TSC HERF1005G Isolated 10.0 amps. glass passivated high efficient rectifier Datasheet

HERF1001G - HERF1008G
Isolated 10.0 AMPS. Glass Passivated High Efficient Rectifiers
ITO-220AB
Features
Glass passivated chip junction.
High efficiency, Low VF
High current capability
High reliability
High surge current capability
For use in low voltage, high frequency inventor, free
wheeling, and polarity protection application.
Mechanical Data
Case: ITO-220AB molded plastic
Epoxy: UL 94V0 rate flame retardant
Terminals: Pure tin plated, lead free solderable per
MIL-STD-202, Method 208 guaranteed
Polarity: As marked
High temperature soldering guaranteed:
o
260 C/ 0.25” (6.35mm) from case for 10
seconds.
Mounting torque: 5 in – 1bs. max.
Weight: 2.24 grams
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25 oC ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified
Current @T C = 100 oC
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
Maximum Instantaneous Forward Voltage
@ 5.0A
Maximum DC Reverse Current
@T A=25 oC at Rated DC Blocking Voltage
@ T A=125 oC
Symbol HERF HERF HERF HERF HERF HERF HERF HERF Units
1001G 1002G 1003G 1004G 1005G 1006G 1007G 1008G
V RRM
V RMS
V DC
200
140
200
300
210
300
400
280
400
600
420
600
800 1000
560 700
800 1000
V
V
V
10
A
IFSM
125
A
VF
1.0
1.3
Trr
Cj
R θJC
TJ
1.7
10
400
IR
Typical Junction Capacitance ( Note 2 )
Operating Temperature Range
100
70
100
I(AV)
Maximum Reverse Recovery Time ( Note 1 )
Typical Thermal Resistance (Note 3)
50
35
50
50
60
80
40
3.0
-65 to +150
-65 to +150
Storage Temperature Range
T STG
1. Reverse Recovery Test Conditions: IF=0.5A, IR =1.0A, IRR =0.25A
Notes:
2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C.
3. Mounted on Heatsink Size of 2 in x 3 in x 0.25 in Al-Plate.
V
uA
uA
nS
pF
o
C/W
o
C
o
C
Version: A06
RATINGS AND CHARACTERISTIC CURVES (HERF1001G THRU HERF1008G)
FIG.2- TYPICAL REVERSE CHARACTERISTICS
1000
8
INSTANTANEOUS REVERSE CURRENT. ( A)
6
4
2
0
0
100
50
150
o
FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE
CURRENT
150
125
0
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
100
50
1
2
5
10
20
50
100
NUMBER OF CYCLES AT 60Hz
FIG.4- TYPICAL JUNCTION CAPACITANCE
240
200
CAPACITANCE.(pF)
Tj=25 0C
1
FIG.5- TYPICAL FORWARD CHARACTERISTICS
75
25
Tj=75 0C
0.1
100
Tj=125 0C
10
8.3ms Single Half Sine Wave
JEDEC Method
INSTANTANEOUS FORWARD CURRENT. (A)
PEAK FORWARD SURGE CURRENT. (A)
LEAD TEMPERATURE. ( C)
100
160
120
HE
RF
100
1G
80
40
HER
~H
ER
06G
~HE
RF1
2
5
30
10
F
ER
10
20
50
100
200
500
05
G
H
1
0.3
0.1
0
Tj=25 C
PULSE WIDTH-300 S
1% DUTY CYCLE
0.01
0.4
G
10
G
08
10
RF
E
H
G~
06
10
F
R
HE
3
0.03
008
0
1
F10
05G
F10
HE
RF
10
01
G
~H
ER
F1
00
4G
AVERAGE FORWARD CURRENT. (A)
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
10
0.6
0.8
1.0
1.2
1.4
1.6
1.8
FORWARD VOLTAGE. (V)
1000
REVERSE VOLTAGE. (V)
FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50
NONINDUCTIVE
10
NONINDUCTIVE
trr
+0.5A
(+)
50Vdc
(approx)
(-)
(-)
DUT
PULSE
GENERATOR
(NOTE 2)
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
0
-0.25A
(+)
-1.0A
1cm
SET TIME BASE FOR
5/ 10ns/ cm
Version: A06
Similar pages