EPCOS B65541-W-R41 Pm/p/p cores halves/ep/tt/pr core Datasheet

PM/P/P Cores Halves/EP/TT/PR Cores
Series/Type:
P 14 x 8
The following products presented in this data sheet are being withdrawn.
Ordering Code
Substitute Product
B65541D0000R026
B65542A50020000
B65542A50000000
B65549E0003X101
B65541D0000R048
B65549E0004X23
Date of
Withdrawal
2002-08-02
2003-08-08
2004-10-18
2003-08-08
Deadline Last
Orders
2002-12-31
2005-03-31
2005-03-31
2004-02-29
Last Shipments
2003-03-31
2005-09-30
2005-09-30
2004-08-31
For further information please contact your nearest EPCOS sales office, which will also support
you in selecting a suitable substitute. The addresses of our worldwide sales network are
presented at www.epcos.com/sales.
P 14 × 8
Core
B65541
9,2 _ 0,5
with
without
center hole center hole
0,25+0,1
mm–1
mm
mm2
mm2
mm3
Approx. weight (per set)
m
3,2
ø6 _ 0,2
ø3+0,1
s
0,73
21
28,7
23,6
603
8,5 _ 0,3
0,8
20
25
20
500
5,6+0,4
Σl/A
le
Ae
A min
Ve
M2
3,5
1,3±0,15
14,3 _ 0,5
11,6+0,4
Magnetic characteristics (per set)
3,6+0,5
■ In accordance with IEC 60133
■ Pot cores are supplied in sets
FPK0085-A
g
Gapped
Material
A L value
nH
µe
s
approx.
mm
Ordering code 1)
-D with center hole
-T with threaded sleeve
M33
100 ± 3 %
0,30
64
B65541-+100-A33
N48
160 ± 3 %
250 ± 3 %
315 ± 3 %
400 ± 3 %
0,16
0,10
0,08
0,05
102
159
201
255
B65541-+160-A48
B65541-+250-A48
B65541-+315-A48
B65541-+400-A48
Ungapped
Material
A L value
µe
K1
M33
N26
N30
T38
N87
nH
140 + 30/– 20 %
970 + 30/– 20 %
2300 + 30/– 20 %
4600 + 30/– 20 %
9800 + 40/– 30 %
2800 + 30/– 20 %
nH
89
617
1460
2670
5690
1630 1550
N41
3300 + 30/– 20 % 1940 1940
A L1min P V
W/set
Ordering code
-D with center hole
-W w/o center hole
B65541-D-R1
B65541-D-R33
B65541-D-R26
B65541-W-R30
B65541-W-Y38
B65541-W-R87
< 0,26
(200 mT, 100 kHz, 100 °C)
< 0,09
B65541-W-R41
(200 mT, 25 kHz, 100 °C)
1) Replace the + by the code letter ”D“ or ”T“ for the required version.
329 08/01
P 14 × 8
Accessories
B65542
Coil former
Standard:
Material:
Winding:
to IEC 60133
GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085:
F max. operating temperature 155 °C), color code black
see “Processing Notes”, page 155
Insulating washer 1 between core and coil former
■ For tolerance compensation and for insulation
■ Polycarbonate spring washer (UL 94 V-0, insulation class to IEC 60085: E
120 °C), 0,04 mm thick
Insulating washer 2 between core and terminal carrier
■ For increased dielectric strength
■ Made of polycarbonate (UL 94 V-0, insulation class to IEC 60085: E
120 °C), 0,08 mm thick
Coil former
Ordering code
Sections
AN
mm2
lN
mm
A R value
µΩ
1
8,4
28
115
B65542-B-T1
2
7,6
28
127
B65542-B-T2
Insulating washer 1 (reel packing, PU = 1 reel)
B65542-A5000
Insulating washer 2 (bulk)
B65542-A5002
Coil former
ø6,1+0,1
ø7,1_ 0,1
11,5 _ 0,2
2+0,6
AN
0,5
0,4
5,4 _ 0,1
FPK0087-R
Insulating washer 2
ø11,8±0,2
ø5,8±0,2
2,5
Insulating washer 1
6±0,2
1,2±0,2
14 _ 0,2
FPK0088-Z
330 08/01
FPK0089-8
P 14 × 8
Accessories
B65545
Mounting assembly for printed circuit boards
■ The set comprises a terminal carrier and a yoke
■ For snap-in connection
Terminal carrier
Material:
GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085:
F max. operating temperature 155 °C), color code black
Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 °C, 2 s
Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 °C, 3,5 s
Yoke
Spring yoke, made of tinned nickel silver (0,25 mm), with ground terminal
Complete mounting assembly
(4 solder terminals)
Ordering code: B65545-B9
Complete mounting assembly
(6 solder terminals)
Ordering code: B65545-B10
4 solder terminals
6 solder terminals
Ground
Ground
Hole arrangement
View in mounting
direction
Hole arrangement
View in mounting
direction
Ground
Ground
*)
a)
b)
c)
This recess must be on the side of the grounding pin to ensure that the yoke locks in position.
Yoke
Terminal carrier with 4 solder terminals
Terminal carrier with 6 solder terminals
331 08/01
P 14 × 8
B63399
Accessories
B65549
Adjusting screw
■ Tube core with thread and core brake made of GFR polyterephthalate
Plastic adjusting screwdriver (not shown)
Plastic handle for adjusting screwdriver (not shown)
Core P 14 × 8
Material
Adjusting screw
Tube core
AL value Fig. ∅ × length
nH
mm
Material Color
code
Min.
adjusting
range
Ordering code
%
M 33
40
a
2,6 × 2,0
Si 1
green
15
B65549-E3-X101
N 48
160
250
315
400
b
2,76 × 2,9
N 22
black
20
12
11
6
B65549-E4-X23
Adjusting screwdriver
B63399-B4
Handle
B63399-B5
Adjusting screw
a
b
332 08/01
Herausgegeben von EPCOS AG
Marketing Kommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND
 EPCOS AG 2000. Alle Rechte vorbehalten. Vervielfältigung, Veröffentlichung, Verbreitung und
Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG
nicht gestattet.
Mit den Angaben in dieser Broschüre werden die Bauelemente spezifiziert, keine Eigenschaften
zugesichert. Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen
für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird.
Diese Broschüre ersetzt die vorige Ausgabe.
Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgelegenen Vertrieb der EPCOS AG oder an unsere Vertriebsgesellschaften im Ausland.
Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte
darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsgesellschaft einzuholen.
Published by EPCOS AG
Marketing Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY
 EPCOS AG 2000. All Rights Reserved. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited.
The information contained in this brochure describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for
the Supply of Products and Services of the Electrical and Electronics Industry recommended by the
ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed.
This brochure replaces the previous edition.
For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or
the international Representatives.
Due to technical requirements components may contain dangerous substances. For information on
the type in question please also contact one of our Sales Offices.
1
Similar pages