TI1 DAC7621 12-bit, parallel input digital-to-analog converter Datasheet

®
DAC
DAC7621
®
762
1
For most current data sheet and other product
information, visit www.burr-brown.com
12-Bit, Parallel Input
DIGITAL-TO-ANALOG CONVERTER
FEATURES
DESCRIPTION
● LOW POWER: 2.5mW
● FAST SETTLING: 7µs to 1 LSB
The DAC7621 is a 12-bit digital-to-analog converter
(DAC) with guaranteed 12-bit monotonicity performance over the industrial temperature range. It requires a single +5V supply and contains an input
register, latch, 2.435V reference, DAC, and high speed
rail-to-rail output amplifier. For a full-scale step, the
output will settle to 1 LSB within 7µs. The device
consumes 2.5mW (0.5mA at 5V).
● 1mV LSB WITH 4.095V FULL-SCALE
RANGE
● COMPLETE WITH REFERENCE
● 12-BIT LINEARITY AND MONOTONICITY
OVER INDUSTRIAL TEMP RANGE
● ASYNCHRONOUS RESET TO 0V
The parallel interface is compatible with a wide variety
of microcontrollers. The DAC7621 accepts a 12-bit
parallel word, has a double-buffered input logic structure and provides data readback. In addition, two
control pins provide a chip select (CS) function and
asynchronous clear (CLR) input. The CLR input can
be used to ensure that the DAC7621 output is 0V on
power-up or as required by the application.
APPLICATIONS
● PROCESS CONTROL
● DATA ACQUISITION SYSTEMS
● CLOSED-LOOP SERVO-CONTROL
● PC PERIPHERALS
● PORTABLE INSTRUMENTATION
The DAC7621 is available in a 20-lead SSOP package
and is fully specified over the industrial temperature
range of –40°C to +85°C.
VDD
Ref
12-Bit DAC
VOUT
12
CLR
DAC Register
LOADDAC
12
Input Register
12
CS
I/O Buffer
R/W
DAC7621
D0
D1 D2
D3 D4
D5 D6
D7 D8
D9 D10 D11
DGND
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
© 1998 Burr-Brown Corporation
SBAS107
PDS-1502B
Printed in U.S.A. March, 1999
SPECIFICATIONS
ELECTRICAL
At TA = –40°C to +85°C, and VDD = +5V, unless otherwise noted.
DAC7621E
PARAMETER
CONDITIONS
RESOLUTION
MIN
DAC7621EB
TYP
MAX
Guaranteed Monotonic
Code 000H
Code FFFH
ANALOG OUTPUT
Output Current
Load Regulation
Capacitive Load
Short-Circuit Current
Short-Circuit Duration
Code 800H
RLOAD ≥ 402Ω, Code 800H
No Oscillation
–2
–1
–1
4.079
±1/2
±1/2
+1
4.095
±5
±7
1
500
±20
Indefinite
GND or VDD
DIGITAL INPUT
Data Format
Data Coding
Logic Family
Logic Levels
VIH
VIL
IIH
IIL
TYP
+2
+1
+3
4.111
±1/4
±1/4
✻
4.095
✻
✻
✻
✻
✻
✻
3
✻
✻
✻
+4.75
TEMPERATURE RANGE
Specified Performance
–40
+5.0
0.5
2.5
0.001
LSB
LSB
LSB
V
mA
LSB
pF
mA
+5.25
1
5
0.004
✻
+85
✻
✻
✻
✻
✻
V
V
µA
µA
µs
nV-s
nV-s
✻
✻
✻
7
5
2
VIH = 5V, VIL = 0V, No Load, at Code 000H
VIH = 5V, VIL = 0V, No Load
∆VDD = ±5%
✻
✻
0.3 • VDD
±10
±10
POWER SUPPLY
VDD
IDD
Power Dissipation
Power Supply Sensitivity
+1
+1
✻
4.103
✻
✻
✻
0.7 • VDD
To ±1 LSB of Final Value
UNITS
Bits
–1
–1
✻
4.087
Parallel
Straight Binary
CMOS
DYNAMIC PERFORMANCE
Settling Time(2) (tS)
DAC Glitch
Digital Feedthrough
MAX
✻
12
ACCURACY
Relative Accuracy(1)
Differential Nonlinearity
Zero-Scale Error
Full Scale Voltage
MIN
✻
✻
✻
✻
V
mA
mW
%/%
✻
°C
✻ Same specification as for DAC7621E.
NOTES: (1) This term is sometimes referred to as Linearity Error or Integral Nonlinearity (INL). (2) Specification does not apply to negative-going transitions where
the final output voltage will be within 3 LSBs of ground. In this region, settling time may be double the value indicated.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
®
DAC7621
2
PIN CONFIGURATION
PIN DESCRIPTIONS
Top View
PIN
SSOP
LABEL
1
CLR
1
20
LOADDAC
VDD
2
19
CS
VOUT
3
18
R/W
AGND
4
17
DB0 (LSB)
DGND
5
DB11 (MSB)
DB10
16
DB1
6
15
DB2
7
14
DB3
DAC7621E
DB9
8
13
DB4
DB8
9
12
DB5
DB7
10
11
DB6
DESCRIPTION
CLR
Reset. Resets the DAC register to zero. Active
LOW. Asynchronous input.
2
VDD
Postive Power Supply
3
VOUT
DAC Output Voltage
4
AGND
Analog Ground
5
DGND
Digital Ground
6
DB11
Data Bit 11, MSB
7
DB10
Data Bit 10
8
DB9
Data Bit 9
9
DB8
Data Bit 8
10
DB7
Data Bit 7
11
DB6
Data Bit 6
12
DB5
Data Bit 5
13
DB4
Data Bit 4
14
DB3
Data Bit 3
15
DB2
Data Bit 2
16
DB1
Data Bit 1
17
DB0
Data Bit 0, LSB
18
R/W
Read and Write Control
19
CS
20
LOADDAC
ABSOLUTE MAXIMUM RATINGS(1)
Chip Select. Active LOW.
Loads the internal DAC register. The DAC register
is a transparent latch and is transparent when
LOADDAC is LOW (regardless of the state of CS or
CLK).
ELECTROSTATIC
DISCHARGE SENSITIVITY
VDD to GND .......................................................................... –0.3V to 6V
Digital Inputs to GND .............................................. –0.3V to VDD + 0.3V
VOUT to GND ........................................................... –0.3V to VDD + 0.3V
Power Dissipation ........................................................................ 325mW
Thermal Resistance, θJA ........................................................... 150°C/W
Maximum Junction Temperature .................................................. +150°C
Operating Temperature Range ...................................... –40°C to +85°C
Storage Temperature Range ....................................... –65°C to +150°C
Lead Temperature (soldering, 10s) .............................................. +300°C
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings”
may cause permanent damage to the device. Exposure to absolute maximum
conditions for extended periods may affect device reliability.
PACKAGE/ORDERING INFORMATION
PRODUCT
MINIMUM
RELATIVE
ACCURACY
(LSB)
DIFFERENTIAL
NONLINEARITY
(LSB)
SPECIFICATION
TEMPERATURE
RANGE
PACKAGE
PACKAGE
DRAWING
NUMBER(1)
DAC7621E
±2
±1
–40°C to +85°C
20-Lead SSOP
334
"
"
"
"
"
"
DAC7621EB
±1
±1
–40°C to +85°C
20-Lead SSOP
334
"
"
"
"
"
"
ORDERING
NUMBER(2)
TRANSPORT
MEDIA
DAC7621E
DAC7621E/1K
DAC7621EB
DAC7621EB/1K
Rails
Tape and Reel
Rails
Tape and Reel
NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/) are
available only in Tape and Reel in the quantities indicated (e.g., /1K indicates 1000 devices per reel). Ordering 1000 pieces of “DAC7621E/1K” will get a single
1000-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book.
®
3
DAC7621
TIMING DIAGRAMS
tWCS
CS
tWS
tWH
R/W
tRCS
CS
tLWD
tRDH
tRDS
LOADDAC
R/W
tDH
tDS
tDZ
Data Out
Data In
Data Valid
tCSD
Data Output Timing
Digital Input Timing
TIMING SPECIFICATIONS
LOGIC TRUTH TABLE
TA = –40°C to +85°C
SYMBOL
DESCRIPTION
tRCS
CS LOW for Read
MIN TYP MAX UNITS
200
ns
tRDS
R/W HIGH to CS LOW
10
ns
tRDH
R/W HIGH after CS HIGH
0
ns
tDZ
CS HIGH to Data Bus
in High Impedance
100
tCSD
CS LOW to Data Bus Valid
tWCS
CS LOW for Write
50
100
ns
160
tWS
R/W LOW to CS LOW
0
ns
tWH
R/W LOW after CS HIGH
5
ns
tDS
Data Valid to CS LOW
0
ns
tDH
Data Valid after CS HIGH
5
ns
tLWD
LOADDAC LOW
50
ns
®
DAC7621
4
DAC
REGISTER
L
Write
Write
Write
H
Write
Hold
Write Input
Read
Hold
Read Input
Hold
Update
Update
Hold
Hold
Hold
CS
L
L
L
L
H
L
H
X
H
L
X
H
H
X = Don’t Care.
ns
INPUT
REGISTER
R/W
LOADDAC
MODE
TYPICAL PERFORMANCE CURVES
At TA = +25°, and VDD = 5V, unless otherwise specified.
PULL-DOWN VOLTAGE vs OUTPUT SINK CURRENT
OUTPUT SWING vs LOAD
1k
4.5
4.0
100
Delta VOUT (mV)
Output Voltage (V)
3.5
3.0
2.5
2.0
1.5
1.0
85°C (mV)
25°C
10
1
–40°C
0.1
Data = 000H
0.5
0.01
0.001
0
10
100
1k
10k
100k
0.01
0.1
1
10
100
Current (mA)
Load Resistance (Ω)
SUPPLY CURRENT vs LOGIC INPUT VOLTAGE
BROADBAND NOISE
4.0
Supply Current (mA)
Noise Voltage (1mV/div)
3.5
Code = FFFH
BW = 2MHz
3.0
2.5
2.0
1.5
1.0
0.5
0
5
Time (2µs/div)
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
Logic Voltage (V)
POWER SUPPLY REJECTION vs FREQUENCY
MINIMUM SUPPLY VOLTAGE vs LOAD
70
5.0
Data = FFFH
VDD = 5V
±200mV AC
60
4.8
VDD Minimum (V)
50
PSR (dB)
∆VFS = 1 LSB
Data = FFFH
40
30
20
4.6
4.4
4.2
10
0
10
100
1k
10k
100k
4.0
0.010
1M
Frequency (Hz)
0.100
1.000
10.000
Output Load Current (mA)
®
5
DAC7621
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°, and VDD = 5V, unless otherwise specified.
SUPPLY CURRENT vs TEMPERATURE
SHORT-CIRCUIT CURRENT vs OUTPUT VOLTAGE
4.0
80
Positive
Current
Limit
Supply Current (mA)
40
VLOGIC = 3.5V
Data = FFFH
No Load
3.5
Data = 800H
Output tied to ISOURCE
20
0
–20
–40
Negative
Current
Limit
–60
3.0
2.5
2.0
VDD = 5.0V
VDD = 5.25V
1.5
1.0
0.5
VDD = 4.75V
0
–80
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
–40 –30 –20 –10
5.0
0
10
20
30
40
50
60 70
Output Voltage (V)
Temperature (°C)
MID-SCALE GLITCH PERFORMANCE
MID-SCALE GLITCH PERFORMANCE
LOADDAC
80 90
VOUT (2mV/div)
VOUT (2mV/div)
LOADDAC
VOUT
VOUT
7FFH to 800H
800H to 7FFH
Time (500ns/div)
Time (500ns/div)
LARGE-SIGNAL SETTLING TIME
RISE TIME DETAIL
CL = 110pF
RL = No Load
Output Voltage (1mV/div)
LD
1V/div
Output Current (mA)
60
VOUT
VOUT
LD
Time (10µs/div)
Time (20µs/div)
®
DAC7621
6
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°, and VDD = 5V, unless otherwise specified.
OUTPUT VOLTAGE NOISE vs FREQUENCY
FALL TIME DETAIL
10.000
Noise (µV/√Hz)
Output Voltage (1mV/div)
Data = FFFH
VOUT
LD
1.000
0.100
0.010
10
Time (10µs/div)
100
1k
10k
100k
Frequency (Hz)
LONG-TERM DRIFT ACCELERATED BY BURN-IN
TOTAL UNADJUSTED ERROR HISTOGRAM
60
144 Units
6
T.U.E = ΣINL = ZS + FS
Sample Size = 300 Units
TA = +25°C
50
4
Number of Units
Output Voltage Change (mV)
8
2
0
min
–2
avg
–4
40
30
20
max
10
–6
–8
0
200
400
600
800
1000
0
–12
1200
–8
–4
0
4
8
12
Hours of Operation at +150°C
FULL-SCALE VOLTAGE vs TEMPERATURE
ZERO-SCALE VOLTAGE vs TEMPERATURE
4.115
3
4.105
2
Zero-Scale (mV)
Full-Scale Output (V)
No Load
Sample Size = 300
Avg + 3σ
4.110
4.100
4.095
Avg
4.090
4.085
1
0
4.080
Avg – 3σ
4.075
–1
–50
–25
0
25
50
75
100
125
–50
Temperature (°C)
–25
0
25
50
75
100
125
Temperature (°C)
®
7
DAC7621
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°, and VDD = 5V, unless otherwise specified.
DIFFERENTIAL LINEARITY ERROR vs DIGITAL CODE
(at +25°C)
LINEARITY ERROR vs DIGITAL CODE
(at +25°C)
2.0
Differential Linearity Error (LSBs)
2.0
Linearity Error (LSBs)
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
0
512
1024
1536
2048
2560
3072
3584
0.5
0
–0.5
–1.0
–1.5
0
4096
512
1024
1536
2048
2560
3072
3584
4096
Code
Code
LINEARITY ERROR vs DIGITAL CODE
(at +85°C)
DIFFERENTIAL LINEARITY ERROR vs DIGITAL CODE
(at +85°C)
1
Differential Linearity Error (LSBs)
1
Linearity Error (LSBs)
1.0
–2.0
–2.0
0.5
0
–0.5
0.5
0
–0.5
–1.0
–1.0
0
512
1024
1536
2048
2560
3072
3584
0
4096
512
1024
1536
2048
2560
3072
3584
4096
Code
Code
LINEARITY ERROR vs DIGITAL CODE
(at –40°C)
DIFFERENTIAL LINEARITY ERROR vs DIGITAL CODE
(at –40°C)
1
Differential Linearity Error (LSBs)
1
Linearity Error (LSBs)
1.5
0.5
0
–0.5
–1.0
0.5
0
–0.5
–1.0
0
512
1024
1536
2048
2560
3072
3584
4096
0
Code
1024
1536
2048
Code
®
DAC7621
512
8
2560
3072
3584
4096
OPERATION
The digital data into the DAC7621 is double-buffered. This
means that new data can be entered into the DAC without
disturbing the old data and the analog output of the converter. At some point after the data has been entered into the
serial shift register, this data can be transferred into the DAC
register. This transfer is accomplished with a HIGH to LOW
transition of the LOADDAC pin. However, the LOADDAC
pin makes the DAC register transparent. If new data becomes available on the bus register while LOADDAC is
LOW, the DAC output voltage will change as the data
changes. To prevent this, CS must be returned HIGH prior
to changing data on the bus.
The DAC7621 is a 12-bit digital-to-analog converter (DAC)
complete with an input shift register, DAC register, lasertrimmed 12-bit DAC, on-board reference, and a rail-to-rail
output amplifier. Figure 1 shows the basic operation of the
DAC7621.
INTERFACE
Figure 1 shows the basic connection between a
microcontroller and the DAC7621. The interface consists of
a Read/Write (R/W), data, and a load DAC signal
(LOADDAC). In addition, a chip select (CS) input is available to enable the DAC7621 when there are multiple devices. The data format is Straight Binary. An asynchronous
clear input (CLR) is provided to simplify start-up or periodic
resets. Table I shows the relationship between input code
and output voltage.
At any time, the contents of the DAC register can be set to
000H (analog output equals 0V) by taking the CLR input
LOW. The DAC register will remain at this value until CLR
is returned HIGH and LOADDAC is taken LOW to allow
the contents of the input register to be transferred to the
DAC register. If LOADDAC is LOW when CLR is taken
LOW, the DAC register will be set to 000H and the analog
output driven to 0V. When CLR is returned HIGH, the DAC
register and the analog output will respond accordingly.
DAC7621 Full-Scale Range = 4.095V
Least Significant Bit = 1mV
DIGITAL INPUT CODE
STRAIGHT OFFSET BINARY
ANALOG OUTPUT
(V)
FFFH
801H
800H
7FFH
000H
+4.095
+2.049
+2.048
+2.047
0
DESCRIPTION
DIGITAL-TO-ANALOG CONVERTER
Full Scale
Midscale + 1 LSB
Midscale
Midscale – 1 LSB
Zero Scale
The internal DAC section is a 12-bit voltage output
device that swings between ground and the internal reference voltage. The DAC is realized by a laser-trimmed
R-2R ladder network which is switched by N-channel
MOSFETs. The DAC output is internally connected to
the rail-to-rail output operational amplifier.
TABLE I. Digital Input Code and Corresponding Ideal
Analog Output.
DAC7621E
Clear
+5V
10µF
+
0.1µF
0V to
+4.095V
Data Bus
1
CLR
2
3
4
5
6
7
LOADDAC
20
Load DAC
VDD
CS
19
Chip Select
VOUT
R/W
18
Read/Write
AGND
DB0
17
DGND
DB1
16
DB11
DB2
15
DB10
DB3
14
8
DB9
DB4
13
9
DB8
DB5
12
10 DB7
DB6
11
Data Bus
FIGURE 1. Basic Operation of the DAC7621.
®
9
DAC7621
R-2R DAC
2R
Output Amplifier
R
Buffer
2R
R2
2.435V
Bandgap
Reference
R
2R
R1
R
2R
2R
FIGURE 2. Simplified Schematic of Analog Portion.
OUTPUT AMPLIFIER
A precision, low-power amplifier buffers the output of the
DAC section and provides additional gain to achieve a 0V
to 4.095V range. The amplifier has low offset voltage, low
noise, and a set gain of 1.682V/V (4.095/2.435). See Figure
2 for an equivalent circuit schematic of the analog portion
of the DAC7621.
POWER SUPPLY
A BiCMOS process and careful design of the bipolar and
CMOS sections of the DAC7621 result in a very low power
device. Bipolar transistors are used where tight matching
and low noise are needed to achieve analog accuracy, and
CMOS transistors are used for logic, switching functions
and for other low power stages.
If power consumption is critical, it is important to keep the
logic levels on the digital inputs (R/W, CLK, CS, LOADDAC,
CLR) as close as possible to either VDD or ground. This will
keep the CMOS inputs (see “Supply Current vs Logic Input
Voltages” in the Typical Performance Curves) from shunting current between VDD and ground.
The DAC7621 power supply should be bypassed as shown
in Figure 1. The bypass capacitors should be placed as close
to the device as possible, with the 0.1µF capacitor taking
priority in this regard. The “Power Supply Rejection vs
Frequency” graph in the Typical Performance Curves section shows the PSRR performance of the DAC7621. This
should be taken into account when using switching power
supplies or DC/DC converters.
The output amplifier has a 7µs typical settling time to ±1
LSB of the final value. Note that there are differences in the
settling time for negative-going signals versus positivegoing signals.
The rail-to-rail output stage of the amplifier provides the
full-scale range of 0V to 4.095V while operating on a
supply voltage as low as 4.75V. In addition to its ability to
drive resistive loads, the amplifier will remain stable while
driving capacitive loads of up to 500pF. See Figure 3 for an
equivalent circuit schematic of the amplifier’s output driver
and the Typical Performance Curves section for more information regarding settling time, load driving capability, and
output noise.
In addition to offering guaranteed performance with VDD in
the 4.75V to 5.25V range, the DAC7621 will operate with
reduced performance down to 4.5V. Operation between
4.5V and 4.75V will result in longer settling time, reduced
performance, and current sourcing capability. Consult the
“VDD vs Load Current” graph in the Typical Performance
Curves section for more information.
VDD
P-Channel
VOUT
N-Channel
AGND
FIGURE 3. Simplified Driver Section of Output Amplifier.
®
DAC7621
10
APPLICATIONS
signals and should cross them at right angles. A solid analog
ground plane around the D/A package, as well as under it in
the vicinity of the analog and power supply pins, will isolate
the D/A from switching currents. It is recommended that
DGND and AGND be connected directly to the ground
planes under the package.
POWER AND GROUNDING
The DAC7621 can be used in a wide variety of situations—
from low power, battery operated systems to large-scale
industrial process control systems. In addition, some applications require better performance than others, or are particularly sensitive to one or two specific parameters. This
diversity makes it difficult to define definite rules to follow
concerning the power supply, bypassing, and grounding.
The following discussion must be considered in relation to
the desired performance and needs of the particular system.
If several DAC7621s are used, or if sharing supplies with
other components, connecting the AGND and DGND lines
together at the power supplies once, rather than at each chip,
may produce better results.
The power applied to VDD should be well regulated and lownoise. Switching power supplies and DC/DC converters will
often have high-frequency glitches or spikes riding on the
output voltage. In addition, digital components can create
similar high frequency spikes as their internal logic switches
states. This noise can easily couple into the DAC output
voltage through various paths between VDD and VOUT.
A precision analog component requires careful layout, adequate bypassing, and a clean, well-regulated power supply.
As the DAC7621 is a single-supply, +5V component, it will
often be used in conjunction with digital logic,
microcontrollers, microprocessors, and digital signal processors. The more digital logic present in the design and the
higher the switching speed, the more difficult it will be to
achieve good performance.
The DAC7621 has separate analog ground and digital ground
pins. The current through DGND is mostly switching transients and are up to 4mA peak in amplitude. The current
through AGND is typically 0.5mA.
As with the GND connection, VDD should be connected to
a +5V power supply plane or trace that is separate from the
connection for digital logic until they are connected at the
power entry point. In addition, the 10µF and 0.1µF capacitors shown in Figure 4 are strongly recommended and
should be installed as close to VDD and ground as possible.
In some situations, additional bypassing may be required
such as a 100µF electrolytic capacitor or even a “Pi” filter
made up of inductors and capacitors—all designed to essentially lowpass filter the +5V supply, removing the high
frequency noise (see Figure 4).
For best performance, separate analog and digital ground
planes with a single interconnection point to minimize
ground loops. The analog pins are located adjacent to each
other to help isolate analog from digital signals. Analog
signals should be routed as far as possible from digital
Digital Circuits
+5V
Power
Supply
+5V
+5V
GND
DAC7621
GND
100µF
+
+
VDD
10µF
0.1µF
AGND
Optional
DGND
Other
Analog
Components
FIGURE 4. Suggested Power and Ground Connections for a DAC7621 Sharing a +5V Supply with a Digital System with a
Single Ground Plane.
®
11
DAC7621
PACKAGE OPTION ADDENDUM
www.ti.com
25-Dec-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
DAC7621E
ACTIVE
SSOP
DB
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7621E
DAC7621E/1K
ACTIVE
SSOP
DB
20
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7621E
DAC7621E/1KG4
ACTIVE
SSOP
DB
20
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7621E
DAC7621EB
ACTIVE
SSOP
DB
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7621E
B
DAC7621EB/1K
ACTIVE
SSOP
DB
20
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7621E
B
DAC7621EBG4
ACTIVE
SSOP
DB
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7621E
B
DAC7621EG4
ACTIVE
SSOP
DB
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
DAC7621E
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Dec-2015
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Dec-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DAC7621E/1K
SSOP
DB
20
1000
330.0
16.4
8.2
7.5
2.5
12.0
16.0
Q1
DAC7621EB/1K
SSOP
DB
20
1000
330.0
16.4
8.2
7.5
2.5
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Dec-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC7621E/1K
SSOP
DB
20
1000
346.0
346.0
33.0
DAC7621EB/1K
SSOP
DB
20
1000
346.0
346.0
33.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages