Micrel MIC2536-1YM Dual usb power distributibution switch final information Datasheet

MIC2536
Micrel
MIC2536
Dual USB Power Distribution Switch
Final Information
General Description
Features
The MIC2536 is a cost-effective high-side power switch, with
two independently controlled channels, optimized for buspowered Universal Serial Bus (USB) applications. Few external components are necessary to satisfy USB requirements.
Each switch channel of the MIC2536 will supply up to 100mA
as required for USB bus-powered downstream devices. Fault
current is limited to typically 275mA by fast-acting currentlimit circuitry which minimizes voltage droop on the upstream
port during fault conditions. A flag output with transient filter
indicates fault conditions to the local USB controller but will
ignore short flag signals resulting from inrush current during
hot plug-in events.
Soft start eliminates the momentary voltage droop on other
ports that may occur when the switch is enabled in buspowered applications. Additional features include thermal
shutdown to prevent catastrophic switch failure from highcurrent loads and 3.3V and 5V logic compatible enable
inputs.
The MIC2536 is available in active-high and active-low versions in 8-lead SOP and MSOP.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Compliant to USB specifications
2.7V to 5.5V operating range
150mA minimum continuous load current per channel
400mΩ typical on-resistance
Fast-acting short circuit protection with
thermal shutdown
Integrated filter eliminates
false overcurrent flag assertions
Individual open-drain fault flag pins with transient filter
3V/5V-compatible enable inputs
Active-high (-1) and active-low (-2) versions
Reverse-current blocking in off mode (no “body diode”)
Soft-start circuit
100µA maximum on-state supply current
<1µA typical off-state supply current
–40°C to 85°C operation
Applications
•
•
•
•
•
•
•
USB keyboard bus-powered hubs
USB bus-powered docking stations
Note Book PCs
PDAs
General purpose power distribution applications
PC board hot swap
Inrush current-limiting
Typical Application
Ferrite
Beads
10k
4.50V to 5.25V
Upstream VBUS
100mA max.
VBUS
1.5k
D+
D–
GND
4.7µF
VIN
OUT
GND
D+
3.3V USB Controller
MIC5207-3.3
IN
VBUS
10k
1µF
MIC2536-2
ON/OFF
ENA
OUTA
OVERCURRENT
FLGA
IN
OVERCURRENT
FLGB
GND
ENB
OUTB
ON/OFF
.01µF
63µF
D–
USB
Port 1
GND
0.1µF
VBUS
D+
.01µF
63µF
D–
USB
Port 2
GND
Data
Data
(Two Pair)
to USB
Controller
Typical Two-Port Bus-Powered Hub
UL Recognized Component
Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 944-0970 • http://www.micrel.com
March 2000
1
MIC2536
MIC2536
Micrel
Ordering Information
Part Number
Enable
Temperature Range
Package
MIC2536-1BM
Active High
–40°C to +85°C
8-Lead SOP
MIC2536-2BM
Active Low
–40°C to +85°C
8-Lead SOP
MIC2536-1BMM
Active High
–40°C to +85°C
8-Lead MSOP
MIC2536-2BMM
Active Low
–40°C to +85°C
8-Lead MSOP
Pin Configuration
MIC2536-x
ENA
1
8
OUTA
FLGA
2
7
IN
FLGB
3
6
GND
ENB
4
5
OUTB
8-Lead SOP (M)
8-Lead MSOP (MM)
Pin Description
Pin Number
Pin Name
1
ENA
Enable A (Input): Channel A control input. Active high (–1) or active low (–2)
input.
2
FLGA
Flag A: (Output): Channel A open-drain fault flag output. Indicates
overcurrent or thermal shutdown conditions. Overcurrent conditions must
last longer than tD in order to assert FLG.
3
FLGB
Flag B (Output): Channel B open-drain fault flag output. Indicates overcurrent or thermal shutdown conditions. Overcurrent conditions must last
longer than tD in order to assert FLG.
4
ENB
Enable B (Input): Channel B control input. Active high (–1) or active low (–2)
input.
5
OUTB
Output B: Channel B switch output.
6
GND
Ground
7
IN
8
OUTA
MIC2536
Pin Function
Positive Switch and Logic Supply Input
Output A: Channel A switch output.
2
March 2000
MIC2536
Micrel
Absolute Maximum Ratings (Note 1)
Operating Ratings (Note 2)
Supply Voltage (VIN) ..................................................... +6V
Fault Flag Voltage (VFLG) .............................................. +6V
Fault Flag Current (IFLG) ............................................ 25mA
Output Voltage (VOUT) .................................................. +6V
Output Current (IOUT) ............................... Internally Limited
Control Input (VEN) ................................... –0.3V to VIN +2V
Storage Temperature (TS) ....................... –65°C to +150°C
Lead Temperature (Soldering 5 sec.) ....................... 260°C
ESD Rating, Note 3 ...................................................... 1kV
Supply Voltage (VIN) ................................... +2.7V to +5.5V
Ambient Operating Temperature (TA) ........ –40°C to +85°C
Thermal Resistance
SOP (θJA) .......................................................... 160°C/W
MSOP (θJA) ....................................................... 206°C/W
Electrical Characteristics
VIN = +5V; TA = 25°C, bold values indicate –40°C ≤ TA ≤ +85°C; unless noted
Parameter
Condition
Supply Current
Enable Input Threshold
Min
Typ
Max
Units
both switches off, OUTA–B = open, Note 4
0.75
5
µA
both switches on, OUTA–B = open, Note 4
60
100
µA
low-to-high transition, Note 4
1.7
2.4
V
high-to-low transition, Note 4
0.8
1.5
0.01
V
µA
Enable Input Current
VEN = 0V to 5.5V
1
Enable Input Capacitance
Note 5
Switch Resistance
single switch, IOUT = 100mA
400
Output Turn-On Delay, tON
RL = 50Ω, CL = 1µF
1.5
ms
Output Turn-On Rise Time, tR
RL = 50Ω, CL = 1µF
1.4
ms
Output Turnoff Delay, tOFF
RL = 50Ω, CL = 1µF
130
µs
Output Turnoff Fall Time, tF
RL = 50Ω, CL = 1µF
115
µs
Output Leakage Current
each output (switch off)
Current Limit Threshold
ramped load applied to enable output
Short Circuit Current Limit
each output (enabled into load), VOUT = 0V
Current Limit Response
VOUT = 0V to IOUT = ILIMIT (short applied to output), Note 5
Flag Response Delay, tD
VIN = 5V, apply VOUT = 0V until FLG low
1
1
150
275
pF
700
mΩ
10
µA
500
mA
400
mA
µs
10
5
13
20
ms
VIN = 3.3V, apply VOUT = 0V until FLG low
13
ms
Overtemperature Shutdown
TJ increasing, Note 5
135
°C
Threshold
TJ decreasing, Note 5
125
°C
Error Flag Output Resistance
VIN = 5V, IL = 10mA
10
20
Ω
VIN = 3.3V, IL = 10mA
15
30
Ω
0.01
1
µA
Error Flag Off Current
VFLAG = 5V
Note 1.
Exceeding the absolute maximum rating may damage the device.
Note 2.
The device is not guaranteed to function outside its operating rating.
Note 3.
Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF.
Note 4.
Off is ≤ 0.8V and on is ≥ 2.4V for the MIC2536-1. Off is ≥ 2.4V and on is ≤ 0.8V for the MIC2536-2. The enable input has approximately
200mV of hysteresis.
Note 5.
Guaranteed by design. Not production tested.
March 2000
3
MIC2536
MIC2536
Micrel
Test Circuit
VOUT
Device
Under OUT
Test
RL
CL
Functional Characteristics Test Circuit
Timing Diagrams
tr
tf
90%
VOUT
90%
10%
10%
Output Rise and Fall Times
VEN
50%
tOFF
tON
90%
VOUT
10%
Active-High Switch Delay Times (MIC2536-1)
VEN
50%
tOFF
tON
90%
VOUT
10%
Active-Low Switch Delay Times (MIC2536-2)
MIC2536
4
March 2000
MIC2536
Micrel
Supply On Current
vs. Input Voltage
Output On-Resistance
vs. Input Voltage
60
–40°C
85°C
0
2
3
4
5
INPUT VOLTAGE (V)
500
400
3
25°C
–40°C
300
200
0
2
6
118
1.5
0
2
6
–40°C
–40°C
85°C
1.0
0.5
110
0
2
6
Flag Delay vs.
Input Voltage
3
4
5
INPUT VOLTAGE (V)
85°C
2.0
25°C
1.5
1.0 –40°C
0.5
0
2
6
Supply Off Current
vs. Input Voltage
20
1
300
10
–40°C
5
0
2
3
4
5
INPUT VOLTAGE (V)
0.8
0.6
–40°C
0.4
0.2
85°C
25°C
85°C
280 25°C
270
–40°C
260
250
0
2
6
6
290
CURRENT (mA)
SUPPLY CURRENT (µA)
TIME (ms)
25°C
3
4
5
INPUT VOLTAGE (V)
Current Limit Threshold
vs. Input Voltage
85°C
15
6
2.5
25°C
85°C
3
4
5
INPUT VOLTAGE (V)
3
4
5
INPUT VOLTAGE (V)
Control Voltage vs.
Input Voltage VEN Rising
25°C
116
TIME (µs)
TIME (ms)
4
INPUT VOLTAGE (V)
2.0
108
2
2 –40°C
Control Voltage vs.
Input Voltage VEN Falling
120
112
25°C
1
Output Fall Time
vs. Input Voltage
114
85°C
100
THRESHOLD VOLTAGE (V)
20
25°C
600 85°C
TIME (ms)
80
40
Output Rise Time
vs. Input Voltage
4
700
ON RESISTANCE (MΩ)
SUPPLY ON CURRENT (µA)
100
3
4
5
INPUT VOLTAGE (V)
6
240
2
3
4
5
INPUT VOLTAGE (V)
6
Short Circuit Current Limit
vs. Input Voltage
280
85°C
CURRENT (mA)
270
260 25°C
250
240
–40°C
230
220
210
200
2
March 2000
3
4
5
INPUT VOLTAGE (V)
5
6
MIC2536
MIC2536
Micrel
Functional Characteristics
VFLG
VEN
(5V/div) (10V/div)
VOUT
(5V/div)
VIN = 5V
CIN = 4.7µF
RL = 50Ω
CL = 1µF
Turnoff
(MIC2536-1)
Turn-On
(MIC2536-1)
(output current limited)
Turnoff
(MIC2536-1)
Enabled Into Short Circuit
(MIC2536-1)
VFLG
VEN
(5V/div) (10V/div)
Time (1ms/div)
RL = 35Ω
CL = 47µF || 10µF
IOUT
(100mA/div)
VOUT
IOUT
(200mA/div) (5V/div)
VIN = 5V
CIN = 4.7µF
RL = 35Ω
CL = 10µF
RL = 35Ω
CL = 47µF || 10µF
Time (1ms/div)
VOUT
(5V/div)
VFLG
VEN
(5V/div) (10V/div)
VIN = 5V
CIN = 4.7µF
VOUT
IOUT
(100mA/div) (5V/div)
RL = 35Ω
CL = 10µF
IOUT
(100mA/div)
VOUT
(5V/div)
VIN = 5V
CIN = 4.7µF
VFLG
VEN
(5V/div) (10V/div)
Time (1ms/div)
VFLG
VEN
(5V/div) (10V/div)
Time (1ms/div)
Time (5µs/div)
MIC2536
March
2000
VIN = 5V
CIN = 4.7µF
IOUT
(100mA/div)
VFLG
VEN
(5V/div) (10V/div)
Turn-On
(MIC2536-1)
VOUT
IOUT
(100mA/div) (5V/div)
Turn-On / Turnoff
(MIC2536-1)
tD
VIN = 5V
CIN = 4.7µF
OUT = GND
CL = 0
Time (10ms/div)
5
6
March
MIC2536
2000
MIC2536
Micrel
Inrush Current
(MIC2536-1)
VFLG
VEN
(5V/div) (10V/div)
VFLG
VEN
(5V/div) (10V/div)
Ramped Into Short Circuit
(MIC2536-1)
CL = 110µF
CL = 210µF
CL = 310µF
CL = 410µF
IOUT
(100mA/div)
VOUT
(5V/div)
VIN = 5V
CIN = 4.7µF
RL = 0Ω
IOUT
(200mA/div)
Thermal Shutdown
Time (100ms/div)
VIN = 5V
CIN = 4.7µF
RL = 35Ω
CL = 10
Time (5µs/div)
Current-Loop Response
(MIC2536-1)
IOUT
(1A/div)
VOUT
(5V/div)
output = open
output = ground
VEN = 5V
VIN = 5V
CIN = 4700µF
CL = 47µF
Time (5µs/div)
March 2000
7
MIC2536
MIC2536
Micrel
Block Diagram
FLGA
DELAY
OUTA
ENA
CHARGE
PUMP
GATE
CONTROL
CURRENT
LIMIT
OSC.
THERMAL
SHUTDOWN
1.2V
REFERENCE
CHARGE
PUMP
GATE
CONTROL
IN
CURRENT
LIMIT
ENB
DELAY
OUTB
FLGB
MIC2536
GND
MIC2536
8
March 2000
MIC2536
Micrel
Equations that can be used to calculate power dissipation
and die temperature are found below:
Calculation of power dissipated by each channel can be
accomplished by the following equation:
PD = RDS(on) × (IOUT)2
Functional Description
The MIC2536-1 and MIC2536-2 are dual high-side switches
with active-high and active-low enable inputs, respectively.
Fault conditions turn off or inhibit turn-on of one or more of the
output transistors, depending upon the type of fault, and
activate the open-drain error flag transistors making them
sink current to ground.
Input and Output
IN (input) is the power supply connection to the logic circuitry
and the drain of each output MOSFET. OUTx (output) is the
source of each respective MOSFET. In a typical circuit,
current flows through the switch from IN to OUTx toward the
load. If VOUT is greater than VIN, current will flow from OUT
to IN during an on-condition since the MOSFET is bidirectional when enabled.
The output MOSFET and driver circuitry are also designed to
allow the MOSFET source to be externally forced to a higher
voltage than the drain (VOUTx > VIN) when the output is
disabled. In this situation, the MIC2536 prevents reverse
current flow.
Thermal Shutdown
Each output MOSFET has its own thermal sensor. If either or
both channels reach 135°C, affected channel(s) will be shut
down and flag(s) asserted. 10°C of hysteresis prevents the
switches from turning on until the die temperature drops to
125°C. Overtemperature detection functions only when at
least one switch is enabled.
The MIC2536 will automatically reset its output when the die
temperature cools to approximately 125°C. The MIC2536
output and FLG signal will continue to cycle on and off until the
device is disabled or the fault is removed.
Depending on PCB layout, package, ambient temperature,
etc., it may take several hundred milliseconds from the
occurrence of the fault to the output MOSFET being shut off.
Delay to reach thermal shutdown will be shortest with a dead
short on the output.
Current-Limit Induced Thermal Shutdown
Internal circuitry increases the output MOSFET on-resistance until the series combination of the MOSFET on-resistance and the load impedance limits output current to approximately 275mA. The resulting increase in power dissipation may cause the shorted channel to go into thermal
shutdown. In addition, even though individual channels are
thermally isolated, it is possible they may shut down when an
adjacent channel is shorted. When this is undesirable, thermal shutdown can be avoided by externally responding to the
fault and disabling the current-limited channel before the
shutdown temperature is reached. The delay between the
flag indication of a current-limit fault and thermal shutdown
will vary with ambient temperature, board layout, and load
impedance, but is typically several seconds. The USB controller must therefore recognize a fault and disable the
appropriate channel within this time.
Power Dissipation
Power dissipation depends on several factors such as the
load, PCB layout, ambient temperature and package type.
March 2000
Total power dissipation of the device will be the summation
of PD for both channels. To relate this to junction
temperature, the following equation can be used:
Tj = PD × θJA + TA
where:
Tj = junction temperature
TA = ambient temperature
θJA = is the thermal resistance of the package
Current Sensing and Limiting
The current-limit threshold is preset internally. The preset
level prevents damage to the output MOSFET and external
load but allows a minimum current of 150mA through the
output MOSFET of each channel.
The current-limit circuit senses a portion of the output FET
switch current. The current sense resistor shown in the block
diagram is virtual and has no voltage drop. The reaction to an
overcurrent condition varies with the following three scenarios:
Switch Enabled into Short Circuit
If a switch is enabled into a heavy load or short circuit, the
switch immediately goes into a constant-current mode, reducing the output voltage. The FLG is asserted indicating an
overcurrent condition.
Short Circuit Applied to Output
When a heavy load or short circuit is applied to an enabled
switch, a large transient current may flow until the currentlimit circuitry responds. Once this occurs, the device limits
current to less than the maximum short-circuit current-limit
specification.
Current-Limit Response Ramped Load
The MIC2536 current-limit profile exhibits a small foldback
effect of approximately 100mA. Once this current-limit threshold is exceeded the device enters constant-current mode.
This constant current is specified as the short-circuit currentlimit in the “Electrical Characteristics” table. It is important to
note that the MIC2536 will deliver load current up to the
current-limit threshold before entering current-limited operation.
Fault Flag
FLGx is an open-drain N-channel MOSFET output. Fault
flags are active (low) for current-limit or thermal shutdown. In
the case where an overcurrent condition occurs, FLG will be
asserted only after the flag response delay time, tD has
elapsed. This ensures that FLG is asserted only upon valid
overcurrent conditions and that erroneous error reporting is
eliminated. False overcurrent conditions can occur during
hot-plug events when a highly capacitive load is connected
and causes a high transient inrush current that exceeds the
current-limit threshold. The flag response delay time is typically 12ms.
9
MIC2536
MIC2536
Micrel
Enable Input
EN must be driven logic high or logic low for a clearly defined
input. Floating the input may cause unpredictable operation.
EN should not be allowed to go negative with respect to GND.
Printed Circuit Board Hot-Plug
The MIC2536 is an ideal inrush current-limiter for hot-plug
applications. Due to the integrated charge pump, the MIC2536
presents a high impedance when off and slowly becomes a
low impedance as it turns on. This “soft-start” feature effectively isolates power supplies from highly capacitive loads by
reducing inrush current. Figure 2 shows how the MIC2536
may be used in a hot-plug card application.
Overcurrent Transients
The MIC2536 incorporates an internal circuit designed to
prevent FLG from being asserted due to transient inrush
current. Overcurrent events <12ms (typ.) will not assert FLG.
In case of large capacitive loads (i.e., >430µF), the length of
the transient due to inrush current may exceed the delay
provided by the integrated filter. Since this inrush current
exceeds the current-limit delay specification, FLG will be
asserted during this time. To prevent the logic controller from
responding to FLG being asserted, an external RC filter, as
shown in Figure 3, can be used to filter out transient FLG
assertion. The value of the RC time constant should be
selected to match the length of the transient, minus flag tD.
Applications Information
Supply Filtering
A 0.1µF to 1µF bypass capacitor from IN to GND, located at
the device, is strongly recommended to control supply transients. Without a bypass capacitor, an output short may
cause sufficient ringing on the input (from supply lead inductance) to damage internal control circuitry.
Input or output transients must not exceed the absolute
maximum supply voltage (VIN(max) = 6V) even for a short
duration.
VIN
2.7V to 5.5V
MIC2536
ENA
OUTA
FLGA
IN
FLGB
GND
ENB
OUTB
0.1µF to 1µF
Figure 1. Supply Bypassing
MIC2536-2
1
VCC
0.1
µF
to "Hot"
Receptacle
OUTA
EN
8
2
FLGA
IN
3
7
FLGB
GND
6
4
ENB
OUTB
5
Backend
Function
CBULK
GND
Adaptor Card
Figure 2. Hot-Plug Card Application
V+
Logic Controller
OVERCURRENT
MIC2536
10k
1
R
C
2
3
4
EN
OUTA
FLGA
IN
FLGB
GND
ENB
OUTB
8
7
6
5
Figure 3. Transient Filter
MIC2536
10
March 2000
MIC2536
Micrel
may not consume more than 500µA. In a nonconfigured state
all downstream devices will be switched off. In most cases, a
nonconfigured hub is not a practical state for the system.
Therefore, the 2.5mA specification is the applicable target
specification for the suspend state. In a bus-powered hub
with less than 4 ports, the hub may use the additional current
for internal functions.
The 500µA worst case suspend current must be further
divided among the data port termination resistors and internal
functions. The termination resistors will consume
3.6V ÷ (16.5KΩ – 5%) = 230µA. This leaves only 270µA for
internal functions. Assuming 100µA as the maximum USB
controller suspend current, 170µA remains for the rest of the
system. The MIC2536 will consume 100µA maximum, leaving a margin of 70µA.
USB Voltage Regulation
USB specifications require a minimum downstream voltage
supply of 4.40V from a bus-powered hub port (See Application Note 17 for details). The USB specification allows for a
100mV drop across the hub, leaving 250mV for PCB, upstream cable, and connector resistance. Therefore, the onresistance of the switch for each port, not including PCB
resistance, must be <100mV ÷ 100mA = 1Ω. The MIC2536
has a maximum on-resistance of 700mΩ, which easily satisfies this requirement.
Overcurrent Indication
The USB Specification does not require bus-powered hubs to
report overcurrent conditions to the host, since the hub is
already current-limited at the upstream port. However, if it is
desired to report overcurrent, the Hub Descriptor Status
Register must be programmed to indicate this. The MIC2536
provides a flag output for this application.
Universal Serial Bus (USB) Power Distribution
Applications
The MIC2536 is ideally suited for USB (Universal Serial Bus)
power distribution applications. For Bus-Powered hubs, USB
requires that each downstream port be switched on or off
under control by the host. Up to four downstream ports each
capable of supplying 100mA at 4.4V minimum are allowed. In
additon, to reduce voltage droop on the upstream bus the hub
must consume only 100mA max at start-up until it enumerates with the host prior to requesting more power. The same
requirements apply for bus-powered peripherals that have no
downstream ports. Figure 4 shows a two-port bus-powered
hub.
Bus-Powered Hub Port Switching
The USB Specification requires that bus-powered hubs implement port switching on either a ganged or individual basis.
The specific implementation must be reported via the Hub
Descriptor Status Register. Individual port switching has
advantages in that a fault on one port will not prevent the other
ports from operating correctly. In addition, a soft-start circuit
must be included in order to reduce inrush currents when the
switch is enabled. To meet this requirement, the MIC2536
has been designed to slowly ramp its output.
Suspend Current
Universal Serial Bus Specification places a maximum suspend current requirement of 500µA on devices. For hubs,
Universal Serial Bus Specification Revision 1.1 clarifies this
issue. Revision 1.1, section 7.2.3, stipulates that the maximum suspend current for a configured hub is 2.5mA. This
number is derived by allocating 500µA for up to four downstream ports plus 500µA for the hub’s internal functions. A
nonconfigured hub is considered a low-power device and
Ferrite
Beads
10k
4.50V to 5.25V
Upstream VBUS
100mA max.
VBUS
1.5k
10k
VBUS
IN
D+
D–
GND
4.7µF
VIN
OUT
GND
D+
3.3V USB Controller
MIC5207-3.3
1µF
MIC2536-2
ON/OFF
ENA
63µF
OUTA
OVERCURRENT
FLGA
OVERCURRENT
FLGB
GND
ENB
OUTB
ON/OFF
.01µF
IN
D–
USB
Port 1
GND
0.1µF
VBUS
D+
.01µF
63µF
D–
USB
Port 2
GND
Data
Data
(Two Pair)
to USB
Controller
Figure 4. USB Two-Port Bus-Powered Hub
March 2000
11
MIC2536
MIC2536
Micrel
Package Information
0.026 (0.65)
MAX)
PIN 1
0.157 (3.99)
0.150 (3.81)
DIMENSIONS:
INCHES (MM)
0.020 (0.51)
0.013 (0.33)
0.050 (1.27)
TYP
0.064 (1.63)
0.045 (1.14)
45°
0.0098 (0.249)
0.0040 (0.102)
0.197 (5.0)
0.189 (4.8)
0°–8°
0.010 (0.25)
0.007 (0.18)
0.050 (1.27)
0.016 (0.40)
SEATING
PLANE
0.244 (6.20)
0.228 (5.79)
8-Lead SOP (M)
0.122 (3.10)
0.112 (2.84)
0.199 (5.05)
0.187 (4.74)
DIMENSIONS:
INCH (MM)
0.120 (3.05)
0.116 (2.95)
0.036 (0.90)
0.032 (0.81)
0.043 (1.09)
0.038 (0.97)
0.012 (0.30) R
0.012 (0.03)
0.0256 (0.65) TYP
0.008 (0.20)
0.004 (0.10)
5° MAX
0° MIN
0.007 (0.18)
0.005 (0.13)
0.012 (0.03) R
0.039 (0.99)
0.035 (0.89)
0.021 (0.53)
8-Lead MSOP (MM)
MIC2536
12
March 2000
MIC2536
Micrel
MICREL INC. 1849 FORTUNE DRIVE
TEL
+ 1 (408) 944-0800
FAX
SAN JOSE, CA 95131
+ 1 (408) 944-0970
WEB
USA
http://www.micrel.com
This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or
other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc.
© 2000 Micrel Incorporated
March 2000
13
MIC2536
Similar pages