Fujitsu MZ-12WHS-K Miniature relay 1 pole-1 to 2 a (for signal switching) Datasheet

MINIATURE RELAY
1 POLE—1 to 2 A (FOR SIGNAL SWITCHING)
MZ SERIES
RoHS compliant
n FEATURES
l
l
l
l
l
l
l
l
Subminiature size
Standard and high sensitivity types available
UL, CSA recognized
FCC rules and regulations part 68
—Dielectric strength 1,500 V between coil and contacts
High reliability-bifurcated contacts available
DIL pitch terminals
Plastic sealed type
RoHS compliant since date code: 0437L2
Please see page 6 for more information
n ORDERING INFORMATION
[Example]
MZ F – 12
(a) (b) (c)
(a)
Series Name
(b)
Dielectric Function
(c)
Nominal Voltage
W
(d)
HG – K – U
(e) (f ) (g)
MZ : MZ Series
Nil : Standard type
F : High dielectric strength type
Refer to the COIL DATA CHART
(d)
Contact
Nil : 1 A single
D : 2 A single (without MZF)
W : 1 A bifurcated type
(e)
Coil Type
HG : Standard type (without MZ-D) (450-500mW)
HS : High sensitivity type (without MZF/MZ-D) (190-270mW)
(f )
Enclosure
Nil : Flux free type
K : Plastic sealed type
(g)
UL, CSA Standard
Nil : Non UL, • CSA approved type
U : UL • CSA approved type
Note: For movable and stationary contact with gold overlay type, add suffix “–OH”.
1
MZ SERIES
n COIL DATA CHART
MODEL
Nominal
Single
Bifurcated
voltage
1 A Type
1 A Type
Must
operate
voltage
Must
release
voltage
Nominal
power
MZ (F)-1.5HG-(K)
MZ-1.5WHG-(K)
1.5 VDC
5Ω
1.05 VDC
0.08 VDC
450 mW
MZ- 3 D-(K)
MZ (F)- 3 HG-(K)
MZ- 3 WHG-(K)
3 VDC
20 Ω
2.1 VDC
0.15 VDC
450 mW
MZ-4.5D-(K)
MZ (F)-4.5HG-(K)
MZ-4.5WHG-(K)
4.5 VDC
45 Ω
3.15 VDC
0.23 VDC
450 mW
MZ- 5 D-(K)
MZ (F)- 5 HG-(K)
MZ- 5 WHG-(K)
5 VDC
56 Ω
3.5 VDC
0.25 VDC
450 mW
MZ- 6 D-(K)
MZ (F)- 6 HG-(K)
MZ- 6 WHG-(K)
6 VDC
80 Ω
4.2 VDC
0.3 VDC
450 mW
MZ- 9 D-(K)
MZ (F)- 9 HG-(K)
MZ- 9 WHG-(K)
9 VDC
180 Ω
6.3 VDC
0.45 VDC
450 mW
MZ-12 D-(K)
MZ (F)-12 HG-(K)
MZ-12 WHG-(K)
12 VDC
320 Ω
8.4 VDC
0.6 VDC
450 mW
MZ-18 D-(K)
MZ (F)-18 HG-(K)
MZ-18 WHG-(K)
18 VDC
720 Ω
12.6 VDC
0.9 VDC
450 mW
MZ-24 D-(K)
MZ (F)-24 HG-(K)
MZ-24 WHG-(K)
24 VDC
1,280 Ω
16.8 VDC
1.2 VDC
450 mW
MZ-48 D-(K)
MZ (F)-48 HG-(K)
MZ-48 WHG-(K)
48 VDC
4,600 Ω
33.6 VDC
2.4 VDC
500 mW
MZ-1.5HS-(K)
MZ-1.5WHS-(K)
1.5 VDC
12 Ω
1.05 VDC
0.08 VDC
190 mW
MZ- 3 HS-(K)
MZ- 3 WHS-(K)
3 VDC
45 Ω
2.1 VDC
0.15 VDC
200 mW
MZ-4.5HS-(K)
MZ-4.5WHS-(K)
4.5 VDC
100 Ω
3.15 VDC
0.23 VDC
200 mW
MZ- 5 HS-(K)
MZ- 5 WHS-(K)
5 VDC
120 Ω
3.5 VDC
0.25 VDC
200 mW
MZ- 6 HS-(K)
MZ- 6 WHS-(K)
6 VDC
180 Ω
4.2 VDC
0.3 VDC
200 mW
MZ- 9 HS-(K)
MZ- 9 WHS-(K)
9 VDC
400 Ω
6.3 VDC
0.45 VDC
200 mW
MZ-12 HS-(K)
MZ-12 WHS-(K)
12 VDC
700 Ω
8.4 VDC
0.6 VDC
200 mW
MZ-15 HS-(K)
MZ-15 WHS-(K)
15 VDC
1,100 Ω
10.5 VDC
0.75 VDC
200 mW
MZ-18 HS-(K)
MZ-18 WHS-(K)
18 VDC
1,600 Ω
12.6 VDC
0.9 VDC
200 mW
MZ-24 HS-(K)
MZ-24 WHS-(K)
24 VDC
2,800 Ω
16.8 VDC
1.2 VDC
200 mW
MZ-48 HS-(K)
MZ-48 WHS-(K)
48 VDC
8,500 Ω
33.6 VDC
2.4 VDC
270 mW
Standard Type
MZ-1.5D-(K)
High Sensitivity Type
2 A Type
Coil
resistance
(±10%)
Note: All values in the table are measured at 20°C.
MZ SERIES
n SPECIFICATIONS
Standard
Item
Contact
Arrangement
Single
MZ-( ) D
High Sensitivity Type
Bifurcated
Single
MZ-( ) HG MZ-( ) WHG
Bifurcated
MZ-( ) HS MZ-( ) WHS
1 form C (SPDT)
Material
Gold-overlay
silver-nickel
Resistance (initial)
Maximum 100 mΩ (at 1 A 6 VDC)
Rating (resistive)
2 A 24 VDC
1 A 120 VAC
Maximum Carrying Current
2A
Maximum Switching Power
120 VA/48 W
Maximum Switching Voltage
120 VAC, 60 VDC
Maximum Switching Current
2A
Minimum Switching Load*
1 mA 1 VDC
Capacitance
(at 10 MHz)
Approximately 0.8 pF (between open contacts, adjacent contacts)
Approximately 7.5 pF (between coil and contacts)
Coil
Nominal Power (at 20°C)
450 to 500 mW
190 to 270 mW
Operate Power (at 20°C)
220 to 250 mW
100 to 130 mW
Operating Temperature
–30°C to +55°C (no frost)
–30°C to +75°C Operate (at nominal voltage)
Maximum 6 ms
Release (at nominal voltage)
Maximum 3 ms
Mechanical
2 × 107 operations minimum
Time Value
Life
Electrical (at rating)
Other
Gold overlay silver-palladium
1 A 24 VDC
0.5 A 120 VAC
60 AV/24 W
1A
0.1 mA 100 mVDC
1 mA 1 VDC 0.1 mA 100 mVDC
1 A 120 VAC
0.5 A 120 VAC 2 × 105 operations minimum
1 × 105 ops. min. 1 A 24 VAC 5 × 105 operations minimum
2 A 24 VDC
2 × 105 ops. min.
Vibration
Misoperation
Resistance Endurance
10 to 55 Hz (double amplitude of 3.28 mm)
Shock
Misoperation
Resistance Endurance
100 m/s2 (11±1 ms)
Weight
Approximately 3.5 g
10 to 55 Hz (double amplitude of 3.28 mm)
1,000 m/s2 ( 6±1 ms)
*1 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with the actual load
before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels.
MZ SERIES
n INSULATION
Item
Single
Isolation (initial)
Minimum 100 MΩ (at 500VDC)
Dielectric
Strength
open contacts
Standard: 500VAC 1 min., High isolation: 1,000VAC 1 min.
coil and contacts
Standard: 500VAC 1 min., High isolation: 1,500VAC 1 min.
Surge Voltage
1500V (coil-contact) (1/40 µs standard wave)
n SAFETY STANDARDS AND FILE NUMBERS
Type
Compliance
Contact rating
UL
UL 508
UL 60950-1
E 45026
CSA
C22.2 No. 14
LR 35579
Flammability: UL 94-V0 (plastics)
[1A]
0.5A, 120VAC (resistive)
1A, 24VDC (resistive)
[2A]
1A, 120VAC (resistive)
2A, 30VDC (resistive)
n CHARACTERISTIC DATA
0.1
0.3
0.5
MZ SERIES
n REFERENCE DATA
MZ SERIES
n DIMENSIONS
l Dimensions
MZ (F) type (Flux free type)
l Schematics
(Bottom View)
l
PC board mounting
hole layout
(Bottom View)
MZ (F)-K type (Plastic sealed type)
Unit: mm
MZ SERIES
RoHS Compliance and Lead Free Relay Information
1. General Information
Relays produced after the specific date code that is indicated on each data sheet are lead-free
now. Most of our signal and power relays are lead-free. Please refer to Lead-Free Status Info.
(http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf)
l
Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu.
l
All signal and most power relays also comply with RoHS. Please refer to individual data
sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that
are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE).
l
It has been verified that using lead-free relays in leaded assembly process will not cause any
problems (compatible).
l
“LF” is marked on each outer and inner carton. (No marking on individual relays).
l
To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l
We will ship leaded relays as long as the leaded relay inventory exists.
Note: Cadmium was exempted from RoHS on October 21, 2005. (Amendment to Directive 2002/95/EC)
l
2. Recommended Lead Free Solder Profile
l
Recommended solder paste Sn-3.0Ag-0.5Cu.
Reflow Solder condition
Flow Solder condition:
Pre-heating:
Soldering:
maximum 120˚C
dip within 5 sec. at
260˚C soler bath
Solder by Soldering Iron:
Soldering Iron
Temperature: maximum 360˚C
Duration:
maximum 3 sec.
We highly recommend that you confirm your actual solder conditions
3. Moisture Sensitivity
l
Moisture Sensitivity Level standard is not applicable to electromechanical realys.
4. Tin Whisker
l
Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in
house test.
MZ SERIES
Fujitsu Components International Headquarter Offices
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Web: www.fcl.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Web: emea.fujitsu.com/components/
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: [email protected]
Web: http://www.fujitsu.com/us/services/edevices/components/
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#01-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: [email protected]
Web: http://www.fujitsu.com/sg/services/micro/components/
©2008 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective
owners.
Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our
products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice.
Rev. January 9, 2008.
Similar pages