FAIRCHILD NC7WBD3125L8X

Revised December 2005
NC7WBD3125
2-Bit Low Power Bus Switch with Level Shifting
General Description
The NC7WBD3125 is a 2-bit ultra high-speed CMOS FET bus
switch with enhanced level shifting circuitry and with TTL-compatible active LOW control inputs. The low On Resistance of the
switch allows inputs to be connected to outputs with minimal
propagation delay and without generating additional ground
bounce noise. The device is organized as a 2-bit switch with
independent bus enable (OE) controls. When OE is LOW, the
switch is ON and Port A is connected to Port B. When OE is
HIGH, the switch is OPEN and a high-impedance state exists
between the two ports. Reduced voltage drive to the gate of the
FET switch permits nominal level shifting of 5V to 3V through
the switch. Control inputs tolerate voltages up to 5.5V independent of VCC.
Features
O Space saving US8 surface mount package
O MicroPak¥ Pb-Free leadless package
O Typical 3: switch resistance at 5.0V VCC, VIN
O Level shift facilitates 5V to 3.3V interfacing
O Minimal propagation delay through the switch
O Power down high impedance input/output
O Zero bounce in flow through mode
O TTL compatible active LOW control inputs
O Control inputs are overvoltage tolerant
O Bus switch replacement for x125 logic part
0V
Ordering Code:
Order
Number
Package
Package Code
Number Top Mark
NC7WBD3125K8X
MAB08A
WB5D
NC7WBD3125L8X
(Preliminary)
MAC08A
T9
Package Description
Supplied As
8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide 3k Units on Tape and Reel
Pb-Free 8-Lead MicroPak, 1.6 mm Wide
5k Units on Tape and Reel
Pb-Free package per JEDEC J-STD-020B.
MicroPak¥ is a trademark of Fairchild Semiconductor Corporation.
© 2005 Fairchild Semiconductor Corporation
DS500374
www.fairchildsemi.com
NC7WBD3125 2-Bit Low Power Bus Switch with Level Shifting
May 2000
NC7WBD3125
Logic Diagram
Connection Diagrams
Pin Assignments for US8
Pin Descriptions
(Top View)
Pin Name
Description
A
Bus A Switch I/O
B
Bus B Switch I/O
OE
Bus Enable Input
Pin One Orientation Diagram
Function Table
Bus Enable Input
(OE)
Function
L
B Connected to A
H
Disconnected
AAA represents Product Code Top Mark - see ordering code
Note: Orientation of Top Mark determines Pin One location. Read the top product
code mark left to right, Pin One is the lower left pin (see diagram).
Pad Assignments for MicroPak
H HIGH Logic Level
L LOW Logic Level
(Top Through View)
www.fairchildsemi.com
2
Recommended Operating
Conditions (Note 3)
0.5V to 7.0V
0.5V to 7.0V
0.5V to 7.0V
Supply Voltage (VCC)
DC Switch Voltage (VS)
DC Output Voltage (VIN) (Note 2)
DC Input Diode Current
(IIK) VIN 0V
Supply Operating (VCC)
50 mA
DC Output (IOUT) Current
(ICC/IGND)
Storage Temperature Range (TSTG)
Junction Temperature under Bias (TJ)
0V to 5.5V
0V to 5.5V
40qC to 85qC
Operating Temperature (TA)
Input Rise and Fall Time (tr, tf)
r100 mA
65qC to 150qC
150qC
Lead Temperature (TL)
0V to 5.5V
Switch Input Voltage (VIN)
Switch Output Voltage (VOUT)
128 mA
DC VCC or Ground Current
4.5V to 5.5V
Control Input Voltage (VIN)
Control Input
0 ns/V to 5 ns/V
Switch I/O
0 ns/V to DC
Thermal Resistance (TJA)
250qC/W
260qC
(Soldering, 10 Seconds)
Power Dissipation (PD) @ 85qC
250 mW
Note 1: The “Absolute Maximum Ratings” are those values beyond which the safety
of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not
guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation.
Note 2: The input and output negative voltage ratings may be exceeded if the input
and output diode current ratings are observed.
Note 3: Unused logic inputs must be held HIGH or LOW. They may not float.
DC Electrical Characteristics
Symbol
Parameter
VCC
(V)
TA
Min
40qC to 85qC
Typ
Units
1.2
Clamp Diode Voltage
VIH
HIGH Level Input Voltage
4.5 to 5.5
VIL
LOW Level Input Voltage
4.5 to 5.5
VOH
HIGH Level Output Voltage
4.5 to 5.5
IIN
Input Leakage Current
5.5
IOFF
Power OFF Leakage Current
5.5
RON
Switch On Resistance
4.5
3.0
7.0
(Note 4)
4.5
3.0
7.0
4.5
15.0
50.0
ICC
Quiescent Supply Current
4.5
2.0
Increase in ICC per Input
(Note 5)
V
IIN
18 mA
V
0.8
V
r1.0
r1.0
PA
PA
See Figure 3
V
:
5.5
1.1
' ICC
Conditions
Max
VIK
5.5
1.0
1.5
mA
10.0
PA
2.5
mA
VIN
VCC
0 d VIN d 5.5V
0 d A, B d VCC
VIN
0V, IIN
64 mA
VIN
0V, IIN
30 mA
VIN
2.4V, IIN
VIN
VCC or GND, IOUT
OE1
OE1
VIN
15 mA
OE2
GND
OE2
VCC
0
3.4V, One OE Input only,
Other OE
VCC
Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the
voltages on the two (A or B) pins.
Note 5: Per TTL driven input (VIN
3.4V, control input only). A and B pins do not contribute to ICC.
3
www.fairchildsemi.com
NC7WBD3125
Absolute Maximum Ratings(Note 1)
NC7WBD3125
AC Electrical Characteristics
TA
Symbol
VCC
Parameter
CL
(V)
tPHL,
Propagation Delay Bus-to-Bus
tPLH
(Note 6)
tPZL,
Output Enable Time
40qC to 85qC,
50 pF, RU
Min
RD
Typ
4.5 to 5.5
4.5 to 5.5
1.0
500:
Units
Output Disable Time
4.5 to 5.5
0.25
ns
VI
OPEN
Figures
1, 2
5.8
ns
VI
7V for tPZL
VI
0V for tPZH
Figures
1, 2
VI
7V for tPLZ
VI
0V for tPHZ
3.5
0.8
Figure
Number
tPZH
tPLZ,
Conditions
Max
3.0
4.8
ns
tPHZ
Figures
1Figure 2
Note 6: This parameter is guaranteed. The bus switch contributes no propagation delay other than the RC delay of the typical On Resistance of the switch and the 50 pF load
capacitance, when driven by an ideal voltage source (zero output impedance). The specified limit is calculated on this basis.
Capacitance
Symbol
Parameter
Typ
CIN
Control Pin Input Capacitance
CI/O (OFF)
Port OFF Capacitance
6.0
CI/O (ON)
Port ON Capacitance
12.0
Max
Units
2.5
pF
Conditions
VCC
0V
pF
VCC
5.0V
pF
VCC
5.0V, OE
AC Loading and Waveforms
Input driven by 50: source terminated in 50:
CL includes load and stray capacitance
Input PRR
1.0 MHz; tW
FIGURE 1. AC Test Circuit
FIGURE 2. AC Waveforms
www.fairchildsemi.com
4
500 ns
OE
0V
NC7WBD3125
DC Electrical Characteristics
FIGURE 3. Typical High Level Output Voltage vs. Supply Voltage
5
www.fairchildsemi.com
NC7WBD3125
Tape and Reel Specification
TAPE FORMAT for US8
Package
Designator
K8X
Tape
Section
Number
Cavities
Cavity
Status
Cover Tape
Status
Leader (Start End)
125 (typ)
Empty
Sealed
Carrier
250
Filled
Sealed
Trailer (Hub End)
75 (typ)
Empty
Sealed
Tape
Section
Number
Cavities
Cavity
Status
Cover Tape
Status
Leader (Start End)
125 (typ)
Empty
Sealed
Carrier
250
Filled
Sealed
Trailer (Hub End)
75 (typ)
Empty
Sealed
TAPE DIMENSIONS inches (millimeters)
TAPE FORMAT for MicroPak
Package
Designator
L8X
TAPE DIMENSIONS inches (millimeters)
www.fairchildsemi.com
6
NC7WBD3125
REEL DIMENSIONS inches (millimeters)
Tape Size
8 mm
A
B
C
D
N
7.0
0.059
0.512
0.795
2.165
(177.8)
(1.50)
(13.00)
(20.20)
(55.00)
7
W1
W2
(8.40 1.50/0.00)
(14.40)
0.331 0.059/0.000
0.567
W3
W1 0.078/0.039
(W1 2.00/1.00)
www.fairchildsemi.com
NC7WBD3125
Physical Dimensions inches (millimeters) unless otherwise noted
8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide
Package Number MAB08A
www.fairchildsemi.com
8
NC7WBD3125
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Pb-Free 8-Lead MicroPak, 1.6 mm Wide
Package Number MAC08A
9
www.fairchildsemi.com
NC7WBD3125 2-Bit Low Power Bus Switch with Level Shifting
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY
PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY
ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT
CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION
As used herein:
provided in the labeling, can be reasonably expected to
result in significant injury to the user.
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
2. A critical component is any component of a life support
(b) support or sustain life, or (c) whose failure to perform
device or system whose failure to perform can be reasonwhen properly used in accordance with instructions for use
ably expected to cause the failure of the life support device
or system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of terms
Datasheet Identification Product Status
Definition
Advance Information
Formative or In Design
This datasheet contains the design specifications for product development. Specifications may change in any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data, and supplementary data will
be published at a later date. Fairchild Semiconductor reserves the right
to make changes at any time without notice in order to improve design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild Semiconductor
reserves the right to make changes at any time without notice in order
to improve design.
Obsolete
Not In Production
This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only.
www.fairchildsemi.com
10