
CONTROL LOGIC
EOC 15
13
14
22
19, 23
24
+5V SUPPLY
DIGITAL GROUND
+12V/+15V SUPPLY
ANALOG GROUND
–12V/–15V SUPPLY
Figure 1. ADS-916 Functional Block Diagram
DATEL, Inc., 11 Cabot Boulevard, Mansfield, MA 02048-1151 (U.S.A.) • Tel: (508) 339-3000 Fax: (508) 339-6356 • For immediate assistance: (800) 233-2765
®
®
ADS-916
ABSOLUTE MAXIMUM RATINGS
PARAMETERS
+12V/+15V Supply (Pin 22)
–12V/–15V Supply (Pin 24)
+5V Supply (Pin 13)
Digital Input (Pin 16)
Analog Input (Pin 20)
Lead Temperature (10 seconds)
PHYSICAL/ENVIRONMENTAL
LIMITS
UNITS
0 to +16
0 to –16
0 to +6
–0.3 to +VDD +0.3
–4 to +17
+300
Volts
Volts
Volts
Volts
Volts
°C
PARAMETERS
Operating Temp. Range, Case
ADS-916MC, GC
ADS-916MM, GM
Thermal Impedance
θjc
θca
Storage Temperature
Package Type
Weight
MIN.
TYP.
MAX.
UNITS
0
–55
—
—
+70
+125
°C
°C
6
°C/Watt
24
°C/Watt
–65
—
+150
°C
24-pin, metal-sealed, ceramic DDIP or SMT
0.42 ounces (12 grams)
FUNCTIONAL SPECIFICATIONS
(TA = +25°C, ±VCC = ±15V (or ±12V), +VDD = +5V, 500kHz sampling rate, and a minimum 1 minute warmup ➀ unless otherwise specified.)
+25°C
ANALOG INPUT
Input Voltage Range ➁
Input Resistance
Input Capacitance
0 to +70°C
MIN.
TYP.
MAX.
—
—
—
0 to +10
1
7
—
—
15
+2.0
—
—
—
50
—
—
—
—
200
—
—
—
—
—
—
14
MIN.
–55 to +125°C
TYP.
MAX.
—
—
—
0 to +10
1
7
—
—
15
—
+0.8
+20
–20
—
+2.0
—
—
—
50
—
—
—
—
200
14
±0.5
±0.5
±0.05
±0.1
±0.1
—
—
—
±0.95
±0.1
±0.2
±0.25
—
—
—
—
—
—
—
14
—
—
–91
–84
–86
–79
—
—
–90
–82
77
75
MIN.
TYP.
MAX.
UNITS
—
—
—
0 to +10
1
7
—
—
15
Volts
kΩ
pF
—
+0.8
+20
–20
—
+2.0
—
—
—
50
—
—
—
—
200
—
+0.8
+20
–20
—
Volts
Volts
µA
µA
ns
14
±0.75
±0.5
±0.1
±0.1
±0.1
—
—
—
±0.95
±0.2
±0.2
±0.25
—
—
—
–0.95
—
—
—
14
14
±1.5
±0.75
±0.15
±0.15
±0.25
—
—
—
+1.25
±0.4
±0.4
±0.4
—
Bits
LSB
LSB
%FSR
%FSR
%
Bits
—
—
–91
–84
–86
–79
—
—
–90
–82
–82
–76
dB
dB
–85
–77
—
—
–90
–82
–85
–77
—
—
–87
–80
–81
–74
dB
dB
81
80
—
—
77
75
81
80
—
—
76
74
80
78
—
—
dB
dB
77
72
80
78
—
—
77
72
80
78
—
—
75
70
78
76
—
—
dB
dB
—
—
–86
310
—
—
—
—
–86
310
—
—
—
—
–86
360
—
—
dB
µVrms
—
—
—
—
—
—
7
3
84
±40
±20
5
—
—
—
—
—
—
—
—
—
—
—
—
7
3
84
±40
±20
5
—
—
—
—
—
—
—
—
—
—
—
—
7
3
84
±40
±20
5
—
—
—
—
—
—
MHz
MHz
dB
V/µs
ns
ps rms
1530
—
500
1570
1400
—
1610
2000
—
1530
—
500
1570
1400
—
1610
2000
—
1530
—
500
1570
1400
—
1610
2000
—
ns
ns
kHz
DIGITAL INPUT
Logic Levels
Logic "1"
Logic "0"
Logic Loading "1"
Logic Loading "0"
Start Convert Positive Pulse Width ➂
STATIC PERFORMANCE
Resolution
Integral Nonlinearity (fin = 10kHz)
Differential Nonlinearity (fin = 10kHz)
Full Scale Absolute Accuracy
Unipolar Offset Error (Tech Note 2)
Gain Error (Tech Note 2)
No Missing Codes (fin = 10kHz)
DYNAMIC PERFORMANCE
Peak Harmonics (–0.5dB)
dc to 100kHz
100kHz to 250kHz
Total Harmonic Distortion (–0.5dB)
dc to 100kHz
100kHz to 250kHz
Signal-to-Noise Ratio
(w/o distortion, –0.5dB)
dc to 100kHz
100kHz to 250kHz
Signal-to-Noise Ratio ➃
(& distortion, –0.5dB)
dc to 100kHz
100kHz to 250kHz
Two-Tone Intermodulation
Distortion (fin = 100kHz,
240kHz, fs = 500kHz –0.5dB)
Noise
Input Bandwidth (–3dB)
Small Signal (–20dB input)
Large Signal (–0.5dB input)
Feedthrough Rejection (fin = 250kHz)
Slew Rate
Aperture Delay Time
Aperture Uncertainty
S/H Acquisition Time
(to ±0.003%FSR, 10V step)
Overvoltage Recovery Time ➄
A/D Conversion Rate
2
®
®
ADS-916
+25°C
0 to +70°C
ANALOG OUTPUT
MIN.
TYP.
MAX.
Internal Reference
Voltage
Drift
External Current
+9.95
—
—
+10.0
±5
—
+10.05
—
1.5
+2.4
—
—
—
—
—
—
—
—
MIN.
–55 to +125°C
TYP.
MAX.
MIN.
TYP.
MAX.
UNITS
+9.95
—
—
+10.0
±5
—
+10.05
—
1.5
+9.95
—
—
+10.0
±5
—
+10.05
—
1.5
Volts
ppm/°C
mA
—
+0.4
–4
+4
+2.4
—
—
—
—
—
—
—
—
+0.4
–4
+4
+2.4
—
—
—
—
—
—
—
—
+0.4
–4
+4
Volts
Volts
mA
mA
—
35
—
—
Straight Binary
35
—
—
35
ns
+14.5
–14.5
+4.75
+15.0
–15.0
+5.0
+15.5
–15.5
+5.25
+14.5
–14.5
+4.75
+15.0
–15.0
+5.0
+15.5
–15.5
+5.25
+14.5
–14.5
+4.75
+15.0
–15.0
+5.0
+15.5
–15.5
+5.25
Volts
Volts
Volts
—
—
—
—
—
+50
–40
+70
1.6
—
+65
–50
+85
1.8
±0.01
—
—
—
—
—
+50
–40
+70
1.6
—
+65
–50
+85
1.8
±0.01
—
—
—
—
—
+50
–40
+70
1.6
—
+65
–50
+85
1.8
±0.01
mA
mA
mA
Watts
%FSR/%V
+11.5
–11.5
+4.75
+12.0
–12.0
+5.0
+12.5
–12.5
+5.25
+11.5
–11.5
+4.75
+12.0
–12.0
+5.0
+12.5
–12.5
+5.25
+11.5
–11.5
+4.75
+12.0
–12.0
+5.0
+12.5
–12.5
+5.25
Volts
Volts
Volts
—
—
—
—
—
+50
–40
+70
1.4
—
+65
–50
+80
1.6
±0.01
—
—
—
—
—
+50
–40
+70
1.4
—
+65
–50
+80
1.6
±0.01
—
—
—
—
—
+50
–40
+70
1.4
—
+65
–50
+80
1.6
±0.01
mA
mA
mA
Watts
%FSR/%V
DIGITAL OUTPUTS
Logic Levels
Logic "1"
Logic "0"
Logic Loading "1"
Logic Loading "0"
Delay, Falling Edge of EOC
to Output Data Valid
Output Coding
POWER REQUIREMENTS, ±15V
Power Supply Ranges
+15V Supply
–15V Supply
+5V Supply
Power Supply Currents
+15V Supply
–15V Supply
+5V Supply
Power Dissipation
Power Supply Rejection
POWER REQUIREMENTS, ±12V
Power Supply Ranges
+12V Supply
–12V Supply
+5V Supply
Power Supply Currents
+12V Supply
–12V Supply
+5V Supply
Power Dissipation
Power Supply Rejection
Footnotes:
➀ All power supplies must be on before applying a start convert pulse. All supplies
and the clock (START CONVERT) must be present during warmup periods. The
device must be continuously converting during this time. There is a slight
degradation in performance when using ±12V supplies.
➃ Effective bits is equal to:
(SNR + Distortion) – 1.76 +
20 log
Full Scale Amplitude
Actual Input Amplitude
6.02
➁ See Ordering Information for availability of ±5V input range. Contact DATEL for
availability of other input voltage ranges.
➄ This is the time required before the A/D output data is valid after the analog input
is back within the specified range.
➂ A 500 kHz clock with a 200ns wide start convert pulse is used for all production
testing. Only the rising edge of the start convert pulse is required for the device
to operate (edge-triggered). See Timing Diagram for more details.
TECHNICAL NOTES
initial offset and gain errors can be reduced to zero using
the input circuit of Figure 2. When using this circuit, or any
similar offset and gain-calibration hardware, make adjustments following warmup. To avoid interaction, always adjust
offset before gain.
1. Obtaining fully specified performance from the ADS-916
requires careful attention to pc-card layout and power
supply decoupling. The device's analog and digital ground
systems are connected to each other internally. For optimal
performance, tie all ground pins (14, 19 and 23) directly to a
large analog ground plane beneath the package.
3. When operating the ADS-916 from ±12V supplies, do not
drive external circuitry with the REFERENCE OUTPUT. The
reference's accuracy and drift specifications may not be
met, and loading the circuit may cause accuracy errors
within the converter.
Bypass all power supplies and the REFERENCE OUTPUT
(pin 21) to ground with 4.7µF tantalum capacitors in parallel
with 0.1µF ceramic capacitors. Locate the bypass capacitors as close to the unit as possible. If the user-installed
offset and gain adjusting circuit shown in Figure 2 is used,
also locate it as close to the ADS-916 as possible.
4. Applying a start convert pulse while a conversion is in
progress (EOC = logic "1") initiates a new and inaccurate
conversion cycle. Data for the interrupted and subsequent
conversions will be invalid.
2. The ADS-916 achieves its specified accuracies without the
need for external calibration. If required, the device's small
3
®
®
ADS-916
CALIBRATION PROCEDURE
Zero/Offset Adjust Procedure
(Refer to Figures 2 and 3)
1. Apply a train of pulses to the START CONVERT input
(pin 16) so the converter is continuously converting. If using
LED's on the outputs, a 200kHz conversion rate will reduce
flicker.
Any offset and/or gain calibration procedures should not be
implemented until devices are fully warmed up. To avoid
interaction, offset must be adjusted before gain. The ranges of
adjustment for the circuit of Figure 2 are guaranteed to
compensate for the ADS-916's initial accuracy errors and may
not be able to compensate for additional system errors.
2. Apply +305µV to the ANALOG INPUT (pin 20).
3. Adjust the offset potentiometer until the output bits are
all 0's and the LSB flickers between 0 and 1.
All fixed resistors in Figure 2 should be metal-film types, and
multiturn potentiometers should have TCR’s of 100ppm/°C or
less to minimize drift with temperature.
Gain Adjust Procedure
1. Apply +9.999085V to the ANALOG INPUT (pin 20).
A/D converters are calibrated by positioning their digital outputs
exactly on the transition point between two adjacent digital
output codes. This can be accomplished by connecting LED's
to the digital outputs and adjusting until certain LED's "flicker"
equally between on and off. Other approaches employ digital
comparators or microcontrollers to detect when the outputs
change from one code to the next.
2. Adjust the gain potentiometer until the output bits are all 1's
and the LSB flickers between 1 and 0.
Table 1. Zero and Gain Adjust
INPUT VOLTAGE
RANGE
For the ADS-916, offset adjusting is normally accomplished at
the point where the output bits are 0's and the LSB just
changes from a 0 to a 1. This digital output transition ideally
occurs when the applied analog input is +½LSB (+305µV).
0 to +10V
Gain adjusting is accomplished when all bits are 1's and the
LSB just changes from a 1 to a 0. This transition ideally occurs
when the analog input is at +full scale minus 1½ LSB's
(+9.999085V).
20kΩ
–15V
SIGNAL
INPUT
200kΩ
INPUT VOLTAGE
(0 to +10V)
+9.999390
+7.500000
+5.000000
+2.500000
+0.000610
0.000000
2kΩ
GAIN
ADJUST
+15V
1.98kΩ
To Pin 20
of ADS-916
50Ω
GAIN ADJUST
+FS –1½ LSB
+305µV
+9.999085V
Table 2. Output Coding
+15V
ZERO/
OFFSET
ADJUST
ZERO ADJUST
+½ LSB
UNIPOLAR
SCALE
+FS –1LSB
+3/4 FS
+1/2 FS
+1/4 FS
+1LSB
0
Figure 2. ADS-916 Calibration Circuit
18 BIT 1 (MSB)
+
4.7µF
13
17 BIT 2
12 BIT 3
14 DIGITAL
GROUND
11 BIT 4
10 BIT 5
9 BIT 6
0.1µF
ADS-916
24
–12V/–15V
4.7µF
+
4.7µF
8 BIT 7
7 BIT 8
0.1µF
19, 23
6 BIT 9
5 BIT 10
4 BIT 11
ANALOG
GROUND
0.1µF
+
22
+12V/+15V
3 BIT 12
2 BIT 13
ANALOG
20 INPUT
0 to +10V
1 BIT 14 (LSB)
15 EOC
21 +10V REF. OUT
0.1µF
11
11
10
01
00
00
Coding is straight binary; 1LSB = 610µV.
–15V
+5V
DIGITAL OUTPUT
MSB
LSB
+
START
16
CONVERT
4.7µF
Figure 3. Typical ADS-916 Connection Diagram
4
1111
0000
0000
0000
0000
0000
1111 1111
0000 0000
0000 0000
0000 0000
0000 0001
0000 0000
®
®
ADS-916
THERMAL REQUIREMENTS
Electrically-insulating, thermally-conductive "pads" may be
installed underneath the package. Devices should be soldered
to boards rather than "socketed", and of course, minimal air
flow over the surface can greatly help reduce the package
temperature.
All DATEL sampling A/D converters are fully characterized and
specified over operating temperature (case) ranges of
0 to +70°C and –55 to +125°C. All room-temperature
(TA = +25°C) production testing is performed without the use of
heat sinks or forced-air cooling. Thermal impedance figures for
each device are listed in their respective specification tables.
In more severe ambient conditions, the package/junction
temperature of a given device can be reduced dramatically
(typically 35%) by using one of DATEL's HS Series heat sinks.
See Ordering Information for the assigned part number. See
page 1-183 of the DATEL Data Acquisition Components
Catalog for more information on the HS Series. Request
DATEL Application Note AN-8, "Heat Sinks for DIP Data
Converters", or contact DATEL directly, for additional
information.
These devices do not normally require heat sinks, however,
standard precautionary design and layout procedures should
be used to ensure devices do not overheat. The ground and
power planes beneath the package, as well as all pcb signal
runs to and from the device, should be as heavy as possible to
help conduct heat away from the package.
N+1
N
START
CONVERT
200ns
typ.
10ns typ.
INTERNAL S/H
Acquisition Time
Hold
430ns typ.
1570ns ±40ns
70ns ±10ns
90ns typ.
EOC
Conversion Time
420ns ±20ns
35ns max.
74ns max.
OUTPUT
DATA
Data N Valid (1926ns min.)
Data (N – 1) Valid
Invalid
Data
Notes: 1. fs = 500kHz.
2. The ADS-916 is an edge-triggered device. All internal operations
are triggered by the rising edge of the start convert pulse, which
may be as narrow as 50nsec. All production testing is performed
at a 500kHz sampling rate with 200nsec wide start pulses. For
lower sampling rates, wider start pulses may be used, however, a
minimum pulse width low of 50nsec must be maintained.
Figure 4. ADS-916 Timing Diagram
5
+15V
5
7
9
6
8
10
SG1
26
25
24 23
22 21
20 19
18 17
16 15
14 13
12 11
1
3
2
4
P1
C19
2.2MF
ANALOG
INPUT
P4
-15V
20K
6
C21
0.1MF
+15V
-15V
+5V
SEE NOTE 1
START
CONVERT
C20
0.1MF
J5
7
U6
+
–
3
2
XTAL
Y1
8
14
J1
+15V
C11
2.2MF
P3
1
3
2
10K 0.1%
R7
C22
2.2
-15V MF
4
7
R6
2K 0.1%
0.1%
R4
1.98K
OP-77
50
GAIN
ADJ
R1
C1
0.1MF
R3
200K 5%
+
–
+5V
J2
C23
0.1MF
0.1%
R8
10K
C18
0.1MF
+
2.2MF
C24
2
1
-15V
C12
0.1MF
C10
0.1MF
6
AD845
C6
2.2MF
4
-15V
U5
7
C4
2.2MF
+15V
C5
0.1MF
C3
0.1MF
24
23
22
21
20
19
18
17
16
15
14
13
C8
2.2MF
11
5
4
74LS86
U4
ADS-916/917/919/929
12
+5V
B3
11
DGND
B4
10
EOC
B5
9
ST. CONV
B6
8
B2
B7
7
U1
B1
B8
6
AGND
B9
5
INPUT
B10
4
+10VREF
B11
3
+15V
B12
2
AGND
B13
1
-15V
B14
C7
0.1MF
74LS86
U4
1. SG1 SHOULD BE OPEN. SG2 &
SG3 SHOULD BE CLOSED.
2. FOR ADS-916 Y1 IS 500 KHZ.
FOR ADS-917 Y1 IS 1 MHZ.
FOR ADS-919/929 Y1 IS 2 MHZ.
74LS86
3
NOTES:
C14
2.2MF
+5V
13
12
6
Figure 5. ADS-916 Evaluation Board Schematic
7
U4
14
+5V
C13
0.1MF
C15
0.1MF
C9
2.2MF
R5
2K .1%
+
R2
+
OFFSET
ADJ
+
+
C2
15pF COG
+
+
6
+
+
+15V
10
9
2G
19
17
15
13
11
8
6
4
2
10
8
1G
2Y4
2Y3
2Y2
2Y1
1Y4
1Y3
1Y2
1Y1
20
74LS86
U4
2G
2A4
2A3
2A2
2A1
1A4
1A3
1A2
1A1
74LS240
B5
B6
9
7
1
3
J4
8
B13
1
3
5
7
17
9
7
11
13
15
LSB 5
P2
19
21
23
25
27
ST.CONV. 1
J3
34 ENABLE
2
4 EOC 3
6
10
B12
B14
12
B11
14
16
18
20
22
24
26
B10
9
31
33
28 MSB 29
30
32
12
B9
B8
SG3
SG2
14
16
18
B7
B4
12
5
B3
B2
B1
14
16
18
C17
0.1MF
10
1G
2Y4
2Y3
2Y2
+5V
2A4
2A3
2A2
2Y1
1Y4
1A4
2A1
1Y3
1Y2
1Y1
20
C16
0.1MF
1A3
1A2
1A1
U3
19
17
15
13
11
8
6
4
2
74LS240
U2
+5V
®
®
ADS-916
®
®
ADS-916
0
–10
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
–140
–150
–160
–170
0
25
50
75
100
125
150
175
200
Frequency (kHz)
(fs = 500kHz, fin = 240kHz, Vin = –0.5dB, 16,384-point FFT)
Figure 6. ADS-916 FFT Analysis
+0.34
DNL (LSB's)
0
Number of Occurrences
Amplitude Relative to Full Scale (dB)
–20
–0.33
0
0
Digital Output Code
Digital Output Code
16,384
16,384
Figure 7. ADS-916 Histogram and Differential Nonlinearity
7
225
250
®
®
ADS-916
MECHANICAL DIMENSIONS INCHES (mm)
1.31 MAX.
(33.27)
24-Pin DDIP
Versions
24
ADS-916MC
ADS-916MM
ADS-926MC
ADS-926MM
ADS-926/883
Dimension Tolerances (unless otherwise indicated):
2 place decimal (.XX) ±0.010 (±0.254)
3 place decimal (.XXX) ±0.005 (±0.127)
13
Lead Material: Kovar alloy
0.80 MAX.
(20.32)
1
Lead Finish: 50 microinches (minimum) gold plating
over 100 microinches (nominal) nickel plating
12
0.100 TYP.
(2.540)
1.100
(27.940)
0.235 MAX.
(5.969)
PIN 1 INDEX
0.200 MAX.
(5.080)
0.010
(0.254)
0.190 MAX.
(4.826)
0.100
(2.540)
0.600 ±0.010
(15.240)
SEATING
PLANE
0.025
(0.635)
0.040
(1.016)
0.018 ±0.002
(0.457)
+0.002
–0.001
0.100
(2.540)
1.31 MAX.
(33.02)
24-Pin
Surface Mount
Versions
ADS-916GC
ADS-916GM
ADS-926GC
ADS-926GM
Dimension Tolerances (unless otherwise indicated):
2 place decimal (.XX) ±0.010 (±0.254)
3 place decimal (.XXX) ±0.005 (±0.127)
13
24
Lead Material: Kovar alloy
0.80 MAX.
(20.32)
1
0.190 MAX.
(4.826)
Lead Finish: 50 microinches (minimum) gold plating
over 100 microinches (nominal) nickel plating
12
0.020 TYP.
(0.508)
0.060 TYP.
(1.524)
0.130 TYP.
(3.302)
PIN 1
INDEX
0.100
(2.540)
0.100 TYP.
(2.540)
0.020
(0.508)
0.015
(0.381)
MAX. radius
for any pin
0.010 TYP.
(0.254)
0.040
(1.016)
ORDERING INFORMATION
MODEL
NUMBER
ADS-916MC
ADS-916MM
ADS-916GC
ADS-916GM
ADS-926MC
ADS-926MM
ADS-926GC
ADS-926GM
ADS-926/883
®
OPERATING
TEMP. RANGE
0 to +70°C
–55 to +125°C
0 to +70°C
–55 to +125°C
0 to +70°C
–55 to +125°C
0 to +70°C
–55 to +125°C
–55 to +125°C
ANALOG
INPUT
Unipolar (0 to +10V)
Unipolar (0 to +10V)
Unipolar (0 to +10V)
Unipolar (0 to +10V)
Bipolar (±5V)*
Bipolar (±5V)*
Bipolar (±5V)*
Bipolar (±5V)*
Bipolar (±5V)*
®
ADS-B916/917
Evaluation Board (without ADS-916)
HS-24
Heat Sinks for all ADS-916/926 DDIP models
Receptacles for PC board mounting can be ordered through
AMP Inc. Part #3-331272-8 (Component Lead Socket), 24 required.
For MIL-STD-883 product specifications, contact DATEL.
* For information, see ADS-926 data sheet.
ISO 9001
R
DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151
Tel: (508) 339-3000 (800) 233-2765
Fax: (508) 339-6356 Email: [email protected]
Data sheet fax back: (508) 261-2857
ACCESSORIES
E
G
I
S
T
E
R
E
D
DS-0300A
11/96
DATEL (UK) LTD. Tadley, England Tel: (01256)-880444
DATEL S.A.R.L. Montigny Le Bretonneux, France Tel: 01-34-60-01-01
DATEL GmbH Munchen, Germany Tel: 89-544334-0
DATEL KK Tokyo, Japan Tel: 3-3779-1031, Osaka Tel: 6-354-2025
DATEL makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein
do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. The DATEL logo is a registered DATEL, Inc. trademark.
Similar pages