TI1 DAC7632VFR 16-bit, dual voltage output Datasheet

DAC7632
DAC
763
2
SBAS234A – FEBRUARY 2002 – REVISED APRIL 2008
www.ti.com
16-Bit, Dual Voltage Output
DIGITAL-TO-ANALOG CONVERTER
FEATURES
DESCRIPTION
●
●
●
●
The DAC7632 is a 16-bit, dual channel, voltage output,
Digital-to-Analog Converter (DAC) which provides 15-bit
monotonic performance over the specified temperature range.
The device accepts 24-bit serial input data, has doublebuffered DAC input logic (allowing simultaneous update of
both DACs), and provides a serial data output for daisychaining multiple devices. A programmable asynchronous
reset clears all registers to a mid-scale code of 8000H or to
a zero-scale code of 0000H. The DAC7632 can operate from
a single +5V supply or from +5V and –5V supplies, providing
an output range of 0V to +2.5V or –2.5V to +2.5V, respectively.
LOW POWER: 4mW
UNIPOLAR OR BIPOLAR OPERATION
SETTLING TIME: 10µs to ±0.003% FSR
15-BIT LINEARITY AND MONOTONICITY:
–40°C to +85°C
● PROGRAMMABLE RESET TO MID-SCALE
OR ZERO-SCALE
● DOUBLE-BUFFERED DATA INPUTS
APPLICATIONS
Low power and small size per DAC make the DAC7632
ideal for industrial process control, data acquisition systems, and closed-loop servo-control. The DAC7632 is available in an LQFP-32 package and specified over a –40°C to
+85°C temperature range.
● PROCESS CONTROL
● CLOSED-LOOP SERVO-CONTROL
● MOTOR CONTROL
● DATA ACQUISITION SYSTEMS
● DAC-PER-PIN PROGRAMMERS
VDD
VSS
VREFL
Sense
VCC
VREFL
VREFH
VREFH
Sense
DAC7632
SDI
Shift
Register
Input
Register A
DAC
Register A
DAC A
SDO
VOUTA
VOUTA Sense
CS
CLK
RST
RSTSEL
Input
Register B
DAC
Register B
Control
Logic
DAC B
VOUTB
VOUTB Sense
LDAC
LOAD
AGND
DGND
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright © 2002-2008, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ABSOLUTE MAXIMUM RATINGS(1)
VCC and VDD to VSS .............................................................. –0.3V to 11V
VCC and VDD to GND ........................................................... –0.3V to 5.5V
VREFL to VSS ............................................................. –0.3V to (VCC – VSS)
VCC to VREFH ............................................................ –0.3V to (VCC – VSS)
VREFH to VREFL ......................................................... –0.3V to (VCC – VSS)
Digital Input Voltage to GND ................................... –0.3V to VDD + 0.3V
Digital Output Voltage to GND ................................. –0.3V to VDD + 0.3V
Maximum Junction Temperature ................................................... +150°C
Operating Temperature Range ........................................ –40°C to +85°C
Storage Temperature Range ......................................... –65°C to +125°C
Lead Temperature (soldering, 10s) ............................................... +300°C
NOTE: (1) Stresses above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. Exposure to absolute maximum
conditions for extended periods may affect device reliability.
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
PACKAGE/ORDERING INFORMATION(1)
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
DAC7632VFT
DAC7632VFR
Tape and Reel, 250
Tape and Reel, 1000
DAC7632VFB T
DAC7632VFB R
Tape and Reel, 250
Tape and Reel, 1000
MONOTONICITY
PACKAGE-LEAD
PACKAGE
DESIGNATOR
DAC7632VF
14 Bits
LQFP-32
VF
–40°C to +85°C
DAC7632
"
"
"
"
"
"
DAC7632VFB
15 Bits
LQFP-32
VF
–40°C to +85°C
DAC7632B
"
"
"
"
"
"
PRODUCT
NOTE: (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com.
2
DAC7632
www.ti.com
SBAS234A
ELECTRICAL CHARACTERISTICS: Dual Supply
At TA = TMIN to TMAX, VDD = VCC = +5V, VSS = –5V, VREFH = +2.5V, and VREFL = –2.5V, unless otherwise noted.
DAC7632VF
PARAMETER
ACCURACY
Linearity Error
Linearity Match
Differential Linearity Error
Monotonicity, TMIN to TMAX
Bipolar Zero Error
Bipolar Zero Error Drift
Full-Scale Error
Full-Scale Error Drift
Bipolar Zero Matching
Full-Scale Matching
Power-Supply Rejection Ratio (PSRR)
ANALOG OUTPUT
Voltage Output
Output Current
Maximum Load Capacitance
Short-Circuit Current
Short-Circuit Duration
CONDITIONS
MIN
POWER SUPPLY
VDD
VCC
VSS
ICC
IDD
ISS
Power
TEMPERATURE RANGE
Specified Performance
MAX
±3
±4
±2
±4
RL = 10kΩ
VREFL
–1.25
No Oscillation
MIN
±3
±3
10
±3
10
±3
±3
100
VREFH
+1.25
VREFL + 1.25
–2.5
+2.5
VREFH – 1.25
8
0.5
2
60
40
f = 10kHz
7FFFH to 8000H or 8000H to 7FFFH
UNITS
±2
±2
±1
±3
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
LSB
LSB
LSB
Bits
mV
ppm/°C
mV
ppm/°C
mV
mV
ppm/V
✻
✻
✻
✻
✻
✻
✻
10
+4.75
+4.75
–5.25
–1.2
–40
V
mA
pF
mA
✻
✻
V
V
µA
µA
✻
µs
LSB
nV-s
nV/√Hz
nV-s
✻
0.3 • VDD
±10
±10
3.6
✻
✻
✻
✻
0.7 • VDD
IOH = –0.8mA
IOL = 1.6mA
±2
✻
✻
✻
500
–500
To ±0.003%, 5V Output Step
MAX
✻
✻
500
–10, +30
Indefinite
GND or VCC or VSS
TYP
15
±1
5
±1
5
±1
±1
10
Channel-to-Channel Matching
Channel-to-Channel Matching
At Full Scale
DIGITAL INPUT
VIH
VIL
IIH
IIL
DIGITAL OUTPUT
VOH
VOL
TYP
14
REFERENCE INPUT
Ref High Input Voltage Range
Ref Low Input Voltage Range
Ref High Input Current
Ref Low Input Current
DYNAMIC PERFORMANCE
Settling Time
Channel-to-Channel Crosstalk
Digital Feedthrough
Output Noise Voltage
DAC Glitch
DAC7632VFB
4.5
0.3
+5.0
+5.0
–5.0
0.7
50
–0.8
7.5
✻
0.4
+5.25
+5.25
–4.75
1.1
✻
✻
✻
✻
11.5
+85
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
V
V
µA
µA
✻
V
V
✻
✻
✻
✻
✻
V
V
V
mA
µA
mA
mW
✻
°C
✻ Specifications same as DAC7632VF.
DAC7632
SBAS234A
www.ti.com
3
ELECTRICAL CHARACTERISTICS: Single Supply
At TA = TMIN to TMAX, VDD = VCC = +5V, VSS = 0V, VREFH = +2.5V, and VREFL = 0V, unless otherwise noted.
DAC7632VF
PARAMETER
ACCURACY
Linearity Error(1)
Linearity Match
Differential Linearity Error
Monotonicity, TMIN to TMAX
Zero Scale Error
Zero Scale Error Drift
Full-Scale Error
Full-Scale Error Drift
Zero Scale Matching
Full-Scale Matching
Power Supply Rejection Ratio (PSRR)
ANALOG OUTPUT
Voltage Output
Output Current
Maximum Load Capacitance
Short-Circuit Current
Short-Circuit Duration
CONDITIONS
MIN
POWER SUPPLY
VDD
VCC
VSS
ICC
IDD
Power
TEMPERATURE RANGE
Specified Performance
MAX
±3
±4
±2
±4
RL = 10kΩ
0
–1.25
No Oscillation
MIN
±3
±3
10
±3
10
±3
±3
100
VREFH
+1.25
VREFL + 1.25
–2.5
+2.5
VREFH – 1.25
8
0.5
2
60
40
7FFFH to 8000H or 8000H to 7FFFH
UNITS
±2
±2
±1
±3
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
LSB
LSB
LSB
Bits
mV
ppm/°C
mV
ppm/°C
mV
mV
ppm/V
✻
✻
✻
✻
✻
✻
✻
10
+4.75
+4.75
0
–40
V
mA
pF
mA
✻
✻
V
V
µA
µA
✻
µs
LSB
nV-s
nV/√Hz
nV-s
✻
0.3 • VDD
±10
±10
3.6
✻
✻
✻
✻
0.7 • VDD
IOH = –0.8mA
IOL = 1.6mA
±2
✻
✻
✻
250
–250
To ±0.003%, 5V Output Step
MAX
✻
✻
500
–10, +30
Indefinite
GND or VCC
TYP
15
±1
5
±1
5
±1
±1
10
Channel-to-Channel Matching
Channel-to-Channel Matching
At Full Scale
DIGITAL INPUT
VIH
VIL
IIH
IIL
DIGITAL OUTPUT
VOH
VOL
TYP
14
REFERENCE INPUT
Ref High Input Voltage Range
Ref Low Input Voltage Range
Ref High Input Current
Ref Low Input Current
DYNAMIC PERFORMANCE
Settling Time
Channel-to-Channel Crosstalk
Digital Feedthrough
Output Noise Voltage, f = 10kHz
DAC Glitch
DAC7632VFB
4.5
0.3
+5.0
+5.0
0
0.5
50
2.5
✻
0.4
+5.25
+5.25
0
0.9
✻
✻
✻
4.5
+85
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
V
V
µA
µA
✻
V
V
✻
✻
✻
✻
✻
V
V
V
mA
µA
mW
✻
°C
✻ Specifications same as DAC7632VF.
NOTE: (1) If VSS = 0V, the specification applies to Code 0040H and above due to possible negative zero-scale error.
4
DAC7632
www.ti.com
SBAS234A
PIN CONFIGURATION
25 VOUTB
26 VOUTB Sense
27 VREFH Sense
28 VREFH
29 VREFL
30 VREFL Sense
31 VOUTA Sense
SSOP
32 VOUTA
Top View
VCC
1
24
VSS
AGND
2
23
LOAD
AGND
3
22
LDAC
NC
4
21
RST
DAC7632
CLK
NC
16
17
15
8
NC
SDO
14
SDI
NC
18
13
7
NC
VDD
12
CS
NC
19
11
6
NC
DGND
10
RSTSEL
NC
20
9
5
NC
DGND
NC = No Connection
PIN DESCRIPTIONS
PIN
NAME
DESCRIPTION
PIN
NAME
DESCRIPTION
Analog +5V Power Supply
22
LDAC
DAC Register Load Control, Rising Edge
Triggered
LOAD
DAC Input Register Load Control, Active LOW
1
VCC
2, 3
AGND
Analog Ground
4
NC
No Connection
23
5, 6
DGND
Digital Ground
24
VSS
7
VDD
Digital +5V Power Supply
25
VOUTB
8
SDO
Serial Data Output
26
VOUTB Sense
9-16
NC
No Connection
DAC B Output Amplifier Inverting Input. Used to
close the feedback loop at the load.
17
CLK
Data Clock Input
27
VREFH Sense
DAC A and B Reference High Sense Input
18
SDI
Serial Data Input
28
VREFH
DAC A and B Reference High Input
19
CS
Chip Select, Active LOW
29
RSTSEL
VREFL
DAC A and B Reference Low Input
20
30
VREFL Sense
DAC A and B Reference Low Sense Input
31
VREFA Sense
DAC A Output Amplifier Inverting Input. Used to
close the feedback loop at the load.
32
VOUTA
21
RST
Reset Select. Determines the action of RST. If
HIGH, a RST common will set the DAC registers
to mid-scale code (8000H). If LOW, a RST
command will set the DAC registers to zero-scale
code (0000H).
Reset, Rising Edge Triggered. Depending on the
state of RSTSEL, the DAC registers are set to
either mid-scale code or zero-scale code.
DAC7632
SBAS234A
www.ti.com
Analog –5V Power Supply (or 0V for Single Supply)
DAC B Output Voltage
DAC A Output Voltage
5
TYPICAL CHARACTERISTICS: VSS = 0V
At TA = +25°C, VDD = VCC = +5V, VSS = 0V, VREFH = +2.5V, VREFL = 0V, representative unit, unless otherwise specified.
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
LE (LSB)
Digital Input Code
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, +85°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC B, +85°C)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
DLE (LSB)
LE (LSB)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
Digital Input Code
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, –40°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC B, –40°C)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
6
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
Digital Input Code
LE (LSB)
LE (LSB)
DLE (LSB)
DLE (LSB)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
–40°C
LE (LSB)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC B, +25°C)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
+85°C
DLE (LSB)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, +25°C)
DLE (LSB)
DLE (LSB)
LE (LSB)
+25°C
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
DAC7632
www.ti.com
SBAS234A
TYPICAL CHARACTERISTICS: VSS = 0V (Cont.)
At TA = +25°C, VDD = VCC = +5V, VSS = 0V, VREFH = +2.5V, VREFL = 0V, representative unit, unless otherwise specified.
ZERO-SCALE ERROR vs TEMPERATURE
FULL-SCALE ERROR vs TEMPERATURE
3
3
Code (0040H)
Code (FFFFH)
2
Full-Scale Error (mV)
Zero-Scale Error (mV)
2
1
DAC B
0
–1
DAC A
DAC B
0
–1
DAC A
–2
–2
–3
–3
–40
–15
10
35
60
–40
85
–15
35
Temperature (°C)
VREFH CURRENT vs CODE
(all DACs sent to indicated code)
VREFL CURRENT vs CODE
(all DACs sent to indicated code)
0.30
0.00
0.25
–0.05
0.20
0.15
0.10
60
85
–0.10
–0.15
–0.20
0.05
–0.25
0.00
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
–0.30
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
Digital Input Code
ANALOG SUPPLY CURRENT vs TEMPERATURE
ANALOG SUPPLY CURRENT vs DIGITAL INPUT CODE
1
1.0
Data = FFFFH (all DACs)
No Load
No Load
0.8
0.8
0.6
0.6
ICC (mA)
ICC (mA)
10
Temperature (°C)
VREF Current (mA)
VREF Current (mA)
1
0.4
0.2
All DACs
0.4
0.2
0
–40
–15
10
35
60
0.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
85
Temperature (°C)
Digital Input Code
DAC7632
SBAS234A
www.ti.com
7
TYPICAL CHARACTERISTICS: VSS = 0V (Cont.)
At TA = +25°C, VDD = VCC = +5V, VSS = 0V, VREFH = +2.5V, VREFL = 0V, representative unit, unless otherwise specified.
OUTPUT VOLTAGE vs SETTLING TIME
(+2.5V to 2mV)
OUTPUT VOLTAGE vs SETTLING TIME
(0V to +2.5V)
+5V
LDAC
0
Small-Signal Settling
Time: 500µV/div
Output Voltage
Output Voltage
Large-Signal Settling Time: 1V/div
Small-Signal Settling Time: 500µV/div
Large-Signal Settling Time: 1V/div
+5V
LDAC
0
Time (2µs/div)
Time (2µs/div)
OUTPUT VOLTAGE
vs MID-SCALE GLITCH PERFORMANCE
OUTPUT VOLTAGE
vs MID-SCALE GLITCH PERFORMANCE
+5V
LDAC
0
Output Voltage (20mV/div)
Output Voltage (20mV/div)
+5V
LDAC
0
7FFFH to 8000H
8000H to 7FFFH
Time (1µs/div)
Time (1µs/div)
BROADBAND NOISE
OUTPUT NOISE VOLTAGE vs FREQUENCY
Noise (nV/√Hz)
Noise Voltage (50µV/div)
1000
100
BW = 10kHz
Code = 8000H
10
Time (10µs/div)
10
100
1000
10000
100000
1000000
Frequency (Hz)
8
DAC7632
www.ti.com
SBAS234A
TYPICAL CHARACTERISTICS: VSS = 0V (Cont.)
At TA = +25°C, VDD = VCC = +5V, VSS = 0V, VREFH = +2.5V, VREFL = 0V, representative unit, unless otherwise specified.
LOGIC SUPPLY CURRENT
vs LOGIC INPUT LEVEL FOR DIGITAL INPUTS
VOUT vs RLOAD
5
Typical of One
Digital Input
0.40
4
0.30
3
VOUT (V)
Logic Supply Current (mA)
0.50
0.20
Source
2
0.10
1
0.00
0
0.01
0
1
2
3
4
5
Logic Input Level for Digital Inputs (V)
Sink
0.1
1
10
100
RLOAD (kΩ)
VSS = –5V
At TA = +25°C, VDD = VCC = +5V, VSS = –5V, VREFH = +2.5V, VREFL = –2.5V, representative unit, unless otherwise specified.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC B, +25°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, +25°C)
LE (LSB)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
DLE (LSB)
DLE (LSB)
LE (LSB)
+25°C
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
Digital Input Code
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, +85°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC B, +85°C)
LE (LSB)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
DLE (LSB)
DLE (LSB)
LE (LSB)
+85°C
Digital Input Code
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
DAC7632
SBAS234A
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
www.ti.com
9
TYPICAL CHARACTERISTICS: VSS = –5V (Cont.)
At TA = +25°C, VDD = VCC = +5V, VSS = –5V, VREFH = +2.5V, VREFL = –2.5V, representative unit, unless otherwise specified.
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
LE (LSB)
LE (LSB)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
DLE (LSB)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
Digital Input Code
VREFH CURRENT vs CODE
(all DACs sent to indicated code)
VREFL CURRENT vs CODE
(all DACs sent to indicated code)
+0.6
0.0
+0.5
–0.1
VREF Current (mA)
VREF Current (mA)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC B, –40°C)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, –40°C)
DLE (LSB)
–40°C
+0.4
+0.3
+0.2
+0.1
–0.2
–0.3
–0.4
–0.5
0.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
–0.6
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
Digital Input Code
BIPOLAR ZERO ERROR vs TEMPERATURE
POSITIVE FULL-SCALE ERROR vs TEMPERATURE
3
3
Code (FFFFH)
Positive Full-Scale Error (mV)
Code (8000H)
Bipolar Zero Error (mV)
2
1
DAC B
0
–1
DAC A
–2
1
DAC B
0
–1
DAC A
–2
–3
–3
–40
–15
10
35
60
–40
85
–15
10
35
60
85
Temperature (°C)
Temperature (°C)
10
2
DAC7632
www.ti.com
SBAS234A
TYPICAL CHARACTERISTICS: VSS = –5V (Cont.)
At TA = +25°C, VDD = VCC = +5V, VSS = –5V, VREFH = +2.5V, VREFL = –2.5V, representative unit, unless otherwise specified.
NEGATIVE FULL-SCALE ERROR vs TEMPERATURE
ANALOG SUPPLY CURRENT vs DIGITAL INPUT CODE
3
1.00
Analog Supply Current (mA)
Negative Full-Scale Error (mV)
Code (0000H)
2
1
DAC B
0
–1
DAC A
–2
No Load
ICC
0.75
0.50
0.25
0.00
–0.25
–0.50
–0.75
ISS
–1.00
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
–3
–40
–15
10
35
60
85
Temperature (°C)
Digital Input Code
VOUT vs RLOAD
ANALOG SUPPLY CURRENT vs TEMPERATURE
1
5
ICC
Analog Supply Current (mA)
4
Source
3
VOUT (V)
2
1
0
–1
Sink
–2
–3
0.5
0
–0.5
ISS
–1
Data = FFFFH (all DACs)
No Load
–4
–5
0.01
–1.5
0.1
1
10
–40
100
–15
10
35
60
RLOAD (kΩ)
Temperature (°C)
OUTPUT VOLTAGE vs SETTLING TIME
(–2.5V to +2.5V)
OUTPUT VOLTAGE vs SETTLING TIME
(+2.5V to –2.5V)
85
+5V
LDAC
0
Output Voltage
Output Voltage
Large-Signal Settling Time: 2V/div
Small-Signal Settling Time: 500µV/div
Small-Signal Settling Time:
500µV/div
Large-Signal Settling Time: 2V/div
+5V
LDAC
0
Time (2µs/div)
Time (2µs/div)
DAC7632
SBAS234A
www.ti.com
11
TYPICAL CHARACTERISTICS: VSS = –5V (Cont.)
At TA = +25°C, VDD = VCC = +5V, VSS = –5V, VREFH = +2.5V, VREFL = –2.5V, representative unit, unless otherwise specified.
OUTPUT VOLTAGE
vs MID-SCALE GLITCH PERFORMANCE
Output Voltage (50mV/div)
Output Voltage (50mV/div)
OUTPUT VOLTAGE
vs MID-SCALE GLITCH PERFORMANCE
7FFFH to 8000H
8000H to 7FFFH
+5V
LDAC
0
+5V
LDAC
0
Time (1µs/div)
Time (1µs/div)
THEORY OF OPERATION
The digital input is a 24-bit serial word that contains an
address bit for selecting one of two DACs, a quick load bit,
six unused bits, and the 16-bit DAC code (MSB first). The
converters can be powered from either a single +5V supply
or a dual ±5V supply. The device offers a reset function
which immediately sets all DAC output voltages, DAC registers and input registers to mid-scale (code 8000H) or to zeroscale (code 0000H), depending on the state of RSTSEL. See
Figures 2 and 3 for the basic configurations of the DAC7632.
The DAC7632 is a dual channel, voltage output, 16-bit DAC.
The architecture is an R-2R ladder configuration with the
three MSB’s segmented, followed by an operational amplifier
that serves as a buffer. Each DAC has its own R-2R ladder
network, segmented MSBs, and output op amp, as shown in
Figure 1. The minimum voltage output (zero-scale) and
maximum voltage output (full-scale) are set by the external
voltage references VREFL and VREFH, respectively.
RF
VOUT Sense
VOUT
R
2R
2R
2R
2R
2R
2R
2R
2R
2R
VREFH
VREFH Sense
VREFL
VREFL Sense
FIGURE 1. DAC7632 Architecture.
12
DAC7632
www.ti.com
SBAS234A
0V to +2.5V
32
+2.5V
31
1
+5V
1µF
0.1µF
2
3
4
5
1µF
0.1µF
6
7
+5V
8
30
29
VREFL
Sense
VOUTA
28
0V to +2.5V
27
VOUTA
Sense
26
VREFH
Sense
VREFL
25
VOUTB
Sense
VREFH
VOUTB
VCC
VSS
AGND
LOAD
AGND
LDAC
DAC7632
NC
RST
DGND
RSTSEL
DGND
CS
VDD
SDI
CLK
SDO
24
23
LOAD INPUT REGISTER(S)
22
LOAD DAC REGISTERS
21
RESET INPUT AND DAC REGISTERS
20
19
CHIP SELECT
18
SERIAL DATA IN
17
CLOCK
NC NC NC NC NC NC NC NC
9
10 11 12 13 14 15 16
NC = No Connection
FIGURE 2. Basic Single-Supply Operation of the DAC7632.
–2.5V to
+2.5V
32
–2.5V
31
1
+5V
2
1µF
0.1µF
3
4
5
6
1µF
0.1µF
7
+5V
8
NC = No Connection.
30
29
VOUTA
Sense
28
27
VREFH
VREFL
Sense
VOUTA
–2.5V to
+2.5V
+2.5V
VREFH
Sense
VREFL
26
25
VOUTB
Sense
VOUTB
1µF
VSS
VCC
AGND
LOAD
AGND
LDAC
DAC7632
NC
DGND
RST
RSTSEL
DGND
CS
VDD
SDI
CLK
SDO
0.1µF
24
–5V
23
22
21
LOAD INPUT REGISTER(S)
LOAD DAC REGISTERS
RESET INPUT AND DAC REGISTERS
20
+5V
19
18
17
CHIP SELECT
SERIAL DATA IN
CLOCK
NC NC NC NC NC NC NC NC
9
10 11 12 13 14 15 16
FIGURE 3. Basic Dual-Supply Operation of the DAC7632.
DAC7632
SBAS234A
www.ti.com
13
ANALOG OUTPUTS
When VSS = –5V (dual-supply operation), the output amplifier
can swing to within 2.25V of the supply rails over the –40°C
to +85°C temperature range. When VSS = 0V (single-supply
operation), and with RLOAD also connected to ground, the
output can swing to ground. Care must also be taken when
measuring the zero-scale error when VSS = 0V. Since the
output cannot swing below ground, the output voltage may
not change for the first few digital input codes (0000H, 0001H,
0002H, etc.) if the output amplifier has a negative offset. At
the negative limit of –2mV, the first specified output starts at
code 0040H.
Due to the high accuracy of these DACs, system design
problems such as grounding and contact resistance become
very important. A 16-bit converter with a 2.5V full-scale range
has a 1LSB value of 38µV. With a load current of 1mA, series
wiring and connector resistance of only 40mΩ (RW2) will
cause a voltage drop of 40µV, as shown in Figure 4. To
understand what this means in terms of a system layout, the
resistivity of a typical 1 ounce copper-clad printed circuit
board is 1/2mΩ per square. For a 1mA load, a 10 milli-inch
wide printed circuit conductor 600 milli-inches long will result
in a voltage drop of 30µV.
The DAC7632 offers a force and sense output configuration
for the high open-loop gain output amplifier. This feature
allows the loop around the output amplifier to be closed at the
load, as shown in Figure 4, thus ensuring an accurate output
voltage.
REFERENCE INPUTS
The reference inputs, VREFL and VREFH, can be any voltage
between VSS + 2.5V and VCC – 2.5V, provided that VREFH is
at least 1.25V greater than VREFL. The minimum output of
each DAC is equal to VREFL plus a small offset voltage
(essentially, the offset of the output op amp). The maximum
output is equal to VREFH plus a similar offset voltage. Note
RW2
DAC7632
VOUTA
32
VOUTA Sense
31
VREFL Sense
30
VREFL
29
VREFH
28
VREFH Sense
27
VOUTB Sense
26
VOUTB
25
RW1
VOUT
+V
+2.5V
RW1
VOUT
RW2
FIGURE 4. Analog Output Closed-Loop Configuration
RW represents wiring resistances.
that VSS (the negative power supply) must either be
connected to ground or must be in the range of –4.75V to
–5.25V. The voltage on VSS sets several bias points within
the converter. If VSS is not in one of these two configurations,
the bias values may be in error and proper operation of the
device may be affected.
The current into the VREFH input and out of VREFL depends
on the DAC output voltages, and can vary from a few
microamps to approximately 0.5mA. The reference input
appears as a varying load to the reference supply. If the
reference applied can sink or source the required current, a
reference buffer is not required. The DAC7632 features
reference drive and sense connections such that the internal
errors caused by the changing reference current and the
circuit impedances can be minimized. Figures 5 through 13
show different reference configurations and the effect on the
integral linearity and differential linearity, for each case.
+V
DAC7632
VOUTA
32
VOUTA Sense
31
VREFL Sense
30
VREFL
29
VREFH
28
VREFH Sense
27
VOUTB Sense
26
VOUTB
25
OPA2234
VOUT
100Ω
–2.5V
2200pF
1000pF
–V
+V
1000pF
100Ω
+2.5V
2200pF
VOUT
–V
FIGURE 5. Dual Supply Configuration-Buffered References, used for Dual-Supply Performance.
14
DAC7632
www.ti.com
SBAS234A
+V
DAC7632
VOUTA
32
VOUTA Sense
31
VREFL Sense
30
VREFL
29
VREFH
28
OPA2350
VOUT
100Ω
27
VOUTB Sense
26
VOUTB
25
2kΩ
1000pF
+0.050V
98kΩ
+V
100Ω
1000pF
VREFH Sense
2200pF
+2.5V
2200pF
VOUT
FIGURE 6. Single-Supply Buffered Reference with a Reference Low of 50mV.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, +25°C)
LE (LSB)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
DLE (LSB)
DLE (LSB)
LE (LSB)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, +25°C)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
Digital Input Code
FIGURE 7. Integral Linearity and Differential Linearity Error
Characteristic Curves for Figure 6.
FIGURE 8. Integral Linearity and Differential Linearity Error
Characteristic Curves for Figure 9.
+V
+V
DAC7632
VOUTA
32
VOUTA Sense
31
VREFL Sense
30
VREFL
29
VREFH
28
OPA2350
VOUT
100Ω
1000pF
+V
1000pF
VREFH Sense
27
VOUTB Sense
26
VOUTB
25
+1.25V
2200pF
100Ω
2200pF
+2.5V
VOUT
FIGURE 9. Single-Supply Buffered Reference with VREFL = +1.25V and VREFH = +2.5V.
DAC7632
SBAS234A
www.ti.com
15
VOUTA
32
VOUTA Sense
31
VREFL Sense
30
VREFL
29
VREFH
28
DAC7632
VOUT
+V
OPA2350
+V
100Ω
1000pF
VREFH Sense
27
VOUTB Sense
26
VOUTB
25
+2.5V
2200pF
VOUT
FIGURE 10. Single-Supply Buffered VREFH.
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, +25°C)
LE (LSB)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
DLE (LSB)
DLE (LSB)
LE (LSB)
LINEARITY ERROR AND
DIFFERENTIAL LINEARITY ERROR vs CODE
(DAC A, +25°C)
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
0000H 2000H 4000H 6000H 8000H A000H C000H E000H FFFFH
Digital Input Code
Digital Input Code
FIGURE 11. Linearity and Differential Linearity Error Characteristic Curves for Figure 10.
FIGURE 13. Linearity and Differential Linearity Error Characteristic Curves for Figure 12.
DIGITAL INTERFACE
DAC7632
VOUTA
32
VOUTA Sense
31
VREFL Sense
30
VREFL
29
VREFH
28
VREFH Sense
27
VOUTB Sense
26
VOUTB
25
VOUT
+V
+2.5V
VOUT
FIGURE 12. Low-Cost Single-Supply Configuration.
16
See Table I for the basic control logic for the DAC7632. The
interface consists of a Serial Data Clock (CLK) input, Serial
Data Input (SDI), Input Register Load Control Signal (LOAD),
and DAC Register Load Control Signal (LDAC). In addition, a
Chip Select (CS ) input is available to enable serial communication when there are multiple serial devices attached to a
single serial bus. An asynchronous Reset (RST) input (rising
edge triggered) is provided to simplify start-up conditions,
periodic resets, or emergency resets to a known state, depending on the status of the Reset Select (RSTSEL) signal.
The DAC code, quick load control, and address are provided
via a 24-bit serial interface (see Figure 15). The first bit
(DACSEL) selects the input register that will be updated
when LOAD goes LOW. The third bit is a “Quick Load” bit
such that if HIGH, the code in the shift register is loaded into
both input registers when the LOAD signal goes LOW. If the
“Quick Load” bit is LOW when an active LOAD signal is
issued, the content of the shift register is loaded only to the
input register that is addressed by DACSEL. The “Quick
Load” bit is followed by five unused bits. The last 16 bits
(MSB first) make up the DAC code.
DAC7632
www.ti.com
SBAS234A
SERIAL DATA INPUT
B23
DACSEL
B22
B21
B20
B19
B18
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
X
QUICK
LOAD
X
X
X
X
X
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
DACSEL
CS
RST
RSTSEL
LDAC
LOAD
INPUT
REGISTER
DAC
REGISTER
MODE
DAC
0
1
X
X
X
X
L
L
H
H
X
X
H
H
H
H
↑
↑
X
X
X
X
L
H
X
X
↑
H
X
X
L
L
H
H
X
X
Write
Write
Hold
Hold
Reset to 0000H
Reset to 8000H
Hold
Hold
Write
Hold
Reset to 0000H
Reset to 8000H
Write Input
Write Input
Update
Hold
Reset to Zero-Scale
Reset to Mid-scale
A
B
All
All
All
All
TABLE I. DAC7632 Logic Truth Table.
Data presented to SDI is clocked into the shift register on
each rising CLK edge. This data is latched into the input
register(s) via a logic-low level on LOAD. The data is directed
from the shift register to the desired input register(s) specified
by data bits 21 and 23. The internal DAC registers are edge
triggered and not level triggered. When the LDAC signal is
transitioned from LOW to HIGH, the digital word currently in
the input registers are latched. This double-buffered architecture has been designed so that new data can be entered for
each DAC without disturbing the analog outputs. When the
new data has been entered into the device, both DAC
outputs can be updated simultaneously by the rising edge of
LDAC. Additionally, it allows the input registers to be written
to at any point, then the DAC output voltages can be
synchronously changed via a trigger signal (LDAC).
Note that CS and CLK are combined with an OR gate, which
controls the serial-to-parallel shift register. These two inputs
are completely interchangeable. In addition, care must be
taken with the state of CLK when CS rises at the end of a
serial transfer. If CLK is LOW when CS rises, the OR gate
will provide a rising edge to the shift register, shifting the
internal data one additional bit. The result will be incorrect
data and possible selection of the wrong input register(s). If
both CS and CLK are used, CS should rise only when CLK
is HIGH. If not, then either CS or CLK can be used to operate
the shift register (the remaining pin should be tied to DGND).
Please refer to Table II for more information.
DAC7632
SCK
CLK
DIN
SDI
CS
CS
CS(1)
CLK(1)
H(2)
X(3)
H
H
No Change
L(4)
L
H
H
No Change
SERIAL SHIFT REGISTER
L
↑(5)
H
H
Advanced One Bit
L
H
H
Advanced One Bit
H(6)
X
L(7)
H
No Change
H(6)
X
H
↑(8)
No Change
NOTES: (1) CS and CLK are interchangeable. (2) H = Logic HIGH.
(3) X = Don’t Care. (4) L = Logic LOW. (5) = Positive Logic Transition.
(6) A HIGH value is suggested in order to avoid a “false clock” from
advancing the shift register and changing the shift register. (7) If data is
clocked into the serial register while LOAD is LOW, the input registers will
change as data flows through the shift register. This will corrupt the data
in each DAC register that has been erroneously selected. (8) Rising edge
of RST causes no change in the contents of the serial shift register.
TABLE II. Serial Shift Register Truth Table.
SERIAL-DATA OUTPUT
The Serial-Data Output pin (SDO) is the internal shift register’s
output. For the DAC7632, SDO is a driven output and does
not require an external pull-up. Any number of DAC7632s
can be daisy-chained by connecting the SDO pin of one
device to the SDI pin of the following device in the chain, as
shown in Figure 14.
DAC7632
SDI
RST
↑
CLK
SDO
LOAD
DAC7632
CLK
SDO
CS
SDI
CS
SDO
To
Other
Serial
Devices
FIGURE 14. Daisy-Chaining Multiple DAC7632s.
DAC7632
SBAS234A
www.ti.com
17
DIGITAL TIMING
DIGITALLY-PROGRAMMABLE CURRENT SOURCE
Figure 15 and Table III provide detailed timing for the digital
interface of the DAC7632.
The DAC7632 offers a unique set of features that allows a
wide range of flexibility in designing application circuits such
as programmable current sources. The DAC7632 offers both
a differential reference input, as well as an open-loop configuration around the output amplifier. The open-loop configuration around the output amplifier allows a transistor to be
placed within the loop to implement a digitally-programmable, unidirectional current source. The availability of a
differential reference allows programmability for both the fullscale and zero-scale currents. The output current is calculated as:
DIGITAL INPUT CODING
The DAC7632 input data is in Straight Binary format. The
output voltage is given by Equation 1.
VOUT = VREFL +
(VREFH – VREFL) • N
65, 536
where N is the digital input code. This equation does not
include the effects of offset (zero-scale) or gain (full-scale)
errors.
  V H – VREFL   N  
IOUT =   REF
 •  65, 536  
R SENSE



+ (VREFL / R SENSE )
(LSB)
(MSB)
SDI
X
DACSEL
QUICK
LOAD
X
X
X
X
X
D15
D1
D0
CLK
tcss
tCSH
tLD1
tLD2
CS
tLDDD
LOAD
tLDRW
LDAC
tDS
tDH
SDI
tSDO
tCL
tCH
CLK
SDO
tLDDL
tLDDH
LDAC
tS
VOUT
tS
±0.003% FSR
ERROR BAND
tRSTL
±0.003% FSR
ERROR BAND
tRSTH
RST
tRSSH
tRSSS
RSTSEL
FIGURE 15. Digital Input and Output Timing.
18
DAC7632
www.ti.com
SBAS234A
SYMBOL
DESCRIPTION
MIN
tDS
tDH
tCH
tCL
tCSS
tCSH
tLD1
tLD2
Data Valid to CLK Rising
Data Held Valid after CLK Rises
CLK HIGH
CLK LOW
CS LOW to CLK Rising
CLK HIGH to CS Rising
LOAD HIGH to CLK Rising
CLK Rising to LOAD LOW
LOAD LOW Time
LDAC LOW Time
LDAC HIGH Time
LOAD LOW to LDAC Rising
RESETSEL Valid to RESET HIGH
RESET HIGH to RESETSEL Not Valid
RESET LOW Time
RESET HIGH Time
SDO Propagation Delay
Settling Time
10
20
25
25
15
0
10
30
30
100
100
40
0
100
10
10
10
tLDRW
tLDDL
tLDDH
tLDDD
tRSSS
tRSSH
tRSTL
tRSTH
tSDO
tS
MAX
UNITS
30
10
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
TABLE III. Timing Specifications (TA = –40°C to +85°C).
Figure 16 shows a DAC7632 in a 4-20mA current output
configuration. The output current can be determined by
Equation 3:
At full-scale, the output current is 16mA, plus the 4mA, for the
zero current. At zero scale the output current is the offset
current of 4mA (0.5V/125Ω).
  2.5V – 0.5V   N    0.5V 
IOUT =  
+
 •

  65, 536    125Ω 
125Ω

IOUT
VPROGRAMMED
125Ω
DAC7632
VOUTA
32
VOUTA Sense
31
VREFL Sense
30
VREFL
29
VREFH
28
OPA2350
100Ω
27
VOUTB Sense
26
VOUTB
25
2200pF
20kΩ
1000pF
80kΩ
100Ω
1000pF
VREFH Sense
+V
2200pF
+V
+2.5V
IOUT
VPROGRAMMED
125Ω
FIGURE 16. 4-20mA Digitally-Controlled Current Source.
DAC7632
SBAS234A
www.ti.com
19
Revision History
DATE
4/08
REVISION
A
PAGE
SECTION
—
Entire Data Sheet
4
Electrical Characteristics
13
Figures 2, 3
DESCRIPTION
Updated document format.
Changed section title from "Dual Supply" to "Single Supply" (typo).
Updated text in figures to correct names (typo).
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
20
DAC7632
www.ti.com
SBAS234A
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
DAC7632VFBT
ACTIVE
LQFP
VF
32
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7632
B
DAC7632VFBTG4
ACTIVE
LQFP
VF
32
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7632
B
DAC7632VFR
ACTIVE
LQFP
VF
32
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7632
DAC7632VFRG4
ACTIVE
LQFP
VF
32
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7632
DAC7632VFT
ACTIVE
LQFP
VF
32
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7632
DAC7632VFTG4
ACTIVE
LQFP
VF
32
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7632
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jun-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DAC7632VFBT
LQFP
VF
32
250
330.0
16.4
9.6
9.6
1.9
12.0
16.0
Q2
DAC7632VFR
LQFP
VF
32
1000
330.0
16.4
9.6
9.6
1.9
12.0
16.0
Q2
DAC7632VFT
LQFP
VF
32
250
330.0
16.4
9.6
9.6
1.9
12.0
16.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jun-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC7632VFBT
LQFP
VF
DAC7632VFR
LQFP
VF
32
250
367.0
367.0
38.0
32
1000
367.0
367.0
38.0
DAC7632VFT
LQFP
VF
32
250
367.0
367.0
38.0
Pack Materials-Page 2
MECHANICAL DATA
MTQF002B – JANUARY 1995 – REVISED MAY 2000
VF (S-PQFP-G32)
PLASTIC QUAD FLATPACK
0,45
0,25
0,80
24
0,20 M
17
25
16
32
9
0,13 NOM
1
8
5,60 TYP
7,20
SQ
6,80
9,20
SQ
8,80
Gage Plane
0,05 MIN
0,25
0°– 7°
1,45
1,35
Seating Plane
0,75
0,45
0,10
1,60 MAX
4040172/D 04/00
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages