ATMEL AT27C520-70SC 512k 64k x 8 multiplexed addresses/ outputs otp eprom Datasheet

Features
• 8-Bit Multiplexed Addresses/Outputs
• Fast Read Access Time - 70 ns
• Low Power CMOS Operation
•
•
•
•
•
•
•
•
•
– 20 mA max. Active at 5 MHz
20-Lead TSSOP Package
20-Lead SOIC Package
28-Lead TSOP Package
5V ± 10% Supply
High Reliability CMOS Technology
– 2,000V ESD Protection
– 200 mA Latchup Immunity
Rapid™ Programming Algorithm - 50 µs/byte (typical)
CMOS and TTL Compatible Inputs and Outputs
Integrated Product Identification Code
Commercial and Industrial Temperature Range
Description
The AT27C520 is a low-power, high performance 524,288 bit one-time programmable
read only memory (OTP EPROM) organized 64K by 8 bits. It incorporates latches for
the 8 lower order address bits to multiplex with the 8 data bits. This minimizes system
chip count, reduces cost, and simplifies the design of multiplexed bus systems. It
requires only one 5V power supply in normal read mode operation. Any byte can be
accessed in less than 70 ns, eliminating the need for speed reducing WAIT states on
high performance microprocessor systems.
Atmel’s scaled CMOS technology provides high speed, lower active power consumption, and significantly faster programming. Power consumption is typically only 8 mA
in Active Mode.
The AT27C520 is available in 173 mil, 20-pin TSSOP; 300 mil, 20-pin SOIC; and 28pin TSOP, one-time programmable (OTP) plastic packages.
(continued)
Pin Configurations
512K (64K x 8)
Multiplexed
Addresses/
Outputs
OTP EPROM
AT27C520
TSSOP Top View
Pin Name
Function
A8 - A15
Addresses
AD0 - AD7
Addresses/Outputs
OE /VPP
Output Enable/VPP
ALE
Address Latch Enable
A10
A12
A14
ALE
VCC
OE/VPP
A15
A13
A11
A9
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
A8
AD1
AD3
AD5
AD7
GND
AD6
AD4
AD2
AD0
TSOP Top View
A10
NC
NC
A12
A14
ALE
VCC
OE/VPP
A15
A13
A11
NC
NC
A9
22
23
24
25
26
27
28
1
2
3
4
5
6
7
21
20
19
18
17
16
15
14
13
12
11
10
9
8
A8
NC
NC
AD1
AD3
AD5
AD7
GND
AD6
AD4
AD2
NC
NC
AD0
SOIC Top View
OE/VPP
A15
A13
A11
A9
AD0
AD2
AD4
AD6
GND
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
VCC
ALE
A14
A12
A10
A8
AD1
AD3
AD5
AD7
Rev. 0752C-C–01/98
1
With 64K byte storage capability, the AT27C520 allows
firmware to be stored reliably and to be accessed by the
system without the delays of mass storage media.
Atmel's 27C520 has additional features to ensure high
quality and efficient production use. The Rapid™ Programming Algorithm reduces the time required to program the
part and guarantees reliable programming. Programming
time is typically only 50 µs/byte. The Integrated Product
Identification Code electronically identifies the device and
manufacturer. This feature is used by industry standard
programming equipment to select the proper programming
algorithms and voltages.
System Considerations
Switching under active conditions may produce transient
voltage excursions. Unless accommodated by the system
design, these transients may exceed data sheet limits,
resulting in device non-conformance. At a minimum, a 0.1
µF high frequency, low inherent inductance, ceramic
capacitor should be utilized for each device. This capacitor
should be connected between the VCC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again connected
between the V CC and Ground terminals. This capacitor
should be positioned as close as possible to the point
where the power supply is connected to the array.
Block Diagram
VCC
GND
AD7 - AD0
A15 - A8
OE, ALE, AND
PROGRAM LOGIC
LATCHES
OE/VPP
ALE
8
8
OUTPUT
BUFFERS
Y DECODER
Y-GATING
X DECODER
CELL MATRIX
IDENTIFICATION
2
AT27C520
AT27C520
Absolute Maximum Ratings*
Temperature Under Bias ................................ -55°C to +125°C
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Note:
Minimum voltage is -0.6V DC which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V DC
which may overshoot to +7.0V for pulses of less
than 20 ns.
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin with
Respect to Ground .........................................-2.0V to +7.0V(1)
Voltage on A9 with
Respect to Ground ......................................-2.0V to +14.0V(1)
1.
VPP Supply Voltage with
Respect to Ground .......................................-2.0V to +14.0V(1)
Operating Modes
Mode/Pin
Read
Output Disable
Address Latch Enable
Rapid Program
(2)
Product Identification
Notes:
(3)
ALE
OE/VPP
A8 - A15
AD0 - AD7
VIL
VIL
Ai
DOUT
VIL/VIH
VIH
VIH
VIH
X
A0 - A7
VIH
VPP
Ai
DIN
VIL
A9 = VH(4)
A8 = VIH or VIL
A10 - A15 = VIL
Identification Code
VIL
X
(1)
High Z/A0 - A7
1. X can be VIL or VIH.
2. Refer to Programming Characteristics.
3. VH = 12.0 ± 0.5V.
4. Two identifier bytes may be selected. All A8 - A15 inputs are held low (VIL), except A9 which is set to VH and A8 which is
toggled low (VIL) to select the Manufacturer’s Identification byte and high (VIH) to select the Device Code byte.
3
DC and AC Operating Conditions for Read Operation
AT27C520
-70
-90
0°C - 70°C
0°C - 70°C
-40°C - 85°C
-40°C - 85°C
5V ± 10%
5V ± 10%
Com.
Operating Temp.(Case)
Ind.
VCC Supply
DC and Operating Characteristics for Read Operation
Symbol
Parameter
Condition
ILI
Max
Units
Input Load Current
VIN = 0V to VCC
±1
µA
Input Load Current A13
VIN = 0V to VCC
±100
µA
ILO
Output Leakage Current
VOUT = 0V to VCC
±5
µA
ICC
VCC Active Current
f = 5 MHz, IOUT = 0 mA
20
mA
VIL
Input Low Voltage
-0.6
0.8
V
VIH
Input High Voltage
2.0
VCC + 0.5
V
VOL
Output Low Voltage
IOL = 2.1 mA
0.4
V
VOH
Output High Voltage
IOH = -400 µA
ILI2
(1)
Note:
Min
2.4
V
1. For address input A13 only.
AC Characteristics for Read Operation
AT27C520
-70
Symbol
Parameter
Condition
tACC(2)
Address to Output Delay
ALE = OE/VPP = VIL
tAS
Address Setup Time
OE/VPP = VIH
12
15
ns
tAH
Address Hold Time
OE/VPP = VIH
12
15
ns
tALE
Address Latch Enable Width
OE/VPP = VIH
40
45
ns
tOE(2)
OE/VPP to Output Delay
ALE = VIL
30
35
ns
tDF(3)(4)
OE/VPP High to Output Float
ALE = VIL
25
25
ns
tOH
Output Hold from Address or
OE/VPP , whichever occurred first
ALE = VIL
Notes:
4
-90
1. 2, 3, 4 — see AC Waveforms for Read Operation
AT27C520
Min
Max
Min
70
7
0
Max
Units
90
ns
ns
AT27C520
AC Waveforms for Read Operation(1)
tALE
ALE
OE/VPP
tDF
tAS
AD7 - AD0
tAH
ADDRESS IN
tOE
tOH
DATA OUT
tACC
A15 - A8
Notes:
1.
Timing measurement reference levels for all speed grades are VOL = 0.8V and VOH = 2.0V. Input AC drive levels are VIL =
0.45V and VIH = 2.4V.
2.
OE/VPP may be delayed up to tACC - tOE after the address is valid without impact on tACC.
3.
This parameter is only sampled and is not 100% tested.
4.
Output float is defined as the point when data is no longer driven.
Input Test Waveforms and Measurement Levels
Output Test Load
For -70 and -90 devices:
tR, tF < 20 ns (10% to 90%)
Note:
CL = 100 pF including jig
capacitance.
Pin Capacitance (f = 1 MHz, T = 25°C)(1)
CIN
COUT
Note:
Typ
Max
Units
Conditions
4
6
pF
VIN = 0V
8
12
pF
VOUT = 0V
1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.
5
Programming Waveforms
PROGRAM
VCC
READ (VERIFY)
6.5V
5.0V
tVCS
13V
OE/VPP
VIH
VIL
tOES tOEH
tPRT
ALE
tVR
tLP
VIH
VIL
tALE
tALE
tPW
tOE
AD7 - AD0
VIH
VIL
A15 - A8
VIH
VIL
tLAS
tLAH
ADDR
tDS
DATA IN
tDH
tLAS
tDFP
tLAH
ADDR
DATA OUT
tAS
Notes:
tAH
ADDRESS STABLE
1.
The Input Timing Reference is 0.8V for VIL and 2.0V for VIH.
2.
tOE and tDFP are characteristics of the device but must be accommodated by the programmer.
DC Programming Characteristics
TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, OE/VPP = 13.0 ± 0.25V
Limits
Symbol
Parameter
Test Conditions
ILI
Input Load Current
Input Load Current A13
ILI2
(1)
Max
Units
VIN = VIL, VIH
±10
µA
VIN = VIL, VIH
±100
µA
VIL
Input Low Level
-0.6
0.8
V
VIH
Input High Level
2.0
VCC + 1.0
V
VOL
Output Low Voltage
IOL = 2.1 mA
0.4
V
VOH
Output High Voltage
IOH = -400 µA
ICC2
VCC Supply Current (Program and Verify)
IPP2
OE/VPP Current
Note:
6
Min
1. For address input A13 only.
AT27C520
ALE = VIH
2.4
V
25
mA
25
mA
AT27C520
AC Programming Characteristics
TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, OE/VPP = 13.0 ± 0.25V
Limits
(1)
Test Conditions
Min
Max
Units
Symbol
Parameter
tALE
Address Latch Enable Width
500
ns
tLAS
Latched Address Setup Time
100
ns
tLAH
Latched Address Hold Time
100
ns
tLP
ALE Low to OE/VPP High Voltage Delay
2
µs
2
µs
2
µs
2
µs
2
µs
tOES
OE/VPP Setup Time
tOEH
OE/VPP Hold Time
tDS
Data Setup Time
Input Rise and Fall Times
(10% to 90%) 20 ns
Input Pulse Levels
0.45V to 2.4V
tDH
Data Hold Time
tPW
ALE Program Pulse Width(2)
tVR
OE/VPP Recovery Time
tVCS
VCC Setup Time
tOE
Data Valid from OE/VPP
tDFP
OE/VPP High to Output Float Delay(3)
0
tAS
Address Setup Time
2
µs
tAH
Address Hold Time
0
µs
tPRT
OE/VPP Pulse Rise Time During Programming
50
ns
Notes:
Input Timing Reference Level
0.8V to 2.0V
47.5
52.5
µs
2
µs
2
µs
Output Timing Reference Level
0.8V to 2.0V
150
ns
130
ns
1. VCC must be applied simultaneously or before OE/VPP and removed simultaneously or after OE/VPP.
2. Program Pulse width tolerance is 50 µsec ± 5%.
3. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven
— see timing diagram.
Atmel’s 27C520 Integrated Product Identification Code
Pins
A8
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
Hex
Data
Manufacturer
0
0
0
0
1
1
1
1
0
1E
Device Type
1
1
0
0
1
1
1
0
1
9D
Codes
7
Rapid™ Programming Algorithm
A 50 µs ALE pulse width is used to program. The address
is set to the first location. VCC is raised to 6.5V and OE/VPP
is raised to 13.0V. Each address is first programmed with
one 50 µs ALE pulse without verification. Then a verification/reprogramming loop is executed for each address. In
the event a byte fails to pass verification, up to 10 successive 50 µs pulses are applied with a verification after each
pulse. If the byte fails to verify after 10 pulses have been
applied, the part is considered failed. After the byte verifies
properly, the next address is selected until all have been
checked. OE/VPP is then lowered to VIH and VCC to 5.0V. All
bytes are read again and compared with the original data to
determine if the device passes or fails.
START
ADDR = FIRST LOCATION
VCC = 6.5V
VPP = 13.0V
PROGRAM ONE 50 µS PULSE
INCREMENT
ADDRESS
NO
LAST
ADDR.?
YES
ADDR = FIRST LOCATION
INCREMENT
ADDRESS
X=0
NO
LAST
ADDR.?
PASS
VERIFY
BYTE
FAIL
INCREMENT X
YES
PROGRAM ONE 100 µS PULSE
NO
X = 10?
YES
VCC = 5.0V
VPP = 5.0V
COMPARE
ALL BYTES
TO ORIGINAL
DATA
PASS
DEVICE
PASSED
8
AT27C520
FAIL
DEVICE
FAILED
AT27C520
Ordering Information
tACC (ns)
ICC (mA)
Active
70
20
90
20
Ordering Code
Package
AT27C520-70SC
AT27C520-70TC
AT27C520-70XC
20S
28T
20X
Operation Range
Commercial
(0°C to 70°C)
AT27C520-70SI
AT27C520-70TI
AT27C520-70XI
20S
28T
20X
Industrial
(-40°C to 85°C)
AT27C520-90SC
AT27C520-90TC
AT27C520-90XC
20S
28T
20X
Commercial
(0°C to 70°C)
AT27C520-90SI
AT27C520-90TI
AT27C520-90XI
20S
28T
20X
Industrial
(-40°C to 85°C)
Package Type
20S
20-Lead, 0.300” Wide, Plastic Gull-Wing Small Outline (SOIC)
28T
28-Lead, Thin Small Outline Package (TSOP)
20X
20-Lead, 0.173” Wide, Thin Shrink Small Outline (TSSOP)
9
Packaging Information
20S, 20-Lead, 0.300” Wide,
Plastic Gull Wing Small Outline
Dimensions in Inches and (Millimeters)
28T, 28-Lead, Plastic Thin Small Outline Package
(TSOP)
Dimensions in Millimeters and (Inches)
.020(.508)
.013(.330)
.299(7.60) .420(10.7)
.291(7.39) .393(9.98)
PIN 1 ID
.050(1.27) BSC
.513(13.0)
.497(12.6)
.105(2.67)
.092(2.34)
.012(.305)
.003(.076)
.013(.330)
.009(.229)
.035(0.889)
.015(.381)
0 REF
8
20X, 20-Lead, 0.173” Wide, Thin Super Small Outline
Package (TSSOP)
Dimensions in (Millimeters) and Inches
0.30(0.012)
0.18(0.007)
4.48(.176) 6.50(.256)
4.30(.169) 6.25(.246)
PIN 1 ID
0.65(.0256) BSC
6.60(.260)
6.40(.252)
1.10(0.043) MAX
0.15(.006)
0.05(.002)
0.18(.007)
0.09(.003)
0 REF
8
10
0.70(.028)
0.50(.020)
AT27C520
Similar pages