ON MTP23P06V Power mosfet 23 amps, 60 volt Datasheet

MTP23P06V
Preferred Device
Power MOSFET
23 Amps, 60 Volts
P−Channel TO−220
This Power MOSFET is designed to withstand high energy in the
avalanche and commutation modes. Designed for low voltage, high
speed switching applications in power supplies, converters and power
motor controls, these devices are particularly well suited for bridge
circuits where diode speed and commutating safe operating areas are
critical and offer additional safety margin against unexpected voltage
transients.
http://onsemi.com
23 AMPERES, 60 VOLTS
RDS(on) = 120 mW
P−Channel
D
Features
• Avalanche Energy Specified
• IDSS and VDS(on) Specified at Elevated Temperature
• Pb−Free Package is Available*
G
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Rating
S
Symbol
Value
Unit
Drain−to−Source Voltage
VDSS
60
Vdc
Drain−to−Gate Voltage (RGS = 1.0 MW)
VDGR
60
Vdc
Gate−to−Source Voltage
− Continuous
− Non−repetitive (tp ≤ 10 ms)
VGS
VGSM
± 15
± 25
Vdc
Vpk
ID
ID
23
15
81
Adc
PD
90
0.60
W
W/°C
TJ, Tstg
−55 to 175
°C
Single Pulse Drain−to−Source Avalanche
Energy − Starting TJ = 25°C
(VDD = 25 Vdc, VGS = 10 Vdc, Peak
IL = 23 Apk, L = 3.0 mH, RG = 25 W)
EAS
794
mJ
Thermal Resistance − Junction−to−Case
Thermal Resistance − Junction−to−Ambient
RqJC
RqJA
1.67
62.5
°C/W
TL
260
°C
Drain Current − Continuous @ 25°C
Drain Current − Continuous @ 100°C
Drain Current − Single Pulse (tp ≤ 10 ms)
Total Power Dissipation @ 25°C
Derate above 25°C
Operating and Storage Temperature Range
Maximum Lead Temperature for Soldering
Purposes, 1/8″ from Case for 10 seconds
IDM
MARKING DIAGRAM
AND PIN ASSIGNMENT
Apk
TO−220AB
CASE 221A
STYLE 5
1
2
3
MTP23P06V
A
Y
WW
G
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
1
2
Drain
3
Source
= Device Code
= Location Code
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
Device
June, 2006 − Rev. 4
MTP
23P06VG
AYWW
1
Gate
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
© Semiconductor Components Industries, LLC, 2006
4
Drain
4
Package
Shipping
MTP23P06V
TO−220AB
50 Units/Rail
MTP23P06VG
TO−220AB
(Pb−Free)
50 Units/Rail
Preferred devices are recommended choices for future use
and best overall value.
Publication Order Number:
MTP23P06V/D
MTP23P06V
ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted)
Symbol
Characteristic
Min
Typ
Max
Unit
60
−
−
60.5
−
−
Vdc
mV/°C
−
−
−
−
10
100
−
−
100
nAdc
2.0
−
2.8
5.3
4.0
−
Vdc
mV/°C
−
0.093
0.12
W
−
−
−
−
3.3
3.2
5.0
11.5
−
Ciss
−
1160
1620
Coss
−
380
530
Crss
−
105
210
td(on)
−
13.8
30
tr
−
98.3
200
td(off)
−
41
80
tf
−
62
120
QT
−
38
50
Q1
−
7.0
−
Q2
−
18
−
Q3
−
14
−
−
−
2.2
1.8
3.5
−
trr
−
142.2
−
ta
−
100.5
−
tb
−
41.7
−
QRR
−
0.804
−
−
3.5
4.5
−
−
7.5
−
OFF CHARACTERISTICS
V(BR)DSS
Drain−Source Breakdown Voltage
(VGS = 0 Vdc, ID = 0.25 mAdc)
Temperature Coefficient (Positive)
Zero Gate Voltage Drain Current
(VDS = 60 Vdc, VGS = 0 Vdc)
(VDS = 60 Vdc, VGS = 0 Vdc, TJ = 150°C)
IDSS
Gate−Body Leakage Current (VGS = ± 15 Vdc, VDS = 0 Vdc)
IGSS
mAdc
ON CHARACTERISTICS (Note 1)
Gate Threshold Voltage
(VDS = VGS, ID = 250 mAdc)
Threshold Temperature Coefficient (Negative)
VGS(th)
Static Drain−Source On−Resistance (VGS = 10 Vdc, ID = 11.5 Adc)
RDS(on)
Drain−Source On−Voltage
(VGS = 10 Vdc, ID = 23 Adc)
(VGS = 10 Vdc, ID = 11.5 Adc, TJ = 150°C)
VDS(on)
Forward Transconductance
(VDS = 10.9 Vdc, ID = 11.5 Adc)
Vdc
gFS
Mhos
DYNAMIC CHARACTERISTICS
Input Capacitance
Output Capacitance
(VDS = 25 Vdc, VGS = 0 Vdc, f = 1.0 MHz)
Transfer Capacitance
pF
SWITCHING CHARACTERISTICS (Note 2)
Turn−On Delay Time
Rise Time
Turn−Off Delay Time
(VDD = 30 Vdc, ID = 23 Adc,
VGS = 10 Vdc, RG = 9.1 W)
Fall Time
Gate Charge (See Figure 8)
(VDS = 48 Vdc, ID = 23 Adc, VGS = 10 Vdc)
ns
nC
SOURCE−DRAIN DIODE CHARACTERISTICS
Forward On−Voltage
(IS = 23 Adc, VGS = 0 Vdc)
(IS = 23 Adc, VGS = 0 Vdc, TJ = 150°C)
Reverse Recovery Time
(IS = 23 Adc, VGS = 0 Vdc,
dIS/dt = 100 A/ms)
Reverse Recovery Stored Charge
VSD
Vdc
ns
mC
INTERNAL PACKAGE INDUCTANCE
Internal Drain Inductance
(Measured from contact screw on tab to center of die)
(Measured from the drain lead 0.25″ from package to center of die)
LD
Internal Source Inductance
(Measured from the source lead 0.25″ from package to source bond pad)
LS
1. Pulse Test: Pulse Width ≤ 300 ms, Duty Cycle ≤ 2%.
2. Switching characteristics are independent of operating junction temperature.
http://onsemi.com
2
nH
nH
MTP23P06V
TYPICAL ELECTRICAL CHARACTERISTICS
40
VGS = 10V
TJ = 25°C
40
8V
9V
7V
30
6V
20
10
5V
2
4
6
8
100°C
25
20
15
10
2
6
7
Figure 2. Transfer Characteristics
TJ = 100°C
0.12
25°C
0.1
0.08
− 55°C
0.06
0.04
0.02
5
10
15
20
25
30
ID, DRAIN CURRENT (AMPS)
35
40
45
8
0.12
TJ = 25°C
0.115
0.11
0.105
VGS = 10 V
0.1
0.095
15 V
0.09
0.085
0.08
0
Figure 3. On−Resistance versus Drain Current
and Temperature
5
10
15
20
30
35
25
ID, DRAIN CURRENT (AMPS)
40
45
50
Figure 4. On−Resistance versus Drain Current
and Gate Voltage
1.8
100
VGS = 0 V
VGS = 10 V
ID = 11.5 A
I DSS , LEAKAGE (nA)
RDS(on) , DRAIN−TO−SOURCE RESISTANCE
(NORMALIZED)
5
Figure 1. On−Region Characteristics
0.14
1.4
4
VGS, GATE−TO−SOURCE VOLTAGE (VOLTS)
VGS = 10 V
1.6
3
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
0.16
0
25°C
30
0
10
R DS(on) , DRAIN−TO−SOURCE RESISTANCE (OHMS)
R DS(on) , DRAIN−TO−SOURCE RESISTANCE (OHMS)
0
TJ = −55°C
5
4V
0
VDS ≥ 10 V
35
I D , DRAIN CURRENT (AMPS)
I D , DRAIN CURRENT (AMPS)
50
1.2
1
0.8
0.6
TJ = 125°C
10
0.4
0.2
0
−50
−25
0
25
50
75
100 125
TJ, JUNCTION TEMPERATURE (°C)
150
1
175
0
Figure 5. On−Resistance Variation with
Temperature
50
10
20
30
40
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
Figure 6. Drain−To−Source Leakage
Current versus Voltage
http://onsemi.com
3
60
MTP23P06V
POWER MOSFET SWITCHING
Switching behavior is most easily modeled and predicted
by recognizing that the power MOSFET is charge
controlled. The lengths of various switching intervals (Dt)
are determined by how fast the FET input capacitance can
be charged by current from the generator.
The published capacitance data is difficult to use for
calculating rise and fall because drain−gate capacitance
varies greatly with applied voltage. Accordingly, gate
charge data is used. In most cases, a satisfactory estimate of
average input current (IG(AV)) can be made from a
rudimentary analysis of the drive circuit so that
t = Q/IG(AV)
The capacitance (Ciss) is read from the capacitance curve at
a voltage corresponding to the off−state condition when
calculating td(on) and is read at a voltage corresponding to the
on−state when calculating td(off).
At high switching speeds, parasitic circuit elements
complicate the analysis. The inductance of the MOSFET
source lead, inside the package and in the circuit wiring
which is common to both the drain and gate current paths,
produces a voltage at the source which reduces the gate drive
current. The voltage is determined by Ldi/dt, but since di/dt
is a function of drain current, the mathematical solution is
complex. The MOSFET output capacitance also
complicates the mathematics. And finally, MOSFETs have
finite internal gate resistance which effectively adds to the
resistance of the driving source, but the internal resistance
is difficult to measure and, consequently, is not specified.
The resistive switching time variation versus gate
resistance (Figure 9) shows how typical switching
performance is affected by the parasitic circuit elements. If
the parasitics were not present, the slope of the curves would
maintain a value of unity regardless of the switching speed.
The circuit used to obtain the data is constructed to minimize
common inductance in the drain and gate circuit loops and
is believed readily achievable with board mounted
components. Most power electronic loads are inductive; the
data in the figure is taken with a resistive load, which
approximates an optimally snubbed inductive load. Power
MOSFETs may be safely operated into an inductive load;
however, snubbing reduces switching losses.
During the rise and fall time interval when switching a
resistive load, VGS remains virtually constant at a level
known as the plateau voltage, VSGP. Therefore, rise and fall
times may be approximated by the following:
tr = Q2 x RG/(VGG − VGSP)
tf = Q2 x RG/VGSP
where
VGG = the gate drive voltage, which varies from zero to VGG
RG = the gate drive resistance
and Q2 and VGSP are read from the gate charge curve.
During the turn−on and turn−off delay times, gate current is
not constant. The simplest calculation uses appropriate
values from the capacitance curves in a standard equation for
voltage change in an RC network. The equations are:
td(on) = RG Ciss In [VGG/(VGG − VGSP)]
td(off) = RG Ciss In (VGG/VGSP)
4000
C, CAPACITANCE (pF)
Ciss
3000
VGS = 0 V
VDS = 0 V
TJ = 25°C
Crss
2000
Ciss
1000
Coss
Crss
0
10
0
5
VGS
5
10
15
20
25
VDS
GATE−TO−SOURCE OR DRAIN−TO−SOURCE VOLTAGE (VOLTS)
Figure 7. Capacitance Variation
http://onsemi.com
4
30
QT
9
8
27
24
Q2
Q1
VGS
7
21
6
18
5
15
4
12
9
3
2
Q3
1
0
0
5
TJ = 25°C
ID = 23 A
VDS
10
15
25
20
30
35
6
3
0
40
1000
t, TIME (ns)
10
VDS , DRAIN−TO−SOURCE VOLTAGE (VOLTS)
VGS, GATE−TO−SOURCE VOLTAGE (VOLTS)
MTP23P06V
TJ = 25°C
ID = 23 A
VDD = 30 V
VGS = 10 V
100
tr
tf
td(off)
td(on)
10
1
1
10
Qg, TOTAL GATE CHARGE (nC)
RG, GATE RESISTANCE (OHMS)
Figure 8. Gate−To−Source and Drain−To−Source
Voltage versus Total Charge
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
100
DRAIN−TO−SOURCE DIODE CHARACTERISTICS
I S , SOURCE CURRENT (AMPS)
25
TJ = 25°C
VGS = 0 V
20
15
10
5
0
0
0.25
0.5
0.75
1
1.25
1.5
1.75
2
2.25
2.5
VSD, SOURCE−TO−DRAIN VOLTAGE (VOLTS)
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
reliable operation, the stored energy from circuit inductance
dissipated in the transistor while in avalanche must be less
than the rated limit and adjusted for operating conditions
differing from those specified. Although industry practice is
to rate in terms of energy, avalanche energy capability is not
a constant. The energy rating decreases non−linearly with an
increase of peak current in avalanche and peak junction
temperature.
Although many E−FETs can withstand the stress of
drain−to−source avalanche at currents up to rated pulsed
current (IDM), the energy rating is specified at rated
continuous current (ID), in accordance with industry
custom. The energy rating must be derated for temperature
as shown in the accompanying graph (Figure 12). Maximum
energy at currents below rated continuous ID can safely be
assumed to equal the values indicated.
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain−to−source voltage and
drain current that a transistor can handle safely when it is
forward biased. Curves are based upon maximum peak
junction temperature and a case temperature (TC) of 25°C.
Peak repetitive pulsed power limits are determined by using
the thermal response data in conjunction with the procedures
discussed
in
AN569,
“Transient
Thermal
Resistance−General Data and Its Use.”
Switching between the off−state and the on−state may
traverse any load line provided neither rated peak current
(IDM) nor rated voltage (VDSS) is exceeded and the
transition time (tr,tf) do not exceed 10 ms. In addition the total
power averaged over a complete switching cycle must not
exceed (TJ(MAX) − TC)/(RqJC).
A Power MOSFET designated E−FET can be safely used
in switching circuits with unclamped inductive loads. For
http://onsemi.com
5
MTP23P06V
SAFE OPERATING AREA
800
VGS = 20 V
SINGLE PULSE
TC = 25°C
EAS, SINGLE PULSE DRAIN−TO−SOURCE
AVALANCHE ENERGY (mJ)
I D , DRAIN CURRENT (AMPS)
100
100 ms
10
1 ms
10 ms
dc
1
RDS(on) LIMIT
THERMAL LIMIT
PACKAGE LIMIT
600
500
400
300
200
100
0
0.1
0.1
ID = 23 A
700
1
10
VDS, DRAIN−TO−SOURCE VOLTAGE (VOLTS)
25
100
50
75
100
125
150
175
TJ, STARTING JUNCTION TEMPERATURE (°C)
Figure 11. Maximum Rated Forward Biased
Safe Operating Area
Figure 12. Maximum Avalanche Energy versus
Starting Junction Temperature
1.00
r(t), NORMALIZED EFFECTIVE
TRANSIENT THERMAL RESISTANCE
D = 0.5
0.2
0.1
P(pk)
0.10
0.05
0.02
t1
0.01
t2
DUTY CYCLE, D = t1/t2
SINGLE PULSE
0.01
1.0E−05
1.0E−04
1.0E−03
1.0E−02
1.0E−01
t, TIME (s)
Figure 13. Thermal Response
di/dt
IS
trr
ta
tb
TIME
0.25 IS
tp
IS
Figure 14. Diode Reverse Recovery Waveform
http://onsemi.com
6
RqJC(t) = r(t) RqJC
D CURVES APPLY FOR POWER
PULSE TRAIN SHOWN
READ TIME AT t1
TJ(pk) − TC = P(pk) RqJC(t)
1.0E+00
1.0E+01
MTP23P06V
PACKAGE DIMENSIONS
TO−220
CASE 221A−09
ISSUE AB
−T−
B
SEATING
PLANE
C
F
T
S
4
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
A
Q
1 2 3
U
H
K
Z
L
R
V
J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
G
D
N
INCHES
MIN
MAX
0.570
0.620
0.380
0.405
0.160
0.190
0.025
0.035
0.142
0.147
0.095
0.105
0.110
0.155
0.018
0.025
0.500
0.562
0.045
0.060
0.190
0.210
0.100
0.120
0.080
0.110
0.020
0.055
0.235
0.255
0.000
0.050
0.045
−−−
−−−
0.080
STYLE 5:
PIN 1.
2.
3.
4.
MILLIMETERS
MIN
MAX
14.48
15.75
9.66
10.28
4.07
4.82
0.64
0.88
3.61
3.73
2.42
2.66
2.80
3.93
0.46
0.64
12.70
14.27
1.15
1.52
4.83
5.33
2.54
3.04
2.04
2.79
0.508
1.39
5.97
6.47
0.00
1.27
1.15
−−−
−−−
2.04
GATE
DRAIN
SOURCE
DRAIN
E−FET is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
7
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MTP23P06V/D
Similar pages