EMC EM84530 2-in-one mouse controller Datasheet

EM84530
2-IN-ONE MOUSE CONTROLLER
ary
n
i
m
i
l
e
Pr
GENERAL DESCRIPTION
The EM84530 Mouse Controller is specially designed to control serial mouse or PS/2 mouse device.
This single chip can interface three key-switches and 4 X-Y photo-couples directly to RS-232C or 8042
controller.
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Include PnP software scrolling function
Using 50kΩ ±1% resistor for RC oscillation.
Compatible with legacy PS/2 mouse.
Compatible with Microsoft serial mouse.
Compatible with Microsoft PS/2 mouse.
Serial or PS/2 port auto-detect.
100 bytes PnP ID code could be filled by code layer.
Built-in noise immunity circuit.
The sampiling rate of motion detector is up to 65KHz.
Built-in three zener diodes : one in VDD to VSS, two in RTS to VDD.
CMOS push-pull RXD output.
Built-in current comparator for photo-couples input.
Built-in three step dynamic input impedance.
Three key-switches and four photo-couples inputs.
RTS debouncing circuit included.
Photo couple test mode included.
Low power dissipation.
APPLICATION
• Serial PnP mouse.
• PS/2 mouse.
• Combo mouse.
PIN ASSIGNMENT
EM84530
VDD
OSC.OUT
NC
NC
CLK/RTS
DATA/RXD
OPT
VSS
1
2
3
4
5
6
7
8
* This specification are subject to be changed without notice.
16
15
14
13
12
11
10
9
OSCR
Y2
Y1
X2
X1
L
M
R
6.28.1999
1
EM84530
2-IN-ONE MOUSE CONTROLLER
inary
m
i
l
e
r
P
FUNCTIONAL BLOCK DIAGRAM
DATA/RXD
CLK/RTS
C
O
M
P
A
R
A
T
O
R
OPT
X1
X2
Y1
Y2
D
ME
OT
TE
IC
OT
NO
R
COUNTER
MULTIPLEXER
D
E
B
O
U
N
C
E
L
M
R
DATA
I/O
TIMING
CONTROLLER
COMMAND
& STATUS
OR PNP IO
SYSTEM CLOCK
GENERATOR
OSCR
OSC.OUT
RC
OSCILLATION
PIN DESCRIPTIONS
Symbol
I/O
OPT
I/O
OSC.OUT
O
OSCR
CLK/RTS
I
I/O
DATA/RXD
I/O
R
M
L
X1
X2
Y1
Y2
VSS
VDD
I
I/O
I/O
I
I
I
I
Function
INPUT: 200kΩ pull low to VSS.
When OPT is connected to VDD, EM84530 will enter test mode. In test mode,
L will be the output of X1,while M will be the output of X2. Toggling R key can
change these output to be Y1,Y2 respectively.
The RC oscillation clock output. Or 3mA sink current output for X, Y photo
emitters.
Connect 50kΩ±1% precise resistor for oscillation.
Connect directly to 8042 auxiliary port CLK line in PS/2 mode or connect directly
to RS-232C RTS pin in serial mode. Auto-detect the operating port by this pin.
Connect directly to 8042 auxiliary port DATA line in PS/2 mode or connect
directly to RS-232C RXD pin in serial mode.
Three key-switches inputs. 200kΩ resistor pull low.
Three step dynamic input impedance. If OSC.OUT is not connected to LEDs, the
dynamic input impedance will be off.
Use current comparator to measure photo-couples "ON", or "OFF".
Negative power.
Power line.
* This specification are subject to be changed without notice.
6.28.1999
2
EM84530
2-IN-ONE MOUSE CONTROLLER
ary
n
i
m
i
l
e
Pr
FUNCTION DESCRIPTIONS
(I) Serial Mouse :
In Microsoft mode, the transmission cycle consists of four bytes in one report. Each byte contains one start
bit, 7 data bits and two stop bits. The first byte contains "L", "R" key status and four bits of the two most
significant bits in horizontal counter and vertical counter. The second byte represents the value accumulated
by horizontal counter, the third byte is the data of the vertical counter. The last byte contains only "M" key
status. The vertical data is transmitted in 2's complement.
Output byte arrange
Bit no.
1st byte
2nd byte
3rd byte
4th byte
......
......
....
....
....
6
1
0
0
0
5
L
H5
V5'
0
4
R
H4
V4'
M
3
V7'
H3
V3'
0
2
V6'
H2
V2'
0
1
H7
H1
V1'
0
0
H6
H0
V0'
0
Plug & Play ID code
When RTS input from low to high, EM83810 will send a string ID code. Customer can specify the contains
of the code area and the total lenth below 100 bytes by changing the code layer.
Field Name
Other ID
Begin ID
PnP Revision
EISA ID
Product ID
Serial Number
Class ID
Driver ID
User Name
Length
<17
1
2
3
4
9
<34
<42
<42
Checks um
End PnP
2
1
Field Data
4D, 5A, 40, 00, 00, 00
08
01, 24
25, 2D, 23
10, 10, 10, 11
3C
3C, 2D, 2F, 35, 33, 25
3C, 30, 2E, 30, 10 26, 10, 21
3C, 25, 2D, 23, 00, 33, 23, 32,
2F, 2C, 2C, 29, 2E, 27, 00, 33,
25, 32, 29, 21, 2C, 00, 2D, 2F,
35, 33, 25
21, 15
09
Description
ID for legacy
Begin PnP ID
Version 1.00
EMC
0001
None provided
Mouse Class
PnP0F0A
EMC SCROLLING
SERIAL MOUSE
2 bytes checks um
End PnP ID
(II) Legacy PS/2 mouse operating:
(A) Operating mode
There are four operating modes in PS/2 mouse:
a. Reset Mode:
In this mode a self-test is initiated during power-on or by a Reset command. After reset signal, PS/2 mouse
will
(a) Send completion code AA & ID code 00.
(b) Set default :
* This specification are subject to be changed without notice.
6.28.1999
3
EM84530
2-IN-ONE MOUSE CONTROLLER
inary
m
i
l
e
r
P
sampling rate: 100 reports/s
non-autospeed
stream mode
2 dot/count
disable
b. Stream Mode:
The maximum rate of transfer is the programmed sample rate.
Data report is transmitted if
(a) switch is pressed
(b) movement has been detect
c. Remote Mode:
Data is transmitted only in response to a Read Data command.
d. Wrap Mode:
Any byte of data sent by the system, except hex EC ( Reset wrap mode ) or hex FF ( Reset ), is returned
by EM84530.
B). PS/2 Mouse Data Report:
a). In stream mode: A data report is sent at the end of a sample interval.
b). In remote mode: A data report is sent in response to Read Data command.
c). Data report format:
Byte
1
2
3
Bit
0
1
2
3
4
5
6
7
0-7
0-7
Description
Left button status; 1 = pressed
Right button status; 1 = pressed
Middle button status; 1 = pressed
Reserve
X data sign; 1 = negative
Y data sign; 1 = negative
X data overflow; 1 = overflow
Y data overflow; 1 = overflow
X data ( D0 - D7 )
Y data ( D0 - D7 )
C) PS/2 mouse Data Transmission:
a). EM84530 generates the clocking signal when sending data to and receiving data from the system.
b). The system requests EM84530 receive system data output by forcing the DATA line to an inactive level
and allowing CLK line to go to an active level.
* This specification are subject to be changed without notice.
6.28.1999
4
EM84530
2-IN-ONE MOUSE CONTROLLER
ary
n
i
m
i
l
e
Pr
c). Data transmission frame:
Bit
1
2-9
10
11
Function
Start bit ( always 0 )
Data bits ( D0 - D7 )
Parity bit ( odd parity )
Stop bit ( always 1 )
d). Data Output ( data from EM84530 to system ):
If CLK is low ( inhibit status ) , data is no transmission.
If CLK is high and DATA is low ( request-to-send ), data is updated. Data is received from the system
and no transmission are started by EM84530 until CLK and DATA both high. If CLK and DATA both
are high, the transmission is ready. DATA is valid prior to the falling edge of CLK and beyond the rising edge
of CLK. During transmission, EM84530 check for line contention by checking for an inactive level on CLK
at intervals not to exceed 100u sec. Contention occurs when the system lowers CLK to inhibit EM84530
output after EM84530 has started a transmission. If this occurs before the rising edge of the tenth clock,
EM84530 internal store its data in its buffer and returns DATA and CLK to an active level. If the contention
does not occur by the tenth clock, the transmission is complete.
Following a transmission, the system inhibits EM84530 by holding CLK low until it can service the input
or until the system receives a request to send a response from EM84530.
e). Data Input ( from system to EM84530 ):
The system first check if EM84530 is transmitting data. If EM84530 is transmitting, the system can override
the output forcing CLK to an inactive level prior to the tenth clock. If EM84530 transmission is beyond
the tenth clock, the system receives the data. If EM84530 is not transmitting or if the system choose to
override the output, the system force CLK to an inactive level for a period of not less than 100µ sec while
preparing for output. When the system is ready to output start bit (0), it allows CLK go to active level. If
request-to-send is detected, EM84530 clocks 11 bits. Following the tenth clock EM84530 checks for
an active level on the DATA line, and if found, force DATA low , and clock once more. If occurs framing
error, EM84530 continue to clock until DATA is high, then clocks the line control bit and request a
Resend. When the system sends out a command or data transmission that requires a response, the system
waits for EM84530 to response before sending its next output.
D). PS/2 Mouse Error Handling:
a). A Resend command ( FE ) following receipt of an invalid input or any input with incorrect parity.
b). If two invalid input are received in succession, an error code of hex (FC) is send to the system.
c). The counter accumulators are cleared after receiving any command except “Resend”.
d). EM84530 receives a Resend command ( FE ), it transmit its last packet of data.
e). In the stream mode “Resend” is received by EM84530 following a 3-byte data packet transmission
to the system. EM84530 resend the 3-byte data packet prior to clearing the counter.
* This specification are subject to be changed without notice.
6.28.1999
5
EM84530
2-IN-ONE MOUSE CONTROLLER
f). A response is sent within 25 ms if
inary
m
i
l
e
r
P
a). The system requires a response
b). An error is detected in the transmission
g). If EM84530 is in the stream mode :
a). The system disables EM84530 before issuing any command requiring a response.
b). When a command requiring a response is issued by the system ,another command should not be issue
until either the response is received or 25ms has passed.
E). PS/2 Mouse Commands Description:
There are 16 valid commands that transmits between the system and EM84530. The “FA” code is always the
first response to any valid input received from the system other than a Set Wrap Mode or Resend command.
The following table list the commands:
Hex Code
FF
FE
F6
F5
F4
F3,XX
F2
F0
EE
EC
EB
EA
E9
E8,XX
E7
E6
Command
Reset
Resend
Set Default
Disable
Enable
Set Sampling Rate
Read Device Type
Set Remote Mode
Set Wrap Mode
Reset Wrap Mode
Read Data
Set Stream Mode
Status Request
Set Resolution
Set Auto-speed
Reset Auto-speed
Echo code
FA,AA,00
XX,(XX,XX)
FA
FA
FA
FA,FA
FA,00
FA
FA
FA
FA,XX,XX,XX
FA
FA,XX,XX,XX
FA,FA
FA
FA
The following describes valid commands:
a). Reset ( FF )
EM84530 operation:
a). Completion the reset.
b). Transmitted FA, AA, 00 to the system.
c). Set default:
sampling rate: 100 reports/s
non-autospeed
stream mode
2 dots/count
disable
* This specification are subject to be changed without notice.
6.28.1999
6
EM84530
2-IN-ONE MOUSE CONTROLLER
ary
n
i
m
i
l
e
Pr
b). Resend ( FE )
a). Any time EM84530 receives an invalid command, it returns a Resend command to the system.
b). When EM84530 receives a Resend command, it retransmits its last packet of data. If the last packet was
a Resend command, it transmits the packet just prior to the Resend command.
c). In stream mode, if a Resend command is received by EM84530 immediately following a 3-byte data
packet transmission to the system.
c). Set Default ( F6 )
The command reinitializes all conditions to the power-on defaults.
d). Disable ( F5 )
This command is used in the stream mode to stop transmissions from EM84530.
e). Enable ( F4 )
Begins transmissions, if in stream mode.
f). Set Sampling Rate ( F3,XX )
In the stream mode, this command sets the sampling rate to the value indicated by byte hex XX,
shown in following:
Second byte XX
0A
14
28
3C
50
64
C8
Sample Rate
10/sec
20/sec
40/sec
60/sec
80/sec
100/sec
200/sec
g). Read Device Type ( F2 )
EM84530 always echoes “ FA,00 “ following this command.
h). Set Remote Mode ( F0 )
Data value are reported only in response to a Read Data command.
i). Set Wrap Mode ( EE )
Wrap mode remains until Reset ( FF ) or Reset Wrap Mode ( EC ) is received.
j). Reset Wrap Mode ( EC )
EM84530 returns to the previous mode of operation after receiving this command.
k). Read Data ( EB )
This command is executed in either remote or stream mode. The data is transmitted even if there has been
no movement since the last report or the button status is unchanged. Following a Read Data command,
the registers are cleared after a data transmission.
l). Set Stream Mode ( EA )
This command sets EM84530 in stream mode.
* This specification are subject to be changed without notice.
6.28.1999
7
EM84530
2-IN-ONE MOUSE CONTROLLER
inary
m
i
l
e
r
P
m). Status Request ( E9 )
When this command is issued by the system, EM84530 respond with a 3-byte status report as follows:
Byte
1
Bit
0
1
2
3
4
5
6
7
0-7
0-7
2
3
Description
1 = Right button pressed
1 = Middle button pressed
1 = Left button pressed
Reserved
0 = Normal speed, 1 = Autospeed
0 = Disabled, 1 = Enabled
0 = Stream mode, 1 = Remote mode
Reserved
Current resolution setting ( D0 - D7 )
Current sampling rate ( D0 - D7 )
n). Set Resolution ( E8,XX )
EM84530 provides four resolutions selected by the second byte of this command as follows:
Second Byte XX
00
01
02
03
Resolution
8 dots/count
4 dots/count
2 dots/count
1 dots/count
o). Set Autospeed ( E7 )
At the end of a sample interval in the stream mode, the current X and Y data values are converted new values.
The sign bits are not involved in this conversion. The conversion is only in stream mode. The relationship
between the input and output count follows:
Input
0
1
2
3
4
5
N(≥6 )
Ouput
0
1
1
3
6
9
2.0*N
p). Reset Autospeed ( E6 )
This command restore normal speed.
* This specification are subject to be changed without notice.
6.28.1999
8
EM84530
2-IN-ONE MOUSE CONTROLLER
ary
n
i
m
i
l
e
Pr
(III) Microsoft PS/2 scrolling mouse mode:
(A) Entering procedure: Except in WRAP mode, while EM84530 received the following consecutive
command.
i. F3 C8
ii. F3 64
iii. F3 50
---- set sampling rate 200/sec
---- set sampling rate 100/sec
---- set sampling rate 80/sec
(B) Operating:
a. All of the commands in legacy mode still be valid.
b. The ID code of read device type command (F2) will changed from "00" to be "03".
c. Data report will be four bytes format:
Byte
1
2
3
4
Bit
0
1
2
3
4
5
6
7
0-7
0-7
0-7
Description
Left button status; 1 = pressed
Right button status; 1 = pressed
Middle button status; 1 = pressed
Reserve
X data sign; 1 = negative
Y data sign; 1 = negative
X data overflow; 1 = overflow
Y data overflow; 1 = overflow
X data ( D0 - D7 )
Y data ( D0 - D7 )
Reserved ( 0 )
(C) Exiting Microsoft PS/2 mouse mode:
There are two ways to exit:
a. Power off.
b. Reset command (FF).
* This specification are subject to be changed without notice.
6.28.1999
9
EM84530
2-IN-ONE MOUSE CONTROLLER
ABSOLUTE MAXIMUM RATINGS
inary
m
i
l
e
r
P
Parameter
Ratings
Unit
Min.
0
-65
-0.3
-
Temperature under bias
Storage temperature range
Supply voltage
Power dissipation
Max.
70
150
7.5
500
°C
°C
V
mW
DC ELECTRICAL CHARACTERISTICS (TA=25°C to 70°C)
Parameters
Sym.
Min.
Typ.
Max.
IPL
IPh
VPI1
VPI2
Vail
Vaih
Rmi
Ixi
Vopt
Iil
70
0.8
1.5
3.5
18
-18
4.5
0
-
106
1.2
2.1
1.5
56
-56
-1.0
µA
µA
V
V
V
V
µA
µA
V
µA
Iih
Iosc
0
3
-
1.0
3.6
µA
mA
Sym.
Min.
Typ.
Max.
Unit
VDD
IOp
Vt+
4.5
3.2
-
5.5
1
3.8
V
mA
V
Vt -
1.2
-
1.9
V
Idc
Vprl
0.56
-
-
1.86
0.4
mA
V
Parameters
Sym.
Min.
Typ.
Max.
Unit
Operating voltage
VDD
VRTS
IOP1
IOP2
Irts1
Irts2
Irh
Irl
Vrts+
Vrts-
4
3
4
2
9.6
-
5.6
12.2
-
6.2
13
1
1.8
-2
6.8
V
V
mA
mA
mA
mA
mA
mA
V
V
X1,X2,Y1,Y2 low input reference current
X1,X2,Y1,Y2 high input reference current
X1,X2,Y1,Y2 input current
(80µA)
X1,X2,Y1,Y2 input current
(500µA)
L,M,R,OPT input low voltage
L,M,R,OPT input high voltage
L,M,R input current
(Vin=5V)
OPT input current
OPT high output current
(Iopt=20mA)
L,M,R,X1,X2,Y1,Y2 input leakage current
(Vin=0V)
OPT input leakage current
(Vin=5V)
OSC.OUT
Sink current
Unit
PS/2 mouse mode : (TA=25°C to 70°C)
Parameters
Operating voltage
Operating current
CLK, DATA
postive-going threshold voltage
CLK, DATA
negative-going threshold voltage
DATA, CLK input current
DATA,CLK low output voltage
(no load)
(Vin=0V )
(Iprl=-2mA)
Serial mouse mode : (TA=25°C to 70°C)
Operating current
(VDD=5.4V, RTS=VDD)
Operating current
(VDD=6.2V, RTS=VDD)
RTS operating current
(VDD=5.6V, RTS=11V)
RTS operating current
(VDD=5.4V, RTS=12.5V)
RXD high output voltage
(Vrh=Vrts-2.6V)
RXD low output voltage
(Vrl=Vss+2.6V)
RTS high input voltage
RTS low input voltage
* All parameters in above table are compared with VSS
* This specification are subject to be changed without notice.
6.28.1999
10
EM84530
2-IN-ONE MOUSE CONTROLLER
ary
n
i
m
i
l
e
Pr
AC ELECTRICAL CHARACTERISTICS (TA=25°C to 70°C)
PS/2 mouse mode :
Parameters
Sym.
Min.
Oscillating Frequency
Key Debounce
Rising Edge Crossed Width
Falling Edge Crossed Width
Mouse CLK Active Time
Mouse CLK Inactive Time
Time that Mouse Sample DATA from
CLK rising Edge
System CLK Active Time
System CLK Inactive Time
Time from DATA Transition to Falling Edge of CLK
Time from rising Edge of CLK to DATA Transition
Time to mouse Inhibit after the 11th CLK to
ensure mouse does not start another Transmission
Serial mouse mode :
Parameters
Oscillating Frequency
Key Debounce
Rising Edge Crossed Width
Falling Edge Crossed Width
Transmission Time
Start bit Time
Data bit time
Stop bit Time
Mode code delay Time
Typ.
Max.
Unit
Fosc
Tkd
Tr
Tf
Tmca
Tmci
Tmdc
37.0-3%
13.5
13.5
-
37.0
12
40.5
40.5
13.5
37.0+3%
-
KHz
ms
us
us
us
us
us
Tsca
Tsci
Tsdc
Tscd
Tpi
0
40.5
40.5
13.5
27.0
-
50
us
us
us
us
us
Sym.
Min.
Typ.
Max.
Unit
Fosc
Tkd
Tr
Tf
Tmx
Ts
Td
Tp
Trd
32.4-3%
15.4
15.4
11
32.4
13
33.33
833.3
833.3
833.3
-
32.4+3%
14
KHz
ms
us
us
ms
us
us
us
ms
X1, X2,Y1,Y2 Input Impedance
Max.
16.0K
15.0K
Typ.
14.0K
13.0K
12.0K
Min.
11.0K
10.0.K
9.0K
8.0K
7.0K
6.0K
5.0K
4.0K
3.0K
2.0K
1.0K
0
1.0
10.0M
2.0
3.0
4.0
5.0
VOLTS (LIN)
* This specification are subject to be changed without notice.
6.28.1999
11
EM84530
2-IN-ONE MOUSE CONTROLLER
inary
m
i
l
e
r
P
TIMING DIAGRAM
(A) PS/2 mouse mode
(A) Photo-couples pulse width
X1(Y1)
X2(Y2)
Tr
Tf
(B) Receiving Data
1st
CLK
Inhibit
2nd
CLK
9th
CLK
10th
CLK
11th
CLK
CLK
Tmca
Tmci
Tmdc
DATA
Start
Bit
Parity
Bit
Bit0-Bit7
Stop
Bit
Line
Control
Bit
(C) Sending Data
1st
CLK
10th
CLK
2nd
CLK
11th
CLK
CLK
Tsci
Tsca
Tsdc
Tpi
Tscd
DATA
Start
Bit
Bit0-Bit7
* This specification are subject to be changed without notice.
Parity
Bit
Stop
Bit
6.28.1999
12
EM84530
2-IN-ONE MOUSE CONTROLLER
ary
n
i
m
i
l
e
Pr
(B) Serial mouse mode :
(A) RXD output :
Key in/release
Mouse RXD
Tmx
Tmx
(B) Bytes structure :
RXD
1st
2rd
3nd
4nd
(C) Bits structure :
RXD LINE
Data Bit no.
0
Ts Td
1
2
Td Td
4
5
6
Td Td
3
Td
Td
TP Tp
0 1
(D) PnP ID code echo timing :
RTS
><
Trd
RXD
4D 5A 40 00 00
"4D" code
Bit no
Ts
0
1
* This specification are subject to be changed without notice.
2
00 08
3
4
PnP ID code
5
09
Tp Tp
6.28.1999
13
DTR
SG
DSR
RTS
RXD
TXD
7
8
9
4
5
6
1
2
3
GND
+5V
CLK
DATA
1
2
3
4
5
6
* This specification are subject to be changed without notice.
CLK/RTS
VDD
8 V
SS
16 OSCR
EM84530
OSC.OUT
7 OPT
2
6 DATA/RXD
5
1
R
M
L
NC
NC
X1
X2
Y1
Y2
1KΩ
* 50 kΩ must be precise resistor
50K*
5.1V
2 chips analog PT
4 chips digital PT
9
10
11
3
4
12
13
14
15
0.1µF
10µF
EM84530
2-IN-ONE MOUSE CONTROLLER
inary
m
i
l
e
r
P
APPLICATION CIRCUIT
6.28.1999
14
Similar pages