Maxim DS4510U-15/T Cpu supervisor with nonvolatile memory and programmable i/o Datasheet

Rev 2; 8/04
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
The DS4510 is a CPU supervisor with integrated 64byte EEPROM memory and four programmable, nonvolatile (NV) I/O pins. It is configured with an
industry-standard I 2 C™ interface using either fastmode (400kbps) or standard-mode (100kbps) communication. The I/O pins can be used as general-purpose
I2C-to-parallel I/O expander with unlimited read/write
capability. EEPROM registers allow the power-on value
of the I/O pins to be adjusted to keep track of the system’s state through power cycles, and the CPU supervisor’s timer can be adjusted between 125ms and
1000ms to meet most any application need.
Features
♦ Accurate 5%, 10%, or 15% 5V Power-Supply
Monitoring
♦ Programmable Reset Timer Maintains Reset After
VCC Returns to an In-Tolerance Condition
♦ Four Programmable, NV, Digital I/O Pins with
Selectable Internal Pullup Resistor
♦ 64 Bytes of User EEPROM
♦ Reduces Need for Discrete Components
♦ I2C-Compatible Serial Interface
♦ 10-Pin µSOP Package
Applications
RAM-Based FPGA Bank Switching for
Multiple Profiles
Ordering Information
Industrial Controls
DS4510U-5
VCC TRIP
POINT
5%
Cellular Telephones
DS4510U-10
10%
-40°C to +85°C 10 µSOP
PC Peripherals
DS4510U-15
15%
-40°C to +85°C 10 µSOP
PDAs
DS4510U-5/T&R
5%
-40°C to +85°C 10 µSOP
DS4510U-10/T&R
10%
-40°C to +85°C 10 µSOP
DS4510U-15/T&R
15%
-40°C to +85°C 10 µSOP
PART
Pin Configuration
PINPACKAGE
-40°C to +85°C 10 µSOP
TEMP RANGE
Typical Operating Circuit
2.7V TO 5.5V
TOP VIEW
4.7kΩ
A0 1
SDA
2
SCL
3
VCC
GND
10 RST
DS4510
4
9
I/O0
8
I/O1
7
5
6
I/O2
I/O3
4.7kΩ
FROM
SYSTEM
CONTROLLER
VCC
4.7kΩ
VCC
RST
RESET
A0
I/O0
CONFIG0
SDA
I/O1
CONFIG1 FPGA
I/O2
CONFIG2
I/O3
CONFIG3
GND
DS4510
SCL
GND
µSOP
I2C is a registered trademark of Philips Corp. Purchase of I2C components of Maxim Integrated Products, Inc. or one of its
Associated Companies, conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided
the system conforms to the I2C Standard Specifications as defined by Philips.
______________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
DS4510
General Description
DS4510
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
ABSOLUTE MAXIMUM RATINGS
Voltage Range on VCC, SDA, and SCL
Pins Relative to Ground.....................................-0.5V to +6.0V
Voltage Range on A0, I/O0, I/O1, I/O2, I/O3 Relative
to Ground ..............-0.5V to VCC + 0.5V, not to exceed +6.0V.
Operating Temperature Range ...........................-40°C to +85°C
EEPROM Programming Temperature .....................0°C to +70°C
Storage Temperature Range .............................-55°C to +125°C
Soldering Temperature .......................................See IPC/JEDEC
J-STD-020A Specification
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
RECOMMENDED DC OPERATING CONDITIONS
(TA = -40°C to +85°C)
PARAMETER
SYMBOL
CONDITIONS
Supply Voltage
VCC
(Notes 1)
Input Logic 1
VIH
(Note 2)
Input Logic 0
VIL
MIN
TYP
2.7
0.7 x VCC
-0.3
MAX
UNITS
5.5
V
VCC + 0.3
V
+0.3 x VCC
V
DC ELECTRICAL CHARACTERISTICS
(VCC = 2.7V to 5.5V, TA = -40°C to +85°C.)
PARAMETER
VCC Trip Point
Standby Current
Input Leakage
SDA Low-Level Output Voltage
SYMBOL
VCCTP
ISTBY
DS4510U-5
CONDITIONS
MIN
4.5
DS4510U-10
4.25
DS4510U-15
4.0
VCC = 5.0V (Note 3)
IL
VOL
TYP
4.625
MAX
4.75
UNITS
4.375
4.49
V
4.125
4.24
50
-1.0
75
µA
+1.0
µA
3mA sink current
0.4
6mA sink current
0.6
V
I/OX Low-Level Output Voltage
VOLIOX
4mA sink current
0.4
V
RST Pin Low-Level Output
VOLRST
10mA sink current (Note 4)
0.4
V
6.5
kΩ
10
pF
I/OX Pullup Resistors
I/O Capacitance
2
RP
CI/O
4.0
(Note 5)
_____________________________________________________________________
5.0
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
(VCC = 2.7V to 5.5V, TA = -40°C to +85°C.)
PARAMETER
RST Active Time
SYMBOL
tRST
VCC Detect to RST
tRPU
VCC Fail to RST
tRPD
MIN
TYP
MAX
TD1= 0, TD0 = 0
CONDITIONS
112
125
138
UNITS
TD1= 0, TD0 = 1
225
250
275
TD1= 1, TD0 = 0
450
500
550
TD1= 1, TD0 = 1
900
1000
1100
TD1= 0, TD0 = 0
112
125
138
TD1= 0, TD0 = 1
225
250
275
TD1= 1, TD0 = 0
450
500
550
TD1= 1, TD0 = 1
900
1000
1100
4
10
µs
TYP
MAX
400
UNITS
kHz
ms
ms
AC ELECTRICAL CHARACTERISTICS (See Figure 5)
(VCC = 2.7V to 5.5V, TA = -40°C to +85°C, timing referenced to VIL(MAX) and VIH(MIN).)
PARAMETER
SCL Clock Frequency
Bus Free Time Between Stop and
Start Conditions
SYMBOL
fSCL
CONDITIONS
(Note 6)
MIN
0
tBUF
1.3
µs
tHD:STA
0.6
µs
Low Period of SCL
tLOW
1.3
µs
High Period of SCL
tHIGH
0.6
Data Hold Time
tHD:DAT
0
Data Setup Time
tSU:DAT
100
Start Setup time
tSU:STA
0.6
Hold Time (Repeated) Start
Condition
SDA and SCL Rise Time
SDA and SCL Fall Time
Stop Setup Time
µs
0.9
µs
ns
µs
tR
(Note 7)
20 + 0.1CB
300
ns
tF
(Note 7)
20 + 0.1CB
300
ns
tSU:STO
0.6
SDA and SCL Capacitive
Loading
CB
(Note 7)
EEPROM Write Time
tW
(Note 7)
µs
10
400
pF
20
ms
_____________________________________________________________________
3
DS4510
CPU SUPERVISOR AC ELECTRICAL CHARACTERISTICS (See Figure 1)
NONVOLATILE MEMORY CHARACTERISTICS
(VCC = 2.7V to 5.5V, TA = 0°C to +70°C.)
PARAMETER
SYMBOL
Writes
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
CONDITIONS
MIN
50,000
+70°C (Note 5)
TYP
MAX
UNITS
All voltages referenced to ground.
The DS4510 does not obstruct the SDA and SCL lines if VCC is switched off, as long as the voltages applied to these
inputs do not violate their min and max input voltage levels.
ISTBY specified with VCC equal to 5.0V, and control port-logic pins are driven to ground or VCC for the corresponding
inactive state (SDA = SCL = VCC), does not include pullup resistor current.
See Typical Operating Characteristics for the RST output voltage vs. supply voltage.
This parameter is guaranteed by design.
I2C interface timing shown for is for fast-mode (400kHz) operation. This device is also backward compatible with I 2C
standard-mode timing.
CB—total capacitance of one bus line in picofarads.
EEPROM write time applies to all the EEPROM memory and SEEPROM memory when SEE = 0. The EEPROM write time
begins at the occurrence of a stop condition.
Typical Operating Characteristics
(VCC = +5.0V, TA = +25°C, unless otherwise noted.)
SDA = SCL = VCC
I/O CONTROL BITS = 0
I/O PULLUPS DISABLED
DS4510 toc02
60
40
30
20
10
3.5
4.0
SUPPLY VOLTAGE (V)
4.5
40
30
20
SDA = VCC
10
0
0
3.0
50
SDA = SCL = VCC
30
4
SUPPLY CURRENT vs. SCL FREQUENCY
70
SUPPLY CURRENT (µA)
40
35
50
SUPPLY CURRENT (µA)
45
DS4510 toc01
VCC (10%)
TRIP POINT
SUPPLY CURRENT vs. TEMPERATURE
60
DS4510 toc03
SUPPLY CURRENT vs. SUPPLY VOLTAGE
50
SUPPLY CURRENT (µA)
DS4510
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
5.0
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
_____________________________________________________________________
0
100
200
300
SCL FREQUENCY (kHz)
400
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
RESET TRIP VOLTAGE (V)
4.7
4.6
4.5
4.4
4.3
4.2
4.1
5.0
4.5
5.6kΩ PULLUP
RESISTOR ON RST
SDA = SCL = VCC
4.0
3.5
3.0
2.5
2.0
1.5
1.0
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
5.20
5.15
5.10
5.05
5.00
4.95
4.90
4.85
4.80
0.5
0
4.0
DS4510 toc06
4.8
I/O PULLUP RESISTANCE vs. TEMPERATURE
5.25
I/O PULLUP RESISTANCE (kΩ)
DS4510 toc04
4.9
VCC TRIP POINT (V)
RST OUTPUT VOLTAGE vs. SUPPLY VOLTAGE
6.0
5.5
DS4510 toc05
VCC TRIP POINT vs. TEMPERATURE
5.0
4.75
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
-40
SUPPLY VOLTAGE (V)
-20
0
20
40
60
80
TEMPERATURE (°C)
Pin Description
PIN
NAME
FUNCTION
I2C Address Input. This input pin determines the chip address of the device. A0 = 0 sets the slave
address to 1010000b, A0 = 1 sets the slave address to 1010001b.
1
A0
2
SDA
Serial Data Input/Output. Bidirectional I2C data pin.
3
SCL
Serial Clock Input. I2C clock input.
4
VCC
Power Input
5
GND
Ground
6
I/O3
Input/Output 3. I2C accessible bidirectional I/O pin.
7
I/O2
Input/Output 2. I2C accessible bidirectional I/O pin.
8
I/O1
Input/Output 1. I2C accessible bidirectional I/O pin.
9
I/O0
Input/Output 0. I2C accessible bidirectional I/O pin.
10
RST
Active-Low Reset Output. Open-drain CPU supervisor reset output.
_____________________________________________________________________
5
DS4510
Typical Operating Characteristics (continued)
(VCC = +5.0V, TA = +25°C, unless otherwise noted.)
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
DS4510
Functional Diagram
VCC
SDA
SCL
DS4510
2-WIRE
INTERFACE
RST
A0
VCC
VCC
PROGRAMMABLE
RESET
TIMER
INTERNAL
VOLTAGE
REFERENCE
4x
GND
EEPROM
64 BYTES
USER
MEMORY
VCC
4 BIDIRECTIONAL
NONVOLATILE I/O LATCHES
RP
PULLUP ENABLE (F0h)
4 NV
I/O PINS
I/OX CONTROL (F4h-F7h)
I/O STATUS (F8h)
Detailed Description
The DS4510 contains a CPU supervisor, four programmable I/O pins, and a 64-byte EEPROM memory. All
functions are configurable or controllable through an
industry-standard I2C-compatible bus. DS4510 NV registers that are likely to require frequent modification are
implemented using SRAM-shadowed EEPROM (SEEPROM) memory. This memory is configurable to act as
volatile SRAM or NV EEPROM by adjusting the SEE bit
in the Config register. Configuring the SEEPROM as
SRAM eliminates the EEPROM write time and allows
infinite write cycles to these registers. Configuring the
registers as EEPROM allows the application to change
the power-on values that are recalled during power-up.
Programmable CPU Supervisor
The timeout period is adjusted by writing the reset
delay register (SEEPROM). The delay for each setting
is shown in the CPU Supervisor AC Electrical
Characteristics. If the SEE bit is set, changes are written to SRAM. On power-up the last value written to the
EEPROM is recalled. The I2C bus is also used to activate the RST by setting the SWRST bit in the Config
register. This bit automatically returns to zero after the
timeout period. The Config register also contains the
ready, trip point, and reset status bits. The ready bit
6
determines if the power-on reset level of the DS4510 is
surpassed by VCC. The trip point bit determines if VCC
is above VCCTP, and the reset status bit is set if RST is
in its active state.
Note: The RST pin is an open-drain output, therefore an
external pullup resistor must be used to realize high
logic levels.
Programmable NV Digital I/O Pins
Each programmable I/OX pin contains an input, opencollector output, and a selectable internal pullup resistor. The DS4510 stores changes to the I/O X pin in
SEEPROM memory. Using the SEEPROM as SRAM is
conducive to applications such as I/O expansion that
generally require fast access times and frequent modification of the I/OX pin. Configuring the SEEPROM to
behave as EEPROM allows the modification of the
power-on state of the I/OX pin. During power-up the
I/OX pins are high impedance until VCC exceeds 2.0V
(typically), which is when the last value programmed is
recalled from EEPROM. On power-down, the I/OX state
is maintained until VCC drops below 1.9V (typically).
The internal pullups for each I/OX pin are controlled by
the pullup-enable register (F0h). Similarly, the individual
I/OX control registers (F4h to F7h) adjust the pulldown
_____________________________________________________________________
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
tR
User Memory
Three types of memory are present in the DS4510
(EEPROM, SEEPROM, and SRAM). The main user
memory is 64 bytes of EEPROM starting at address
00h. This memory is not SRAM shadowed, so all writes
to these locations result in EEPROM write cycles
regardless of the state of the SEE bit. Additional memory for storing application data includes 6 bytes of SRAM
(FAh–FFh), and 2 bytes of SEEPROM (F2h, F3h). Refer
to the register memory map (Figure 3) for register
addresses and memory types. Figure 4 shows the bit
names for the memory-mapped I/O bytes and their factory default values.
The higher-order bits of the I/O registers that are not
used, such as the four most significant bits of the
pullup-enable byte (address F0h), can be used as
additional memory. It is the responsibility of the application to ensure that writes to these bytes do not
adversely affect bits controlling special functions of the
DS4510.
VCCTP (MIN)
DS4510
transistors. Read the I/O status register (F8h) to determine the logic levels present at the I/O pins.
tF
VCCTP (MAX)
VCCTP
VCCTP (MAX)
VCCTP
tRPU
VCCTP (MIN)
tRPD
VOH
VOL
Figure 1. CPU Supervisor Power-Up and Power-Down Timing
REGISTER ADDRESS (HEX)
F8
MEMORY TYPE
SRAM
I/O STATUS
REGISTER NAME
Figure 2. How to Read the Memory Map
00
USER BYTE
08
USER BYTE
10
USER BYTE
18
USER BYTE
20
USER BYTE
28
USER BYTE
30
USER BYTE
38
USER BYTE
40
EE 02
User byte
EE 0A
USER BYTE
EE 12
USER BYTE
EE 1A
USER BYTE
EE 22
USER BYTE
EE 2A
USER BYTE
EE 32
USER BYTE
EE 3A
USER BYTE
42
EE 03
USER BYTE
EE 0B
USER BYTE
EE 13
USER BYTE
EE 1B
USER BYTE
EE 23
USER BYTE
EE 2B
USER BYTE
EE 33
USER BYTE
EE 3B
USER BYTE
43
E9
EA
SEE F2
F1
RESET DELAY
USER BYTE
F9
SRAM FA
CONFIG
USER BYTE
EB
SEE F3
USER BYTE
SRAM FB
USER BYTE
EE 01
USER BYTE
EE 09
USER BYTE
EE 11
USER BYTE
EE 19
USER BYTE
EE 21
USER BYTE
EE 29
USER BYTE
EE 31
USER BYTE
EE 39
USER BYTE
41
EE 04
USER BYTE
EE 0C
USER BYTE
EE 14
USER BYTE
EE 1C
USER BYTE
EE 24
USER BYTE
EE 2C
USER BYTE
EE 34
USER BYTE
EE 3C
USER BYTE
44
EE 05
USER BYTE
EE 0D
USER BYTE
EE 15
USER BYTE
EE 1D
USER BYTE
EE 25
USER BYTE
EE 2D
USER BYTE
EE 35
USER BYTE
EE 3D
USER BYTE
45
EE 06
USER BYTE
EE 0E
USER BYTE
EE 16
USER BYTE
EE 1E
USER BYTE
EE 26
USER BYTE
EE 2E
USER BYTE
EE 36
USER BYTE
EE 3E
USER BYTE
46
EE 07
USER BYTE
EE 0F
USER BYTE
EE 17
USER BYTE
EE 1F
USER BYTE
EE 27
USER BYTE
EE 2F
USER BYTE
EE 37
USER BYTE
EE 3F
USER BYTE
47
EE
EE
EE
EE
EE
EE
EE
EE
RESERVED
E8
F0
SEE
PULLUP ENABLE
F8
SRAM
I/O STATUS
EC
SEE F4
SEE
I/O3 CONTROL
SRAM FC
SRAM
USER BYTE
ED
F5
SEE
I/O2 CONTROL
FD
SRAM
USER BYTE
EE
F6
SEE
I/O1 CONTROL
FE
SRAM
USER BYTE
EF
F7
SEE
I/O0 CONTROL
FF
SRAM
USER BYTE
*ITALICIZED BYTES HAVE BIT DESCRPTIONS, REFER TO FIGURE 3.
Figure 3. Register Memory Map
_____________________________________________________________________
7
DS4510
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
REGISTER
REGISTER
LOCATION
NAME
(HEX)
REGISTER BIT NAMES
FACTORY OR
POWER-ON
DEFAULT
(BIN)
Bit 7
Bit 6
Bit5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
EE
EE
EE
EE
00000000
User
EEPROM
00-3F
EE
EE
EE
EE
Reserved
40-EF
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
I/O2
pullup
I/O1
pullup
I/O0
pullup
00000000
Pullup
Enable
F0
SEE
SEE
SEE
SEE
I/O3
pullup
RST Delay
F1
SEE
SEE
SEE
SEE
SEE
SEE
TD1
TD0
00000011
User SEE
F2
SEE
SEE
SEE
SEE
SEE
SEE
SEE
SEE
00000000
User SEE
F3
SEE
SEE
SEE
SEE
SEE
SEE
SEE
SEE
00000000
I/O3
Control
F4
SEE
SEE
SEE
SEE
SEE
SEE
SEE
I/O3
00000001
I/O2
Control
F5
SEE
SEE
SEE
SEE
SEE
SEE
SEE
I/O2
00000001
I/O1
Control
F6
SEE
SEE
SEE
SEE
SEE
SEE
SEE
I/O1
00000001
I/O0
Control
F7
SEE
SEE
SEE
SEE
SEE
SEE
SEE
I/O0
00000001
I/O Status
F8
0
0
0
0
I/O3
Status
I/O2
Status
I/O1
Status
I/O0
Status
n/a
Config
F9
ready
trip point
reset
status
SEE
SWRST
0
0
0
XXX00000
User SRAM
FA-FF
SRAM
SRAM
SRAM
SRAM
SRAM
SRAM
SRAM
SRAM
00000000
Figure 4. Register Bit Names
I2C Definitions
The following terminology is commonly used to
describe I2C data transfers.
Master Device: The master device controls the slave
devices on the bus. The master device generates SCL
clock pulses, start, and stop conditions.
Slave Devices: Slave devices send and receive data
at the master’s request.
Bus Idle or Not Busy: Time between stop and start
conditions when both SDA and SCL are inactive and in
their logic-high states. When the bus is idle it often initiates a low-power mode for slave devices.
Start Condition: A start condition is generated by the
master to initiate a new data transfer with a slave.
Transitioning SDA from high to low while SCL remains
high generates a start condition. See the timing diagram for applicable timing.
Stop Condition: A stop condition is generated by the
master to end a data transfer with a slave. Transitioning
8
SDA from low to high while SCL remains high generates a stop condition. See the I2C Timing Diagram for
applicable timing.
Repeated Start Condition: The master can use a
repeated start condition at the end of one data transfer
to indicate that it will immediately initiate a new data
transfer following the current one. Repeated starts are
commonly used during read operations to identify a
specific memory address to begin a data transfer. A
repeated start condition is issued identically to a normal start condition. See the I2C Timing Diagram for
applicable timing.
Bit Write: Transitions of SDA must occur during the low
state of SCL. The data on SDA must remain valid and
unchanged during the entire high pulse of SCL (see
Figure 5) plus the setup and hold-time requirements.
Data is shifted into the device during the rising edge of
the SCL.
Bit Read: At the end a write operation, the master must
release the SDA bus line for the proper amount of setup
_____________________________________________________________________
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
DS4510
Table 1. Register Definitions
REGISTER
LOCATION (HEX)
REGISTER
NAME
FUNCTION
00 to 3F
User EEPROM
64 bytes of EEPROM memory.
40 to EF
Reserved
These memory locations are reserved for future products.
F0
Pullup Enable
The four least significant bits of this register each enable/disable one of the internal pullup
resistors. Set the bit to enable the pullup, clear it to disable the pullup.
F1
RST Delay
The two LSBs of this register (TD1 and TD0) select the reset delay (tRST) as shown in the
CPU Supervisor AC Timing Characteristics.
F2 to F3
User SEEPROM
SRAM Shadowed EEPROM user byte.
F4 to F7
I/OX Control
Clearing the LSB of the register enables the I/OX pulldown transistor; setting the bit disables
the pulldown transistor.
F8
I/O Status
This register reflects the logic level of the I/OX pins. The upper four bits of this register
always read zero.
F9
Config
This register contains 5 bits that read and control the behavior of the part as follows:
FA to FF
Bit Name
Bit Function
ready
Reads zero when VCC is above the DS4510's power-on reset voltage.
Trip Point
Reads one when VCC below VCCTP.
Reset Status
Reads one when the RST pin is active.
SEE
When zero, writes to the SEEPROM registers behave like EEPROM. When one, writes to the
SEEPROM registers behave like SRAM.
SWRST
Setting this bit activates the RST output. This bit automatically returns to zero during the
RST active time.
User SRAM
6 bytes of SRAM memory
time (see Figure 5) before the next rising edge of SCL
during a bit read. The device shifts out each bit of data
on SDA at the falling edge of the previous SCL pulse
and the data bit is valid at the rising edge of the current
SCL pulse. Remember that the master generates all
SCL clock pulses, including when it is reading bits from
the slave.
Acknowledgement (ACK and NACK): An
Acknowledgement (ACK) or Not Acknowledge (NACK)
is always the 9th bit transmitted during a byte transfer.
The device receiving data (the master during a read or
the slave during a write operation) performs an ACK by
transmitting a zero during the 9th bit. A device performs a NACK by transmitting a one during the 9th bit.
Timing (Figure 5) for the ACK and NACK is identical to
all other bit writes. An ACK is the acknowledgment that
the device is properly receiving data. A NACK is used
to terminate a read sequence or as an indication that
the device is not receiving data.
Byte Write: A byte write consists of 8 bits of information transferred from the master to the slave (most significant bit first) plus a 1-bit acknowledgement from the
slave to the master. The 8 bits transmitted by the master are done according to the bit-write definition and the
acknowledgement is read using the bit-read definition.
Byte Read: A byte read is an 8-bit information transfer
from the slave to the master plus a 1-bit ACK or NACK
from the master to the slave. The 8 bits of information
that are transferred (most significant bit first) from the
slave to the master are read by the master using the
bit-read definition above, and the master transmits an
ACK using the bit-write definition to receive additional
data bytes. The master must NACK the last byte read
to terminate communication so the slave will return control of SDA to the master.
Slave Address and the R/W Bit: Each slave on the I2C
bus responds to a slave addressing byte sent immediately following a start condition. The slave address byte
contains the slave address and the R/W bit. The slave
address (see Figure 6) is the most significant 7 bits and
the R/W bit is the least significant bit.
The DS4510’s slave address is 101000A0 (binary),
where A 0 is the value of the A 0 address pin. The
_____________________________________________________________________
9
DS4510
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
SDA
tBUF
tHD:STA
tR
tLOW
tSP
tF
SCL
tHD:STA
STOP
tSU:STA
tHIGH
tSU:DAT
START
tHD:DAT
REPEATED
START
tSU:STO
NOTE: TIMING IS REFERENCE TO VIL(MAX) AND VIH(MIN)
Figure 5. I2C Timing Diagram
address pin allows for the DS4510 to respond to one of
two slave addresses (1010000X, or 1010001X). If the
R/W bit is zero, the master writes data to the slave. If
the R/W is one, the master reads data from the slave.
Memory Address: During an I2C write operation, the
master must transmit a memory address to identify the
memory location where the slave is to store the data.
The memory address is always the second byte transmitted during a write operation following the slave
address byte (R/W = 0).
7-BIT SLAVE ADDRESS
1 0
MOST
SIGNIFICANT BIT
1
0
0
0 A0 R/W
A0 PIN
VALUE
DETERMINES
READ OR WRITE
Figure 6. DS4510’s Slave Address and the R/W Bit
10
I2C Communications
Writing a Single Byte to a Slave: The master must
generate a start condition, write the slave address
(R/W= 0), write the memory address, write the byte of
data and generate a stop condition. Remember the
master must read the slave’s acknowledgement during
all byte write operations.
Writing a Multiple Bytes to a Slave: To write multiple
bytes to a slave the master generates a start condition,
writes the slave address (R/W = 0), writes the memory
address, writes up to 8 data bytes, and generates a
stop condition.
The DS4510 can write 1 to 8 bytes (one page or row)
with a single write transaction. This is internally controlled by an address counter that allows data to be
written to consecutive addresses without transmitting a
memory address before each data byte is sent. The
address counter limits the write to one 8-byte page
(one row of the memory table, see Figure 3). Attempts
to write to additional pages of memory without sending
a stop condition between pages results in the address
counter wrapping around to the beginning of the present row.
Example: A 3-byte write starts at address 06h and
writes three data bytes (11h, 22h, and 33h) to three
“consecutive” addresses. The result would be addresses 06h and 07h would contain 11h and 22h, respectively, and the third data byte, 33h, would be written to
address 00h.
To prevent address wrapping from occurring, the master must send a stop condition at the end of the page,
then wait for the bus-free or EEPROM-write time to
elapse. The master may then generate a new start con-
____________________________________________________________________
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
Reading a Single Byte from a Slave: Unlike the write
operation that uses the memory address byte to define
where the data is to be written, the read operation
occurs at the present value of the memory address
counter. To read a single byte from the slave the master generates a start condition, writes the slave address
with R/W = 1, reads the data byte with a NACK to indicate the end of the transfer, and generates a stop condition.
Manipulating the Address Counter for Reads: A
dummy write cycle can be used to force the address
counter to a particular value. To do this the master generates a start condition, writes the slave address (R/W
= 0), writes the memory address where it desires to
read, generates a repeated start condition, writes the
slave address (R/W = 1), reads data with ACK or NACK
as applicable, and generates a stop condition.
See Figure 7 for a read example using the repeated
start condition dummy write cycle.
Reading Multiple Bytes from a Slave: The read operation can be used to read multiple bytes with a single
transfer. When reading bytes from the slave, the master
simply ACKs the data byte if it desires to read another
byte before terminating the transaction. After the master reads the last byte it NACKs to indicate the end of
the transfer and generates a stop condition. This can
be done with or without modifying the address
counter’s location before the read cycle. The DS4510
does not wrap on page boundaries during read operations, but the counter rolls from its upper-most memory
address FFh to 00h if the last memory location is read
during the read transaction.
Example: The entire memory contents of the DS4510
can be read with a single transfer starting at address
F0h that reads 80 bytes of data. Addresses F0h to FFh
are read sequentially, the address counter rolls to 00h,
and then addresses 00h to 3Fh can be read sequentially. This allows the entire memory contents to be read in
a single operation without reading the undefined contents of the reserved area of the memory.
Application Information
Advantages of Using the SEE Bit to Disable
EEPROM Writes
The SEE bit allows EEPROM writes to be disabled for
the SRAM-shadowed EEPROM bytes, allowing the
SRAM of SEE registers to change without writing the
EEPROM to the same value. This prevents write operations from changing the power-on value of the I/O pins,
reduces the number of EEPROM write cycles, and
speeds up I/O operations because the DS4510 does
not require an internally timed EEPROM write cycle to
complete the operation.
Power-Supply Decoupling
To achieve the best results when using the DS4510,
decouple the power supply with a 0.01µF or a 0.1µF
capacitor. Use high-quality, ceramic, surface-mount
capacitors, and mount the capacitors as close as possible to the VCC and GND pins of the DS4510 to minimize lead inductance.
SDA and SCL Pullup Resistors
SDA is an open-collector output on the DS4510 that
requires a pullup resistor to realize high logic levels.
Because the DS4510 does not utilize clock cycle
stretching, a master using either an open-collector output with a pullup resistor or a normal output driver can
be utilized for SCL. Pullup resistor values should be
chosen to ensure that the rise and fall times listed in the
AC Electrical Characteristics are within specification.
____________________________________________________________________
11
DS4510
dition, write the slave address (R/W = 0), and the first
memory address of the next page before continuing to
write data.
Acknowledge Polling: Any time an EEPROM page is
written, the DS4510 requires the EEPROM write time
(tW) after the stop condition to write the contents of the
page to EEPROM. During the EEPROM write time, the
DS4510 does not acknowledge its slave address
because it is busy. It is possible to take advantage of
that phenomenon by repeated addressing the DS4510,
which allows the next page to be written as soon as the
DS4510 is ready to receive the data. The alternative to
acknowledge polling is to wait for maximum period of
tW to elapse before attempting to write again to the
DS4510.
EEPROM Write Cycles: When EEPROM writes occur,
the DS4510 writes the whole EEPROM memory page
even if only a single byte on the page was modified.
Writes that do not modify all 8 bytes on the page are
allowed and do not corrupt the remaining bytes of
memory on the same page. Because the whole page is
written, bytes on the page that were not modified during the transaction are still subject to a write cycle. This
can result in a whole page being worn out over time by
writing a single byte repeatedly. Writing a page one
byte at a time wears the EEPROM out eight times faster
than writing the entire page at once. The DS4510’s
EEPROM memory is guaranteed to handle 50,000 write
cycles at +70°C. Writing to SEEPROM memory with
SEE = 1 does not count as an EEPROM write cycle
when evaluating the EEPROM’s estimated lifetime.
DS4510
CPU Supervisor with Nonvolatile Memory and
Programmable I/O
COMMUNICATIONS KEY
NOTES:
S
START
A
ACK
WHITE BOXES INDICATED THE MASTER IS
CONTROLLING SDA
P
STOP
N
NOT
ACK
SHADED BOXES INDICATED THE SLAVE IS
CONTROLLING SDA
Sr
REPEATED
START
X X
X X
X X
X X
1) ALL BYTES ARE SENT MOST SIGNIFICANT
BIT FIRST.
2) THE FIRST BYTE SENT AFTER A START
CONDITION IS ALWAYS THE SLAVE ADDRESS
FOLLOWED BY THE READ/WRITE BIT.
8-BITS ADDRESS OR DATA
WRITE A SINGLE BYTE
S
1
0 1
0 0
0 A0 0
MEMORY ADDRESS
A
A
DATA
A
A
DATA
A
P
WRITE UP TO AN 8-BYTE PAGE WITH A SINGLE TRANSACTION
S
1
0 1
0 0
0 A0 0
MEMORY ADDRESS
A
DATA
A
P
READ A SINGLE BYTE WITH A DUMMY WRITE CYCLE TO MOVE THE ADDRESS COUNTER
S
1
0 1
0 0
0 A0 0
MEMORY ADDRESS
A
A
Sr
1 0
1 0 0
0 A0 1
A
DATA
N
1 0 0
0 A
A
DATA
A
P
READ MULTIPLE BYTES WITH A DUMMY WRITE CYCLE TO MOVE THE ADDRESS COUNTER
S
1
0 1
0 0
0 A0 0
MEMORY ADDRESS
A
DATA
A
Sr
DATA
A
1 0
A
0
1
DATA
N
P
Figure 7. I2C Communications Examples
Chip Topology
TRANSISTOR COUNT: 16559
SUBSTRATE CONNECTED TO GROUND
Package Information
For the latest package outline information, go to
www.maxim-ic.com/DallasPackInfo.
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2004 Maxim Integrated Products
Printed USA
is a registered trademark of Dallas Semiconductor Corporation.
is a registered trademark of Maxim Integrated Products.
Similar pages