Maxim MAX1080BEUP 300ksps/400ksps, single-supply, low-power, 8-channel, serial 10-bit adcs with internal reference Datasheet

19-1685; Rev 0; 5/00
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
The 4-wire serial interface connects directly to
SPI™/QSPI™ and MICROWIRE™ devices without external
logic. A serial strobe output allows direct connection to
TMS320-family digital signal processors. The MAX1080/
MAX1081 use an external serial-interface clock to perform
successive-approximation analog-to-digital conversions.
The devices feature an internal +2.5V reference and a reference-buffer amplifier with a ±1.5% voltage-adjustment
range. An external reference with a 1V to VDD1 range may
also be used.
The MAX1080/MAX1081 provide a hard-wired SHDN pin
and four software-selectable power modes (normal operation, reduced power (REDP), fast power-down (FASTPD),
and full power-down (FULLPD)). These devices can be
programmed to automatically shut down at the end of a
conversion or to operate with reduced power. When using
the power-down modes, accessing the serial interface
automatically powers up the devices, and the quick turnon time allows them to be shut down between all conversions. This technique can cut supply current below 100mA
at lower sampling rates.
The MAX1080/MAX1081 are available in a 20-pin TSSOP
package. These devices are higher-speed versions of the
MAX148/MAX149. For more information, refer to the
respective data sheet.
Applications
Portable Data Logging
Data Acquisition
Medical Instruments
Battery-Powered Instruments
Features
♦ 8-Channel Single-Ended or 4-Channel
Pseudo-Differential Inputs
♦ Internal Multiplexer and Track/Hold
♦ Single-Supply Operation
+4.5V to +5.5V (MAX1080)
+2.7V to +3.6V (MAX1081)
♦ Internal +2.5V Reference
♦ 400ksps Sampling Rate (MAX1080)
♦ Low Power: 2.5mA (400ksps)
1.3mA (REDP)
0.9mA (FASTPD)
2µA (FULLPD)
♦ SPI/QSPI/MICROWIRE/TMS320-Compatible 4-Wire
Serial Interface
♦ Software-Configurable Unipolar or Bipolar Inputs
♦ 20-Pin TSSOP Package
Ordering Information
PART
TEMP.
RANGE
PINPACKAGE
INL
(LSB)
MAX1080ACUP
0°C to +70°C
20 TSSOP
±1/2
MAX1080BCUP
MAX1080AEUP
0°C to +70°C
-40°C to +85°C
20 TSSOP
20 TSSOP
±1
±1/2
Ordering Information continued at end of data sheet.
Pin Configuration
TOP VIEW
CH0 1
20 VDD1
CH1 2
19 VDD2
18 SCLK
CH2 3
CH3 4
CH4 5
MAX1080
MAX1081
17
CS
16 DIN
Pen Digitizers
CH5 6
15 SSTRB
Process Control
CH6 7
14 DOUT
CH7 8
13 GND
COM 9
12 REFADJ
Typical Operating Circuit appears at end of data sheet.
11 REF
SHDN 10
SPI and QSPI are trademarks of Motorola, Inc.
TSSOP
MICROWIRE is a trademark of National Semiconductor Corp.
________________________________________________________________ Maxim Integrated Products
1
For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
MAX1080/MAX1081
General Description
The MAX1080/MAX1081 10-bit analog-to-digital converters (ADCs) combine an 8-channel analog-input multiplexer, high-bandwidth track/hold (T/H), and serial interface
with high conversion speed and low power consumption.
The MAX1080 operates from a single +4.5V to +5.5V supply; the MAX1081 operates from a single +2.7V to +3.6V
supply. Both devices’ analog inputs are software configurable for unipolar/bipolar and single-ended/pseudo-differential operation.
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
ABSOLUTE MAXIMUM RATINGS
VDD_ to GND .............................................................. -0.3V to 6V
VDD1 to VDD2 ......................................................... -0.3V to 0.3V
CH0–CH7, COM to GND.......................... -0.3V to (VDD1 + 0.3V)
REF, REFADJ to GND .............................. -0.3V to (VDD1 + 0.3V)
Digital Inputs to GND................................................. -0.3V to 6V
Digital Outputs to GND ............................ -0.3V to (VDD2 + 0.3V)
Digital Output Sink Current .................................................25mA
Continuous Power Dissipation (TA = +70°C)
20-Pin TSSOP (derate 7.0mW/°C above +70°C) ........ 559mW
Operating Temperature Ranges
MAX108_ _CUP ................................................. 0°C to +70°C
MAX108_ _EUP............................................... -40°C to +85°C
Storage Temperature Range ............................ -60°C to +150°C
Lead Temperature (soldering, 10s) ................................ +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—MAX1080
(VDD1 = VDD2 = +4.5V to +5.5V, COM = GND, fSCLK = 6.4MHz, 50% duty cycle, 16 clocks/conversion cycle (400ksps), external
+2.5V at REF, REFADJ = VDD1, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DC ACCURACY (Note 1)
10
Resolution
Relative Accuracy (Note 2)
INL
Differential Nonlinearity
DNL
Bits
MAX1080A
±0.5
MAX1080B
±1.0
No missing codes over temperature
LSB
±1.0
LSB
Offset Error
±3.0
LSB
Gain Error (Note 3)
±3.0
LSB
Gain-Error Temperature
Coefficient
±0.8
ppm/°C
Channel-to-Channel Offset-Error
Matching
±0.1
LSB
DYNAMIC SPECIFICATIONS (100kHz sine-wave input, 2.5Vp-p, 400ksps, 6.4MHz clock, bipolar input mode)
Signal-to-Noise plus Distortion
Ratio
SINAD
Total Harmonic Distortion
THD
Spurious-Free Dynamic Range
SFDR
Up to the 5th harmonic
60
dB
-70
dB
70
dB
fIN1 = 99kHz, fIN2 =102kHz
76
dB
Channel-to-Channel Crosstalk
(Note 4)
fIN = 200kHz, VIN = 2.5Vp-p
-78
dB
Full-Power Bandwidth
-3dB point
6
MHz
Full-Linear Bandwidth
SINAD > 58dB
350
kHz
Intermodulation Distortion
IMD
CONVERSION RATE
Conversion Time (Note 5)
tCONV
Track/Hold Acquisition Time
tACQ
2.5
10
Aperture Delay
Duty Cycle
2
fSCLK
ns
ns
<50
Aperture Jitter
Serial Clock Frequency
µs
468
ps
0.5
6.4
MHz
40
60
%
_______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
(VDD1 = VDD2 = +4.5V to +5.5V, COM = GND, fSCLK = 6.4MHz, 50% duty cycle, 16 clocks/conversion cycle (400ksps), external
+2.5V at REF, REFADJ = VDD1, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
ANALOG INPUTS (CH7–CH0, COM)
Input Voltage Range, Single
Ended and Differential (Note 6)
VREF
Unipolar, VCOM = 0
VCH_
Multiplexer Leakage Current
Bipolar, VCOM or VCH_ = VREF/2, referenced
to COM or CH_
±VREF/2
On/off leakage current, VCH_ = 0 or VDD1
±0.001
Input Capacitance
±1
18
V
µA
pF
INTERNAL REFERENCE
REF Output Voltage
VREF
TA = +25°C
2.480
REF Short-Circuit Current
REF Output Temperature
Coefficient
TC VREF
Load Regulation (Note 7)
2.500
V
30
mA
±15
ppm/°C
0.1
0 to 1mA output load
2.520
2.0
mV/mA
Capacitive Bypass at REF
4.7
10
µF
Capacitive Bypass at REFADJ
0.01
10
µF
REFADJ Output Voltage
REFADJ Input Range
For small adjustments, from 1.22V
REFADJ Buffer Disable
Threshold
To power down the internal reference
1.22
V
±100
mV
1.4
VDD1 - 1.0
+2.05
Buffer Voltage Gain
V
V/V
EXTERNAL REFERENCE (reference buffer disabled, reference applied to REF)
REF Input Voltage Range
(Note 8)
1.0
VREF = 2.500V, fSCLK = 6.4MHz
REF Input Current
VDD1 +
50mV
200
VREF = 2.500V, fSCLK = 0
350
320
In power-down mode, fSCLK = 0
V
5
µA
mA
DIGITAL INPUTS (DIN, SCLK, CS, SHDN)
Input High Voltage
VINH
Input Low Voltage
VINL
Input Hysteresis
3.0
VHYST
Input Leakage
IIN
Input Capacitance
CIN
V
0.8
V
±1
µA
0.2
VIN = 0 or VDD2
V
15
pF
DIGITAL OUTPUTS (DOUT, SSTRB)
Output Voltage Low
VOL
ISINK = 5mA
Output Voltage High
VOH
ISOURCE = 1mA
Three-State Leakage Current
Three-State Output Capacitance
IL
CS = 5V
COUT
CS = 5V
0.4
V
±10
µA
4
V
15
pF
_______________________________________________________________________________________
3
MAX1080/MAX1081
ELECTRICAL CHARACTERISTICS—MAX1080 (continued)
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
ELECTRICAL CHARACTERISTICS—MAX1080 (continued)
(VDD1 = VDD2 = +4.5V to +5.5V, COM = GND, fSCLK = 6.4MHz, 50% duty cycle, 16 clocks/conversion cycle (400ksps), external
+2.5V at REF, REFADJ = VDD1, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
5.5
V
POWER SUPPLY
Positive Supply Voltage
(Note 9)
Supply Current
VDD1,
VDD2
IVDD1+
IVDD2
4.5
VDD1 =
VDD2 =
5.5V
Normal operating mode (Note 10)
2.5
4.0
Reduced-power mode (Note 11)
1.3
2.0
Fast power-down mode (Note 11)
0.9
1.5
Full power-down mode (Note 11)
Power-Supply Rejection
PSR
VDD1 = VDD2 = 5V ±10%, midscale input
mA
2
10
µA
±0.5
±2.0
mV
ELECTRICAL CHARACTERISTICS—MAX1081
(VDD1 = VDD2 = +2.7V to +3.6V, COM = GND, fSCLK = 4.8MHz, 50% duty cycle, 16 clocks/conversion cycle (300ksps), external
+2.5V at REF, REFADJ = VDD1, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DC ACCURACY (Note 1)
10
Resolution
Bits
MAX1081A
±0.5
MAX1081B
±1.0
No missing codes over temperature
±1.0
LSB
Offset Error
±3.0
LSB
Gain Error (Note 3)
±3.0
LSB
Relative Accuracy (Note 2)
INL
Differential Nonlinearity
DNL
LSB
Gain-Error Temperature
Coefficient
±1.6
ppm/°C
Channel-to-Channel Offset-Error
Matching
±0.2
LSB
DYNAMIC SPECIFICATIONS (75kHz sine-wave input, 2.5Vp-p, 300ksps, 4.8MHz clock, bipolar input mode)
Signal-to-Noise plus Distortion
Ratio
60
dB
-70
dB
70
dB
fIN1 = 73kHz, fIN2 = 77kHz
76
dB
Channel-to-Channel Crosstalk
(Note 4)
fIN = 150kHz, VIN = 2.5Vp-p
-78
dB
Full-Power Bandwidth
-3dB point
3
MHz
Full-Linear Bandwidth
SINAD > 58dB
250
kHz
SINAD
Total Harmonic Distortion
THD
Spurious-Free Dynamic Range
SFDR
Intermodulation Distortion
4
IMD
Up to the 5th harmonic
_______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
(VDD1 = VDD2 = +2.7V to +3.6V, COM = GND, fSCLK = 4.8MHz, 50% duty cycle, 16 clocks/conversion cycle (300ksps), external
+2.5V at REF, REFADJ = VDD1, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
CONVERSION RATE
Conversion Time (Note 5)
tCONV
Normal operating mode
Track/Hold Acquisition Time
tACQ
Normal operating mode
3.3
µs
625
Aperture Delay
10
Aperture Jitter
<50
Serial Clock Frequency
fSCLK
Normal operating mode
Duty Cycle
ns
ns
ps
0.5
4.8
MHz
40
60
%
ANALOG INPUTS (CH7–CH0, COM)
Input Voltage Range, Single
Ended and Differential (Note 6)
VREF
Unipolar, VCOM = 0
VCH_
Multiplexer Leakage Current
Bipolar, VCOM or VCH_ = VREF/2,
referenced to COM or CH_
±VREF/2
On/off leakage current, VCH_ = 0 or VDD1
±0.001
Input Capacitance
±1
18
V
µA
pF
INTERNAL REFERENCE
REF Output Voltage
VREF
TA = +25°C
2.480
REF Short-Circuit Current
REF Output Temperature
Coefficient
TC VREF
Load Regulation (Note 7)
4.7
Capacitive Bypass at REFADJ
0.01
REFADJ Output Voltage
For small adjustments, from 1.22V
REFADJ Buffer Disable
Threshold
To power down the internal reference
2.520
mA
±15
ppm/°C
2.0
mV/mA
10
µF
10
µF
1.22
V
±100
mV
1.4
VDD1 - 1
+2.05
Buffer Voltage Gain
EXTERNAL
REFERENCE
(reference buffer disabled, reference applied to REF)
Buffer Voltage
Gain
REF Input Voltage Range
(Note 8)
V/V
VDD1 +
50mV
200
V
350
320
VREF = 2.500V, fSCLK = 0
V
V/V
2.05
1.0
VREF = 2.500V, fSCLK = 4.8MHz
REF Input Current
V
15
0.1
0 to 0.75mA output load
Capacitive Bypass at REF
REFADJ Input Range
2.500
µA
5
In power-down mode, fSCLK = 0
DIGITAL INPUTS (DIN, SCLK, CS, SHDN)
Input High Voltage
VINH
Input Low Voltage
VINL
Input Hysteresis
2.0
0.2
VHYST
Input Leakage
IIN
Input Capacitance
CIN
V
0.8
V
±1
VIN = 0 or VDD2
15
V
µA
pF
_______________________________________________________________________________________
5
MAX1080/MAX1081
ELECTRICAL CHARACTERISTICS—MAX1081 (continued)
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
ELECTRICAL CHARACTERISTICS—MAX1081 (continued)
(VDD1 = VDD2 = +2.7V to +3.6V, COM = GND, fSCLK = 4.8MHz, 50% duty cycle, 16 clocks/conversion cycle (300ksps), external
+2.5V at REF, REFADJ = VDD1, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL OUTPUTS (DOUT, SSTRB)
Output Voltage Low
VOL
ISINK = 5mA
Output Voltage High
VOH
ISOURCE = 0.5mA
Three-State Leakage Current
Three-State Output Capacitance
IL
CS = 3V
COUT
CS = 3V
0.4
VDD2 - 0.5V
V
V
±10
15
µA
pF
POWER SUPPLY
Positive Supply Voltage
(Note 9)
Supply Current
VDD1,
VDD2
IVDD1+
IVDD2
2.7
VDD1 =
VDD2 =
3.6V
Normal operating mode (Note 10)
2.5
3.5
Reduced-power mode (Note 11)
1.3
2.0
Fast power-down mode (Note 11)
0.9
1.5
Full power-down mode (Note 11)
Power-Supply Rejection
PSR
3.6
VDD1 = VDD2 = 2.7V to 3.6V, midscale input
V
mA
2
10
µA
±0.5
±2.0
mV
TYP
MAX
UNITS
TIMING CHARACTERISTICS–MAX1080
(Figures 1, 2, 6, 7; VDD1 = VDD2 = +4.5V to +5.5V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
SCLK Period
tCP
156
ns
SCLK Pulse Width High
tCH
62
ns
SCLK Pulse Width Low
tCL
62
ns
DIN to SCLK Setup
tDS
35
ns
DIN to SCLK Hold
tDH
0
ns
CS Fall to SCLK Rise Setup
tCSS
35
ns
SCLK Rise to CS Rise Hold
tCSH
0
ns
SCLK Rise to CS Fall Ignore
tCSO
35
ns
CS Rise to SCLK Rise Ignore
tCS1
SCLK Rise to DOUT Hold
tDOH
CLOAD = 20pF
10
20
ns
SCLK Rise to SSTRB Hold
tSTH
CLOAD = 20pF
10
20
ns
SCLK Rise to DOUT Valid
tDOV
CLOAD = 20pF
80
ns
SCLK Rise to SSTRB Valid
tSTV
CLOAD = 20pF
80
ns
CS Rise to DOUT Disable
tDOD
CLOAD = 20pF
10
65
ns
CS Rise to SSTRB Disable
tSTD
CLOAD = 20pF
10
65
ns
CS Fall to DOUT Enable
tDOE
CLOAD = 20pF
65
ns
CS Fall to SSTRB Enable
tSTE
CLOAD = 20pF
65
ns
CS Pulse Width High
tCSW
6
35
ns
100
_______________________________________________________________________________________
ns
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
(Figures 1, 2, 6, 7; VDD1 = VDD2 = +2.7V to +3.6V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SCLK Period
tCP
208
ns
SCLK Pulse Width High
tCH
83
ns
SCLK Pulse Width Low
tCL
83
ns
DIN to SCLK Setup
tDS
45
ns
DIN to SCLK Hold
tDH
0
ns
CS Fall to SCLK Rise Setup
tCSS
45
ns
SCLK Rise to CS Rise Hold
tCSH
0
ns
SCLK Rise to CS Fall ignore
tCSO
45
ns
CS Rise to SCLK Rise Ignore
tCS1
45
ns
SCLK Rise to DOUT Hold
tDOH
CLOAD = 20pF
13
20
SCLK Rise to SSTRB Hold
tSTH
CLOAD = 20pF
13
20
SCLK Rise to DOUT Valid
tDOV
CLOAD = 20pF
SCLK Rise to SSTRB Valid
tSTV
CLOAD = 20pF
CS Rise to DOUT Disable
tDOD
CLOAD = 20pF
13
CS Rise to SSTRB Disable
tSTD
CLOAD = 20pF
13
CS Fall to DOUT Enable
tDOE
CS Fall to SSTRB Enable
tSTE
CS Pulse Width High
tCSW
ns
ns
100
ns
100
ns
85
ns
85
ns
CLOAD = 20pF
85
ns
CLOAD = 20pF
85
ns
100
ns
Note 1: Tested at VDD1 = VDD2 = VDD(MIN), COM = GND, unipolar single-ended input mode.
Note 2: Relative accuracy is the deviation of the analog value at any code from its theoretical value after the full-scale range has
been calibrated.
Note 3: Offset nulled.
Note 4: Ground the “on” channel; sine wave is applied to all “off” channels.
Note 5: Conversion time is defined as the number of clock cycles multiplied by the clock period; clock has 50% duty cycle.
Note 6: The common-mode range for the analog inputs (CH7–CH0 and COM) is from GND to VDD1.
Note 7: External load should not change during conversion for specified accuracy. Guaranteed specification of 2mV/mA is the
result of production test limitations.
Note 8: ADC performance is limited by the converter’s noise floor, typically 300µVp-p.
Note 9: Electrical characteristics are guaranteed from VDD1(MIN) = VDD2(MIN) to VDD1(MAX) = VDD2(MIN). For operations beyond
this range, see Typical Operating Characteristics. For guaranteed specifications beyond the limits, contact the factory.
Note 10: AIN= midscale. Unipolar mode. MAX1080 tested with 20pF on DOUT, 20pF on SSTRB, and fSCLK = 6.4MHz, 0 to 5V.
MAX1081 tested with same loads, fSCLK = 4.8MHz, 0 to 3V.
Note 11: SCLK = DIN = GND, CS = VDD1.
_______________________________________________________________________________________
7
MAX1080/MAX1081
TIMING CHARACTERISTICS—MAX1081
Typical Operating Characteristics
(MAX1080: VDD1 = VDD2 = 5.0V, fSCLK = 6.4MHz; MAX1081: VDD1 = VDD2 = 3.0V, fSCLK = 4.8MHz; CLOAD = 20pF, 4.7µF capacitor
at REF, 0.01µF capacitor at REFADJ, TA = +25°C, unless otherwise noted.)
DIFFERENTIAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
0.10
SUPPLY CURRENT (mA)
0.08
0.05
DNL (LSB)
0
0
-0.05
2.5
2.0
-0.04
-0.10
-0.15
-0.08
200
0
400
600
800
1000
1200
200
0
600
400
800
1000
1.5
1200
2.5
3.0
3.5
4.0
4.5
5.0
5.5
DIGITAL OUTPUT CODE
DIGITAL OUTPUT CODE
SUPPLY VOLTAGE (V)
SUPPLY CURRENT vs. TEMPERATURE
SUPPLY CURRENT vs. SUPPLY
VOLTAGE (STATIC)
SUPPLY CURRENT vs. TEMPERATURE
(STATIC)
2.8
2.6
2.4
MAX1081
2.2
1.5
MAX1080 (PD1 = 1, PD0 = 1)
2.0
SUPPLY CURRENT (mA)
MAX1080
NORMAL OPERATION (PD1 = PD0 = 1)
2.0
SUPPLY CURRENT (mA)
3.0
2.5
MAX1080/1-05
2.5
MAX1080/1-04
3.2
SUPPLY CURRENT (mA)
3.0
REDP (PD1 = 1, PD0 = 0)
1.0
FASTPD (PD1 = 0, PD0 = 1)
MAX1080/1-06
INL (LSB)
0.04
3.5
MAX1080/1-02
0.15
MAX1080/1-01
0.12
SUPPLY CURRENT vs. SUPPLY
VOLTAGE (CONVERTING)
MAX1080/1-03
INTEGRAL NONLINEARITY
vs. DIGITAL OUTPUT CODE
MAX1081 (PD1 = 1, PD0 = 1)
1.5
MAX1080 (PD1 = 1, PD0 = 0)
MAX1081 (PD1 = 1, PD0 = 0)
1.0
0.5
0.5
0
0
MAX1080 (PD1 = 0, PD0 = 1)
MAX1081 (PD1 = 0, PD0 = 1)
2.0
-20
0
20
40
60
80
100
3.0
3.5
4.0
4.5
5.0
5.5
-20
0
20
40
60
TEMPERATURE (°C)
SHUTDOWN SUPPLY CURRENT
vs. SUPPLY VOLTAGE
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
REFERENCE VOLTAGE
vs. SUPPLY VOLTAGE
1.5
1.0
0.5
1.5
MAX1081
1.0
3.5
4.0
4.5
SUPPLY VOLTAGE (V)
5.0
5.5
5.0
5.5
2.5001
2.4999
2.4995
0
3.0
2.5003
2.4997
0.5
0
100
MAX1080/1-09
MAX1080
2.0
SUPPLY CURRENT (µA)
2.0
(PD1 = PD0 = 0)
80
2.5005
MAX1080/1-08
2.5
MAX1080/1-07
(PD1 = PD0 = 0)
2.5
-40
SUPPLY VOLTAGE (V)
2.5
8
2.5
TEMPERATURE (°C)
REFERENCE VOLTAGE (V)
-40
SUPPLY CURRENT (µA)
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
-40
-20
0
20
40
60
TEMPERATURE (°C)
80
100
2.5
3.0
3.5
4.0
4.5
SUPPLY VOLTAGE (V)
_______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
REFERENCE VOLTAGE vs. TEMPERATURE
2.4994
2.4992
-0.25
-0.50
2.4990
MAX1080/1-12
0
OFFSET ERROR (LSB)
OFFSET ERROR (LSB)
MAX1081
-0.25
-0.50
2.4988
-20
0
20
40
60
80
100
2.7
TEMPERATURE (°C)
3.0
3.3
3.6
-40
-15
VDD (V)
35
60
85
MAX1081
GAIN ERROR vs. TEMPERATURE
MAX1080/1-14
GAIN ERROR vs. SUPPLY VOLTAGE
0.25
10
TEMPERATURE (°C)
MAX1080/1-13
0
0
GAIN ERROR (LSB)
-40
GAIN ERROR (LSB)
REFERENCE VOLTAGE (V)
MAX1080
2.4998
OFFSET ERROR vs. TEMPERATURE
MAX1080/1-11
2.5000
2.4996
OFFSET ERROR vs. SUPPLY VOLTAGE
0
MAX1080/1-10
2.5002
-0.25
-0.25
-0.50
-0.50
-0.75
2.7
3.0
3.3
VDD (V)
3.6
-40
-15
10
35
60
85
TEMPERATURE (°C)
_______________________________________________________________________________________
9
MAX1080/MAX1081
Typical Operating Characteristics (continued)
(MAX1080: VDD1 = VDD2 = 5.0V, fSCLK = 6.4MHz; MAX1081: VDD1 = VDD2 = 3.0V, fSCLK = 4.8MHz; CLOAD = 20pF, 4.7µF capacitor
at REF, 0.01µF capacitor at REFADJ, TA = +25°C, unless otherwise noted.)
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
MAX1080/MAX1081
Pin Description
PIN
NAME
FUNCTION
1–8
CH0–CH7
9
COM
Ground Reference for Analog Inputs. COM sets zero-code voltage in single-ended mode. Must be
stable to ±0.5LSB.
10
SHDN
Active-Low Shutdown Input. Pulling SHDN low shuts down the device, reducing supply current to 2µA
(typ).
Sampling Analog Inputs
11
REF
Reference-Buffer Output/ADC Reference Input. Reference voltage for analog-to-digital conversion.
In internal reference mode, the reference buffer provides a 2.500V nominal output, externally
adjustable at REFADJ. In external reference mode, disable the internal buffer by pulling REFADJ to
VDD1.
12
REFADJ
Input to the Reference-Buffer Amplifier. To disable the reference-buffer amplifier, connect REFADJ to
VDD1.
13
GND
Analog and Digital Ground
14
DOUT
Serial Data Output. Data is clocked out at SCLK’s rising edge. High impedance when CS is high.
15
SSTRB
Serial Strobe Output. SSTRB pulses high for one clock period before the MSB decision. High impedance when CS is high.
16
DIN
Serial Data Input. Data is clocked in at SCLK’s rising edge.
17
CS
Active-Low Chip Select. Data will not be clocked into DIN unless CS is low. When CS is high, DOUT
and SSTRB are high impedance.
18
SCLK
Serial Clock Input. Clocks data in and out of serial interface and sets the conversion speed. (Duty
cycle must be 40% to 60%.)
19
VDD2
Positive Supply Voltage
20
VDD1
Positive Supply Voltage
VDD2
DOUT
DOUT
CLOAD
20pF
6k
GND
b) High-Z to VOL and VOH to VOL
Figure 1. Load Circuits for Enable Time
10
6k
CLOAD
20pF
GND
a) High-Z to VOH and VOL to VOH
VDD2
6k
DOUT
DOUT
CLOAD
20pF
CLOAD
20pF
6k
GND
a) VOH to High-Z
GND
b) VOL to High-Z
Figure 2. Load Circuits for Disable Time
______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
The MAX1080/MAX1081 ADCs use a successiveapproximation conversion technique and input T/H circuitry to convert an analog signal to a 10-bit digital output. A flexible serial interface provides easy interface to
microprocessors (µPs). Figure 3 shows a functional diagram of the MAX1080/MAX1081.
sinusoidal signal at IN-, the input voltage is determined
by:
(
The maximum voltage variation is determined by:
max
Pseudo-Differential Input
The equivalent circuit of Figure 4 shows the MAX1080/
MAX1081s’ input architecture, which is composed of a
T/H, input multiplexer, input comparator, switchedcapacitor DAC, and reference.
In single-ended mode, the positive input (IN+) is connected to the selected input channel and the negative
input (IN-) is set to COM. In differential mode, IN+ and
IN- are selected from the following pairs: CH0/CH1,
CH2/CH3, CH4/CH5, and CH6/CH7. Configure the
channels according to Tables 1 and 2.
The MAX1080/MAX1081 input configuration is pseudodifferential because only the signal at IN+ is sampled.
The return side (IN-) is connected to the sampling
capacitor while converting and must remain stable
within ±0.5LSB (±0.1LSB for best results) with respect
to GND during a conversion.
If a varying signal is applied to the selected IN-, its
amplitude and frequency must be limited to maintain
accuracy. The following equations express the relationship between the maximum signal amplitude and its
frequency to maintain ±0.5LSB accuracy. Assuming a
CS
SCLK
DIN
SHDN
CH0
CH1
CH2
CH3
CH4
CH5
CH6
CH7
COM
10
1
2
3
4
5
6
7
8
dνIN−
1LSB
VREF
= VIN− 2πf ≤
=
10
dt
t CONV 2 t
CONV
(
)
A 2.6Vp-p, 60Hz signal at IN- will generate a ±0.5LSB
error when using a +2.5V reference voltage and a
2.5µs conversion time (15 / f SCLK ). When a DC reference voltage is used at IN-, connect a 0.1µF capacitor
to GND to minimize noise at the input.
During the acquisition interval, the channel selected as
the positive input (IN+) charges capacitor CHOLD. The
acquisition interval spans three SCLK cycles and ends
on the falling SCLK edge after the input control word’s
last bit has been entered. At the end of the acquisition
interval, the T/H switch opens, retaining charge on
C HOLD as a sample of the signal at IN+. The conversion interval begins with the input multiplexer switching
CHOLD from IN+ to IN-. This unbalances node ZERO at
the comparator’s input. The capacitive DAC adjusts
during the remainder of the conversion cycle to restore
node ZERO to VDD1/2 within the limits of 10-bit resolution. This action is equivalent to transferring a
12pF ✕ [(VIN+ - VIN-)] charge from CHOLD to the binaryweighted capacitive DAC, which in turn forms a digital
representation of the analog input signal.
GND
17
18
16
)
νIN− = VIN− sin(2πft)
INPUT
SHIFT
REGISTER
INT
CLOCK
CONTROL
LOGIC
CH0
CH1
OUTPUT
SHIFT
REGISTER
ANALOG
INPUT
MUX
CAPACITIVE
DAC
REF
14
15
DOUT
SSTRB
T/H
CLOCK
IN
10 + 2-BIT
SAR ADC
OUT
REF
9
+1.22V
REFERENCE
REFADJ 12
REF 11
17k
A ≈ 2.05
Figure 3. Functional Diagram
CHOLD
12pF
ZERO
CSWITCH*
HOLD
TRACK
COM
20
VDD1
VDD2
GND
COMPARATOR
RIN
800Ω
6pF
CH7
13
+2.500V
CH4
CH5
CH6
19
MAX1080
MAX1081
CH2
CH3
INPUT
MUX
AT THE SAMPLING INSTANT,
THE MUX INPUT SWITCHES FROM
THE SELECTED IN+ CHANNEL TO
THE SELECTED IN- CHANNEL.
VDD1/2
SINGLE-ENDED MODE: IN+ = CH0–CH7, IN- = COM.
PSEUDO-DIFFERENTIAL MODE: IN+ AND IN- SELECTED FROM
PAIRS OF CH0/CH1, CH2/CH3, CH4/CH5, AND CH6/CH7.
*INCLUDES ALL INPUT PARASITICS
Figure 4. Equivalent Input Circuit
______________________________________________________________________________________
11
MAX1080/MAX1081
Detailed Description
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
Track/Hold
The T/H enters its tracking mode on the falling clock
edge after the fifth bit of the 8-bit control word has been
shifted in. It enters its hold mode on the falling clock
edge after the eighth bit of the control word has been
shifted in. If the converter is set up for single-ended
inputs, IN- is connected to COM and the converter converts the “+” input. If the converter is set up for differential inputs, the difference of [(IN+) - (IN-)] is converted.
At the end of the conversion, the positive input connects back to IN+ and CHOLD charges to the input signal.
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
the acquisition time lengthens, and more time must be
allowed between conversions. The acquisition time,
tACQ, is the maximum time the device takes to acquire
the signal and the minimum time needed for the signal
to be acquired. It is calculated by the following equation:
tACQ = 7 ✕ (RS + RIN) ✕ 12pF
where RIN = 800Ω, RS = the source impedance of the
input signal, and t ACQ is never less than 468ns
(MAX1080) or 625ns (MAX1081). Note that source
impedances below 4kΩ do not significantly affect the
ADC’s AC performance.
Input Bandwidth
The ADC’s input tracking circuitry has a 6MHz
(MAX1080) or 3MHz (MAX1081) small-signal bandwidth, so it is possible to digitize high-speed transient
events and measure periodic signals with bandwidths
exceeding the ADC’s sampling rate by using undersampling techniques. To avoid high-frequency signals
being aliased into the frequency band of interest, antialias filtering is recommended.
Analog Input Protection
Internal protection diodes, which clamp the analog input
to VDD1 and GND, allow the channel input pins to swing
from GND - 0.3V to V DD1 + 0.3V without damage.
However, for accurate conversions near full scale, the
inputs must not exceed VDD1 by more than 50mV or be
lower than GND by 50mV.
If the analog input exceeds 50mV beyond the supplies, do not allow the input current to exceed 2mA.
Table 1. Channel Selection in Single-Ended Mode (SGL/DIF = 1)
SEL2
0
SEL1
0
SEL0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
CH0
+
CH1
CH2
CH3
CH4
CH5
CH6
CH7
COM
–
+
–
+
–
+
–
+
–
+
–
+
–
+
–
Table 2. Channel Selection in Pseudo-Differential Mode (SGL/DIF = 0)
SEL2
SEL1
SEL0
CH0
CH1
0
0
0
+
–
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
12
–
CH2
CH3
+
–
CH4
CH5
+
–
CH6
CH7
+
–
–
+
+
–
+
–
+
______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
MAX1080/MAX1081
OSCILLOSCOPE
MAX1080
MAX1081
0 TO
+2.500V
ANALOG
INPUT 0.01µF
VDD1
VDD2
+3V OR +5V
0.1µF
SCLK
10µF
GND
CH7
SSTRB
COM
CS
REFADJ
0.01µF
SCLK
VDD2
DIN
2.5V
EXTERNAL CLOCK
DOUT*
DOUT
REF
SSTRB
SHDN
4.7µF
VDD2
CH1
CH2
CH3
CH4
*FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $3FF (HEX)
Figure 5. Quick-Look Circuit
Quick Look
To quickly evaluate the MAX1080/MAX1081s’ analog performance, use the circuit of Figure 5. The devices require
a control byte to be written to DIN before each conversion. Connecting DIN to VDD2 feeds in control bytes of
$FF (HEX), which trigger single-ended unipolar conversions on CH7 without powering down between conversions. The SSTRB output pulses high for one clock
period before the MSB of the conversion result is shifted out of DOUT. Varying the analog input to CH7 will
alter the sequence of bits from DOUT. A total of 16
clock cycles is required per conversion. All transitions
of the SSTRB and DOUT outputs typically occur 20ns
after the rising edge of SCLK.
Starting a Conversion
Start a conversion by clocking a control byte into DIN.
With CS low, each rising edge on SCLK clocks a bit from
DIN into the MAX1080/MAX1081s’ internal shift register.
After CS falls, the first arriving logic “1” bit defines the
control byte’s MSB. Until this first “start” bit arrives, any
number of logic “0” bits can be clocked into DIN with no
effect. Table 3 shows the control-byte format.
The MAX1080/MAX1081 are compatible with SPI/
QSPI and MICROWIRE devices. For SPI, select the correct clock polarity and sampling edge in the SPI control
registers: set CPOL = 0 and CPHA = 0. MICROWIRE,
SPI, and QSPI all transmit a byte and receive a byte at
the same time. Using the Typical Operating Circuit, the
simplest software interface requires only three 8-bit
transfers to perform a conversion (one 8-bit transfer to
configure the ADC, and two more 8-bit transfers to clock
out the conversion result). See Figure 17 for MAX1080/
MAX1081 QSPI connections.
Simple Software Interface
Make sure the CPU’s serial interface runs in master
mode so the CPU generates the serial clock. Choose a
clock frequency from 500kHz to 6.4MHz (MAX1080) or
4.8MHz (MAX1081):
1) Set up the control byte and call it TB1. TB1 should
be of the format: 1XXXXXXX binary, where the Xs
denote the particular channel, selected conversion
mode, and power mode.
2) Use a general-purpose I/O line on the CPU to pull
CS low.
3) Transmit TB1 and simultaneously receive a byte
and call it RB1. Ignore RB1.
4) Transmit a byte of all zeros ($00 hex) and simultaneously receive byte RB2.
5) Transmit a byte of all zeros ($00 hex) and simultaneously receive byte RB3.
6) Pull CS high.
______________________________________________________________________________________
13
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
Table 3. Control-Byte Format
BIT 7
(MSB)
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
(LSB)
START
SEL2
SEL1
SEL0
UNI/BIP
SGL/DIF
PD1
PD0
BIT
NAME
DESCRIPTION
7(MSB)
START
The first logic “1” bit after CS goes low defines the beginning of the control byte.
6
5
4
SEL2
SEL1
SEL0
These three bits select which of the eight channels are used for the conversion (Tables 1 and 2).
3
UNI/BIP
1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. In unipolar mode, an
analog input signal from 0 to VREF can be converted; in bipolar mode, the differential signal can
range from -VREF/2 to +VREF/2.
2
SGL/DIF
1 = single ended, 0 = pseudo-differential. Selects single-ended or pseudo-differential conversions. In single-ended mode, input signal voltages are referred to COM. In pseudo-differential
mode, the voltage difference between two channels is measured (Tables 1 and 2).
1
0(LSB)
PD1
PD0
Select operating mode.
PD1
PD0
Mode
0
0
Full power-down
0
1
Fast power-down
1
0
Reduced power
1
1
Normal operation
Figure 6 shows the timing for this sequence. Bytes RB2
and RB3 contain the result of the conversion, padded
with three leading zeros, two sub-LSB bits, and one
trailing zero. The total conversion time is a function of
the serial-clock frequency and the amount of idle time
between 8-bit transfers. To avoid excessive T/H droop,
make sure the total conversion time does not exceed
120µs.
Digital Output
In unipolar input mode, the output is straight binary
(Figure 14). For bipolar input mode, the output is two’s
complement (Figure 15). Data is clocked out on the rising edge of SCLK in MSB-first format.
Serial Clock
The external clock not only shifts data in and out but
also drives the analog-to-digital conversion steps.
SSTRB pulses high for one clock period after the last bit
of the control byte. Successive-approximation bit decisions are made and appear at DOUT on each of the
next 12 SCLK rising edges (Figure 6). SSTRB and
DOUT go into a high-impedance state when CS goes
high; after the next CS falling edge, SSTRB outputs a
logic low. Figure 7 shows the detailed serial-interface
timings.
14
The conversion must complete in 120µs or less, or
droop on the sample-and-hold capacitors may degrade
conversion results.
Data Framing
The falling edge of CS does not start a conversion.
The first logic high clocked into DIN is interpreted as a
start bit and defines the first bit of the control byte. A
conversion starts on SCLK’s falling edge, after the eighth
bit of the control byte (the PD0 bit) is clocked into DIN.
The start bit is defined as follows:
The first high bit clocked into DIN with CS low any
time the converter is idle, e.g., after VDD1 and VDD2
are applied.
OR
The first high bit clocked into DIN after bit 4 of a conversion in progress is clocked onto the DOUT pin.
Once a start bit has been recognized, the current conversion may only be terminated by pulling SHDN low.
The fastest the MAX1080/MAX1081 can run with CS held
low between conversions is 16 clocks per conversion.
Figure 8 shows the serial-interface timing necessary to
perform a conversion every 16 SCLK cycles. If CS is tied
low and SCLK is continuous, guarantee a start bit by first
clocking in 16 zeros.
______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
MAX1080/MAX1081
CS
tACQ
SCLK
1
4
8
9
12
16
20
24
SEL SEL SEL UNI/ SGL/
1 0 BIP DIF PD1 PD0
2
DIN
START
HIGH-Z
SSTRB
HIGH-Z
RB1
RB2
RB3
HIGH-Z
HIGH-Z
B9 B8
B7 B6 B5
B4
B3 B2 B1 B0
S1 S0
DOUT
IDLE
ACQUISITION
CONVERSION
IDLE
Figure 6. Single-Conversion Timing
___________Applications Information
Power-On Reset
When power is first applied, and if SHDN is not pulled
low, internal power-on reset circuitry activates the
MAX1080/MAX1081 in normal operating mode, ready to
convert with SSTRB = low. The MAX1080/MAX1081
require 10µs to reset after the power supplies stabilize;
no conversions should be initiated during this time. If
CS is low, the first logical 1 on DIN is interpreted as a
start bit. Until a conversion takes place, DOUT shifts out
zeros. Additionally, wait for the reference to stabilize
when using the internal reference.
Power Modes
You can save power by placing the converter in one of
two low-current operating modes or in full power-down
between conversions. Select the power mode through
bit 1 and bit 0 of the DIN control byte (Tables 3 and 4),
or force the converter into hardware shutdown by driving SHDN to GND.
The software power-down modes take effect after the
conversion is completed; SHDN overrides any software
power mode and immediately stops any conversion in
progress. In software power-down mode, the serial
interface remains active while waiting for a new control
byte to start conversion and switch to full-power mode.
Once the conversion is completed, the device goes into
the programmed power mode until a new control byte
is written.
The power-up delay is dependent on the power-down
state. Software low-power modes will be able to start
conversion immediately when running at decreased
clock rates (see Power-Down Sequencing). During
power-on reset, when exiting software full power-down
mode, or when exiting hardware shutdown, the device
goes immediately into full-power mode and is ready to
convert after 2µs when using an external reference.
When using the internal reference, wait for the typical
power-up delay from a full power-down (software or
hardware) as shown in Figure 9.
Software Power-Down
Software power-down is activated using bits PD1 and
PD0 of the control byte. When software power-down is
asserted, the ADC completes the conversion in
progress and powers down into the specified low-quiescent-current state (2µA, 0.9mA, or 1.3mA).
The first logic 1 on DIN is interpreted as a start bit and
puts the MAX1080/MAX1081 into its full-power mode.
Following the start bit, the data input word or control
byte also determines the next power-down state. For
example, if the DIN word contains PD1 = 0 and PD0 = 1,
a 0.9mA power-down resumes after one conversion.
Table 4 details the four power modes with the corresponding supply current and operating sections. For
data rates achievable in software power-down modes,
see Power-Down Sequencing.
______________________________________________________________________________________
15
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
CS
tCSW
tCSS
tCP
tCH
tCSO
tCSH
tCS1
tCL
SCLK
tDS
tDH
tDOH
DIN
tDOV
tDOD
tDOE
DOUT
tSTH
tSTV
tSTE
tSTD
SSTRB
Figure 7. Detailed Serial-Interface Timing
Table 4. Software-Controlled Power Modes
TOTAL SUPPLY CURRENT
PD1/PD0
MODE
CIRCUIT SECTIONS*
CONVERTING
(mA)
AFTER
CONVERSION
INPUT COMPARATOR
REFERENCE
00
Full Power-Down
(FULLPD)
2.5
2µA
Off
Off
01
Fast Power-Down
(FASTPD)
2.5
0.9mA
Reduced Power
On
10
Reduced-Power
Mode (REDP)
2.5
1.3mA
Reduced Power
On
11
Normal Operating
2.5
2.0mA
Full Power
On
*Circuit operation between conversions; during conversion all circuits are fully powered up.
Hardware Power-Down
Pulling SHDN low places the converter in hardware
power-down. Unlike software power-down mode, the
conversion is terminated immediately. When returning
to normal operation from SHDN with an external reference, the MAX1080/MAX1081 can be considered fully
powered up within 2µs of actively pulling SHDN high.
When using the internal reference, the conversion
should be initiated only after the reference has settled;
its recovery time is dependent on the external bypass
capacitors and shutdown duration.
Power-Down Sequencing
The MAX1080/MAX1081 automatic power-down modes
can save considerable power when operating at less
than maximum sample rates. Figures 10 and 11 show
16
the average supply current as a function of the sampling rate.
Using Full Power-Down Mode
Full power-down mode (FULLPD) achieves the lowest
power consumption, up to 1000 conversions per channel per second. Figure 10a shows the MAX1081’s
power consumption for one- or eight-channel conversions utilizing full power-down mode (PD1 = PD0 = 0),
with the internal reference and the maximum clock
speed. A 0.01µF bypass capacitor at REFADJ forms an
RC filter with the internal 17kΩ reference resistor, with a
200µs time constant. To achieve full 10-bit accuracy,
seven time constants or 1.4ms are required after
power-up if the bypass capacitor is fully discharged
between conversions. Waiting this 1.4ms duration in
______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
MAX1080/MAX1081
CS
DIN
S CONTROL BYTE 0
1
S CONTROL BYTE 1
8
12
16 1
5
8
S CONTROL BYTE 2
12
16 1
5
8
12
S
ETC.
16 1
5
SCLK
HIGH-Z
DOUT
B9
S0
B4
CONVERSION RESULT 0
B9
B4
S0
CONVERSION RESULT 1
B9
B4
HIGH-Z
SSTRB
Figure 8. Continuous 16-Clock/Conversion Timing
10,000
MAX1081, VDD1 = VDD2 = 3.0V
CLOAD = 20pF
CODE = 1010100000
1.25
SUPPLY CURRENT (µA)
REFERENCE POWER-UP DELAY (ms)
1.50
1.00
0.75
0.50
1000
8 CHANNELS
100
1 CHANNEL
10
0.25
0
0.0001
1
0.001
0.01
0.1
1
1
10
10
Figure 9. Reference Power-Up Delay vs. Time in Shutdown
1k
10k
100k
Figure 10b. Average Supply Current vs. Sampling Rate (sps)
Using FULLPD and External Reference
1000
2.5
MAX1081, VDD1 = VDD2 = 3.0V
CLOAD = 20pF
CODE = 1010100000
NORMAL OPERATION
SUPPLY CURRENT (mA)
SUPPLY CURRENT (µA)
100
SAMPLING RATE (sps)
TIME IN SHUTDOWN (s)
100
8 CHANNELS
10
1 CHANNEL
1
2.0
REDP
FASTPD
1.5
1.0
MAX1081, VDD1= VDD2 = 3.0V
CLOAD = 20pF
CODE = 1010100000
0.5
0.1
1
10
100
1k
10k
SAMPLING RATE (sps)
Figure 10a. Average Supply Current vs. Sampling Rate (sps)
Using FULLPD and Internal Reference
0
50
100
150
200
250
300
350
SAMPLING RATE (sps)
Figure 11. Average Supply Current vs. Sampling Rate (sps) Using
FASTPD, REDP, Normal Operation, and Internal Reference
______________________________________________________________________________________
17
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
fast power-down (FASTPD) or reduced-power (REDP)
mode instead of in full power-up can further reduce
power consumption. This is achieved by using the
sequence shown in Figure 12a.
Figure 10b shows the MAX1081’s power consumption
for one- or eight-channel conversions utilizing FULLPD
mode (PD1 = PD0 = 0), an external reference, and the
maximum clock speed. One dummy conversion to
power up the device is needed, but no wait time is necessary to start the second conversion, thereby achieving lower power consumption at up to half the full
sampling rate.
trolled at the maximum clock speed. The clock speed
in FASTPD or REDP should be limited to 4.8MHz for the
MAX1080/MAX1081. FULLPD mode may provide
increased power savings in applications where the
MAX1080/MAX1081 are inactive for long periods of
time, but intermittent bursts of high-speed conversions
are required. Figure 12b shows FASTPD and REDP timing.
Using Fast Power-Down and Reduced Power Modes
FASTPD and REDP modes achieve the lowest power
consumption at speeds close to the maximum sampling rate. Figure 11 shows the MAX1081’s power consumption in FASTPD mode (PD1 = 0, PD0 = 1), REDP
mode (PD1 = 1, PD0 = 0), and for comparison, normal
operating mode (PD1 = 1, PD0 = 1). The figure shows
power consumption using the specified power-down
mode, with the internal reference and conversion con-
An internal buffer is designed to provide 2.5V at
REF for the MAX1080/MAX1081. The internally trimmed
1.22V reference is buffered with a 2.05V/V gain.
Internal and External References
The MAX1080/MAX1081 can be used with an internal
or external reference. An external reference can be
connected directly at REF or at the REFADJ pin.
Internal Reference
The MAX1080/MAX1081s’ full-scale range with the internal reference is 2.5V with unipolar inputs and ±1.25V
with bipolar inputs. The internal reference voltage is
adjustable by ±100mV with the circuit in Figure 13.
WAIT 1.4ms (7 x RC)
0 0
1
DIN
1 0
1
REDP
FULLPD
1
FULLPD
DUMMY CONVERSION
1.22V
0 0
1
1.22V
REFADJ
0V
γ = RC = 17kΩ x 0.01µF
2.5V
2.5V
REF
0V
2.5mA
IVDD1 + IVDD2
2.5mA
2.5mA
1.3mA OR 0.9mA
0V
0mA
Figure 12a. Full Power-Down Timing
1 0
1
DIN
REF
1 0
1
REDP
REDP
0 1
1
FASTPD
2.5V (ALWAYS ON)
2.5mA
IVDD1 + IVDD2
2.5mA
0.9mA
2.5mA
0.9mA
1.3mA
Figure 12b. FASTPD and REDP Timing
18
______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
MAX1080/MAX1081
+3.3V
OUTPUT CODE
24k
MAX1081
510k
100k
12
011 . . . 111
FS = VREF + VCOM
2
011 . . . 110
ZS = VCOM
REFADJ
-VREF
+ VCOM
2
VREF
1LSB =
1024
-FS =
000 . . . 010
0.01µF
000 . . . 001
000 . . . 000
111 . . . 111
111 . . . 110
Figure 13. MAX1081 Reference-Adjust Circuit
111 . . . 101
OUTPUT CODE
100 . . . 001
100 . . . 000
FULL-SCALE
TRANSITION
11 . . . 111
- FS
11 . . . 110
COM*
+FS - 1LSB
INPUT VOLTAGE (LSB)
11 . . . 101
*VCOM ≤ VREF / 2
FS = VREF + VCOM
ZS = VCOM
V
1LSB = REF
1024
00 . . . 011
00 . . . 010
00 . . . 001
00 . . . 000
0 1
(COM)
2
3
INPUT VOLTAGE (LSB)
FS
FS - 3/2LSB
Figure 15. Bipolar Transfer Function, Full Scale (FS) =
VREF / 2 + VCOM, Zero Scale (ZS) = VCOM
Transfer Function
Table 5 shows the full-scale voltage ranges for unipolar
and bipolar modes. Figure 14 depicts the nominal,
unipolar input/output (I/O) transfer function, and Figure
15 shows the bipolar I/O transfer function. Code transitions occur halfway between successive-integer LSB
values. Output coding is binary, with 1LSB = 2.44mV
for unipolar and bipolar operation.
Layout, Grounding, and Bypassing
Figure 14. Unipolar Transfer Function, Full Scale (FS) = VREF
+ VCOM, Zero Scale (ZS) = VCOM
External Reference
An external reference can be placed at the input
(REFADJ) or the output (REF) of the internal referencebuffer amplifier. The REFADJ input impedance is typically 17kΩ. At REF, the DC input resistance is a
minimum of 18kΩ. During conversion, an external reference at REF must deliver up to 350µA DC load current
and have 10Ω or less output impedance. If the reference has a higher output impedance or is noisy, bypass
it close to the REF pin with a 4.7µF capacitor.
Using the REFADJ input makes buffering the external
reference unnecessary. To use the direct REF input,
disable the internal buffer by connecting REFADJ to
VDD1.
For best performance, use PC boards; wire-wrap boards
are not recommended. Board layout should ensure that
digital and analog signal lines are separated from each
other. Do not run analog and digital (especially clock)
lines parallel to one another, or digital lines underneath
the ADC package.
Figure 16 shows the recommended system ground
connections. Establish a single-point analog ground
(star ground point) at GND. Connect all other analog
grounds to the star ground. Connect the digital system
ground to this ground only at this point. For lowestnoise operation, the ground return to the star ground’s
power supply should be low impedance and as short
as possible.
High-frequency noise in the V DD1 power supply may
affect the high-speed comparator in the ADC. Bypass
the supply to the star ground with 0.1µF and 10µF
capacitors close to pin 20 of the MAX1080/MAX1081.
______________________________________________________________________________________
19
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
Table 5. Full Scale and Zero Scale
UNIPOLAR MODE
BIPOLAR MODE
Full Scale
Zero Scale
Positive
Full Scale
Zero
Scale
Negative
Full Scale
VREF + VCOM
VCOM
VREF / 2
+ VCOM
VCOM
-VREF / 2
+ VCOM
mit clock) as an active-high output clock and CLKR
(TMS320 receive clock) as an active-high input
clock. CLKX and CLKR on the TMS320 are connected to the MAX1080/MAX1081’s SCLK input.
SUPPLIES
VDD1
VDD2
GND
*R = 10Ω
VDD1
GND
COM VDD2
VDD
DGND
DIGITAL
CIRCUITRY
MAX1080
MAX1081
*OPTIONAL
Figure 16. Power-Supply Grounding Connection
Minimize capacitor lead lengths for best supply-noise
rejection. If the power supply is very noisy, a 10Ω resistor can be connected as a lowpass filter (Figure 16).
2) The MAX1080/MAX1081’s CS pin is driven low by
the TMS320’s XF_ I/O port to enable data to be
clocked into the MAX1080/MAX1081s’ DIN pin.
3) An 8-bit word (1XXXXX11) should be written to the
MAX1080/MAX1081 to initiate a conversion and
place the device into normal operating mode. See
Table 3 to select the proper XXXXX bit values for your
specific application.
4) The MAX1080/MAX1081s’ SSTRB output is monitored through the TMS320’s FSR input. A falling
edge on the SSTRB output indicates that the conversion is in progress and data is ready to be
received from the device.
5) The TMS320 reads in 1 data bit on each of the next
16 rising edges of SCLK. These data bits represent
the 10 + 2-bit conversion result followed by 4 trailing
bits, which should be ignored.
6) Pull CS high to disable the MAX1080/MAX1081 until
the next conversion is initiated.
Definitions
High-Speed Digital Interfacing with QSPI
Integral Nonlinearity
The MAX1080/MAX1081 can interface with QSPI using
the circuit in Figure 17 (f SCLK = 4.0MHz, CPOL = 0,
CPHA = 0). This QSPI circuit can be programmed to do a
conversion on each of the eight channels. The result is
stored in memory without taxing the CPU, since QSPI
incorporates its own microsequencer.
Integral nonlinearity (INL) is the deviation of the values
from a straight line on an actual transfer function. This
straight line can be a best-straight-line fit or a line
drawn between the endpoints of the transfer function,
once offset and gain errors have been nullified. The
static linearity parameters for the MAX1080/MAX1081
are measured using the best-straight-line fit method.
TMS320LC3x Interface
Figure 18 shows an application circuit to interface the
MAX1080/MAX1081 to the TMS320 in external clock
mode. Figure 19 shows the timing diagram for this interface circuit.
Use the following steps to initiate a conversion in the
MAX1080/MAX1081 and to read the results:
1) The TMS320 should be configured with CLKX (trans20
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between
an actual step width and the ideal value of 1LSB. A
DNL error specification of less than 1LSB guarantees
no missing codes and a monotonic transfer function.
______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
ANALOG
INPUTS
CH0
VDD1 20
2
CH1
VDD2 19
(POWER SUPPLIES)
3
CH2
SCLK 18
SCK
4
CH3 MAX1080
5
VDD1
+5V
OR
+3V
1
CH4
MAX1081
0.1µF
10µF
CS 17
PCS0
DIN 16
MOSI
6
CH5
SSTRB 15
7
CH6
DOUT 14
8
CH7
GND 13
9
COM
REFADJ 12
10 SHDN
REF 11
MAX1080/MAX1081
+5V
OR
+3V
MC683XX
MISO
4.7µF
0.01µF
(GND)
Figure 17. QSPI Connections
Aperture Jitter
Aperture jitter (tAJ) is the sample-to-sample variation in
the time between the samples.
Aperture Delay
XF
CLKX
Aperture delay (t AD ) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken.
CS
SCLK
TMS320LC3x
MAX1080
MAX1081
CLKR
DX
DIN
DR
DOUT
FSR
SSTRB
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the SNR is the ratio of the full-scale analog
input (RMS value) to the RMS quantization error (residual error). The ideal, theoretical minimum analog-to-digital noise is caused only by quantization error and
results directly from the ADC’s resolution (N bits):
SNR = (6.02
Figure 18. MAX1080/MAX1081-to-TMS320 Serial Interface
Aperture Width
✕
N + 1.76)dB
In reality, there are other noise sources besides quantization noise, including thermal noise, reference noise,
clock jitter, etc. Therefore, SNR is calculated by taking
the ratio of the RMS signal to the RMS noise, which
includes all spectral components minus the fundamental, the first five harmonics, and the DC offset.
Aperture width (tAW) is the time the T/H circuit requires
to disconnect the hold capacitor from the input circuit
(for instance, to turn off the sampling bridge and put
the T/H unit in hold mode).
______________________________________________________________________________________
21
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
CS
SCLK
DIN
SSTRB
START
SEL2
SEL1
SEL0
UNI/BIP SGI/DIF
PD1
PD0
HIGH IMPEDANCE
DOUT
B8
MSB
S1
S0
HIGH IMPEDANCE
Figure 19. MAX1080/MAX1081-to-TMS320 Serial Interface
Signal-to-Noise Plus Distortion (SINAD)
SINAD is the ratio of the fundamental input frequency’s
RMS amplitude to RMS equivalent of all other ADC output signals:
Ordering Information (continued)
TEMP.
RANGE
PART
INL
(LSB)
-40°C to +85°C
20 TSSOP
±1
MAX1081ACUP
0°C to +70°C
20 TSSOP
±1/2
Effective Number of Bits (ENOB)
MAX1081BCUP
0°C to +70°C
20 TSSOP
±1
ENOB indicates the global accuracy of an ADC at a
specific input frequency and sampling rate. An ideal
ADC’s error consists only of quantization noise. With an
input range equal to the ADC’s full-scale range, calculate ENOB as follows:
MAX1081AEUP
MAX1081BEUP
-40°C to +85°C
-40°C to +85°C
20 TSSOP
20 TSSOP
±1/2
±1
SINAD (dB) = 20 ✕ log (SignalRMS / NoiseRMS)
MAX1080BEUP
PINPACKAGE
Typical Operating Circuit
ENOB = (SINAD - 1.76) / 6.02
+5V OR
+3V
Total Harmonic Distortion (THD)
THD is the ratio of the RMS sum of the input signal’s
first five harmonics to the fundamental itself. This is
expressed as:

2
2
2
2
2
 V2 + V3 + V4 + V4 + V5 


THD = 20 × log
V1
where V1 is the fundamental amplitude, and V2 through
V 5 are the amplitudes of the 2nd- through 5th-order
harmonics.
CH0
0 TO
+2.5V
ANALOG
INPUTS
VDD1
VDD
0.1µF
VDD2
MAX1080 GND
MAX1081
CH7
REF
4.7µF
CPU
COM
I/O
CS
SCLK
SCK (SK)
DIN
REFADJ
0.01µF
Spurious-Free Dynamic Range (SFDR)
MOSI (SO)
DOUT
MISO (SI)
SSTRB
SHDN
VDD2
VSS
SFDR is the ratio of the RMS amplitude of the fundamental (maximum signal component) to the RMS value
of the next-largest distortion component.
Chip Information
TRANSISTOR COUNT: 4286
PROCESS: BiCMOS
22
______________________________________________________________________________________
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
TSSOP.EPS
Note: The MAX1080/MAX1081 do not have an exposed die pad.
______________________________________________________________________________________
23
MAX1080/MAX1081
________________________________________________________Package Information
MAX1080/MAX1081
300ksps/400ksps, Single-Supply, Low-Power,
8-Channel, Serial 10-Bit ADCs with Internal Reference
NOTES
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
24 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2000 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Similar pages