IRF AUIRF1405ZL Hexfetâ® power mosfet Datasheet

PD - 97486A
AUIRF1405ZS
AUIRF1405ZL
AUTOMOTIVE GRADE
Features
l
l
l
l
l
l
l
HEXFET® Power MOSFET
Advanced Process Technology
Ultra Low On-Resistance
175°C Operating Temperature
Fast Switching
Repetitive Avalanche Allowed up to
Tjmax
Lead-Free, RoHS Compliant
Automotive Qualified *
D
V(BR)DSS
55V
RDS(on) max.
G
ID
S
Description
150A
D
D
Specifically designed for Automotive applications,
this HEXFET® Power MOSFET utilizes the latest
processing techniques to achieve extremely low onresistance per silicon area. Additional features of
this design are a 175°C junction operating
temperature, fast switching speed and improved
repetitive avalanche rating . These features combine
to make this design an extremely efficient and reliable
device for use in Automotive applications and a wide
variety of other applications.
4.9mΩ
G
D
S
G
D
S
D2Pak
TO-262
AUIRF1405ZS AUIRF1405ZL
G
Gate
D
Drain
S
Source
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These
are stress ratings only; and functional operation of the device at these or any other condition beyond those indicated in
the specifications is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions.
Ambient temperature (T A) is 25°C, unless otherwise specified.
Parameter
ID @ TC = 25°C
ID @ TC = 100°C
IDM
PD @TC = 25°C
VGS
EAS
EAS (tested )
IAR
EAR
TJ
TSTG
Max.
c
Pulsed Drain Current
Power Dissipation
Linear Derating Factor
Gate-to-Source Voltage
Single Pulse Avalanche Energy (Thermally Limited)
Single Pulse Avalanche Energy Tested Value
Avalanche Current
Repetitive Avalanche Energy
Operating Junction and
Storage Temperature Range
Soldering Temperature, for 10 seconds (1.6mm from case )
Mounting Torque, 6-32 or M3 screw
c
h
g
d
Parameter
Junction-to-Case
RθJA
Junction-to-Ambient (PCB Mount, steady state)
i
A
W
1.5
± 20
270
420
See Fig.12a, 12b, 15, 16
W/°C
V
mJ
A
mJ
-55 to + 175
°C
300
10 lbf in (1.1N m)
y
Thermal Resistance
RθJC
Units
150
110
600
230
Continuous Drain Current, VGS @ 10V
Continuous Drain Current, VGS @ 10V
y
Typ.
Max.
Units
–––
0.65
°C/W
–––
40
HEXFET® is a registered trademark of International Rectifier.
*Qualification standards can be found at http://www.irf.com/
www.irf.com
1
07/01/2010
AUIRF1405ZS/L
Static Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Parameter
V(BR)DSS
∆V(BR)DSS/∆TJ
RDS(on)
VGS(th)
Min. Typ. Max. Units
gfs
IDSS
Drain-to-Source Breakdown Voltage
Breakdown Voltage Temp. Coefficient
Static Drain-to-Source On-Resistance
Gate Threshold Voltage
Forward Transconductance
Drain-to-Source Leakage Current
IGSS
Gate-to-Source Forward Leakage
55
–––
–––
2.0
88
–––
–––
–––
Gate-to-Source Reverse Leakage
–––
–––
0.049
3.7
–––
–––
–––
–––
–––
–––
–––
4.9
4.0
–––
20
250
200
–––
-200
Conditions
V VGS = 0V, ID = 250µA
V/°C Reference to 25°C, ID = 1mA
mΩ VGS = 10V, ID = 75A
V VDS = VGS, ID = 250µA
S VDS = 25V, ID = 75A
µA VDS = 55V, VGS = 0V
VDS = 55V, VGS = 0V, TJ = 125°C
nA VGS = 20V
e
VGS = -20V
Dynamic Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Qg
Qgs
Qgd
td(on)
tr
td(off)
tf
LD
Total Gate Charge
Gate-to-Source Charge
Gate-to-Drain ("Miller") Charge
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
Internal Drain Inductance
–––
–––
–––
–––
–––
–––
–––
–––
120
31
46
18
110
48
82
4.5
180
–––
–––
–––
–––
–––
–––
–––
nC
ns
nH
ID = 75A
VDS = 44V
VGS = 10V
VDD = 25V
ID = 75A
RG = 4.4Ω
VGS = 10V
Between lead,
e
e
D
LS
Internal Source Inductance
–––
7.5
–––
6mm (0.25in.)
from package
Ciss
Coss
Crss
Coss
Coss
Coss eff.
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Output Capacitance
Output Capacitance
Effective Output Capacitance
–––
–––
–––
–––
–––
–––
4780
770
410
2730
600
910
–––
–––
–––
–––
–––
–––
S
and center of die contact
VGS = 0V
VDS = 25V
ƒ = 1.0MHz
VGS = 0V, VDS = 1.0V, ƒ = 1.0MHz
VGS = 0V, VDS = 44V, ƒ = 1.0MHz
VGS = 0V, VDS = 0V to 44V
pF
G
f
Diode Characteristics
Parameter
Min. Typ. Max. Units
IS
Continuous Source Current
–––
–––
75
ISM
(Body Diode)
Pulsed Source Current
–––
–––
600
VSD
trr
Qrr
ton
Diode Forward Voltage
Reverse Recovery Time
Reverse Recovery Charge
Forward Turn-On Time
–––
–––
–––
–––
30
30
1.3
46
45
(Body Diode)c
A
V
ns
nC
D
showing the
integral reverse
G
S
p-n junction diode.
TJ = 25°C, IS = 75A, VGS = 0V
TJ = 25°C, IF = 75A, VDD = 25V
di/dt = 100A/µs
e
e
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
Notes:
 Repetitive rating; pulse width limited by
max. junction temperature. (See fig. 11).
‚ Limited by TJmax, starting TJ = 25°C, L = 0.10mH
†
RG = 25Ω, IAS = 75A, VGS =10V. Part not
recommended for use above this value.
ƒ Pulse width ≤ 1.0ms; duty cycle ≤ 2%.
‡
„ Coss eff. is a fixed capacitance that gives the same
charging time as Coss while VDS is rising from 0 to 80%
VDSS .
2
Conditions
MOSFET symbol
Limited by TJmax , see Fig.12a, 12b, 15, 16 for typical
repetitive avalanche performance.
This value determined from sample failure population,
starting TJ = 25°C, L = 0.10mH, RG = 25Ω, IAS = 75A,
VGS =10V.
This is applied to D 2Pak, when mounted on 1" square PCB
( FR-4 or G-10 Material ). For recommended footprint and
soldering techniques refer to application note #AN-994.
www.irf.com
AUIRF1405ZS/L
Qualification Information†
Automotive
(per AEC-Q101)
††
Comments: This part number(s) passed Automotive
qualification. IR’s Industrial and Consumer qualification
level is granted by extension of the higher Automotive
level.
Qualification Level
Moisture Sensitivity Level
Machine Model
TO-262
2
D Pak
N/A
MSL1
Class M4 (425V)
AEC-Q101-002
ESD
Human Body Model
AEC-Q101-001
Charged Device
Model
RoHS Compliant
†
Class H1C (2000V)
Class C5 (1125V)
AEC-Q101-005
Yes
Qualification standards can be found at International Rectifier’s web site: http//www.irf.com/
†† Exceptions to AEC-Q101 requirements are noted in the qualification report.
www.irf.com
3
AUIRF1405ZS/L
1000
1000
100
BOTTOM
TOP
10
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
TOP
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
4.5V
100
BOTTOM
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
4.5V
10
20µs PULSE WIDTH
Tj = 175°C
20µs PULSE WIDTH
Tj = 25°C
1
1
0.1
1
10
100
0.1
Fig 1. Typical Output Characteristics
100
Fig 2. Typical Output Characteristics
200
Gfs, Forward Transconductance (S)
1000
ID, Drain-to-Source Current (Α)
10
VDS, Drain-to-Source Voltage (V)
VDS, Drain-to-Source Voltage (V)
T J = 150°C
100
T J = 25°C
10
VDS = 25V
20µs PULSE WIDTH
175
150
T J = 25°C
125
100
T J = 175°C
75
50
25
0
1
4
6
8
10
VGS, Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
4
1
12
0
25
50
75
100 125 150 175 200
ID,Drain-to-Source Current (A)
Fig 4. Typical Forward Transconductance
vs. Drain Current
www.irf.com
nce
AUIRF1405ZS/L
100000
12.0
VGS = 0V,
f = 1 MHZ
C iss = C gs + C gd, C ds SHORTED
C rss = C gd
VGS, Gate-to-Source Voltage (V)
ID= 75A
C, Capacitance(pF)
C oss = C ds + C gd
10000
C iss
Coss
1000
Crss
VDS= 44V
VDS= 28V
10.0
8.0
6.0
4.0
2.0
100
0.0
1
10
100
0
VDS, Drain-to-Source Voltage (V)
40
60
80
100
120
QG Total Gate Charge (nC)
Fig 6. Typical Gate Charge vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance vs.
Drain-to-Source Voltage
10000
ID, Drain-to-Source Current (A)
1000.00
ISD, Reverse Drain Current (A)
20
T J = 175°C
100.00
OPERATION IN THIS AREA
LIMITED BY R DS(on)
1000
10.00
100
T J = 25°C
1.00
VGS = 0V
0.10
0.0
0.5
1.0
1.5
2.0
VSD, Source-to-Drain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
www.irf.com
2.5
100µsec
10
Tc = 25°C
Tj = 175°C
Single Pulse
1msec
10msec
1
1
10
100
1000
VDS, Drain-to-Source Voltage (V)
Fig 8. Maximum Safe Operating Area
5
AUIRF1405ZS/L
150
RDS(on) , Drain-to-Source On Resistance
(Normalized)
2.5
ID, Drain Current (A)
125
100
75
50
25
0
25
50
75
100
125
150
175
ID = 75A
VGS = 10V
2.0
1.5
1.0
0.5
-60 -40 -20 0
T C , Case Temperature (°C)
20 40 60 80 100 120 140 160 180
T J , Junction Temperature (°C)
Fig 10. Normalized On-Resistance
vs. Temperature
Fig 9. Maximum Drain Current vs.
Case Temperature
1
Thermal Response ( Z thJC )
D = 0.50
0.20
0.1
0.10
0.05
0.02
0.01
0.01
SINGLE PULSE
( THERMAL RESPONSE )
Notes:
1. Duty Factor D = t1/t2
2. Peak Tj = P dm x Zthjc + Tc
0.001
1E-006
1E-005
0.0001
0.001
0.01
0.1
1
10
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
6
www.irf.com
AUIRF1405ZS/L
DRIVER
L
VDS
D.U.T
RG
+
V
- DD
IAS
20V
VGS
A
0.01Ω
tp
Fig 12a. Unclamped Inductive Test Circuit
V(BR)DSS
EAS , Single Pulse Avalanche Energy (mJ)
500
15V
ID
31A
53A
BOTTOM 75A
TOP
400
300
200
100
0
tp
25
50
75
100
125
150
175
Starting T J , Junction Temperature (°C)
I AS
Fig 12c. Maximum Avalanche Energy
vs. Drain Current
Fig 12b. Unclamped Inductive Waveforms
QG
10 V
QGS
QGD
VG
Charge
Fig 13a. Basic Gate Charge Waveform
Current Regulator
Same Type as D.U.T.
50KΩ
12V
VGS(th) Gate threshold Voltage (V)
4.0
3.5
3.0
2.5
ID = 250µA
2.0
1.5
.2µF
.3µF
1.0
D.U.T.
+
V
- DS
VGS
-75 -50 -25
0
25
50
75 100 125 150 175 200
T J , Temperature ( °C )
3mA
IG
ID
Current Sampling Resistors
Fig 14. Threshold Voltage vs. Temperature
Fig 13b. Gate Charge Test Circuit
www.irf.com
7
AUIRF1405ZS/L
10000
Avalanche Current (A)
Duty Cycle = Single Pulse
1000
Allowed avalanche Current vs
avalanche pulsewidth, tav
assuming ∆ Tj = 25°C due to
avalanche losses
0.01
100
0.05
0.10
10
1
1.0E-08
1.0E-07
1.0E-06
1.0E-05
1.0E-04
1.0E-03
1.0E-02
1.0E-01
tav (sec)
Fig 15. Typical Avalanche Current vs.Pulsewidth
EAR , Avalanche Energy (mJ)
300
TOP
Single Pulse
BOTTOM 10% Duty Cycle
ID = 75A
250
200
150
100
50
0
25
50
75
100
125
150
Starting T J , Junction Temperature (°C)
Fig 16. Maximum Avalanche Energy
vs. Temperature
8
175
Notes on Repetitive Avalanche Curves , Figures 15, 16:
(For further info, see AN-1005 at www.irf.com)
1. Avalanche failures assumption:
Purely a thermal phenomenon and failure occurs at a
temperature far in excess of T jmax. This is validated for
every part type.
2. Safe operation in Avalanche is allowed as long asT jmax is
not exceeded.
3. Equation below based on circuit and waveforms shown in
Figures 12a, 12b.
4. PD (ave) = Average power dissipation per single
avalanche pulse.
5. BV = Rated breakdown voltage (1.3 factor accounts for
voltage increase during avalanche).
6. Iav = Allowable avalanche current.
7. ∆T = Allowable rise in junction temperature, not to exceed
Tjmax (assumed as 25°C in Figure 15, 16).
tav = Average time in avalanche.
D = Duty cycle in avalanche = tav ·f
ZthJC(D, tav ) = Transient thermal resistance, see figure 11)
PD (ave) = 1/2 ( 1.3·BV·Iav) = DT/ ZthJC
Iav = 2DT/ [1.3·BV·Zth]
EAS (AR) = PD (ave)·tav
www.irf.com
AUIRF1405ZS/L
D.U.T
Driver Gate Drive
ƒ
+
‚
-
„
*
D.U.T. ISD Waveform
Reverse
Recovery
Current
+

RG
V DD
• dv/dt controlled by RG
• Driver same type as D.U.T.
• I SD controlled by Duty Factor "D"
• D.U.T. - Device Under Test
P.W.
Period
VGS=10V
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
-
D=
Period
P.W.
+
+
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
-
Body Diode
VDD
Forward Drop
Inductor Curent
Ripple ≤ 5%
*
ISD
VGS = 5V for Logic Level Devices
Fig 17. Peak Diode Recovery dv/dt Test Circuit for N-Channel
HEXFET® Power MOSFETs
V DS
V GS
RG
RD
D.U.T.
+
-V DD
10V
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
Fig 18a. Switching Time Test Circuit
VDS
90%
10%
VGS
td(on)
tr
t d(off)
tf
Fig 18b. Switching Time Waveforms
www.irf.com
9
AUIRF1405ZS/L
D2Pak (TO-263AB) Package Outline
Dimensions are shown in millimeters (inches)
D2Pak (TO-263AB) Part Marking Information
Part Number
AUIRF1405ZS
YWWA
IR Logo
XX
or
Date Code
Y= Year
WW= Work Week
A= Automotive, LeadFree
XX
Lot Code
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
10
www.irf.com
AUIRF1405ZS/L
TO-262 Package Outline
Dimensions are shown in millimeters (inches)
TO-262 Part Marking Information
Part Number
AUIRF1405ZL
YWWA
IR Logo
XX
or
Date Code
Y= Year
WW= Work Week
A= Automotive, LeadFree
XX
Lot Code
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
www.irf.com
11
AUIRF1405ZS/L
D2Pak Tape & Reel Information
Dimensions are shown in millimeters (inches)
TRR
1.60 (.063)
1.50 (.059)
4.10 (.161)
3.90 (.153)
FEED DIRECTION 1.85 (.073)
1.65 (.065)
1.60 (.063)
1.50 (.059)
11.60 (.457)
11.40 (.449)
0.368 (.0145)
0.342 (.0135)
15.42 (.609)
15.22 (.601)
24.30 (.957)
23.90 (.941)
TRL
10.90 (.429)
10.70 (.421)
1.75 (.069)
1.25 (.049)
4.72 (.136)
4.52 (.178)
16.10 (.634)
15.90 (.626)
FEED DIRECTION
13.50 (.532)
12.80 (.504)
27.40 (1.079)
23.90 (.941)
4
330.00
(14.173)
MAX.
NOTES :
1. COMFORMS TO EIA-418.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION MEASURED @ HUB.
4. INCLUDES FLANGE DISTORTION @ OUTER EDGE.
12
60.00 (2.362)
MIN.
30.40 (1.197)
MAX.
26.40 (1.039)
24.40 (.961)
3
4
www.irf.com
AUIRF1405ZS/L
Ordering Information
Base part
AUIRF1405ZL
AUIRF1405ZS
www.irf.com
Package Type
TO-262
D2Pak
Standard Pack
Form
Tube
Tube
Tape and Reel Left
Tape and Reel Right
Complete Part Number
Quantity
50
50
800
800
AUIRF1405ZL
AUIRF1405ZS
AUIRF1405ZSTRL
AUIRF1405ZSTRR
13
AUIRF1405ZS/L
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its
subsidiaries (IR) reserve the right to make corrections, modifications, enhancements, improvements, and
other changes to its products and services at any time and to discontinue any product or services without
notice. Part numbers designated with the “AU” prefix follow automotive industry and / or customer specific
requirements with regards to product discontinuance and process change notification. All products are sold
subject to IR’s terms and conditions of sale supplied at the time of order acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with IR’s standard warranty. Testing and other quality control techniques are used to the extent
IR deems necessary to support this warranty. Except where mandated by government requirements, testing
of all parameters of each product is not necessarily performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible
for their products and applications using IR components. To minimize the risks with customer products and
applications, customers should provide adequate design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive business practice. IR is not responsible
or liable for such altered documentation. Information of third parties may be subject to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for
that product or service voids all express and any implied warranties for the associated IR product or service
and is an unfair and deceptive business practice. IR is not responsible or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical
implant into the body, or in other applications intended to support or sustain life, or in any other application
in which the failure of the IR product could create a situation where personal injury or death may occur. Should
Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer shall
indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product.
IR products are neither designed nor intended for use in military/aerospace applications or environments
unless the IR products are specifically designated by IR as military-grade or “enhanced plastic.” Only
products designated by IR as military-grade meet military specifications. Buyers acknowledge and agree
that any such use of IR products which IR has not designated as military-grade is solely at the Buyer’s risk,
and that they are solely responsible for compliance with all legal and regulatory requirements in connection
with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless
the specific IR products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part
number including the designation “AU”. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, IR will not be responsible for any failure to meet such requirements.
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
233 Kansas St., El Segundo, California 90245
Tel: (310) 252-7105
14
www.irf.com
Similar pages