Panasonic MN101C47 Remote control input discriminant circuit built-in Datasheet

MN101C47C, MN101C47D
Type
MN101C47C
MN101C47D
ROM (×× 8-bit)
48 K
64 K
RAM (×× 8-bit)
1.5 K
2K
Package
(Conventional Package)
SDIP042-P-0600C *Lead-free, LQFP064-P-1414 *Lead-free
(SDIP042-P-0600)
Minimum Instruction
Execution Time
279 ns (at 3.0 V to 3.6 V, 14.32 MHz)
Interrupts
External (6 lines)
Internal (8 lines) : Timer × 3, A/D, OSD, I2C, Remote control, Watchdog
Timer Counter
8-bit timer × 3
Watchdog timer: system clock fs 1/216, 1/218, 1/220 triple selection
Serial Interface
I2C × 1: for multimaster mode, bus line (output) has 2 systems
Caption
• Built-in sync separator × 2
I/O Pins
I/O
35
• Common use: 29
A/D Inputs
5-bit × 8-ch. (with S/H)
PWM
8-bit × 6-ch. , 14-bit × 1-ch.
Special Ports
Remote control reception
CRTC
1-layer display (graphics, characters)
Notes
Remote control input discriminant circuit built-in
Support Tool
1
In-circuit Emulator
PX-ICE101C/D+PX-PRB101C47-SDIP046-P-0600-M (under development)
EPROM Built-in Type
Type
MN101CF46F (under development)
ROM (× 8-bit)
96 K
RAM (× 8-bit)
3K
Minimum instruction execution time
279 ns (at 3.0 V to 3.6 V, 14.32 MHz)
Package
SDIP042-P-0600C *Lead-free, LQFP064-P-1414 *Lead-free
(Conventional Package)
(SDIP042-P-0600)
MAD00027CEM
MN101C47C, MN101C47D
Pin Assignment
(
IRQ0,RMIN,P00
1
42
VSS
*1 SDA1,P01
2
41
OSC2
*1 SCL1,P02
3
40
OSC1
IRQ1,ADIN0,P03
4
39
VDD(VPP) *2
ADIN1,P04
5
38
P42,SCL0 *1
ADIN2,P05
6
37
P41,SDA0 *1
ADIN3,P06
7
36
P40,PWM
ADIN4,P07
8
35
P37,NVSYNC,IRQ5
ADIN5,P10
9
34
P36,NRST
ADIN6,P11
10
33
P35,YM
ADIN7,P12
11
32
P34,ROUT
*3 MMOD
12
31
P33,GOUT
SYSCLK,P13
13
30
P32,BOUT
*1 PWM0,P14
14
29
P31,YS
PWM1,P15
15
28
VSS
PWM2,P16
16
27
P30,NHSYNC
IRQ2,PWM3,P17
17
26
P27
IRQ3,PWM4,P20
18
25
P26
*1 IRQ4,PWM5,P21
19
24
P25
VDD
20
23
P24
P22
21
22
P23
MN101C47C
MN101C47D
SDIP042-P-0600C
) : Conventional Package
*Lead-free
(SDIP042-P-0600)
*1: 5 V dielectric Nch open drain output pin
*2: Mask ROM = VDD, Flash memory built-in type = VPP
33
34
35
36
37
38
39
40
41
42
43
44
45
46
49
32
50
31
51
30
52
29
53
28
54
27
55
26
MN101C47C
MN101C47D
56
57
25
24
16
15
14
13
12
11
10
P41,SDA0 *1
N.C.
P42, SCL0 *1
N.C.
VDD(VPP)
OSC1
OSC2
VSS
IRQ0,RMIN,P00
SDA1,P01 *1
SCL1,P02 *1
IRQ1,ADIN0,P03
ADIN1,P04
N.C.
N.C.
ADIN2,P05
N.C.
N.C.
PWM1,P15
N.C.
*1 PWM0,P14
SYSCLK,P13
N.C.
*2 MMOD
ADIN7,P12
ADIN6,P11
ADIN5,P10
N.C.
ADIN4,P07
ADIN3,P06
N.C.
N.C.
9
17
8
18
64
7
19
63
6
20
62
5
21
61
4
22
60
3
23
59
2
58
1
P30,NHSYNC
N.C.
N.C.
P27
P26
P25
P24
P23
P22
N.C.
VDD
*1 P21,PWM5,IRQ4
P20,PWM4,IRQ3
P17,PWM3,IRQ2
N.C.
P16,PWM2
47
48
N.C.
N.C.
VSS
N.C.
P31,YS
P32,BOUT
P33,GOUT
P34,ROUT
P35,YM
P36,NRST
N.C.
P37,NVSYNC,IRQ5
N.C.
P40,PWM
N.C.
N.C.
*3: MMOD = H (fixed) (Set the test mode pin to the normal mode.)
LQFP064-P-1414
*Lead-free
*1: 5 V dielectric Nch open drain output pin
*2: MMOD = H (fixed)
MAD00027CEM
2
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government
if any of the products or technologies described in this material and controlled under the "Foreign
Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license.
(3) We are not liable for the infringement of rights owned by a third party arising out of the use of the
product or technologies as described in this material.
(4) The products described in this material are intended to be used for standard applications or general
electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(5) The products and product specifications described in this material are subject to change without
notice for modification and/or improvement. At the final stage of your design, purchasing, or use of
the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that
the latest specifications satisfy your requirements.
(6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of
incidence of break down and failure mode, possible to occur to semiconductor products. Measures
on the systems such as redundant design, arresting the spread of fire or preventing glitch are
recommended in order to prevent physical injury, fire, social damages, for example, by using the
products.
(7) When using products for which damp-proof packing is required, observe the conditions (including
shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets
are individually exchanged.
(8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written
permission of Matsushita Electric Industrial Co., Ltd.
2002 JUL
Similar pages