EIC AWL10G Avalanche glass passivated bridge rectifier Datasheet

AWL005G - AWL10G AVALANCHE GLASS PASSIVATED
BRIDGE RECTIFIERS
PRV : 50 - 1000 Volts
Io : 1.0 Ampere
WOB
0.39 (10.0)
0.31 (7.87)
FEATURES :
Glass passivated chip
High case dielectric strength
High surge current capability
High reliability
Low reverse current
Low forward voltage drop
Ideal for printed circuit board
0.22 (5.59)
0.18 (4.57)
+
-
AC
1.00 (25.4)
MIN.
1.10 (27.9)
MIN.
*
*
*
*
*
*
*
0.034 (0.86)
0.028 (0.71)
MECHANICAL DATA :
* Case : Reliable low cost construction
utilizing molded plastic technique
* Epoxy : UL94V-O rate flame retardant
* Terminals : Plated leads solderable per
MIL-STD-202, Method 208 guaranteed
* Polarity : Polarity symbols marked on case
* Mounting position : Any
* Weight : 1.29 grams
AC
+
-
0.22 (5.59)
0.18 (4.57)
AC
0.22 (5.59)
0.18 (4.57)
Dimension in inches and (millimeter)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25 °C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
RATING
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Minimum Avalanche Breakdown Voltage at 100 µA
Maximum Avalanche Breakdown Voltage at 100 µA
Maximum Average Forward Current
0.375" (9.5 mm) lead length
Tc = 50°C
Peak Forward Surge Current Single half sine wave
Superimposed on rated load (JEDEC Method)
Rating for fusing ( t < 8.3 ms. )
Maximum Forward Voltage per Diode at IF = 1.0 Amp.
Maximum DC Reverse Current
Ta = 25 °C
at Rated DC Blocking Voltage
Ta = 100 °C
Typical Junction Capacitance per Diode (Note 1)
Typical Thermal Resistance (Note 2)
Operating Junction Temperature Range
Storage Temperature Range
SYMBOL
VRRM
VRMS
VDC
VBO(min.)
VBO(max.)
AWL AWL
005G 01G
50
100
35
70
50
100
100
150
550
600
AWL
02G
200
140
200
250
700
AWL
04G
400
280
400
450
900
AWL
06G
600
420
600
700
1150
AWL
08G
800
560
800
900
1350
AWL
10G
1000
700
1000
1100
1550
UNIT
Volts
Volts
Volts
Volts
Volts
IF(AV)
1.0
Amps.
IFSM
30
10
1.2
10
1.0
24
36
- 50 to + 150
- 50 to + 150
Amps.
I2t
VF
IR
IR(H)
CJ
RθJA
TJ
TSTG
Notes :
1 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts.
2 ) Thermal resistance from Junction to Ambient at 0.375" (9.5 mm) lead length P.C. Board mounting.
A2S
Volts
µA
mA
pf
°C/W
°C
°C
UPDATE : APRIL 23,1998
RATING AND CHARACTERISTIC CURVES ( AWL005G - AWL10G )
FIG.1 - DERATING CURVE FOR OUTPUT
RECTIFIED CURRENT
FIG.2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
30
PC Board
0.375(9.5mm)
0.8
Copper Pads
0.22" x 0.22"
(5.5 x5.5mm)
0.6
0.4
0.2
60 Hz, Resistive or Inductive load.
0
0
25
50
75
100
125
150
PEAK FORWARD SURGE
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
1.0
24
18
12
SINGLE HALF SINE WAVE
(JEDEC METHOD)
6
0
175
TJ = 55 °C
1
CASE TEMPERATURE, ( °C)
20
10
1
TJ = 25 °C
Pulse Width = 300 µs
1 % Duty Cycle
0.01
0.4
0.6
0.8
1.0
1.2
1.4
1.6
FORWARD VOLTAGE, VOLTS
4
6
10
20
40
60
100
FIG.4 - TYPICAL REVERSE CHARACTERISTICS
REVERSE CURRENT, MICROAMPERES
FORWARD CURRENT, AMPERES
FIG.3 - TYPICAL FORWARD CHARACTERISTICS
0.1
2
NUMBER OF CYCLES AT 60Hz
1.8
10
TJ = 100 °C
1.0
TJ = 25 °C
0.1
0.01
0
20
40
60
80
100
120
PERCENT OF RATED REVERSE
VOLTAGE, (%)
140
Similar pages