AD AD7780 24-bit, pin-programmable, ultralow power sigma-delta adc Datasheet

24-Bit, Pin-Programmable,
Ultralow Power Sigma-Delta ADC
AD7780
Pin-programmable filter response
Update rate: 10 Hz or 16.7 Hz
Pin-programmable in-amp gain
Pin-programmable power-down and reset
Status function
Internal clock oscillator
Internal bridge power-down switch
Current
115 μA typical (gain = 1)
330 μA typical (gain = 128)
Simultaneous 50 Hz/60 Hz rejection
Power supply: 2.7 V to 5.25 V
−40°C to +105°C temperature range
Independent interface power supply
Packages
14-lead, narrow body SOIC
16-lead TSSOP
2-wire serial interface (read-only device)
SPI compatible
Schmitt trigger on SCLK
FUNCTIONAL BLOCK DIAGRAM
GND AVDD GAIN
REFIN(+) REFIN(–)
AIN(+)
DOUT/RDY
G=1
OR 128
24-BIT Σ-Δ
ADC
AIN(–)
SCLK
BPDSW
INTERNAL
CLOCK
AD7780
DVDD
FILTER
PDRST
07945-001
FEATURES
Figure 1.
Table 1.
Parameter
Output Data Rate
RMS Noise
P-P Resolution
Settling Time
Gain = 128
10 Hz
16.7 Hz
44 nV
65 nV
17.6
17.1
300 ms
120 ms
Gain = 1
10 Hz
16.7 Hz
2.4 μV
2.7 μV
18.8
18.7
300 ms
120 ms
APPLICATIONS
Weigh scales
Pressure measurement
Industrial process control
Portable instrumentation
GENERAL DESCRIPTION
The AD7780 is a complete low power front-end solution for
bridge sensor products, including weigh scales, strain gages, and
pressure sensors. It contains a precision, low power, 24-bit sigmadelta (Σ-Δ) ADC; an on-chip, low noise programmable gain
amplifier (PGA); and an on-chip oscillator.
Consuming only 330 μA, the AD7780 is particularly suitable for
portable or battery-operated products where very low power is
required. The AD7780 also has a power-down mode that allows
the user to switch off the power to the bridge sensor and power
down the AD7780 when not converting, thus increasing the
battery life of the product.
For ease of use, all the features of the AD7780 are controlled by
dedicated pins. Each time a data read occurs, eight status bits
are appended to the 24-bit conversion. These status bits contain
a pattern sequence that can be used to confirm the validity of
the serial transfer.
The on-chip PGA has a gain of 1 or 128, supporting a full-scale
differential input of ±5 V or ±39 mV. The device has two filter
response options. The filter response at the 16.7 Hz update rate
provides superior dynamic performance. The settling time is
120 ms at this update rate. At the 10 Hz update rate, the filter
response provides greater than −45 dB of stop-band attenuation.
In load cell applications, this stop-band rejection is useful to reject
low frequency mechanical vibrations of the load cell. The settling
time is 300 ms at this update rate. Simultaneous 50 Hz/60 Hz
rejection occurs at both the 10 Hz and 16.7 Hz update rates.
The AD7780 operates with a power supply from 2.7 V to 5.25 V.
It is available in a narrow body, 14-lead SOIC package and a 16-lead
TSSOP package.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
AD7780* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
REFERENCE DESIGNS
View a parametric search of comparable parts.
• CN0107
EVALUATION KITS
REFERENCE MATERIALS
• AD7780 Evaluation Board
Solutions Bulletins & Brochures
DOCUMENTATION
• Test & Instrumentation Solutions Bulletin, Volume 10,
Issue 3
Application Notes
Technical Articles
• AN-1187: Radiated Immunity Performance of the AD7780
in Weigh Scale Applications
• High-resolution ADCs — an overview
• MS-2210: Designing Power Supplies for High Speed ADC
• AN-968: Current Sources: Options and Circuits
Data Sheet
DESIGN RESOURCES
• AD7780: 24-Bit, Pin-Programmable, Ultralow Power
Sigma-Delta ADC Data Sheet
• AD7780 Material Declaration
User Guides
• Quality And Reliability
• UG-078: Evaluation Board for the AD7780 24-Bit, PinProgrammable, Low Power, Sigma-Delta ADC
• Symbols and Footprints
SOFTWARE AND SYSTEMS REQUIREMENTS
• AD7780 - No-OS Driver for Microchip Microcontroller
Platforms
• AD7780 - No-OS Driver for Renesas Microcontroller
Platforms
• AD7780 IIO Low Power Sigma-Delta ADC Linux Driver
• AD7780 Pmod Xilinx FPGA Reference Design
• AD7780 Evaluation Board Software
TOOLS AND SIMULATIONS
• Sigma-Delta ADC Tutorial
• PCN-PDN Information
DISCUSSIONS
View all AD7780 EngineerZone Discussions.
SAMPLE AND BUY
Visit the product page to see pricing options.
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7780
TABLE OF CONTENTS
Features .............................................................................................. 1
Power-Down/Reset (PDRST) ................................................... 12
Applications ....................................................................................... 1
Analog Input Channel ............................................................... 12
Functional Block Diagram .............................................................. 1
Bipolar Configuration................................................................ 12
General Description ......................................................................... 1
Data Output Coding .................................................................. 12
Revision History ............................................................................... 2
Reference ..................................................................................... 12
Specifications..................................................................................... 3
Bridge Power-Down Switch ...................................................... 13
Timing Characteristics ................................................................ 5
Digital Interface .......................................................................... 13
Absolute Maximum Ratings............................................................ 6
Applications Information .............................................................. 14
Thermal Resistance ...................................................................... 6
Weigh Scales ................................................................................ 14
ESD Caution .................................................................................. 6
Performance in a Weigh Scale System ..................................... 14
Pin Configurations and Function Descriptions ........................... 7
EMI Recommendations............................................................. 14
Typical Performance Characteristics ............................................. 8
Grounding and Layout .............................................................. 15
Output Noise and Resolution........................................................ 10
Outline Dimensions ....................................................................... 16
Theory of Operation ...................................................................... 11
Ordering Guide .......................................................................... 16
Filter, Data Rate, and Settling Time ......................................... 11
Gain .............................................................................................. 12
REVISION HISTORY
9/09—Rev. 0 to Rev. A
Changes to Specifications Table ...................................................... 3
4/09—Revision 0: Initial Version
Rev. A | Page 2 of 16
AD7780
SPECIFICATIONS
AVDD = 2.7 V to 5.25 V, VREF = AVDD, DVDD = 2.7 V to 5.25 V, GND = 0 V, all specifications TMIN to TMAX, unless otherwise noted. 1
Table 2.
Parameter
Min
ADC CHANNEL
Output Update Rate (fADC)
No Missing Codes 2
Resolution Peak-to-Peak
RMS Noise
Integral Nonlinearity
Offset Error
24
Hz
Hz
Bits
FILTER = 1, settling time = 3/fADC
FILTER = 0, settling time = 2/fADC
ppm of FSR
μV
μV
μV
μV
nV/°C
nV/°C
nV/°C
% of FS
ppm/°C
dB
dB
63
75
dB
72
90
dB
50 Hz ± 1 Hz, 60 Hz ± 1 Hz, fADC =
16.7 Hz
50 Hz ± 1 Hz, 60 Hz ± 1 Hz, fADC = 10 Hz
90
90
110
dB
dB
dB
Gain = 1, AIN = 1 V
Gain = 128, AIN = 7.81 mV
50 Hz ± 1 Hz, 60 Hz ± 1 Hz
±VREF/gain
V
VREF = REFIN(+) − REFIN(−), gain = 1
or 128
Gain = 1
Gain = 128, FILTER = 0
Gain = 128, FILTER = 1, AVDD ≤ 3.6 V
Gain = 128, FILTER = 1, AVDD > 3.6 V
Gain = 1
Gain = 128
GND + 100 mV
GND + 450 mV
GND + 1.1
GND + 1.5
Average Input Current
Average Input Current Drift
REFERENCE
External REFIN Voltage
Reference Voltage Range2
Absolute REFIN Voltage Limits2
Average Reference Input Current
Average Reference Input Current Drift
Normal-Mode Rejection
Common-Mode Rejection
BRIDGE POWER-DOWN SWITCH (BPDSW)
RON
Allowable Current2
INTERNAL CLOCK
Frequency
Duty Cycle
Test Conditions/Comments
±6
±6
±200
±1
±2
±10
±150
±10
±0.25
±2
100
120
50 Hz, 60 Hz
ANALOG INPUTS
Differential Input Voltage Range
Absolute AIN Voltage Limits2
Unit
See Table 7 and Table 8
See Table 7 and Table 8
Full-Scale Error
Gain Drift vs. Temperature
Power Supply Rejection
50 Hz, 60 Hz
Common-Mode Rejection
DC
Max
10
16.7
Offset Error Drift vs. Temperature
Normal-Mode Rejection2
50 Hz, 60 Hz
Typ
AVDD − 100 mV
AVDD − 1.1
AVDD − 1.1
AVDD − 1.5
±1
±250
±3
AVDD
V
V
V
V
nA
pA typ
pA/°C
400
±0.15
V
V
V
nA/V
nA/V/°C
110
dB
0.5
GND − 30 mV
AVDD
AVDD + 30 mV
Gain = 128 with FILTER = 1
Gain = 1 with FILTER = 1
Gain = 128 with FILTER = 0
Gain = 1 with FILTER = 0
Gain = 128
Gain = 1 with FILTER = 1
Gain = 1 with FILTER = 0
Gain = 128, FILTER = 1, AIN = 7.81 mV
Gain = 128, FILTER = 0, AIN = 7.81 mV
REFIN = REFIN(+) − REFIN(−)
Same as for analog inputs
Controlled via the PDRST pin
64 − 3%
9
30
Ω
mA
64 + 3%
kHz
%
50:50
Rev. A | Page 3 of 16
Continuous current
AD7780
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
0.4
0.8
100
V
V
V
V
mV
DVDD = 3 V
DVDD = 5 V
DVDD = 3 V
DVDD = 5 V
DVDD = 3 V
140
±2
10
mV
μA
pF
DVDD = 5 V
VIN = DVDD or GND
All digital inputs
0.4
0.4
V
V
V
V
μA
pF
DVDD = 3 V, ISOURCE = 100 μA
DVDD = 5 V, ISOURCE = 200 μA
DVDD = 3 V, ISINK = 100 μA
DVDD = 5 V, ISINK = 1.6 mA
5.25
5.25
V
V
LOGIC INPUTS
SCLK, FILTER, GAIN, PDRST2
Input Low Voltage, VINL
Input High Voltage, VINH
1.8
2.4
SCLK (Schmitt-Triggered Input)
Hysteresis
Input Currents
Input Capacitance
LOGIC OUTPUT (DOUT/RDY)
Output High Voltage, VOH2
DVDD − 0.6
4
Output Low Voltage, VOL2
Floating-State Leakage Current
Floating-State Output Capacitance
Data Output Coding
POWER REQUIREMENTS 3
Power Supply Voltage
AVDD to GND
DVDD to GND
Power Supply Currents
IDD Current
IDD (Power-Down/Reset Mode)
±2
10
Offset binary
2.7
2.7
115
130
330
420
10
160
500
1
μA
μA
μA
μA
μA
Temperature range is −40°C to +105°C.
This specification is not production tested but is supported by characterization data at initial product release.
3
Digital inputs are equal to DVDD or GND.
2
Rev. A | Page 4 of 16
Gain = 1, AVDD = 3 V
Gain = 1, AVDD = 5 V
Gain = 128, AVDD = 3 V
Gain = 128, AVDD = 5 V
AD7780
TIMING CHARACTERISTICS
AVDD = 2.7 V to 5.25 V, DVDD = 2.7 V to 5.25 V, GND = 0 V, Input Logic 0 = 0 V, Input Logic 1 = DVDD, unless otherwise noted.
Table 3.
Parameter 1
Read 2
t1
t2
t3 3
t4
Reset
t5
t6 5
Limit at TMIN, TMAX
Unit
Test Conditions/Comments
100
100
0
60
80
10
130
ns min
ns min
ns min
ns max
ns max
ns min
ns max
SCLK high pulse width
SCLK low pulse width
SCLK active edge to data valid delay 4
DVDD = 4.75 V to 5.25 V
DVDD = 2.7 V to 3.6 V
SCLK inactive edge to DOUT/RDY high
100
ns min
120
300
ms typ
ms typ
PDRST low pulse width
FILTER/GAIN change to data valid delay
Update rate = 16.7 Hz
Update rate = 10 Hz
1
Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of DVDD) and timed from a voltage level of 1.6 V.
See Figure 3.
The values of t3 are measured using the load circuit of Figure 2 and are defined as the time required for the output to cross the V OL or VOH limits.
4
SCLK active edge is falling edge of SCLK.
5
The PDRST high to data valid delay is typically 1 ms longer than t6 because the internal oscillator requires time to power up and settle.
2
3
Circuit and Timing Diagrams
ISINK (1.6mA WITH DVDD = 5V,
100µA WITH DVDD = 3V)
PDRST
(INPUT)
t5
TO
OUTPUT
PIN
DOUT/RDY
(OUTPUT)
07945-002
Figure 2. Load Circuit for Timing Characterization
MSB
Figure 4. Resetting the AD7780
GAIN OR FILTER
(INPUT)
LSB
t3
t6
t4
t1
07945-005
ISOURCE (200µA WITH DVDD = 5V,
100µA WITH DVDD = 3V)
DOUT/RDY
(OUTPUT)
07945-004
1.6V
50pF
t2
07945-003
DOUT/RDY
(OUTPUT)
SCLK
(INPUT)
Figure 5. Changing Gain or Filter Option
Figure 3. Read Cycle Timing Diagram
Rev. A | Page 5 of 16
AD7780
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
THERMAL RESISTANCE
Table 4.
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Parameter
AVDD to GND
DVDD to GND
Analog Input Voltage to GND
Reference Input Voltage to GND
Digital Input Voltage to GND
Digital Output Voltage to GND
AIN/Digital Input Current
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Lead Temperature, Soldering Reflow
Rating
−0.3 V to +7 V
−0.3 V to +7 V
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to DVDD + 0.3 V
−0.3 V to DVDD + 0.3 V
10 mA
−40°C to +105°C
−65°C to +150°C
150°C
260°C
Table 5.
Package Type
14-Lead SOIC
16-Lead TSSOP
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. A | Page 6 of 16
θJA
104.5
150.4
θJC
42.9
27.6
Unit
°C/W
°C/W
AD7780
NC
1
16
NC
SCLK
2
15
FILTER
14 FILTER
DOUT/RDY
3
14
PDRST
13 PDRST
NC
4
13
DVDD
12 DVDD
GAIN
5
12
AVDD
TOP VIEW 11 AVDD
(Not to Scale)
AIN(+) 5
10 GND
AIN(+)
6
11
GND
AIN(–)
7
10
BPDSW
REFIN(+)
8
9
SCLK 1
DOUT/RDY 2
NC 3
AD7780
GAIN 4
9
REFIN(+) 7
8
BPDSW
REFIN(–)
NC = NO CONNECT
07945-006
AIN(–) 6
AD7780
TOP VIEW
(Not to Scale)
REFIN(–)
NC = NO CONNECT
Figure 6. SOIC Pin Configuration
07945-007
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 7. TSSOP Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
SOIC TSSOP
1
2
Mnemonic
SCLK
2
3
DOUT/RDY
3
4
5
6
7
1, 4, 16
5
6
7
8
NC
GAIN
AIN(+)
AIN(−)
REFIN(+)
8
9
9
10
REFIN(−)
BPDSW
10
11
12
11
12
13
GND
AVDD
DVDD
13
14
PDRST
14
15
FILTER
Description
Serial Clock Input. This serial clock input is for data transfers from the ADC. The SCLK pin has a Schmitttriggered input. The serial clock can be active only when transferring data from the AD7780. The data
from the AD7780 can be read as a continuous 32-bit word. Alternatively, SCLK can be noncontinuous
during the data transfer, with the information being transmitted from the ADC in smaller data batches.
Serial Data Output/Data Ready Output. DOUT/RDY serves a dual purpose: as a data ready pin, going low to
indicate the completion of a conversion, and as a serial data output pin to access the data register of the
ADC. Eight status bits accompany each data read (see Figure 22). The DOUT/RDY falling edge can be used
as an interrupt to a processor, indicating that new data is available. If the data is not read after the conversion, the pin goes high before the next update occurs. The serial interface is reset each time that a conversion is
available. Therefore, the user must ensure that any conversions being transmitted are completed before
the next conversion is available.
No Connect. This pin can be left floating.
Gain Select Pin. When GAIN is low, the gain is set to 128. When GAIN is high, the gain is set to 1.
Analog Input. AIN(+) is the positive terminal of the differential analog input pair, AIN(+)/AIN(−).
Analog Input. AIN(−) is the negative terminal of the differential analog input pair, AIN(+)/AIN(−).
Positive Reference Input. An external reference can be applied between REFIN(+) and REFIN(−). The nominal reference voltage (REFIN(+) − REFIN(−)) is 5 V, but the part can function with a reference of 0.5 V to AVDD.
Negative Reference Input.
Bridge Power-Down Switch to GND. When PDRST is high, the bridge power-down switch is closed. When
PDRST is low, the switch is opened.
Ground Reference Point.
Supply Voltage, 2.7 V to 5.25 V.
Digital Interface Supply Voltage. The logic levels for the serial interface pins and the digital control pins
are related to this supply, which is between 2.7 V and 5.25 V. The DVDD voltage is independent of the
voltage on AVDD; therefore, AVDD can equal 5 V with DVDD at 3 V or vice versa.
Power-Down/Reset. When this pin is low, the ADC is placed in power-down mode, and the low-side power
switch is opened. All the logic on the chip is reset, and the DOUT/RDY pin is tristated. When PDRST is high,
the ADC is taken out of power-down mode. The on-chip clock powers up and settles, and the ADC
continuously converts. In addition, the low-side power switch is closed. The internal clock requires
approximately 1 ms to power up.
Filter Select. When FILTER is low, the fast settling filter is selected. The update rate is set to 16.7 Hz, which
gives a filter settling time of 120 ms. When FILTER is high, the high rejection filter is selected. The update
rate is set to 10 Hz, which gives a filter settling time of 300 ms. With this filter, the stop-band (higher than
fADC) attenuation is better than −45 dB.
Rev. A | Page 7 of 16
AD7780
TYPICAL PERFORMANCE CHARACTERISTICS
60
8,388,670
8,388,660
8,388,650
OCCURRENCE
8,388,640
CODE
8,388,630
8,388,620
8,388,610
8,388,600
40
20
8,388,590
0
200
400
600
800
1000
SAMPLE
0
8,388,390
07945-008
8,388,570
8,388,408
8,388,426
07945-011
8,388,580
8,388,444
CODE
Figure 11. Noise Distribution Histogram
(VREF = AVDD, Update Rate = 10 Hz, Gain = 128)
Figure 8. Noise (VREF = AVDD, Update Rate = 16.7 Hz, Gain = 128)
60
8,388,630
8,388,625
8,388,615
40
CODE
OCCURRENCE
8,388,620
8,388,610
8,388,605
8,388,600
20
8,388,595
8,388,594
8,388,618
8,388,642
8,388,666
CODE
8,388,585
07945-009
0
8,388,570
0
200
400
600
800
1000
SAMPLE
Figure 9. Noise Distribution Histogram
(VREF = AVDD, Update Rate = 16.7 Hz, Gain = 128)
Figure 12. Noise (VREF = AVDD, Update Rate = 16.7 Hz, Gain = 1)
8,388,460
200
8,388,450
150
OCCURRENCE
8,388,430
8,388,420
8,388,410
100
50
8,388,390
0
200
400
600
800
1000
SAMPLE
Figure 10. Noise (VREF = AVDD, Update Rate = 10 Hz, Gain = 128 )
0
8,388,585 8,388,593 8,388,601 8,388,609 8,388,617 8,388,625
CODE
Figure 13. Noise Distribution Histogram
(VREF = AVDD, Update Rate = 16.7 Hz, Gain = 1)
Rev. A | Page 8 of 16
07945-013
8,388,400
07945-010
CODE
8,388,440
07945-012
8,388,590
AD7780
8,388,415
2.0
8,388,410
1.5
1.0
INL (ppm FS)
8,388,400
8,388,395
8,388,390
0
–0.5
0
200
400
600
800
1000
SAMPLE
–2.0
–6
–4
–2
0
2
4
6
VIN (V)
Figure 14. Noise (VREF = AVDD, Update Rate = 10 Hz, Gain = 1)
07945-017
–1.5
07945-014
8,388,380
0.5
–1.0
8,388,385
Figure 17. Integral Nonlinearity (VREF = AVDD, Gain = 1)
100
10
8
6
75
OFFSET (µV)
OCCURRENCE
4
50
2
0
–2
–4
25
–6
8,388,403
8,388,409
8,388,415
CODE
–10
–60
–40
–20
0
20
40
60
80
100
120
07945-018
8,388,397
07945-015
8,388,391
120
07945-019
–8
0
8,388,385
TEMPERATURE (°C)
Figure 15. Noise Distribution Histogram
(VREF = AVDD, Update Rate = 10 Hz, Gain = 1)
Figure 18. Offset vs. Temperature (Gain = 128)
150
3.0
2.5
100
2.0
GAIN ERROR (ppm)
1.5
1.0
0.5
0
–0.5
50
0
–50
–100
–1.0
–150
–1.5
–2.0
–2.5
–0.04
–0.03
–0.02
–0.01
0
0.01
0.02
0.03
0.04
VIN (V)
–200
–60
07945-016
INL (ppm FS)
CODE
8,388,405
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 19. Gain Error vs. Temperature (Gain = 128)
Figure 16. Integral Nonlinearity (VREF = AVDD, Gain = 128)
Rev. A | Page 9 of 16
AD7780
OUTPUT NOISE AND RESOLUTION
Table 7 and Table 8 show the rms noise of the AD7780 for the two output data rates and gain settings when 3 V and 5 V references are used.
These numbers are typical and are generated using a differential input voltage of 0 V. The corresponding peak-to-peak (p-p) resolution is
also listed. The p-p resolution represents the resolution for which there is no code flicker.
Table 7. RMS Noise and Peak-to-Peak Resolution when AVDD = 3 V and VREF = 3 V
Parameter
Update Rate
RMS Noise
P-P Resolution
10 Hz
44 nV
17.6
Gain = 128
16.7 Hz
65 nV
17.1
10 Hz
2.4 μV
18.8
Gain = 1
16.7 Hz
2.7 μV
18.7
10 Hz
3 μV
19.3
Gain = 1
16.7 Hz
2.7 μV
19.4
Table 8. RMS Noise and Peak-to-Peak Resolution when AVDD = 5 V and VREF = 5 V
Parameter
Update Rate
RMS Noise
P-P Resolution
10 Hz
49 nV
18.2
Gain = 128
16.7 Hz
69 nV
17.7
Rev. A | Page 10 of 16
AD7780
THEORY OF OPERATION
–20
–40
–60
–80
–1000
FILTER, DATA RATE, AND SETTLING TIME
0
When a step change occurs on the analog input, the AD7780
requires several conversion cycles to generate a valid conversion.
If the step change occurs synchronous to the conversion period, the
settling time of the AD7780 must be allowed to generate a valid
40
60
80
100
120
INPUT SIGNAL FREQUENCY (Hz)
Figure 20. Filter Profile with Update Rate = 16.7 Hz (FILTER = 0)
0
–20
FILTER GAIN (dB)
The AD7780 has two filter options. When the FILTER pin is low,
the 16.7 Hz filter is selected; when the FILTER pin is high, the
10 Hz filter is selected. When the polarity of FILTER is changed,
the AD7780 modulator and filter are reset immediately. DOUT/
RDY is set high, and the ADC then begins conversions using
the selected filter response. The first conversion requires the
complete settling time of the filter. Subsequent conversions occur
at the selected update rate. The settling time of the 10 Hz filter is
300 ms (three conversion cycles), and the settling time of the
16.7 Hz filter is 120 ms (two conversion cycles).
20
07945-020
–100
conversion. If the step change occurs asynchronous to the end
of a conversion, an extra conversion must be allowed to generate
a valid conversion. The data register is updated with all the conversions, but, for an accurate result, the user must allow for the
required time.
Figure 20 and Figure 21 show the filter response for each filter.
The 10 Hz filter provides greater than −45 dB of rejection in the
stop band. The only external filtering required on the analog inputs
is a simple R-C filter to provide rejection at multiples of the master
clock. A 1 kΩ resistor in series with each analog input, a 0.01 μF
capacitor from each input to GND, and a 0.1 μF capacitor from
AIN(+) to AIN(−) are recommended.
When the filter is changed, DOUT/RDY goes high and remains
high until the appropriate settling time for that filter elapses
(see Figure 5). Therefore, the user should complete any read
operations before changing the filter. Otherwise, 1s are read
back from the AD7780 because the DOUT/RDY pin is set high
following the filter change.
Rev. A | Page 11 of 16
–40
–60
–80
–100
–1000
0
20
40
60
80
100
120
INPUT SIGNAL FREQUENCY (Hz)
Figure 21. Filter Profile with Update Rate = 10 Hz (FILTER = 1)
07945-021
The device has an internal clock and one buffered differential
input. It offers a choice of two update rates (10 Hz or 16.7 Hz)
and two gain settings (1 or 128). These functions are controlled
using dedicated pins, which makes the interface easy to configure.
A 2-wire interface simplifies data retrieval from the AD7780.
0
FILTER GAIN (dB)
The AD7780 is a low power ADC that incorporates a precision
24-bit, Σ-Δ modulator; a PGA; and an on-chip digital filter
intended for measuring wide dynamic range, low frequency
signals. The part provides a complete front-end solution for
bridge sensor applications such as weigh scales and pressure
sensors.
AD7780
GAIN
BIPOLAR CONFIGURATION
The AD7780 has two gain options: gain = 1 and gain = 128.
When the GAIN pin is low, the gain is set to 128; when the
GAIN pin is high, the gain is set to 1. The acceptable analog
input range is ±VREF/gain. Thus, with VREF = 5 V, the input range
is ±5 V when the GAIN pin is high and ±39 mV when the GAIN
pin is low.
The AD7780 accepts a bipolar input range. A bipolar input range
does not imply that the part can tolerate negative voltages with
respect to system GND. Signals on the AIN(+) input are referenced to the voltage on the AIN(−) input. For example, if AIN(−)
is 2.5 V, the analog input range on the AIN(+) input is 2.46 V to
2.54 V for a gain of 128.
When the polarity of the GAIN pin is changed, the AD7780 modulator and filter are reset immediately. DOUT/RDY is set high, and
the ADC then begins conversions. DOUT/RDY remains high until
the appropriate settling time for the filter elapses (see Figure 5).
Therefore, the user should complete any read operations before
changing the gain. Otherwise, 1s are read back from the AD7780
because the DOUT/RDY pin is set high following the gain change.
The total settling time of the selected filter is required to generate
the first conversion after the gain change; subsequent conversions
occur at the selected update rate.
DATA OUTPUT CODING
POWER-DOWN/RESET (PDRST)
The PDRST pin functions as a power-down pin and a reset pin.
When PDRST is taken low, the AD7780 is powered down. The
entire ADC is powered down (including the on-chip clock), the
low-side power switch is opened, and the DOUT/RDY pin is
tristated. The circuitry and serial interface are also reset, which
resets the logic, the digital filter, and the analog modulator.
PDRST must be held low for 100 ns minimum to initiate the
reset function (see Figure 4) .
When PDRST is taken high, the AD7780 is taken out of powerdown mode. When the on-chip clock has powered up (1 ms,
typically), the modulator begins sampling the analog input. The
low-side power switch is closed, and the DOUT/RDY pin
becomes active.
A reset is automatically performed on power-up.
ANALOG INPUT CHANNEL
The AD7780 has one differential analog input channel. The
input channel feeds into a high impedance input stage of the
amplifier. Therefore, the input can tolerate significant source
impedances and is tailored for direct connection to external
resistive-type sensors such as strain gages.
The absolute input voltage range is restricted to a range between
GND + 300 mV and AVDD − 1.1 V. Care must be taken in setting
up the common-mode voltage to avoid exceeding these limits.
Otherwise, there is degradation in linearity and noise performance.
The AD7780 uses offset binary coding. Thus, a negative fullscale voltage results in a code of 000...000, a zero differential
input voltage results in a code of 100...000, and a positive fullscale input voltage results in a code of 111...111.
The output code for any analog input voltage can be represented as
Code = 2N − 1 × [(AIN × Gain /VREF) + 1]
where:
AIN is the analog input voltage.
Gain is 1 or 128.
N = 24.
REFERENCE
The AD7780 has a fully differential input capability for the channel.
The common-mode range for these differential inputs is GND to
AVDD. The reference input is unbuffered; therefore, excessive R-C
source impedances introduce gain errors. The reference voltage of
REFIN (REFIN(+) − REFIN(−)) is AVDD nominal, but the AD7780
is functional with reference voltages of 0.5 V to AVDD. In applications where the excitation (voltage or current) for the transducer
on the analog input also drives the reference voltage for the part,
the effect of the low frequency noise in the excitation source is
removed because the application is ratiometric. If the AD7780
is used in a nonratiometric application, a low noise reference
should be used.
Recommended 2.5 V reference voltage sources for the AD7780
include the ADR381 and ADR391, which are low noise, low
power references. These references have low output impedances
and are, therefore, tolerant to decoupling capacitors on REFIN(+)
without introducing gain errors in the system. Deriving the
reference input voltage across an external resistor means that
the reference input sees a significant external source impedance.
External decoupling on the REFIN pins is not recommended in
this type of circuit configuration.
The low noise in-amp means that signals of small amplitude can
be amplified within the AD7780, while maintaining excellent noise
performance. The amplifier can be configured to have a gain of 128
or 1, using the GAIN pin. The analog input range is equal to
±VREF/gain. The common-mode voltage (AIN(+) + AIN(−))/2
must be ≥0.5 V.
Rev. A | Page 12 of 16
AD7780
BRIDGE POWER-DOWN SWITCH
The bridge power-down switch (BPDSW) is useful in batterypowered applications where the optimization of system power
consumption is essential. A 350 Ω load cell typically consumes
15 mA when excited with a 5 V power supply. To minimize the
current consumption, the load cell is disconnected when it is
not being used. The bridge power-down switch can be included
in series with the load cell. When PDRST is high, the bridge powerdown switch is closed, and the load cell measures the strain. When
PDRST is low, the bridge power-down switch is opened so no
current flows through the load cell. Therefore, the current
consumption of the system is minimized. The bridge powerdown switch has an on resistance of 9 Ω maximum. The switch
is capable of withstanding 30 mA of continuous current.
DIGITAL INTERFACE
RDY
FILTER
ERR
ID1
ID0
GAIN
PAT1
PAT0
07945-121
The serial interface of the AD7780 consists of two signals: SCLK
and DOUT/RDY. SCLK is the serial clock input for the device,
and data transfers occur with respect to the SCLK signal. The
DOUT/RDY pin is dual purpose: it functions as a data ready pin
and as a data output pin. DOUT/RDY goes low when a new
data-word is available in the output register. A 32-bit word is
placed on the DOUT/RDY pin when sufficient SCLK pulses are
applied. This word consists of a 24-bit conversion result and eight
status bits. Figure 22 shows the status bits, and Table 9 describes
the status bits and their functions.
DOUT/RDY is reset high when the conversion has been read.
If the conversion is not read, DOUT/RDY goes high prior to the
data register update to indicate when not to read from the device.
This ensures that a read operation is not attempted while the register is being updated. Each conversion can be read only once. The
data register is updated for every conversion. When a conversion
is complete, the serial interface is reset, and the new conversion is
placed in the data register. Therefore, the user must ensure that
the complete word is read before the next conversion is complete.
When PDRST is low, the DOUT/RDY pin is tristated. When
PDRST is taken high, the internal clock requires approximately
1 ms to power up. Following power-up, the ADC continuously
converts. The first conversion requires the total settling time (see
Figure 4). DOUT/RDY goes high when PDRST is taken high and
returns low only when a conversion is available. The ADC then
converts continuously, and subsequent conversions are avail-able
at the selected update rate. Figure 3 shows the timing for a read
operation from the AD7780.
When the filter response is changed (using FILTER) or the gain
is changed (using GAIN), the modulator and filter are reset
immediately (see Figure 5). DOUT/RDY is set high. The ADC
then begins conversions using the selected filter response/gain
setting. DOUT/RDY remains high until the appropriate settling
time for that filter has elapsed. Therefore, the user should complete
any read operations before changing the gain or update rate.
Otherwise, 1s are read back from the AD7780 because the
DOUT/RDY pin is set high following the gain/filter change.
Figure 22. Status Bits
Table 9. Status Bit Functions
Bit Name
RDY
FILTER
ERR
ID1, ID0
GAIN
PAT1, PAT0
Description
Ready bit.
0: a conversion is available.
Filter bit.
1: 10 Hz filter is selected
0: 16.7 Hz filter is selected.
Error bit.
1: an error occurred during conversion. (An error occurs when the analog input is outside the range.)
ID bits.
ID1
ID0
Function
0
1
Indicates the ID number for the AD7780
Gain bit.
1: gain = 1.
0: gain = 128.
Status pattern bits. When the user reads data from the AD7780, a pattern check can be performed.
PAT1
PAT0
Function
0
1
Indicates that the serial transfer from the ADC was performed correctly (default).
0
0
Indicates that the serial transfer from the ADC was not performed correctly.
1
0
Indicates that the serial transfer from the ADC was not performed correctly.
1
1
Indicates that the serial transfer from the ADC was not performed correctly.
Rev. A | Page 13 of 16
AD7780
APPLICATIONS INFORMATION
The AD7780 provides a low cost, high resolution analog-to-digital
function. Because the analog-to-digital function is provided by a
Σ-Δ architecture, the parts are more immune to noisy environments, making them ideal for use in sensor measurement and
industrial and process control applications.
no load is applied to the load cell) and the full-scale error (the
conversion result from the ADC when the maximum load is
applied to the load cell) must be determined. Subsequent conversions from the AD7780 are then corrected, using the offset and
gain coefficients that were calculated from these calibrations.
WEIGH SCALES
PERFORMANCE IN A WEIGH SCALE SYSTEM
Figure 23 shows the AD7780 being used in a weigh scale
application. The load cell is arranged in a bridge network and
gives a differential output voltage between its OUT+ and OUT−
terminals. Assuming a 5 V excitation voltage, the full-scale
output range from the transducer is 10 mV when the sensitivity
is 2 mV/V. The excitation voltage for the bridge can be used to
directly provide the reference for the ADC because the reference input range includes the supply voltage.
If the load cell has a sensitivity of 2 mV/V and a 5 V excitation
voltage is used, the full-scale signal from the load cell is 10 mV.
When the AD7780 operates with a 10 Hz output data rate and
the gain is set to 128, the device has a p-p resolution of 18.2 bits
when the reference is equal to 5 V. Postprocessing the data from
the AD7780 using a microprocessor increases the p-p resolution.
For example, an average by 4 in the microprocessor increases
the accuracy by 2 bits. The noise-free counts is equal to the
following:
A second advantage of using the AD7780 in transducer-based
applications is that the bridge power-down switch (BPDSW)
can be fully utilized in low power applications. The bridge powerdown switch is connected in series with the low side of the bridge.
In normal operation, the switch is closed and measurements
can be taken. In applications where power is of concern, the
AD7780 can be placed in power-down mode, significantly
reducing the power consumed in the application. In addition,
the bridge power-down switch is opened while in power-down
mode, thus avoiding unnecessary power consumption by the
front-end transducer. When the part is taken out of power-down
mode and the bridge power-down switch is closed, the user should
ensure that the front-end circuitry is fully settled before attempting
a read from the AD7780.
Noise-Free Counts = (2Effective Bits)(FSLC/FSADC)
where:
Effective Bits = 18.2 bits + 2 bits (due to post-processing in the
microprocessor).
FSLC is the full-scale signal from the load cell (10 mV).
FSADC is the full-scale input range when gain = 128 and VREF = 5 V
(78 mV).
The noise-free counts are equal to the following:
(218.2 + 2)(10 mV/78 mV) = 154,422
This example shows that with a 5 V supply, 154,422 noise-free
counts can be achieved with the AD7780.
EMI RECOMMENDATIONS
The load cell has an offset or tare associated with it. This tare is
the main component of the system offset (load cell + ADC) and is
similar in magnitude to the full-scale signal from the load cell.
For this reason, calibrating the offset and gain of the AD7780 alone
is not sufficient for optimum accuracy; a system calibration that
calibrates the offset and gain of the ADC, plus the load cell, is
required. A microprocessor can be used to perform the calibrations. The offset (the conversion result from the AD7780 when
For simplicity, the EMI filters are not included in Figure 23.
However, an R-C antialiasing filter should be included on each
analog input. This filter is needed because the on-chip digital
filter does not provide any rejection around the master clock or
multiples of the master clock. Suitable values are a 1 kΩ resistor
in series with each analog input, a 0.1 μF capacitor from AIN(+)
to AIN(−), and 0.01 μF capacitors from AIN(+)/AIN(−) to GND.
VDD
IN+
GND
REFIN(+)
OUT+
IN–
AIN(+)
AIN(–)
REFIN(–)
DOUT/RDY
G=1
OR 128
24-BIT Σ-Δ
ADC
SCLK
INTERNAL
CLOCK
BPDSW
DVDD
FILTER
PDRST
AD7780
Figure 23. Weigh Scales Using the AD7780
Rev. A | Page 14 of 16
GAIN
07945-022
OUT–
AVDD
AD7780
GROUNDING AND LAYOUT
Because the analog input and reference input of the ADC are
differential, most of the voltages in the analog modulator are
common-mode voltages. The excellent common-mode rejecttion of the part removes common-mode noise on these inputs.
The digital filter provides rejection of broadband noise on the
power supply, except at integer multiples of the modulator sampling frequency. The digital filter also removes noise from the
analog and reference inputs, provided that these noise sources
do not saturate the analog modulator. As a result, the AD7780
is more immune to noise interference than conventional high
resolution converters. However, because the resolution of the
AD7780 is so high, and the noise levels from the AD7780 are so
low, care must be taken with regard to grounding and layout.
The printed circuit board that houses the AD7780 should be
designed such that the analog and digital sections are separated
and confined to certain areas of the board. A minimum etch
technique is generally best for ground planes because it gives
the best shielding.
It is recommended that the GND pin of the AD7780 be tied
to the AGND plane of the system. In any layout, pay attention
to the flow of currents in the system and ensure that the return
paths for all currents are as close as possible to the paths that the
currents took to reach their destinations. Avoid forcing digital
currents to flow through the AGND sections of the layout.
The ground plane of the AD7780 should be allowed to run under
the AD7780 to prevent noise coupling. The power supply lines
to the AD7780 should use as wide a trace as possible to provide
low impedance paths and reduce the effects of glitches on the
power supply line. Fast switching signals such as clocks should
be shielded with digital ground to avoid radiating noise to other
sections of the board, and clock signals should never be run near
the analog inputs. Avoid crossover of digital and analog signals.
Traces on opposite sides of the board should run at right angles
to each other. This reduces the effects of feedthrough through
the board. A microstrip technique is by far the best, but it is not
always possible with a double-sided board. In this technique,
the component side of the board is dedicated to ground planes,
and the signals are placed on the solder side.
Good decoupling is important when using high resolution
ADCs. AVDD should be decoupled with 10 μF tantalum capacitors in parallel with 0.1 μF capacitors to GND. DVDD should
be decoupled with 10 μF tantalum capacitors in parallel with
0.1 μF capacitors to GND, with the system’s AGND to DGND
connection kept close to the AD7780. To achieve the best results
from these decoupling components, place them as close as possible
to the device, ideally right up against the device. All logic chips
should be decoupled with 0.1 μF ceramic capacitors to DGND.
Rev. A | Page 15 of 16
AD7780
OUTLINE DIMENSIONS
8.75 (0.3445)
8.55 (0.3366)
4.00 (0.1575)
3.80 (0.1496)
8
14
1
6.20 (0.2441)
5.80 (0.2283)
7
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
0.10
0.50 (0.0197)
0.25 (0.0098)
1.75 (0.0689)
1.35 (0.0531)
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
060606-A
COMPLIANT TO JEDEC STANDARDS MS-012-AB
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 24. 14-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-14)
Dimensions shown in millimeters and (inches)
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.30
0.19
0.65
BSC
COPLANARITY
0.10
0.20
0.09
8°
0°
SEATING
PLANE
0.75
0.60
0.45
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 25. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD7780BRZ 1
AD7780BRZ-REEL1
AD7780BRUZ1
AD7780BRUZ-REEL1
1
Temperature Range
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
Package Description
14-Lead SOIC_N
14-Lead SOIC_N
16-Lead TSSOP
16-Lead TSSOP
Z = RoHS Compliant Part.
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07945-0-9/09(A)
Rev. A | Page 16 of 16
Package Option
R-14
R-14
RU-16
RU-16
Similar pages