ams AS8530 Lin transceiver with integrated voltage regulator and mcu interface for automotive application Datasheet

Datasheet
AS8530
LIN Tr a ns ce i ve r w it h I nt eg ra t e d Volt a ge Re gul at or a nd
MCU Interface for Automotive Applications
1 General Description
Typically 45µA quiescent current in standby mode,
Typically 35µA quiescent current in sleep mode
The AS8530 is a general purpose companion IC for sensor and
actuator LIN slaves offering LIN transceiver and low drop voltage
regulator.
Under voltage reset with factory options
LIN bus transceiver l conforming to LIN 2.1, TX time out fail
safe feature, over temperature warning and shut down
It also provides a 2-wire microcontroller interface through shared EN
and TX pins to access a window watchdog with RC oscillator, control
registers, backup registers and monitoring information.
Window watchdog if factory enabled
Micro controller 2-wire interface through shared pins for
watchdog trigger, monitoring, register read /write
The IC is fabricated in a high voltage CMOS technology which is
able to withstand voltages up to 42V.
Chip ID for traceability and module ID
The product is available in ep-SOIC8 package.
8 Backup registers to store data during VCC shut down
ep-SOIC8 package
2 Key Features
-40ºC to +125ºC ambient operating temperature
Operating voltage 6V to 18V
3 Applications
Linear, low-drop voltage regulator: VCC = 5V ±5% or 3.3V ±5%
as a factory programming option
The AS8530 is a System Basis Chip for automotive LIN networked
sensor or actuator slaves.
50mA load current
Operating modes: Normal and Standby or Normal and Sleep as
a factory option
Figure 1. AS8530 LIN Transceiver Block Diagram
VCC
LDO
VSUP
POR-VSUP
Temperature
Limiter
AS8530
TSHD
RESET_VSUP_N
EN
2-Wire
Interface
Window
Watchdog
(WWD)
RESET_VCC_N
Mode
Control
RESET_VSUP_N
Control
Signals
WWD Output
LIN
Wakeup
Reset
Block
RESET
Receiver
VSUP
RX
30k
VCC
Transmitter
LIN
15k
Slew
Control
GND
POR-VCC
TX
LIN Transceiver
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
1 - 32
AS8530
Datasheet - C o n t e n t s
Contents
1 General Description ..................................................................................................................................................................
1
2 Key Features.............................................................................................................................................................................
1
3 Applications...............................................................................................................................................................................
1
4 Pin Assignments .......................................................................................................................................................................
4
4.1 Pin Descriptions....................................................................................................................................................................................
4
5 Absolute Maximum Ratings ......................................................................................................................................................
5
6 Electrical Characteristics...........................................................................................................................................................
6
6.1 Operating Conditions............................................................................................................................................................................
6
6.2 Digital Inputs and Outputs ....................................................................................................................................................................
6
6.3 Detailed System and Block Specifications ...........................................................................................................................................
7
6.3.1 Electrical System Specifications .................................................................................................................................................. 7
6.4 Low Dropout Regulator.........................................................................................................................................................................
7
6.5 LIN Transceiver ....................................................................................................................................................................................
8
6.5.1
6.5.2
6.5.3
6.5.4
DC Electrical Characteristics ....................................................................................................................................................... 8
AC Electrical Characteristics ....................................................................................................................................................... 9
Temperature Limiter .................................................................................................................................................................. 10
TX Timeout Watchdog ............................................................................................................................................................... 10
6.6 VCC Undervoltage Reset and Window Watchdog..............................................................................................................................
11
6.7 Two Port Serial Interface ....................................................................................................................................................................
12
7 Detailed Description................................................................................................................................................................
13
7.1 Voltage Regulator (LDO) ....................................................................................................................................................................
13
7.2 Temperature Limiter............................................................................................................................................................................
13
7.3 VSUP Undervoltage Reset .................................................................................................................................................................
13
7.3.1 VSUP Undervoltage in Normal Mode......................................................................................................................................... 13
7.3.2 VSUP Undervoltage in Standby Mode / Sleep Mode................................................................................................................. 13
7.3.3 VSUP Undervoltage in Low Slew Mode..................................................................................................................................... 13
7.4 RESET................................................................................................................................................................................................
14
7.5 VCC Undervoltage Reset ...................................................................................................................................................................
14
7.6 Window Watchdog (WWD) .................................................................................................................................................................
14
7.7 LIN Transceiver ..................................................................................................................................................................................
15
7.8 Operating Modes and States..............................................................................................................................................................
7.8.1
7.8.2
7.8.3
7.8.4
7.8.5
Normal Mode .............................................................................................................................................................................
Standby Mode............................................................................................................................................................................
Sleep Mode................................................................................................................................................................................
Temporary Shutdown Mode ......................................................................................................................................................
Thermal Shutdown State ...........................................................................................................................................................
7.9 State Diagram.....................................................................................................................................................................................
8 Application Information ...........................................................................................................................................................
15
15
15
15
16
16
17
18
8.1 Initialization.........................................................................................................................................................................................
18
8.2 Wake-Up.............................................................................................................................................................................................
19
8.3 Over-Temperature Shutdown .............................................................................................................................................................
19
8.4 LIN BUS Transceiver ..........................................................................................................................................................................
19
8.4.1 Transmit Mode........................................................................................................................................................................... 19
8.4.2 Receive Mode............................................................................................................................................................................ 20
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
2 - 32
AS8530
Datasheet - C o n t e n t s
8.5 RX and TX Interface ...........................................................................................................................................................................
20
8.6 MODE Input EN..................................................................................................................................................................................
21
8.7 Serial Port Interface............................................................................................................................................................................
23
8.7.1 Device Configuration using 2-Wire Serial Port .......................................................................................................................... 23
8.8 Control and Diagnosis Registers ........................................................................................................................................................
26
8.8.1 Definition of Control and Status Registers................................................................................................................................. 26
9 Package Drawings and Markings ...........................................................................................................................................
28
10 Ordering Information.............................................................................................................................................................
31
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
3 - 32
AS8530
Datasheet - P i n A s s i g n m e n t s
4 Pin Assignments
Figure 2. Pin Assignments (Top View)
EN
1
8
VCC
VSUP
2
7
RESET
AS8530
LIN
3
6
TX
VSS
4
5
RX
4.1 Pin Descriptions
Table 1. Pin Descriptions
Pin Number
Pin Name
Pin Type
Special Requirements
Description
1
EN
Digital input with
pull-down
2kV ESD
Enable high-voltage compatible pin with pull down
to VSS and ½ VCC trigger level, active high.
2
VSUP
Supply pad
Load dump (42V max),
4kV HBM ESD,
Jump start (27V max)
3
LIN
Analog I/O
Conforms to LIN 2.1,
6kV HBM ESD
4
VSS
Supply pad
5
RX
Digital output with
pull-up
6
TX
Digital input with
pull-up
7
RESET
Digital output
8
VCC
Supply pad
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Battery supply
LIN Bus
LIN transceiver receive signal, data out in test
mode
2kV ESD
LIN transceiver transmit signal, clock in test mode
Digital output referenced to VCC, active low
Regulated 5V / 3.3V supply for loads up to 50mA.
OTP selectable
Revision 1.1
4 - 32
AS8530
Datasheet - A b s o l u t e M a x i m u m R a t i n g s
5 Absolute Maximum Ratings
Stresses beyond those listed in Table 2 may cause permanent damage to the device. These are stress ratings only, and functional operation of
the device at these or any other conditions beyond those indicated in Electrical Characteristics on page 6 is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Table 2. Absolute Maximum Ratings
Parameter
Min
Max
Units
Comments
-0.3
42
V
Transient up to 500ms duration
EN
-0.3
VSUP +
0.3
V
VCC
-0.3
7
V
LIN
-27
+40
V
RESET, RX, TX
-0.3
VCC + 0.3
V
-100
100
mA
Electrical Parameters
VSUP
DC Supply Voltage
Input current (latchup immunity) Iscr
Norm: JEDEC 78
Electrostatic Discharge
Electrostatic Discharge (ESD)
Norm: AEC-Q-100-002
±2
For on board signals VCC, TX, RX, Reset
kV
±4
±6
For VSUP
LIN to VSS, HBM Model
Continuous Power Dissipation
Total operating power dissipation
(all supplies and outputs) Pt
0.25
W
+150
ºC
epSOIC8 in still air, soldered on JEDEC standard
board @125º ambient, static operation = no time limit
Temperature Ranges and Storage Conditions
Storage temperature (Tstrg)
-55
Package body temperature (Tbody)
Humidity non-condensing
5
Moisture Sensitive Level
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
+260
ºC
85
%
3
The reflow peak soldering temperature (body
temperature) specified is in accordance with IPC/
JEDEC J-STD-020 “Moisture/Reflow Sensitivity
Classification for Non-Hermetic Solid State Surface
Mount Devices”.
The lead finish for Pb-free leaded packages is matte
tin (100% Sn).
Represents a maximum floor life time of 168h
Revision 1.1
5 - 32
AS8530
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6 Electrical Characteristics
6.1 Operating Conditions
Symbol
Parameter
Conditions
Min
VSUP
Positive Supply Voltage
Normal operating condition
6
VSS
Negative Supply Voltage
TAMB
Ambient temperature
Maximum junction temperature (TJ) 150ºC
-40
Isupp
Supply Current
Typ
Max
Units
18
V
+125
ºC
65
mA
Max
Units
0
V
6.2 Digital Inputs and Outputs
All pull-up, pull-downs have been implemented with active devices. RESET and RX have been measured with 100pF load.
Symbol
Parameter
Conditions
Min
Typ
EN Input
High Voltage Pin which can also be
connected to VSUP
VIH
High level input voltage
VIL
Low level input voltage
ILEAK
Input leakage current
EN = L
Ipd_en
Pull down current
EN = VCC
0.8VCC
V
0.2VCC
V
-1
+1
µA
20
40
µA
TX
VIH
High level input voltage
0.8VCC
V
VIL
Low level input voltage
0.2VCC
V
ILEAK
Input leakage current
TX = VCC
-1
+1
µA
Ipu
Pull up current
TX pulled to VSS
-30
-10
µA
RESET
VOH
High level output voltage
IOUT = 1 mA, VSUP ≥ 6V
VOL
Low level output voltage
VSUP ≥ 6V
VCC 0.5
V
VSS
+ 0.4
V
RX
VOH
High level output voltage
VOL
Low level output voltage
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
VCC 0.5
IOUT = 1 mA, VSUP ≥ 6V
Revision 1.1
V
VSS +
0.4
V
6 - 32
AS8530
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6.3 Detailed System and Block Specifications
6.3.1
Electrical System Specifications
Symbol
Parameter
1
Current
consumption
Min
Typ
Max
Units
No load on VCC, LIN recessive, VSUP= 12V
300
µA
No load on VCC, LIN dominant, VSUP = 12V
700
µA
Stand-by mode
Up to 125°C ambient (no load), VSUP= 12V
45
µA
Sleep mode
Up to 125°C ambient (no load), VSUP=12V
35
µA
Normal mode
IDDnom
Conditions
1. No external load on the LIN bus
6.4 Low Dropout Regulator
The LDO block is a linear voltage regulator, which provides a regulated (band-gap stabilized) output voltage (VCC) from the battery supply
voltage (VSUP).
(6V < VSUP < 18V for option 1, 6V <VSUP <18V option2; -40°C < TJ < 150°C; all voltages are with respect to ground (VSS); positive current
flows into the pin), normal operating mode if not otherwise mentioned.
Symbol
Parameter
Conditions
Min
Typ
Max
VCC
Regulated supply voltage
ILOAD 0mA to 50mA
Option 1
4.75
5.25
Option 2
3.135
3.465
Units
V
TJ
Junction Temperature
-40
150
ºC
VSUP
Supply Voltage Range
6
12
18
V
Load < 50mA
4.75
5.0
5.25
50mA to 65mA
4.5
5.5
Standby mode @ ICC < 5mA
4.5
5.5
Option 1
VCC
Load-dump condition,
ILOAD < 50mA
Output Voltage Range
Option 2
5.5
Load < 50mA
3.135
3.3
3.465
50mA to 65mA
2.97
3.3
3.63
Standby mode @ ICC < 5mA
2.97
Load-dump condition,
ILOAD < 50mA
V
3.63
3.63
Normal mode
50
250
Standby mode
5
250
ICC_SH
Output Short Circuit Current
dVCC1
Line Regulation
ΔVCC / ΔVSUP
8
mV/V
LOREG_SM
Load Regulation (Standby mode)
ΔVCC / ΔICCn (for ILOAD > 500µA)
10
mV/mA
LOREG_NM
Load Regulation (Normal mode)
ΔVCC / ΔICCn (for ILOAD > 500µA)
1
mV/mA
2.2
10
µF
1
10
Ω
CL1
ESR1
CL2
ESR2
CSUP1E
ESR1_CSUP
CSUP2C
ESR2_CSUP
Output Capacitor (Electrolytic)
Output Capacitor (Ceramic)
Input capacitor (Electrolytic)
For EMC suppression
Input capacitor (Ceramic)
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
mA
100
220
nF
0.02
1
Ω
10
100
µF
1
10
Ω
100
220
nF
0.02
1
Ω
7 - 32
AS8530
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6.5 LIN Transceiver
6.5.1
DC Electrical Characteristics
(4.5V < VCC < 5.5V; 6V < VSUP < 18V; -40°C < TJ < 150°C, VBUS is the voltage on the LIN node. All voltages are with respect to ground (VSS);
positive current flows into the pin.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
40
120
200
mA
2
V
60
kΩ
20
µA
Driver
1
Ibus_lim
Current limitation in Dominant State
LIN = VSUP_max
LIN_VOL
Output Voltage BUS (dominant state),
ILIN = 40mA
(short-circuit condition tested at VOL = 2.5V)
Pull-up resistor
Normal mode
(recessive BUS level on TX pin)
20
Driver OFF;
VSUP = 7.0V, 8V < VBUS < 18
Ibus_leak_rec
40
Receiver
Ibus_leak_dom
Input Leakage current at receiver
Ibus_no_GND
Ibus_no_bat
Input Leakage current at receiver
Driver OFF; Vbus = 0V; VSUP = 12V;
VCC = 5V
-1
VSS = VSUP; VSUP = 12V;
2
0V < VBUS < 18V, VCC = 5V
-1
VSUP = VSS;
0V < VBUS < 18V, VCC = VSS
2
Vbus_dom
Vbus_rec
mA
1
mA
100
µA
0.4
VSUP
0.6
Vbus_cnt
Vbus_cnt = (Vth_dom + Vth_rec)/2
Vhys
Vhys = (Vth_dom – Vth_rec)
3
VSUP
0.475
0.525
VSUP
0.05
0.175
VSUP
3
1. This failure condition triggers thermal shut down when shut down temperature threshold is exceeded.
2. Not production tested.
3. Vth_dom: Receiver threshold of the recessive to dominant LIN bus edge
Vth_rec : Receiver threshold of the dominant to recessive LIN bus edge
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
8 - 32
AS8530
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6.5.2
AC Electrical Characteristics
LIN Driver, Bus load conditions (CBUS ; RBUS): 1nF; 1kΩ / 6,8nF; 660Ω / 10nF; 500Ω
Symbol
Conditions
Min
Typ
Max
Units
D1
(worst case 20Kbps transmission)
Vth_rec(max) = 0.744 x VSUP;
Vth_dom(max) = 0.581 x VSUP;
VSUP = 6.0V to 18V; tbit = 50μs;
D1 = tbus_rec(min) / (2 x tbit)
0.369
D2
(worst case 20kbps transmission)
Vth_rec (min) = 0.422 x VSUP;
Vth_dom (min) = 0.284 x VSUP;
VSUP = 6V to 18V; tbit = 50μs;
D2 = tbus_rec(max) / (2 x tbit)
D3
(worst case 10.4kbps transmission)
Vth_rec (max) = 0.778 x VSUP;
Vth_dom (max) = 0.616 x VSUP;
VSUP = 6.0V to 18V; tbit = 96μs;
D3 = tbus_rec(min) / (2 x tbit)
D4
(worst case 10.4kbps transmission)
Vth_rec (min) = 0.389 x VSUP;
Vth_dom (min) = 0.251 x VSUP;
VSUP = 6V to18V; tbit = 96μs;
D4 = tbus_rec(max) / (2 x tbit)
0.59
tdLR
VCC = 5V;
Propagation delay bus dominant to RX LOW
6
µs
tdHR
VCC = 5V;
Propagation delay bus dominant to RX HIGH
6
µs
tRS
Receiver Delay symmetry
-2
2
µs
twake
Wake-up delay time
30
150
µs
tsln
Transition from standby mode to normal mode
(clock frequency is 128kHz ± 25%)
4
Clock cycles
tnsl
Transition from normal mode to standby mode
(clock frequency is 128kHz ± 25%)
6
Clock cycles
trec_deb
Receiver De-bounce time
Cint
Guaranteed by design
0.581
0.417
1
220
3
µs
250
pF
Note: Sleep-mode to Normal mode transition is identical to the Power-ON sequence after the remote wakeup event on LIN bus. The
transition time will include the tRes (RESET time) and start-up time for the LDO.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
9 - 32
AS8530
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
Figure 3. LIN Timing
tbit
tbit
TXD
tbus_dom(max)
tbus_rec(min)
tbus_dom(min)
tbus_rec(max)
LIN
Vth_rec(max)
Vth_dom(max)
Vth_rec(min)
Vth_dom(min)
6.5.3
Temperature Limiter
Symbol
Parameter
Conditions
Min
Tsd
Shut down temperature
Junction temperature
Tret
Max
Units
139
171
ºC
Return temperature
During shut down, the sensor must be
powered by VSUP.
Thermal shut down disables LDO and sets
all drivers to high impedance, the IC returns
from shut down with POR.
121
149
ºC
Totset
Over-temp warning flag set
The temperature beyond which the warning
flag is set.
121
149
ºC
Totclear
Over-temp warning flag clear
The return temperature when the warning
flag is cleared
103
127
ºC
6.5.4
Typ
TX Timeout Watchdog
Symbol
Parameter
tlin_wdog
Time out duration (dominant state)
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Conditions
Revision 1.1
Min
Typ
Max
Units
0.5
1
2
s
10 - 32
AS8530
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6.6 VCC Undervoltage Reset and Window Watchdog
The values in this table are valid for normal and standby modes. All parameters are tested, unless mentioned otherwise.
Symbol
Parameter
Conditions
Min
Vuvr_off
VCC under-voltage threshold off
(Default)
Rising edge of VCC
Vuvr_on
VCC under voltage threshold on
(Default)
Vuvr1_off
VCC under voltage threshold off
(Factory Option)
Rising edge of VCC
Vuvr1_on
VCC under voltage threshold on
(Factory Option)
Vuvr2_off
Max
Units
2.55
2.95
V
Falling edge of VCC
2.3
2.7
V
1
3.0
3.4
V
Falling edge of VCC
1
2.75
3.15
V
VCC under voltage threshold off
(Factory Option)
Rising edge of VCC
1
3.5
3.9
V
Vuvr2_on
VCC under voltage threshold on
(Factory Option)
Falling edge of VCC
1
3.25
3.65
V
Vuvr3_off
VCC under-voltage threshold off
(Factory Option)
Rising edge of VCC
1
4.0
4.4
V
Vuvr3_on
VCC under voltage threshold on
(Factory Option)
Falling edge of VCC
1
3.75
4.15
V
Vhyst_vcc
Hysteresis of under-voltage threshold
on/off VCC
Default and all other factory options
0.1
0.4
V
trr
Spike filter on VCC
To remove disturbance
4
Vsuvr_off
VSUP under-voltage threshold off
Vsuvr_on
VSUP under-voltage threshold on
WD_TCL
WWD non-service time
(if factory enabled)
WD_TSV
WWD Service – time
(if factory enabled)
tRes
Reset delay time
Tshd
Temporary shutdown reset active time
BOR level (considered to be the Master
Reset for AS8530)
RESET will be generated
12
RESET will not be generated
1
4ms, 16ms, 32ms (typ) are factory options
(min = -25% and max = +50% of typical)
0-75
75-150
6
0.1
Typ
0.25
µs
3.85
V
3.25
V
0 -100
0-125
100-200 125-250
8
ms
ms
12
ms
1
s
1. These are factory options which could be made available on specific request.
2. -40%, -20%, +20%, +60%, and +100% timings are available as factory options.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
11 - 32
AS8530
Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s
6.7 Two Port Serial Interface
Symbol
Parameter
Conditions
Min
Typ
Max
Units
250
Kbps
General
BR2WIRE_SPI
Bit rate
TENSCLK_H
Clock high time
2
µs
TENSCLK_L
Clock low time
2
µs
tDI_SU
Data in setup time
20
ns
tDI_HD
Data in hold time
10
ns
tDO_S
Data out setup time
130
ns
tDO_HD
Data out hold time
135
ns
tDO_D
Data out delay
tDI_HZ
Data in to high impedance delay
Write timing
Read timing
Time for the Microcontroller to release
the TX bus
80
ns
80
ns
Timing parameters when entering 2-Wire SP mode
Ttx_su
TX setup time before EN goes Low
20
ns
Ttx_hd
TX hold time after EN goes High
20
ns
Ttx_SP_trigger
EN falling edge to TX falling edge
To enter into 2-Wire SP mode
2
TSTNDY_trigger
TX high time from EN falling edge
To enter into Sleep/Standby mode
5
cycles
Ten_ENSCLK
EN falling edge to start of 2-wire serial
port clock
5
cycles
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
10
µs
12 - 32
AS8530
Datasheet - D e t a i l e d D e s c r i p t i o n
7 Detailed Description
The AS8530 chip consists of a low drop-out regulator and a LIN bus transceiver, which is a bi-directional bus interface for data transfer between
LIN bus and the LIN protocol controller. Additionally integrated is a RESET unit with a power-on-reset delay and a programmable window
watchdog. It also includes a watchdog time-out on LIN TX node to indicate if the microcontroller is stuck in a loop and to release unintentional
LIN bus dominant state.
7.1 Voltage Regulator (LDO)
The voltage regulator has three operating modes. The features of the operating modes are given below:
Normal mode: Stability to be better ±0.25V over input range and temperature for load current up to 50mA. The LDO Output provides a
voltage of 5V or 3.3V as OTP option.
Standby mode: The Standby mode is a low quiescent current mode used in car applications that are always switched on. The load current
in standby mode is 5mA. Quiescent current (no load) is less than 45mA typically at room temperature.
Sleep mode: Power down or temporary shutdown of the regulator can be set by a register bit. This bit can be written through 2-wire MCU
interface.
The LDO takes the input from bandgap and scales it up to the required voltage. The LDO starts charging only after the POR-VSUP event occurs
(RESET_VSUP_N switched from low to high). The LDO can be powered-down by a control signal (temporary shutdown register) for the
temporary shutdown mode.
7.2 Temperature Limiter
Temperature limiter produces a power down when temperature exceeds 155ºC ±10%. It powers up and generates a reset when it returns to
135ºC ±10% junction temperature. During thermal shut down, temperature sensor is supplied by VSUP. During the temperature ramp-up phase,
as soon as the temperature exceeds 135ºC ±10%, a warning signal is issued and is written into the diagnostic register, which can be read
through the SP interface.
7.3 VSUP Undervoltage Reset
VSUP undervoltage reset generates a reset RESET_VSUP_N, switched from low to high when VSUP ramps up above VSUVR_OFF. This is
used to enable proper initialization of mode control and diagnostic registers. If VSUP < VSUVR_ON, then RESET_VSUP_N switches from high
level to low level (active). This is considered to be the master reset and will have the highest priority over all other signals. As soon as VSUP <
VSUVR_ON, the LDO, LIN Transceiver is completely shut off and system comes to a complete stop. AS8530 enters into the normal operating
mode only after VSUP > VSUVR_OFF.
7.3.1
VSUP Undervoltage in Normal Mode
Supply Voltages below VSUVR_OFF and above VSUVR_ON do not influence the voltage regulator. The output voltage VCC follows VSUP.
7.3.2
VSUP Undervoltage in Standby Mode / Sleep Mode
No exit from the sleep mode or standby mode take place if the VSUP voltage drops down to VSUVR_OFF. If VSUP goes below VSUVR_ON,
RESET_VSUP_N is active and resets the mode control and diagnostic register. The voltage regulator, LIN Transceiver modules are turned off. If
VSUP rises again above VSUVR_OFF, RESET_VSUP_N is switched from low to high. The system enters normal mode where LIN Transceiver
and LDO are switched on.
7.3.3
VSUP Undervoltage in Low Slew Mode
The behavior of AS8530 at low VSUP voltages is equal to the sleep mode. The low slew mode (set by control register through serial interface as
an option) will be cancelled, if VSUP drops below VSUVR_ON in this mode. The AS8530 enters the normal mode, if VSUP rises again above
VSUVR_OFF.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
13 - 32
AS8530
Datasheet - D e t a i l e d D e s c r i p t i o n
7.4 RESET
Reset generates an external RESET signal to reset the microcontroller and all other external circuits. The reset functionality is illustrated in
Figure 4. Reset consists of a digital buffer at the output. RESET signal can be affected by RESET_VCC_N (which is the under-voltage reset on
VCC) and Window watchdog output. All those conditions which cause a drop in the VCC voltage will be detected from the low voltage reset unit,
which in-turn generates a reset signal. States like Temporary shut-down, Over-temperature monitor will influence the RESET output through
RESET_VCC_N signal only.
Figure 4. Reset Functionality
VSUP
T>Tj
VCC
T<Tj
t<trr
VUVR_OFF
VUVR_ON
tRes
tRes
tRes
trr
RESET
Initialization
Thermal shutdown
Spike VSUP
MISSING
WATCHDOG
ACCESS
tRes
Low voltage VSUP
tRes
Current limitation active
7.5 VCC Undervoltage Reset
The POR-VCC generates RESET_VCC_N signal as output which determines under-voltage reset of the output of the LDO. The rising edge of
the VCC gives an under-voltage reset “off” and the falling edge of the VCC gives an under-voltage reset “on”. This under-voltage signal is used to
control the RESET output. When VCC rises up Vuvr_off for a period greater than reset duration (tRes) then RESET_VCC_N switches from low
level to high level and pin RESET is inactive (high). If VCC falls below Vuvr_on for a period greater than a predetermined delay (trr) then
RESET_VCC_N switches from high level to low level and pin RESET is active (low). The RESET_VCC_N signal is used to initializes Window
watchdog timer, TX time-out, Test control circuits, 2-wire SP, and logic associated with SP (everything other than the SP control registers). VCC
under-voltage reset threshold voltage level adjustment can be made by 2 bit OTP as explained in OTP interface.
7.6 Window Watchdog (WWD)
To keep the external microcontroller always in proper function state, a window watchdog circuit is implemented. The WWD trigger is generated
by external MCU through SP interface. If the window is missed, a reset on the RESET pin with certain reset time (tRes) is generated. The WWD
function can be enabled or disabled by factory setting. The watchdog is started after the ASSP exits reset. Under normal working conditions,
microcontroller gives a WWD trigger every time in the window period of WD_TSV (service time). If the trigger does not occur during WD_TSV or
occurs too early during WD_TCL (non-service time), then RESET output is pulled low (active), which will reset the micro-controller. WWD circuit
is turned on after the RESET pin goes back to high (inactive). If VCC < Vuvr_on, WWD circuit is switched off. When the WWD function is
enabled, there is a 3-bit factory programming available to set the trigger window.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
14 - 32
AS8530
Datasheet - D e t a i l e d D e s c r i p t i o n
Figure 5. Window Watchdog Trigger
Period
Non-Service time (WD_TCL)
Service time (WD_TSV)
50 %
100 %
Trigger restart period
Trigger via SPI
Last trigger point
Earliest possible trigger point
(System will not RESET)
Latest possible trigger point
(System will not be RESET)
Valid Trigger point
(System will not be RESET)
Unwanted trigger point
(System will be RESET)
7.7 LIN Transceiver
The transceiver provides short circuit limitation, hardware watchdog and over temperature shut down features. The TX watchdog timer is active
when TX is pulled low (active). As soon as the TX watchdog timeout occurs, the LIN bus is released from dominant state to recessive state. The
LIN transceiver has a pull-up resistor (for the slave node; extra resistor externally for the master node) to the VSUP. A diode protection is
available to protect it from back supply from bus line.
The LIN transmitter has the basic functionality of relaying the data from the micro-controller on to the LIN. The data on the LIN needs to have
controlled slew to have reduced EMI. The receiver relays the data from the LIN to the micro-controller. This transmitter has optimized EMC
performance across different loading conditions conforming to the LIN 2.1 standards. The wake-up detects a wake up event on the LIN.
7.8 Operating Modes and States
The AS8530 provides four main operating modes “normal”, “sleep/stand-by” (programmed by OTP), “temporary shutdown” and “thermal
shutdown”. The LIN transceiver can be programmed to operate with lower slew in the normal mode. Refer to Table 3 for a detailed description on
transition for each mode.
7.8.1
Normal Mode
This is the mode after the power-up. In normal mode, LDO, LIN Transceiver, Window Watchdog, Resistive divider and the line drivers are all
turned on. All the blocks are completely functional. LDO is now capable of delivering maximum load current possible as per the device
specifications. The LIN Transceiver is capable of sending the TX data from microcontroller to the LIN bus at a maximum rate of 20Kbps. EN
signal is set to high and LIN, TX, RX pins can be driven into dominant (low) or recessive (high) states. If the junction temperature increases more
than Totset, a warning flag is set in the diagnostic register, which can be read through the 2-wire interface.
7.8.2
Standby Mode
Standby mode is a functional low-power mode where LIN Transceiver is disabled. The LIN wake-up circuit and over-temperature monitor circuit
is enabled. Window watchdog, TX timeout watchdog, Resistive divider, relay driver circuits are disabled. EN pin held low in this mode. TX pin is
in recessive state (high). CS is pulled to VCC while SDI and SCLK outputs are pulled to VSS.
7.8.3
Sleep Mode
As a factory programming option on request the AS8530 offers as a replacement to the standby mode with sleep mode. Sleep mode is the most
current saving mode. If EN is held low, the LDO, LIN Transceiver and the reset and window watchdog unit will be switched off. VCC is pulled
down to zero. The LIN wake-up circuit, oscillator and over-temperature monitor circuit is active. LIN bus is in recessive state (high). Only wakeup possible is through remote wake-up, through LIN pin, pulling it to dominant state for 100µs typical (low), can change the state of the system.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
15 - 32
AS8530
Datasheet - D e t a i l e d D e s c r i p t i o n
7.8.4
Temporary Shutdown Mode
In this mode, the VCC is pulled down and the LDO is powered down. This mode is introduced to interface with other components which do not
have a pin for the reset functionality. This provides an alternative way to reset those components interfacing with AS8530. This mode is default
disabled but can be enabled by an OTP option. In this mode, all internal modules supplied by the LDO are disabled. Only the oscillator, control
registers are enabled. The VCC output can be temporarily switched off and pulled to VSS. EN signal, RX, TX is pulled low and LIN Transceiver
along with the LIN wake-up circuit is powered down. No remote wake-up functionality is possible. LIN bus enters into recessive state. The
system goes out of this mode to normal mode after the time-out of an internal counter delay (Tshd). Normal mode to temporary shutdown
transition will be controller by register bit in configuration register.
7.8.5
Thermal Shutdown State
If the junction temperature TJ is higher than Tsd, the AS8530 will be switched into the thermal shutdown mode. The transceiver is completely
disabled. No wake-up functionality is available. Window watchdog, TX timeout watchdog, and LDO are completely turned off. Only the overtemperature monitor would be working. As soon as the temperature returns back to Tret, the system enters normal mode. For more information
on transition, see Table 3.
Table 3. Transition Table
Transition
From mode
Interface
To mode
LIN
RX
Stand-By
X-RS
X-H
Sleep
X-RS
X-H
Temporary
Shutdown
X-RS
X-H
OverTemperature
X-RS
X-H
Normal (LW)
X
H-X
Normal (RW)
X
Temporary
Shutdown
RS
H
OverTemperature
RS
H
Normal
RS-X
H-X
Normal
RS-X
OverTemperature
RS
H
Power Off
X
1
Normal
Mode
Stand-By
Mode
Temporary
Shutdown
Mode
2
2
TX
H
H
3
3
Reg.
0x05
D0
rwake
Uvbat
OT
Uvcc
3
L
X
X
inactive
inactive
TX is high for
TSTNDY_triggerr
3
L
X
X
inactive
set
TX is high for
1
TSTNDY_triggerr
The Control Bit is set
through the 2-Wire SP
interface
EN
H-L
H-L
Flags
2
X
H
3
H
X
X
inactive
set
2
X
X
L
X
X
set
set
2
X
L-H
L
X
X
inactive
inactive
H-X
2
H
X
L
set
X
inactive
Remote Wake up
inactive Event
occurred on LIN
2
H
L
H
X
X
inactive
set
2
H
L
L
X
X
set
set
2
X
X
L
X
X
inactive
clear
Internal 128ms timer
expired
H-X
2
X
X
L
set
X
inactive
clear
Remote Wake up
Event occurred on LIN
2
X
X
L
X
X
set
hold
Temperature monitor
output asserted
(covered by scan)
X
X
X
X
X
L-H
X
X
3
3
3
Sleep Mode
All States
Comments
3
The Control Bit is set
through the 2-Wire SP
interface
1. Chosen by factory programming option
2. Effect of Transition
3. Cause for Transition
Note: L = low state, H = high state, OT = Over-temperature Reset, Uvcc = Undervoltage VCC, Uvbat = Undervoltage VBAT, rwake =remote
wake, X = do not care.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
16 - 32
AS8530
Datasheet - D e t a i l e d D e s c r i p t i o n
7.9 State Diagram
The complete functional state machine for AS8530 is illustrated in Figure 6. Some soft-states in the FSM like “TXWD Wait”, “Standby Wait” and
other “wait” states have been included for the sake of completeness.
Figure 6. Finite State Machine Model for the AS8530 System
INIT0
Vsup > Vsuvr_off
Temperature < Tret
OVTEMP
OTP LOAD
otp_load
Temperature > Tsd
128msec
Temperature > Tsd
Temporary
Shutdown
RESET TIMEOUT
Tem
shu porar
tdo y
wn
RESET time >
tRES
Vcc < Vuvr_on ||
wwdtimeout
rwake
Temperature > Tsd
y
ar
or n
mp ow
Te hutd
s
y
ndb
sta
rwake
orary
Temp wn
o
shutd
Temperature > Tsd
STANDBY WAIT
Vcc < Vuvr_on
RX=0
WAIT_TEST
otp
_en
RX
=0
ary
por n
Tem utdow
sh
STANDBY
NORMAL
by
and
! st
Vcc < Vuvr_on
rw
ak
e_
wa
it
Temperature > Tsd
test_en
Standby &
sleep
TX=1
SLEEP
Txwd_timeout
Temperature > Tsd
WAIT_OTP
Vcc < Vuvr_on ||
wwdtimeout
TXWD WAIT
Temperature > Tsd
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
17 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8 Application Information
8.1 Initialization
When the power supply is switched on, if VSUP > VSUVR_OFF, RESET_VSUP_N becomes inactive (high). After this, the voltage regulator
starts with a default LDO output setting of 3.3V and Vuvr_off setting of 2.75V. If VCC > Vuvr_off (2.75V), active-low PORN_2_OTP is generated.
The rising edge of PORN_2_OTP loads contents of fuse onto the OTP latch after load access time TLoad. LOAD_OTP_IN_PREREG signal loads
contents of OTP latch onto the pre-regulator domain register. This register gives actual settings of LDO, Vuvr_off and Reset Timeout period TRes.
This is done because the OTP block is powered by the VCC. If VCC > Vuvr_off (phase 2), Reset timeout is restarted. RESET signal is deasserted after Reset Timeout period TRes (phase 2) and then device enters into normal mode. The circuit initializes correctly also for very slow
ramp on VSUP (of the order of 0.5V/min).
Figure 7. Initialization Sequence for AS8530
Vsuvr_off
VSUP
RESET_VSUP_N
PHASE 1
Device
Settings
LDO
Off
PHASE 2
LDO On
Vuvr_off = 2.75V, LDO setting = 3.3V
tRES = 4msec
LDO On
Vuvr_off = from OTP Block, LDO setting = from OTP Block
tRES = from OTP Block
Vuvr_off
Vuvr_off
VCC
RESET_VCC_N
PORN_2_OTP
6 Cycles of
RC-Oscillator
LOAD_OTP_IN_PREREG
RESET
If Phase 1 POR threshold != Phase 2 POR threshold
Tres = Reset Timeout from OTP Block
If Phase 1 POR threshold == Phase 2 POR threshold
Tres = Reset Timeout from OTP Block
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
18 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Table 4. VSUP>Vsuvr_on and VCC<Vuvr_on
Block
Output Signal
TRANSCEIVER = Enabled (disabled only during initial VSUP ramp-up)
LIN = high-z, RX = follows V
LDO = Enabled (disabled only during initial ramp-up)
VCC = low
RELAY DRIVER = Enabled
LDRIVE1 = high, LDRIVE2 = high
RESET = Enabled
RESET = high-z
RESISTIVE DIVIDER = Enabled
VBAT= high, VBAT_DIV = enabled
Block
Output Signal
TRANSCEIVER = Disabled
LIN = high-z, RX = high-z
LDO = Disabled
VCC = low
RELAY DRIVER = Disabled
LDRIVE1 = high, LDRIVE2 = high
RESET = Disabled
RESET = high-z
RESISTIVE DIVIDER = Disabled
VBAT = high, VBAT_DIV = low
Table 5. VSUP<Vsuvr_on
8.2 Wake-Up
If the regulator is put into sleep/standby mode, it can be woken up with the BUS interface. A transition on the BUS (high to low) with a minimum
predefined low time (twake) puts the regulator into normal mode.
8.3 Over-Temperature Shutdown
If the junction temperature increases beyond Tsd the over-temperature recognition will be activated and the regulator voltage will be switched off.
The VCC voltage drops down, the reset state is entered and the bus transceiver is switched off (recessive state). After TJ falls below Tret, the
AS8530 will be initialized again. This initialization starts independently from the voltage levels on EN and BUS. Within the thermal shutdown
mode, the transceiver cannot switch to the normal mode either with local or with remote wake-up. The operation of the AS8530 is possible
between TJ (125ºC) and the switch off temperature Tsd, but small parameter differences can appear. After over-temperature switch-off, the IC
initializes as explained in Initialization on page 18. The low slew mode for LIN Transceiver has to be selected again on re-initialization, if
necessary.
8.4 LIN BUS Transceiver
The AS8530 has an integrated bi-directional bus interface device for data transfer between LIN bus and the LIN protocol controller. The
transceiver consists of a driver with slew rate control, wave shaping and current limitation and a receiver with high voltage comparator followed
by a de-bouncing unit.
8.4.1
Transmit Mode
During transmission the data at the pin TX will be transferred to the BUS driver to generate a bus signal. To minimize the electromagnetic
emission of the bus line, the BUS driver has an integrated slew rate control and wave shaping unit.
Transmitting will be interrupted in the following cases:
Sleep mode
Thermal Shutdown active
Master Reset (VSUP < Vsuvr_on)
The recessive BUS level is generated from the integrated 30k pull up resistor in serial with an active diode This diode prevents the reverse
current of VBUS during differential voltage between VSUP and BUS (VBUS>VSUP). No additional termination resistor is necessary to use the
AS8530 in LIN slave nodes. If this IC is used for LIN master nodes it is necessary that the BUS pin is terminated via an external 1kΩ resistor in
series with a diode to VBAT.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
19 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.4.2
Receive Mode
The data signals from the BUS pin will be transferred continuously to the pin RX. Short spikes on the bus signal are suppressed by the
implemented de-bouncing circuit. Including all tolerances the LIN specific receive threshold values of 0.4*VSUP and 0.6*VSUP will be securely
observed.
Figure 8. Receive Mode Impulse Diagram
Vthr_max
60%
BUS
Vthr_hys
Vthr_cnt
50%
40%
Vthr_min
t < tdeb_BUS
t < tdeb_BUS
RX
8.5 RX and TX Interface
Input TX.
The 5V input TX controls directly the BUS level. LIN Transmitter acts like a slew-controlled level shifter. A dominant state (low) on TX leads to the
LIN bus being pulled low (dominant state) too. The TX pin has an internal active pull up connected to VCC. This guarantees that an open TX pin
generates a recessive BUS level.
Figure 9. TX Input Circuitry
MCU
AS8530
VCC
VCC
IPU_TXD
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
TX
Revision 1.1
RC-Filter
(10ns)
20 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Output RX.
The received BUS signal will be output to the RX pin:
BUS < Vthr_cnt – 0.5 * Vthr_hys → RX = low
BUS > Vthr_cnt + 0.5 * Vthr_hys → RX = high
This output is a push-pull driver between VCC and GND with an output current of 1mA.
Figure 10. RX Output Circuitry
AS8530
MCU
VCC
RX
8.6 MODE Input EN
The AS8530 is switched from normal mode to the standby/sleep mode with a falling edge on EN and keeping TX high for TSTNDY_trigger time.
Device is switched from standby mode to normal mode with a rising edge at the EN pin. The mode change for AS8530 with a falling edge at EN
can be done independently from the state of the bus transceiver. Device enters into Serial port mode by forcing EN low and driving TX high to low
within Ttx_SP_trigger time after EN forced to low.
This ensures the direct control of device to enter into Standby/Sleep mode by microcontroller using EN pin.
Figure 11. EN Pin Functionality
Entry into Serial
Port Mode
Ten_ENSCLK
EN
RD LEN LEN
A4
WR
1
0
TX
Ttx_su
Normal
Mode
TSTNDY_trigger
Ttx_hd
Standby/Sleep
Mode
D3
D2
D1
D0
Ttx_su
Ttx_SP_trigger
Normal Mode
Serial Port Mode
Normal Mode
The EN input has an internal active pull down to secure that if this pin is not connected, a low level will be generated.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
21 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Figure 12. Enable Controlled via. MCU
Cload
EN
VSUP
LIN
AS8530
VBAT
VCC
+
MCU
+ 5V
RESET
TX
VSS
RX
If the application doesn’t need the wake up capability of the AS8530, a direct connection EN to VCC is possible. In this case the AS8530
operates in permanent normal mode. Also possible is the external (outside of the module) control of the EN line via. VSUP signal as shown
below.
Figure 13. Permanent Normal Mode
Cload
EN
VSUP
LIN
AS8530
VBAT
VCC
+ 5V
RESET
VSS
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
+
MCU
TX
RX
Revision 1.1
22 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.7 Serial Port Interface
The interface is essentially used to trigger the window watchdog, to access test mode and read out diagnostic information for the AS8530. The
description of this interface and the protocol is explained below. Information on block status and errors can be displayed by diagnosis registers.
8.7.1
Device Configuration using 2-Wire Serial Port
The AS8530 device configuration register is programmed via a 2-wire Serial Programming Interface. EN/SCL is used as Serial Clock and TX/
SDA_IO is used as Serial Data. EN is used as clock input to access serial port registers in serial port mode. Also EN is used to control transition
from normal mode to standby/sleep mode. The TX input of the device will be multiplexed as following:
LIN TX for transmitting data from microcontroller on LIN bus
SDA_IO for Serial data input/output, this will be used for serially accessing data from configuration and status register
SP Frame. A frame is formed by first byte for command and address/configuration and following bit stream that can be formed by an integer
number of bytes. Command is coded RD/WR on the first bits, length of the transfer is indicated by LEN1, LEN2 bits while address is given on
LSB 5 bits.
Table 6. Command Bits
Command Bits
Register Address or Transmission Configuration
RD/WR
LEN1
LEN2
A4
A3
A2
A1
A0
RD/WR
Command
<A4:A0>
Description
0
WRITE
ADDRESS
Writes data byte on the given starting address.
1
READ
ADDRESS
Read data byte from the given starting address.
Table 7. Transfer Length
LEN1
LEN2
Length
Description
0
0
1
Transfer consists of single Data phase. After completion of single Data phase device comes out of Serial
port interface.
0
1
2
Transfer consist of two Data phase.
1
0
4
Transfer consist of four Data phase.
1
1
8
Transfer consist of eight Data phase.
Write Command. For Write command RD/WR = 0
After the command code, length of the transfer is send in next two bits, the address of register to be written has to be provided from the MSB to
the LSB. Then one, two, four, or eight data bytes can be transferred from the MSB to the LSB. For each data byte following the first one, used
address is the incremented value of the previously written address. Each bit of the frame has to be driven by the 2-Wire SP master on the SP
clock (EN pin) positive edge and the 2-Wire SP slave (device) samples this bit on the next SP clock (EN pin) negative edge. In the following
figures two examples of write command (without and with address self-increment).
Figure 14. Protocol for Serial Data Write with Length = 1
EN
TX
0
LEN1
LEN0
A4
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
Data Phase
Command & Address Phase
LEN1 = 0 LEN0 = 0
Length of Transaction = 1
Transfer edge
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Sampling edge
Revision 1.1
Data D7 – D0 is moved
to Address A4..A0 here
23 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Figure 15. Protocol for Serial Data Write with Length = 4
EN
TX
1
1 0
A A A A A
4 3 2 1 0
D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
LEN1 LEN0
Command & Address
Phase
Data2 Phase
Data1 Phase
Data D7-D0 is
moved to Address
A4-A0 here
LEN1 = 1 LEN0 = 0
Length = 4
Data3 Phase
Data D7-D0 is
moved to Address
A4-A0 + 1 here
Data4 Phase
Data D7-D0 is
moved to Address
A4-A0 + 2 here
Data D7-D0 is
moved to Address
A4-A0 + 3 here
Read Command. For Read command RD/WR=1.
After the command code, length of the transfer is send in next two bits, the address of register to be read has to be provided from the MSB to the
LSB. Then one, two, four or eight data bytes can be transferred from the SPI slave to the master, always from the MSB to the LSB.
Each bit of the command and address sections of the frame have to be driven by the 2-Wire SP master on the SP clock (EN pin) positive edge
and the 2-Wire SP slave (device) samples this bit on the next SP clock (EN pin) negative edge. Each bit of the data phase of the frame has to be
driven by the 2-Wire SP slave (device) on the SP clock (EN pin) positive edge and the 2-Wire SP master samples this bit on the next SP clock
(EN pin) negative edge. The following figures illustrate two examples of read command (without and with address self-increment.)
Figure 16. Protocol for Serial Data Read with Length = 1
EN
TX
0
LEN1 LEN0
A4
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
Data Phase
Command & Address Phase
LEN1 = 0 LEN0 = 0
Length of Transaction = 1
Transfer edge
Sampling edge
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Data D7 – D0 at
address A4 ..A0 is
read here
Revision 1.1
Transfer edge
Sampling edge
24 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Figure 17. Protocol for Serial Data Read with Length = 4
EN
TX
1
D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
A A A A A
4 3 2 1 0
1 0
LEN1 LEN0
Command & Address
Data2 Phase
Data3 Phase
Data4 Phase
Data1 Phase
Phase
Data D7-D0 at
Data D7-D0 at
Data D7-D0 at
Data D7-D0 at
Data D7-D0 at
LEN1 = 1 LEN0 = 0
Address A4-A0
Address A4-A0 +1
Address A4-A0 +2
Address A4-A0 +3
Address A4-A0 +4
Length = 4
is read here
is read here
is read here
is read here
is read here
Timing. The following figures illustrate timing waveforms and parameters.
Figure 18. Timing for Writing
TENSCLK_H
TENSCLK_L
EN
TDI_SU
TDI_HD
DATAI
TX
DATAI
Figure 19. Timing for Reading
TENSCLK_H
TD0_D
TENSCLK_L
EN
TDI_SU
TX
TD0_D
TDI_HD
DATAI
DATAO
DATAO
TDI_HZ
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
25 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.8 Control and Diagnosis Registers
The serial interface can be used as interface between the ASSP AS8530 and an external micro-controller. The interface is a slave and only the
micro-controller can start the communication. This interface will be used for device configuration, entering into test mode and carrying out
diagnostic options. Refer to Table 8 for details on the configuration registers.
8.8.1
Definition of Control and Status Registers
A total of 32 control, diagnosis and test registers, each of 8-bit can be accessed using the 2-wire serial interface. Table 8 provides a description
of all control and status registers.
Table 8. Configuration Registers
Address
Register Name
POR Value
RD / WR
Description
Control and Configuration Register
D0 Reserved
D1 Reserved
D2 Reserved
0 x 03
Device Configuration
Register
On POR_VCC
0000_1111
RD / WR
D3 Enable / Disable LIN Transceiver
0
Disabled
1
Enabled
D7…D4 Reserved
0 x 04
Device Control Register
On POR_VSUP
0000_0001
RD / WR
D7... D1 Reserved
D0 Temporary shutdown control bit
0 x 05
Temporary Shutdown
Register
On POR_VCC
0000_0000
RD / WR
0
No Temporary shutdown
1
Enter into Temporary shutdown
D7…D1 Reserved
D0 Window Watch Dog Trigger
0 x 06
Window Watch Dog
Trigger Register
On POR_VCC
0000_0000
This bit will be set by MCU to indicate trigger event. If this trigger
occurs outside the Window of Watch dog counter, then RESET signal
is asserted. Also on this trigger WWD counter is restarted and this bit
will be cleared internally within 2 cycles of 128KHz clock.
WR
D7 … D1 Reserved
0 x 07
Low Side Driver Data
Register
On POR_VCC
0000_0000
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
RD / WR
D7 … D0 Reserved
Revision 1.1
26 - 32
AS8530
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Table 8. Configuration Registers
Address
Register Name
POR Value
RD / WR
Description
Diagnosis Register
D7..D0 = DR[7:0] 8 LSB bits of the 24 bit Diagnostic Register
D0 PORVSUP (set when VSUP < Vsuvr_on, cleared after µC read)
D1 UVVCC Under voltage VCC (set when VCC < Vuvr_on, cleared
after µC read)
D2 OTEMP160 Over-temperature Reset. (set when temp > Tsd,
cleared after µC read)
0 x 08
Diagnostic Register 1
On POR_VSUP
0000_0011
RD
D3 OTEMP140 Over-temperature warning (set when temp > Totset,
cleared after µC read)
D4 OVVBAT Overvoltage VBAT. (set when VSUP > Vovthh, cleared
after µC read)
D5 Reserved
D6 RWAKE Remote Wakeup (set on Remote Wakeup event on LIN
Bus, cleared after µC read)
D7 WWDT Window watchdog timeout. (set on failure of Window
watchdog timeout, cleared after µC read)
D7..D0 = DR[15:8] next 8 LSB bits of the 24 bit Diagnostic
Register.
0 x 09
Diagnostic Register 2
On POR_VSUP
0000_0000
RD
D0 TXTIMEOUT Tx timeout of 1sec. (set on TX low > 1sec,
cleared after µC read)
D1 TEMPSHUT this bit is set on entering into temporary
shutdown state and cleared after µC read.
D7 D2 Reserved
Note: When the device is powered ON @ ambient temperature of 125ºC, the status of the OVTEMP140 can be HIGH indicating an over
temperature warning. This is because 125ºC is within the limits for the OVTEMP140.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
27 - 32
AS8530
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
9 Package Drawings and Markings
The device is available in a ep-SOIC8 package.
Figure 20. Drawings and Dimensions
YYWWIZZ
AS8530*
* The device marking for the VCC=5V option will change to AS8530A.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
28 - 32
AS8530
Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s
Symbol
A
A1
A2
b
c
D
D1
E
E1
E2
e
L
Min
0.00
1.25
0.31
0.17
2.24
1.55
0.41
Nom
4.90 BSC
3.10
6.00 BSC
3.90 BSC
2.41
1.27 BSC
0.64
Max
1.70
0.15
0.51
0.25
3.20
2.51
0.89
Symbol
L1
L2
h
θ
aaa
bbb
ccc
ddd
eee
fff
N
Min
0.25
0º
-
Nom
1.04 REF
0.25 BSC
0.10
0.20
0.10
0.25
0.10
0.15
8
Max
0.50
8º
-
Notes:
1.
2.
3.
4.
Dimensions and tolerancing conform to ASME Y14.5M -1994.
All dimensions are in miilimeters. Angles are in degrees.
Datums A and B to be determined at datum H.
Extrusion of exposed area in bottom side is 0.20mm typical.
Marking: YYWWIZZ.
YY
WW
I
ZZ
Last two digits of the
manufacturing year
Manufacturing Week
Plant Identifier
Traceability Code
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
29 - 32
AS8530
Datasheet - R e v i s i o n H i s t o r y
Revision History
Revision
1.0
1.1
Date
Owner
Description
26 Nov, 2010
mbl
Initial release
29 Nov, 2010
kpt
Marking details updated under Ordering Information.
03 Jun, 2011
mbl
Updated Package Drawings and Markings, Ordering Information.
Note: Typos may not be explicitly mentioned under revision history.
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
30 - 32
AS8530
Datasheet - O r d e r i n g I n f o r m a t i o n
10 Ordering Information
The devices are available as the standard products shown in Table 9.
Table 9. Ordering Information
1
Ordering Code
Marking
Description
Delivery Form
Package
AS8530A-ASOT
AS8530-ASOT
AS8530A
VCC = 5V
Tape & Reel
ep-SOIC8
AS8530
VCC = 3.3V
Tape & Reel
ep-SOIC8
1. For both product versions, the RESET delay time tRes as well as undervoltage threshold are set to default value and window watchdog
is disabled. On special request, optional factory settings can be made available on specific vendor addendum.
Note: All products are RoHS compliant and austriamicrosystems green.
Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect
Technical Support is available at http://www.austriamicrosystems.com/Technical-Support
For further information and requests, please contact us mailto: [email protected]
or find your local distributor at http://www.austriamicrosystems.com/distributor
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
31 - 32
AS8530
Datasheet - C o p y r i g h t s
Copyrights
Copyright © 1997-2011, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®.
All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of
the copyright owner.
All products and companies mentioned are trademarks or registered trademarks of their respective companies.
Disclaimer
Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale.
austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding
the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at
any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for
current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range,
unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are
specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100
parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location.
The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not
be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use,
interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing,
performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of
austriamicrosystems AG rendering of technical or other services.
Contact Information
Headquarters
austriamicrosystems AG
Tobelbaderstrasse 30
A-8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
Fax: +43 (0) 3136 525 01
For Sales Offices, Distributors and Representatives, please visit:
http://www.austriamicrosystems.com/contact
www.austriamicrosystems.com/Lin_CompanionIC/AS8530
Revision 1.1
32 - 32
Similar pages