LINER LTC1928-5 Doubler charge pump with low noise linear regulator in thinsot Datasheet

LTC1928-5
Doubler Charge Pump with
Low Noise Linear Regulator
in ThinSOT
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
DESCRIPTIO
Low Output Noise: 90µVRMS (100kHz BW)
Fixed Output Voltage: 5V
Input Voltage Range: 2.7V to 4.4V
No Inductors Required
Uses Small Ceramic Capacitors
Output Current Up to 30mA
550kHz Switching Frequency
Low Operating Current: 190µA
Low Shutdown Current: 4µA
Internal Thermal Shutdown and Current Limiting
Low Profile (1mm) ThinSOTTM Package
U
APPLICATIO S
■
■
■
■
■
■
■
■
The LTC®1928-5 is a doubler charge pump with an internal
low noise, low dropout (LDO) linear regulator. The part is
designed to provide a low noise boosted supply voltage for
powering noise sensitive devices such as high frequency
VCOs in wireless applications.
An internal charge pump converts a 2.7V to 4.4V input to
a boosted output, while the internal LDO regulator converts the boosted voltage to a low noise regulated output.
The regulator is capable of supplying up to 30mA of output
current. Shutdown reduces the supply current to < 8µA,
removes the load from VIN by disabling the regulator and
discharges VOUT to ground through a 200Ω switch.
The LTC1928-5 LDO regulator is stable with only 2µF on
the output. Small ceramic capacitors can be used, reducing PC board area.
VCO Power Supplies for Cellular Phones
2-Way Pagers
Wireless PCMCIA Cards
Portable Medical Instruments
Low Power Data Acquisition
Remote Transmitters
White LED Drivers
GaAs Switches
The LTC1928-5 is short-circuit and overtemperature protected. The part is available in a 6-pin low profile
(1mm)ThinSOT package.
, LTC and LT are registered trademarks of Linear Technology Corporation
ThinSOT is a trademark of Linear Technology Corporation.
U
TYPICAL APPLICATION
Output Noise (BW = 10Hz to 2.5MHz)
LTC1928-5
VIN
2.7V TO 4.4V
1
4.7µF
0.47µF
5
6
VIN
CP
VOUT
CPO
CN/SHDN GND
5V
3
4
2
VOUT
4.7µF
4.7µF
VOUT
200µV/DIV
19285 F01
Figure 1. Low Noise 5V Power Supply
CCPO = COUT = 4.7µF 100µs/DIV
IOUT = 10mA
VIN = 3V
VOUT = 5V
TA = 25°C
19285 TA01
1
LTC1928-5
W W
W
AXI U
U
ABSOLUTE
RATI GS
U
U
W
PACKAGE/ORDER I FOR ATIO
(Note 1)
VIN to Ground ..............................................– 0.3V to 5V
VOUT Voltage ...........................................– 0.3V to 5.25V
CPO to Ground ........................................................ 10V
CN/SHDN to Ground ..................... – 0.3V to (VIN + 0.3V)
VOUT Short-Circuit Duration ............................. Indefinite
IOUT ......................................................................................... 40mA
Operating Temperature Range (Note 2) ...–40°C to 85°C
Maximum Junction Temperature ......................... 125°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
ORDER PART
NUMBER
TOP VIEW
VIN 1
6 CN/SHDN
GND 2
5 CP
VOUT 3
4 CPO
LTC1928ES6-5
S6 PART MARKING
S6 PACKAGE
6-LEAD PLASTIC SOT-23
TJMAX = 125°C, θJA = 230°C/ W
LTKT
Consult factory for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C.
VIN = 3V, CFLY = 0.47µF, COUT, CCPO, CIN = 4.7µF unless otherwise specified.
PARAMETER
CONDITIONS
MIN
VIN Operating Voltage
TYP
UNITS
4.4
V
IVIN Shutdown Current
SHDN = 0V (Note 5)
●
4
8
µA
IVIN Operating Current
IOUT = 0mA, Burst ModeTM Operation
●
190
330
µA
Regulated Output Voltage
IOUT = 1mA
●
5
5.1
●
2.7
MAX
4.9
±50
VOUT Temperature Coefficient
Charge Pump Oscillator Frequency
IOUT > 500µA, VIN = 2.7V to 4.4V
●
CPO Output Resistance
VIN = 2.7V, IOUT = 10mA
VIN = 4.4V, IOUT = 10mA
●
●
VOUT Dropout Voltage (Note 3)
IOUT = 10mA, VOUT = 5V
●
480
V
ppm
550
620
kHz
17
14
30
24
Ω
Ω
100
mV
VOUT Enable Time
RLOAD = 2k
0.6
ms
VOUT Output Noise Voltage
IOUT = 10mA, 10Hz ≤ f ≤ 100kHz
IOUT = 10mA, 10Hz ≤ f ≤ 2.5MHz
90
800
µVRMS
µVP-P
VOUT Line Regulation
VIN = 2.7V to 4.4V, IOUT = 0
●
4
20
mV
VOUT Load Regulation
IOUT = 1mA to 10mA
IOUT = 1mA to 30mA (Note 4)
●
2
4
10
mV
mV
VOUT Shutdown Resistance
CN/SHDN = 0V (Note 5)
VIN = 2.7V, Resistance Measured to Ground
VIN = 4.4V, Resistance Measured to Ground
●
●
160
100
400
300
Ω
Ω
CN/SHDN Input Threshold
VIN = 2.7V to 4.4V (Note 5)
●
0.15
0.5
1.6
V
CN/SHDN Input Current
CN/SHDN = 0V (Note 5)
●
–1
–3
–6
µA
Burst Mode is a trademark of Linear Technology Corporation.
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: The LTC1928ES6-5 is guaranteed to meet performance
specifications from 0°C to 70°C. Specifications over the – 40°C to 85°C
operating temperature range are assured by design, characterization and
correlation with statistical process controls.
2
Note 3: Dropout voltage is the minimum input/output voltage required to
maintain regulation at the specified output current. In dropout the output
voltage will be equal to: VCPO – VDROPOUT (see Figure 2).
LTC1928-5
ELECTRICAL CHARACTERISTICS
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output specification will not apply for all
possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range may be
limited. When operating at maximum output current, the input voltage
range may be limited.
Note 5: CN/SHDN must be driven with a source impedance of at least
100Ω (RSOURCE) to prevent damage to the part. This pin is multiplexed
and may be connected through a low switch impedance to VIN. There may
be a large amount of current (VIN/RSOURCE) until the shutdown state
occurs after which the charge pump switches at CN/SHDN become high
impedance and the current will fall to < 8µA.
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Min and Max VCPO vs VIN
9
TA = 25°C
CFLY = 0.47µF
30 IOUT = 10mA
VOUT Transient Response
10
TA = 25°C
∆VOUT (mV)
CPO Output Resistance vs VIN
35
8
VCPO = 2(VIN)
7
VCPO (V)
RCPO (Ω)
25
20
(A)
6
(B)
IOUT (mA)
4
10
3
3.0
3.5
VIN (V)
4.0
2.5
4.5
3.0
3.5
VIN (V)
TA = 25°C
VIN = 3V
VOUT = 5V
COUT = 4.7µF
–5
15
15
5
2.5
0
–10
VCPO = 1.45(VIN)
5
5
4.0
10
5
0
4.5
0
50
100
150
200
TIME (µs)
250
(A) THE MAXIMUM GENERATED NO LOAD
CPO VOLTAGE
(B) THE MINIMUM ALLOWABLE CPO VOLTAGE,
AT FULL LOAD, TO ENSURE THAT THE LDO
IS NOT DISABLED
19285 G02
19285 G01
Shutdown to Enable Timing
(Figure 5)
300
19285 G03
Enable to Shutdown Timing
(Figure 5)
VOUT Voltage vs Temperature
0
2
5
5
4
4
3
2
1
0
TA = 25°C
VIN = 3V
VOUT = 5V
IOUT = 10mA
COUT = CCPO = 4.7µF
200µs/DIV
19285 G04
5.030
VIN = 3V
IOUT = 10mA
0
VOUT VOLTAGE (V)
SHDN (V)
2
VOUT (V)
VOUT (V)
SHDN (V)
5.040
3
2
1
0
NO LOAD
TA = 25°C
VIN = 3V
VOUT = 5V
COUT = 4.7µF
5.020
5.010
5.000
4.990
4.980
–50 –25
1ms/DIV
19285 G05
50
25
75
0
TEMPERATURE (°C)
100
125
19285 G06
3
LTC1928-5
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Operating Current vs VIN
(No Load)
260
Efficiency vs Supply Voltage
100
TA = 25°C
TA = 25°C
IOUT = 15mA
CFLY = 0.47µF
90
180
160
OUTPUT VOLTAGE (V)
200
80
70
60
140
4.989
4.988
4.987
4.986
4.985
4.984
50
120
100
2.5
TA = 25°C
VIN = 3V
CFLY = 0.47µF
4.900
220
EFFICIENCY (%)
OPERATING CURRENT (µA)
240
Output Voltage vs Output Current
4.901
4.983
4.982
40
3.0
3.5
VIN (V)
4.0
0
2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4
SUPPLY VOLTAGE (V)
4.5
19285 G07
5
10 15 20 25 30
OUTPUT CURRENT (mA)
W
CFLY
0.47µF
CIN
4.7µF
1
6
CN/SHDN
CHARGE PUMP
AND
SLEW CONTROL
4
CPO
CCPO
4.7µF
–
VIN
5
ENB
CLK B
+
+
POR/
SHDN
CONTROL
BURST
550kHz
OSCILLATOR
–
SD
+
–
VOUT
3
VREF = 1.235V
COUT
4.7µF
160Ω
SD
2
19285 BD
GND
4
40
19285 G09
19285 G08
BLOCK DIAGRA
CP
35
LTC1928-5
U
U
U
PIN FUNCTIONS
VIN (Pin 1): Input Voltage, 2.7V to 4.4V. VIN should be
bypassed with a ≥ 2µF low ESR capacitor as close to the
pin as possible for best performance. A minimum capacitance value of 0.1µF is required.
GND (Pin 2): System Ground.
VOUT (Pin 3): Low Noise Regulated Output Voltage. VOUT
should be bypassed with a ≥ 2µF low ESR capacitor as
close to the pin as possible for best performance. The VOUT
voltage is internally set to 5V.
CPO (Pin 4): Boosted Unregulated Voltage. Approximately 1.95VIN at low loads. Bypass with a ≥ 2µF low ESR
capacitor.
CP (Pin 5): Flying Capacitor Positive Input.
CN/SHDN (Pin 6): Flying Capacitor Negative Input and
SHDN. When this pin is pulled to ground through a 100Ω
resistor, the part will go into shutdown within approximately 30µs.
U
W
U
U
APPLICATIONS INFORMATION
Operation
The LTC1928-5 uses a switched-capacitor charge pump
to generate a CPO voltage of approximately 2VIN. CPO
powers an internal low dropout linear regulator that supplies a regulated output at VOUT. Internal comparators are
used to sense CPO and VIN voltages for power-up conditioning. The output current is sensed to determine the
charge pump operating mode. A trimmed internal bandgap
is used as the voltage reference and a trimmed internal
oscillator is used to control the charge pump switches.
The charge pump is a doubler configuration that uses one
external flying capacitor. When enabled, a 2-phase
nonoverlapping clock controls the charge pump switches.
At start-up, the LDO is disabled and the load is removed
from CPO. When CPO reaches 1.75VIN the LDO is enabled.
If CPO falls below 1.45VIN the LDO will be disabled. Generally, the charge pump runs open loop with continuous
clocking for low noise. If CPO is greater than 1.95VIN and
IOUT is less than 200µA, the charge pump will operate in
Burst Mode operation for increased efficiency but slightly
higher output noise. In Burst Mode operation, the clock is
disabled when CPO reaches 1.95VIN and enabled when
CPO droops by about 150mV. The switching frequency is
precisely controlled to ensure that the frequency is above
455kHz and at the optimum rate to ensure maximum efficiency. The switch edge rates are also controlled to minimize noise. The effective output resistance at CPO is
dependent on the voltage at VIN, CPO, the flying capacitor
value CFLY and the junction temperature. A low ESR capacitor of ≥2µF should be used at CPO for minimum noise.
The LDO is used to filter the ripple on CPO and to set an
output voltage independent of CPO. VOUT is set by an
internal reference and resistor divider. The LDO requires a
capacitor on VOUT for stability and improved load transient
response. A low ESR capacitor of ≥2µF should be used.
Maximum IOUT Calculations
The maximum available current can be calculated based
on the open circuit CPO voltage, the dropout voltage of the
LDO and the effective output resistance of the charge
pump. The open circuit CPO voltage is approximately 2VIN
(see Figure 2).
Example:
VIN = 3V
VOUT = 5V
RCPO = 30Ω
Maximum unloaded CPO voltage = 2VIN = 6V
VDROPOUT(MAX) = 100mV
IOUT(MAX) = (2VIN – VDROPOUT(MAX) – VOUT)/RCPO
= (6V – 0.1V – 5V)/30Ω = 30mA
VCPO must be greater than 1.45VIN = 4.35V. To confirm
this, calculate VCPO:
VCPO = 6V – (30mA • 30Ω) = 5.1V
For minimum noise applications the LDO must be kept out
of dropout to prevent CPO noise from coupling into VOUT.
5
LTC1928-5
W
U
U
VCPO
U
RCPO
APPLICATIONS INFORMATION
RDROPOUT
+
+ 2V
IN
–
–
VOUT
VDROPOUT
CCPO
IOUT
19285 F02
Figure 2. Equivalent Circuit
External CPO Loading
The CPO output can drive an external load (for example, an
LDO). The current required by this additional load will
reduce the available current from VOUT. If the external load
requires 1mA, the available current at VOUT will be reduced
by 1mA.
Short-Circuit and Thermal Protection
VOUT can be shorted to ground indefinitely. Internal circuitry will limit the output current. If the junction temperature exceeds 150°C the part will shut down. Excessive
power dissipation due to heavy loads will also cause the
part to shut down when the junction temperature exceeds
150°C. The part will become enabled when the junction
temperature drops below 140°C. If the fault conditions
remain in place, the part will cycle between the shutdown
and enabled states.
Capacitor Selection
For best performance it is recommended that low ESR
ceramic capacitors be used to reduce noise and ripple.
COUT must be ≥ 2µF and CCPO must be equal to or greater
than COUT. CIN is dependent on the input power supply
source impedance. The charge pump demands large
instantaneous currents which may induce ripple onto a
common voltage rail. CIN should be ≥ 2 µF and a spike
reducing resistor of 2.2Ω may be required between VIN
and the supply.
6
A low ESR ceramic capacitor is recommended for the
flying capacitor CFLY with a value of 0.47µF. At low load or
high VIN a smaller capacitor could be used to reduce ripple
on CPO which would reflect as lower ripple on VOUT.
If a minimum enable time is required, the CPO output filter
capacitor should be at least 2× the VOUT filter capacitor.
When the LDO is first enabled, the CPO capacitor will
dump a large amount of charge into the VOUT capacitor. If
the drop in the CPO voltage falls below 1.45VIN the LDO
will be disabled and the CPO voltage will be required to
charge up to 1.75VIN to enable the LDO. The resulting
cycling extends the enable time.
Output Ripple
The output ripple on CPO includes a spike component
from the charge pump switches and a droop component
which is dependent on the load current and the value of C3.
The charge pump has been carefully designed to minimize
the spike component, however, low ESR capacitors are
essential to reduce the remaining spike energy effect on
the CPO voltage. CCPO should be increased for high load
currents to minimize the droop component. Ripple components on CPO are greatly reduced at VOUT by the LDO,
however, COUT should also be a low ESR capacitor to
improve filtering of the CPO noise.
Shutdown
When CN/SHDN = 0V, the part will be in shutdown, the
supply current will be < 8µA and VOUT will be shorted to
ground through a 160Ω switch. In addition, CPO will be
high impedance and disconnected from V IN and
CN/SHDN.
Shutdown is achieved by internally sampling the
CN/SHDN pin for a low voltage. Time between shutdown
samples is about 30µs. During the sample time the charge
pump switches are disabled and CN/SHDN must be pulled
to ground within 400ns. A resistor value between 100Ω
and 1k is recommended. Parasitic lead capacitance should
be minimized on the CN/SHDN pin.
LTC1928-5
U
U
W
U
APPLICATIONS INFORMATION
Power-On Reset
General Layout Considerations
Upon initial power-up, a power-on reset circuit ensures
that the internal functions are correctly initialized. Once
VIN reaches about 1V, the power-on reset circuit will
enable the part as long as the CN/SHDN pin is not pulled
low.
Due to the high switching frequency and high transient
currents produced by the device, careful board layout is a
must. A clean board layout using a ground plane and short
connections to all capacitors will improve noise performance and ensure proper regulation.
Thermal Considerations
Measuring Output Noise
The power handling capability of the device will be limited
by the maximum rated junction temperature (125°C). The
device dissipation PD = IOUT(2VIN – VOUT) + VIN(2mA). The
device dissipates the majority of its heat through its pins,
especially GND (Pin 2). Thermal resistance to ambient can
be optimized by connecting GND to a large copper region
on the PCB, which serves as a heat sink. Applications that
operate the LTC1928-5 near maximum power levels should
maximize the copper area at all pins except CP and
CN/SHDN and ensure that there is some airflow over the
part to carry away excess heat.
Measuring the LTC1928 low noise levels requires care.
Figure 3 shows a test setup for taking the measurement.
Good connection and signal handling technique should
yield about 800µVP-P over a 2.5MHz bandwidth. The noise
measurement involves AC coupling the LTC1928 output
into the test setup’s input and terminating this connection
with 50Ω. Coaxial connections must be maintained to
preserve measurement integrity.
BNC CABLES
OR COUPLERS
BATTERY OR
LOW NOISE DC
POWER SUPPLY
COUPLING
CAPACITOR
LTC1928 VOUT
DEMO
BOARD
+
CONNECT BNC AND
RLOAD GROUND TO THE
OUTPUT CAPACITOR
GROUND TERMINAL
–
R*
RLOAD
PREAMP
1822
INPUT
BANDWIDTH
FILTER
10×
OSCILLOSCOPE
R*
PLACE BANDWIDTH FILTER
COMPONENTS IN SHIELDED BOX
WITH COAXIAL CONNECTORS
R*
PLACE COUPLING
CAPACITOR IN SHIELDED
BOX WITH COAXIAL
CONNECTOR
*50Ω TERMINATIONS
HP-11048C OR
EQUIVALENT
NOTE: KEEP BNC CONNECTIONS
AS SHORT AS POSSIBLE
19285 F03
Figure 3. LTC1928-5 Noise Measurement Test Setup
VRIPPLE < 800µVP-P
5V
VIN
3V
COUT
4.7µF
LTC1928-5
3
2
1
CIN
4.7µF
VOUT
CPO
GND
CP
VIN
CN/SHDN
ADDITIONAL
LDO
4
5
6
CFLY
0.47µF
CCPO
4.7µF
IN
OUT
3.3V
GND
10µF
19285 F04
Figure 4. LTC1928-5, External Load on CPO, No Shutdown State
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
7
LTC1928-5
U
U
W
U
APPLICATIONS INFORMATION
VIN
2.7V TO 4.4V
CIN
4.7µF
LTC1928-5
1
5
CFLY
0.47µF
6
VIN
VOUT
CP
CPO
CN/SHDN GND
3
VRIPPLE < 800µVP-P
4
2
CCPO
4.7µF
19285 F05
100Ω
2N7002
5V
COUT
4.7µF
SHDN
Figure 5. Low Noise 5V Supply with Shutdown
U
PACKAGE DESCRIPTION
S6 Package
6-Lead Plastic SOT-23
SOT-23
(Original)
SOT-23
(ThinSOT)
A
.90 – 1.45
(.035 – .057)
1.00 MAX
(.039 MAX)
A1
.00 – 0.15
(.00 – .006)
.01 – .10
(.0004 – .004)
A2
.90 – 1.30
(.035 – .051)
.80 – .90
(.031 – .035)
L
.35 – .55
(.014 – .021)
.30 – .50 REF
(.012 – .019 REF)
(Reference LTC DWG # 05-08-1634)
(Reference LTC DWG # 05-08-1636)
2.80 – 3.10
(.110 – .118)
(NOTE 3)
.20
(.008)
A
DATUM ‘A’
A2
2.60 – 3.00
1.50 – 1.75
(.102 – .118) (.059 – .069)
(NOTE 3)
L
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
.09 – .20
(.004 – .008)
(NOTE 2)
1.90
(.074)
REF
PIN ONE ID
A1
3. DRAWING NOT TO SCALE
4. DIMENSIONS ARE INCLUSIVE OF PLATING
5. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
6. MOLD FLASH SHALL NOT EXCEED .254mm
7. PACKAGE EIAJ REFERENCE IS:
SC-74A (EIAJ) FOR ORIGINAL
JEDEL MO-193 FOR THIN
.95
(.037)
REF
.25 – .50
(.010 – .020)
(6PLCS, NOTE 2)
S6 SOT-23 0401
RELATED PARTS
PART NUMBER
DESCRIPTION
LTC1550/LTC1551
Low Noise, 900kHz Charge Pump
1mVP-P Typical Ripple, Up to 10mA
LT1611
Inverting 1.4MHz Switching Regulator
5V to –5V at 150mA, Low Output Noise
LT1613
1.4MHz Boost Switching Regulator in ThinSOT
3.3V to 5V at 200mA, Low Noise PWM Operation
LTC1682
Doubler Charge Pump with Low Noise Linear Regulator
60µVRMS Noise, IOUT up to 80mA, MSOP
LTC1754-5
Micropower 5V Charge Pump in ThinSOT
IQ = 13µA, IOUT to 50mA, Shutdown
LT1761 Series
100mA ThinSOT, Low Noise LDO Regulators
20µA IQ, 20µVRMS Noise, 300mV Dropout
LTC3200
Constant Frequency Doubler Charge Pump
Low Noise, 5V Output or Adjustable
8
Linear Technology Corporation
COMMENTS
1928f LT/TP 0601 2K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
 LINEAR TECHNOLOGY CORPORATION 2000
Similar pages