CHEMI-CON APS-2R5ESS152MJC5S Conductive polymer aluminum solid capacitor Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
@Super low ESR, high temperature resistance
@Large capacitance & Improved high ripple current capability
@Rated voltage range : 2.5 to 25Vdc
@2000 hours at 105C
@Suitable for DC-DC converters, voltage regulators and decoupling applications
For computer motherboards
@Pb-free design
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-55 to +105C
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
2.5 to 25Vdc
P20% (M)
Rated voltageB1.15V
I=0.2CV (max.)
Where, I : Leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc)
Dissipation Factor
(tane)
0.12 max.
Low Temperature
Characteristics
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
(at 20C, 120Hz)
Max. impedance ratio at 100kHz to the 20C value
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours
at 105C.
Appearance
No significant damage
Capacitance change
[P20% of the initial measured value
D.F. (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C,
90 to 95% RH for 500 hours.
Appearance
No significant damage
Capacitance change
[P20% of the initial measured value
D.F. (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
[P20% of the initial measured value
D.F. (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
1% per 1000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105C.
?DIMENSIONS [mm]
?MARKING
@Terminal Code : E
FP0.5
EX) 4V820MF
F0.6
FD+0.5max.
Coated Case
PS18M
820
4V
fD
L
F
L+1.5 max.
15min.
8
11.5
3.5
10
12.5
5.0
4min.
(1/2)
CAT. No. E1001E
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
?PART NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
A PS- AAA E AA AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 270MF:271,1500MF:152)
Lead forming·Taping code
Terminal code
Voltage code (ex. 4V:4R0,6.3V:6R3,10V:100)
Series code
Category
Please refer to "A guide to global code (conductive polymer type)"
?STANDARD RATINGS
WV(Vdc)
2.5
4
6.3
10
16
20
25
Cap(µF)
680
1500
560
820
390
680
270
470
180
330
100
150
68
100
Case size
fDbL(mm)
ESR
(momax/20c, 100k to 300kHz)
Rated ripple current
(mArms/105c, 100kHz)
8B11.5
10B12.5
8B11.5
10B12.5
8B11.5
10B12.5
8B11.5
10B12.5
8B11.5
10B12.5
8B11.5
10B12.5
8B11.5
10B12.5
10
8
10
8
12
10
14
12
16
14
24
20
24
20
5230
5500
5230
5500
4770
5500
4420
5300
4360
5050
3320
4320
3320
4320
Part No.
APS-2R5ESS681MHB5S
APS-2R5ESS152MJC5S
APS-4R0ESS561MHB5S
APS-4R0ESS821MJC5S
APS-6R3ESS391MHB5S
APS-6R3ESS681MJC5S
APS-100ESS271MHB5S
APS-100ESS471MJC5S
APS-160ESS181MHB5S
APS-160ESS331MJC5S
APS-200ESS101MHB5S
APS-200ESS151MJC5S
APS-250ESS680MHB5S
APS-250ESS101MJC5S
SS : Lead forming code and taping code
(2/2)
CAT. No. E1001E
Similar pages