PCA EPA366-5 Smd 14 pin gull-wing quad ttl compatible active delay module Datasheet

SMD 14 Pin Gull-Wing Quad TTL Compatible
Active Delay Modules
DELAY TIME
±5% or ±2 nS†
5
6
7
8
9
10
11
12
13
14
15
†Whichever is greater.
PART
NUMBER
DELAY TIME
±5 or ±2 nS†
PART
NUMBER
DELAY TIME
±5% or ±2 nS†
PART
NUMBER
EPA366-5
EPA366-6
EPA366-7
EPA366-8
EPA366-9
EPA366-10
EPA366-11
EPA366-12
EPA366-13
EPA366-14
EPA366-15
16
17
18
19
20
21
22
23
24
25
30
EPA366-16
EPA366-17
EPA366-18
EPA366-19
EPA366-20
EPA366-21
EPA366-22
EPA366-23
EPA366-24
EPA366-25
EPA366-30
35
40
45
50
55
60
65
70
75
EPA366-35
EPA366-40
EPA366-45
EPA366-50
EPA366-55
EPA366-60
EPA366-65
EPA366-70
EPA366-75
Delay times referenced from input to leading edges at 25°C, 5.0V, with no load.
DC Electrical Characteristics
Parameter
Test Conditions
VOH
VOL
VIK
IIH
High-Level Output Voltage
Low-Level Output Voltage
Input Clamp Voltage
High-Level Input Current
IIL
IOS
Low-Level Input Current
Short Circuit Output Current
ICCH
ICCL
TRO
NH
NL
High-Level Supply Current
Low-Level Supply Current
Output Rise Time
Fanout High-Level Output
Fanout Low-Level Output
VCC = min. VIL = max. I OH = max
VCC = min. VIH = min. IOL= max
VCC = min. II = IIK
VCC = max. VIN = 2.7V
VCC = max. VIN = 5.25V
VCC = max. VIN = 0.5V
VCC = max. VOUT = 0.
(One output at a time)
VCC = max. VIN = OPEN
VCC = max. VIN = 0
2.7
-40
VCC = max. VOH = 2.7V
VCC = max. VOL = 0.5V
Recommended
Operating Conditions
VCC
VIH
VIL
IIK
IOH
IOL
PW*
d*
TA
Schematic
Min Max Unit
Supply Voltage
High-Level Input Voltage
Low-Level Input Voltage
Input Clamp Current
High-Level Output Current
Low-Level Output Current
Pulse Width of Total Delay
Duty Cycle
Operating Free-Air Temperature
0.5
-1.2V
50
1.0
-2
-100
V
V
V
µA
mA
mA
mA
14
8
4
5
7 GROUND
Max
Unit
4.75
2.0
5.25
V
V
V
mA
mA
mA
%
%
°C
0.8
-18
-1.0
20
40
0
40
+70
.055
.400
Max.
PCA
EPA366-5
Date Code
.280
Max.
Suggested Solder
Pad Layout
.410
.03
.100
.780 Max.
.01
Typ.
Unit
3.2
110
2.0
1.0
100
5.0
.02
.100
.050
.300
Volts
%
nS
MHz
KHz
Volts
QAF-CSO1 Rev. B 8/25/94
DSA366 Rev. A 2/5/96
Unless Otherwise Noted Dimensions in Inches
Tolerances:
Fractional = ± 1/32
16 .XX = ± .030 .XXX = ± .010
3
Package Dimensions
Min
Input Pulse Test Conditions @ 25° C
VCC
10
9
.250
Max.
Pulse Input Voltage
Pulse Width % of Total Delay
Pulse Rise Time (0.75 - 2.4 Volts)
Pulse Repetition Rate @ Td ≤ 200 nS
Pulse Repetition Rate @ Td > 200 nS
Supply Voltage
12
1
150
mA
150
mA
4
nS
20 TTL LOAD
10 TTL LOAD
*These two values are inter-dependent.
EIN
PW
TRI
PRR
VCC
ELECTRONICS
INC.
16799 SCHOENBORN ST.
NORTH HILLS, CA 91343
TEL: (818) 892-0761
FAX: (818) 894-5791
Similar pages