Murata DLW5BSM191SQ2 Common mode choke coil wire wound type for large current Datasheet

Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type for Large Current
Data Sheet
1
Common Mode Choke Coil Wire Wound Type for Large Current
DLW5AH/DLW5BS Series (2014/2020 Size)
c Dimensions
c Dimensions
DLW5AH Series
DLW5BS Series
3.0±0.5
0.5±0.3
0.45 min.
*
*
(T) 4.3 max.
(Top)
0.5 min.
(W) 3.6±0.3
: Electrode
(3)
1.7±0.3
(4)
1.3 0.9 1.3
±0.3 ±0.3 ±0.3
(in mm)
c Impedance-Frequency Characteristics (Main Items)
1.3±0.3
(4)
0.5 min.
0.45 min.
3.6±0.3
(W) 5.0±0.3
(1)
(2)
(L) 5.0±0.3
1.3±0.3
1.7 1.3 1.7
±0.3 ±0.3 ±0.3
position of wiring should
* Starting
be covered with resin.
(Bottom)
(T) 4.5 max.
(2)
1.7±0.3
(1)
(L) 5.0±0.3
: Marking
: Electrode
(3) 1.3±0.3
0.9±0.3
(in mm)
c Equivalent Circuit
100000
Impedance (Ω)
10000
DLW5AHN402SQ2
DLW5BSM302SQ2
DLW5BSM152SQ2
DLW5BSM102SQ2
DLW5BSM351SQ2
DLW5BSM191SQ2
1000
(1)
(2)
(4)
(3)
Common mode
100
DLW5AHN402SQ2
DLW5BSM302SQ2
DLW5BSM152SQ2
Differential mode
DLW5BSM102SQ2
DLW5BSM351SQ2
DLW5BSM191SQ2
No polarity.
10
1
10
100
1000
Frequency (MHz)
c Packaging
Code
Packaging
L
180mm Embossed Tape
Minimum Quantity
400
K
330mm Embossed Tape
1500
B
Bulk(Bag)
100
c Rated Value (p: packaging code)
Operating
Temperature Range
Part Number
Common Mode Impedance
(at 100MHz/20°C)
DLW5AHN402SQ2p
4000ohm (Typ.)
200mA
50Vdc
10M ohm
125Vdc
3.0ohm max.
-25 to +85°C
DLW5BSM191SQ2p
190ohm (Typ.)
5000mA
50Vdc
10M ohm
125Vdc
0.02ohm max.
-40 to +85°C
Rated Current Rated Voltage Insulation Resistance (min.)
Withstand Voltage DC Resistance
DLW5BSM351SQ2p
350ohm (Typ.)
2000mA
50Vdc
10M ohm
125Vdc
0.04ohm max.
-40 to +85°C
DLW5BSM102SQ2p
1000ohm (Typ.)
1500mA
50Vdc
10M ohm
125Vdc
0.06ohm max.
-40 to +85°C
DLW5BSM152SQ2p
1500ohm (Typ.)
1000mA
50Vdc
10M ohm
125Vdc
0.1ohm max.
-40 to +85°C
DLW5BSM302SQ2p
3000ohm (Typ.)
500mA
50Vdc
10M ohm
125Vdc
0.3ohm max.
-40 to +85°C
Number of Circuit: 1
Continued on the following page.
oThis data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design.
!Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it
may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2012.7.5
http://www.murata.com/
Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type for Large Current
Data Sheet
2
Continued from the preceding page.
c Derating of Rated Current
In operating temperature exceeding +75°C,
derating of current is necessary for
DLW5BSM191SQ2 series.
Please apply the derating curve shown in
chart according to the operating
temperature.
Derating of Rated Current
5
Rated Current (A)
DLW5BSM191SQ2
4.75
4.5
0
10
20
30
40
50
60
70 80 90 100
75°C 85°C
Operating Temperature (°C)
c !Caution/Notice
!Caution (Rating)
Do not use products beyond the rated current and
rated voltage as this may create excessive heat
and deteriorate the insulation resistance.
Notice
Solderability of Tin plating termination chip might be
deteriorated when low temperature soldering profile
where peak solder temperature is below the Tin melting
point is used. Please confirm the solderability of Tin
plating termination chip before use.
oThis data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design.
!Note:
1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it
may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
specifications or transact the approval sheet for product specifications before ordering.
2012.7.5
http://www.murata.com/
Similar pages