TSC EGP10J 1.0 amp. glass passivated high efficient plastic rectifier Datasheet

EGP10A THRU EGP10M
1.0 AMP. Glass Passivated High Efficient Plastic Rectifiers
Voltage Range
50 to 1000 Volts
Current
1.0 Ampere
DO-41
Features
Plastic material used carries Underwriters Laboratory
Classification 94V-0
Glass passivated cavity-free junction
Superfast recovery time for high efficiency
Low forward voltage, high current capability
Low leakage current
High surge current capability
High temperature soldering guaranteed:
300℃/10seconds, .375”(9.5mm) lead length at 5 lbs.,
(2.3kg) tension
Mechanical Data
Cases: JEDEC DO-41 molded plastic over glass
body
Lead: Plated axial leads, solderable per MIL-STD750, Method 2026
Polarity: Color band denotes cathode end
Mounting position: Any
Weight: 0.012 ounce, 0.3 gram
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25℃ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Symbol EGP EGP EGP
Type Number
10A 10B 10D
Maximum Recurrent Peak Reverse Voltage VRRM
50 100 200
Maximum RMS Voltage
VRMS 35 70 140
Maximum DC Blocking Voltage
50 100 200
VDC
EGP EGP EGP EGP EGP Units
10F 10G 10J 10K 10M
300 400 600 800 1000
210 280 420 560 700
300 400 600 800 1000
V
V
V
Maximum Average Forward Rectified
Current .375” (9.5mm) Lead Length
@TA = 55℃
I(AV)
1.0
A
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
IFSM
30.0
A
Maximum Instantaneous Forward Voltage
@ 1.0A
VF
Maximum DC Reverse Current @ TA=25℃
at Rated DC Blocking Voltage @ TA=125℃
IR
Maximum Reverse Recovery Time ( Note 1 )
TJ=25℃
Trr
Typical Junction Capacitance ( Note 2 )
Typical Thermal Resistance (Note 3)
Operating Temperature Range
Cj
RθJA
0.95
1.25
1.7
5.0
100.0
uA
uA
50
75
20
15
70
-65 to + 150
-65 to + 150
TJ
TSTG
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1.0 MHz and Applied Reverse Voltage of 4.0 Volts D.C.
3. Mount on Cu-Pad Size 5mm x 5mm on P.C.B.
Storage Temperature Range
- 584 -
V
nS
pF
℃/W
℃
℃
RATINGS AND CHARACTERISTIC CURVES (EGP10A THRU EGP10M)
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
10W
NONINDUCTIVE
trr
+0.5A
(-)
DUT
PULSE
GENERATOR
(NOTE 2)
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
(+)
-1.0A
1cm
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
RESISTIVE OR
INDUCTIVE LOAD
0.375" (9.5mm) LEAD LENGTH
0.5
0
0
25
50
75
100
125
150
175
o
PEAK FORWARD SURGE CURRENT. (A)
AMBIENT TEMPERATURE. ( C)
FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
30
20
Tj=150 0C
100
Tj=100 0C
10
1
Tj=25 0C
0.1
0.01
0
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
15
10
50
FIG.6- TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
PULSE WIDTH-300 S
1% DUTY CYCLE
5
0
1
100
10
NUMBER OF CYCLES AT 60Hz
FIG.4- TYPICAL JUNCTION CAPACITANCE
60
JUNCTION CAPACITANCE.(pF)
1000
Tj=Tj max.
8.3ms Single Half Sine Wave
JEDEC Method
25
SET TIME BASE FOR
5/ 10ns/ cm
FIG.5- TYPICAL REVERSE CHARACTERISTICS
Tj=25 0C
f=1.0MHz
Vsig=50mVp-p
50
40
30
20
10
INSTANTANEOUS FORWARD CURRENT. (A)
AVERAGE FORWARD CURRENT. (A)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
1.0
0
-0.25A
INSTANTANEOUS REVERSE CURRENT. ( A)
(+)
50Vdc
(approx)
(-)
10
Tj=25 0C
1
Tj=150 0C
0.1
EGP10A-EGP10D
EGP10F EGP10M
5
EGP10A-EGP10D
EGP10F & EGP10M
0
0.1
1
10
REVERSE VOLTAGE. (V)
0.01
100
1000
0.2
0.4
0.6
0.8
1.0
1.2
1.4
FORWARD VOLTAGE. (V)
- 585 -
1.6
1.8
Similar pages