Hittite HMC344LP3 Gaas mmic sp4t non-reflective switch, dc - 8 ghz Datasheet

HMC344LP3 / 344LP3E
v06.1210
GaAs MMIC SP4T NON-REFLECTIVE
SWITCH, DC - 8 GHz
Typical Applications
Features
This switch is suitable for usage in DC - 8.0 GHz 50Ohm or 75-Ohm systems:
Broadband Performance: DC - 8 GHz
• Broadband
Low Insertion Loss: 1.8 dB@ 6 GHz
• Fiber Optics
Integrated 2:4 TTL Decoder
• Switched Filter Banks
16 Lead 3x3mm QFN Package: 9 mm²
High Isolation: 40 dB@ 6 GHz
• Wireless below 8 GHz
Functional Diagram
General Description
The HMC344LP3 & HMC344LP3E are broadband
non-reflective GaAs MESFET SP4T switches in low
cost leadless surface mount packages. Covering DC
to 8 GHz, this switch offers high isolation and low
insertion loss and extends the frequency coverage
of Hittite’s SP4T switch product line. This switch also
includes an on board binary decoder circuit which
reduces the required logic control lines to two. The
switch operates using a negative control voltage of
0/-5V, and requires a fixed bias of -5V.
Switches - multi-throw - SMT
15
15 - 1
Electrical Specifications, TA = +25° C, With 0/-5V Control, 50 Ohm System
Parameter
Frequency
Min.
Typ.
Max.
Units
1.6
1.8
2.1
2.0
2.2
2.5
dB
dB
dB
Insertion Loss
DC - 2.0 GHz
DC - 6.0 GHz
DC - 8.0 GHz
Isolation
DC - 2.0 GHz
DC - 4.0 GHz
DC - 6.0 GHz
DC - 8.0 GHz
43
36
34
31
48
41
40
36
dB
dB
dB
dB
12
9
8
5
15
12
11
8
dB
dB
dB
dB
Return Loss
“On State”
DC - 2.0 GHz
DC - 4.0 GHz
DC - 6.0 GHz
DC - 8.0 GHz
Return Loss
“Off State”
DC - 8.0 GHz
7
10
dB
Input Power for 1 dB Compression
0.5 - 8.0 GHz
17
21
dBm
Input Third Order Intercept
(Two-Tone Input Power = +7 dBm Each Tone)
0.5 - 8.0 GHz
37
40
dBm
Switching Characteristics
tRISE, tFALL (10/90% RF)
tON, tOFF (50% CTL to 10/90% RF)
DC - 8.0 GHz
35
150
ns
ns
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC344LP3 / 344LP3E
v06.1210
GaAs MMIC SP4T NON-REFLECTIVE
SWITCH, DC - 8 GHz
Insertion Loss vs. Temperature
Isolation
0
-10
-1
ISOLATION (dB)
-2
-3
+25 C
+85 C
-40 C
-4
RF1
RF2
RF3
RF4
-20
-30
-40
-50
-60
-5
-70
0
1
2
3
4
5
6
7
8
9
0
1
2
3
FREQUENCY (GHz)
Return Loss
6
7
8
9
10
25
INPUT COMPRESSION POINT (dBm)
RFC
RF1,2,3,4 On
RF1,2,3,4 Off
-5
RETURN LOSS (dB)
5
0.1 and 1 dB Input Compression Point
0
-10
-15
-20
15
22
19
16
1.0dB Compression Point
0.1dB Compression Point
13
10
-25
0
1
2
3
4
5
6
7
8
2
9
3
4
5
6
7
8
9
FREQUENCY (GHz)
FREQUENCY (GHz)
Bias Voltage & Current
Input Third Order Intercept Point
INPUT THIRD ORDER INTERCEPT (dBm)
4
FREQUENCY (GHz)
45
Vee Range = -5.0 Vdc ± 10%
43
Vee
(Vdc)
Iee (Typ.)
(mA)
Iee (Max.)
(mA)
-5.0
3.0
6.0
41
Control Voltages
39
RF1
RF2
RF3
RF4
37
35
1
2
3
4
5
6
7
8
State
Bias Condition
Low
-3V to 0 Vdc @ 60 µA Typical
High
-5 to -4.2 Vdc @ 5 µA Typical
9
FREQUENCY (GHz)
Switches - multi-throw - SMT
INSERTION LOSS (dB)
0
* Isolation is recorded above insertion loss & measured at output of switch.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
15 - 2
HMC344LP3 / 344LP3E
v06.1210
GaAs MMIC SP4T NON-REFLECTIVE
SWITCH, DC - 8 GHz
Absolute Maximum Ratings
Bias Voltage Range (Vee)
-7.0 Vdc
Control Voltage Range (A & B)
Vee -0.5V to +1.0 Vdc
Channel Temperature
150 °C
Thermal Resistance
(Insertion Loss Path)
143 °C/W
Thermal Resistance
(Terminated Path)
1,030 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
Maximum Input Power
+24 dBm
ESD Sensitivity (HBM)
Class 1A
Truth Table
Control Input
Signal Path State
A
B
RFCOM to:
High
High
RF1
Low
High
RF2
High
Low
RF3
Low
Low
RF4
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Switches - multi-throw - SMT
15
NOTES:
1.LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3.LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO
PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND
PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC344LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC344LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
344
XXXX
344
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
15 - 3
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC344LP3 / 344LP3E
v06.1210
GaAs MMIC SP4T NON-REFLECTIVE
SWITCH, DC - 8 GHz
Pin Descriptions
Function
Description
1, 4,
9, 12, 15
RF4, RF3, RF2,
RF1, RFC
This pin is DC coupled and matched to 50 Ohm. Blocking
capacitors are required if RF line potential is not equal to 0V.
2, 3,
10, 11, 13
N/C
This pin should be connected to PCB RF
ground to maximize isolation.
5, 14, 16
GND
Package bottom has exposed metal paddle that
must also be connected to PCB RF ground.
6
VEE
Supply Voltage -5V ± 10%
7
CTLB
See truth table and control voltage table.
8
CTLA
See truth table and control voltage table.
Interface Schematic
15
Switches - multi-throw - SMT
Pin Number
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
15 - 4
HMC344LP3 / 344LP3E
v06.1210
GaAs MMIC SP4T NON-REFLECTIVE
SWITCH, DC - 8 GHz
TTL Interface Circuit
Switches - multi-throw - SMT
15
15 - 5
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC344LP3 / 344LP3E
v06.1210
GaAs MMIC SP4T NON-REFLECTIVE
SWITCH, DC - 8 GHz
Evaluation PCB
List of Materials for Evaluation PCB 105311
Item
Description
J1 - J7
PCB Mount SMA RF Connector
J8 - J11
DC Pin
C1 - C7
0 ohm res, 0402 Pkg. [3]
C8
10k pF Capacitor, 0603 Pkg.
U1
HMC344LP3 / HMC344LP3E
SP4T Switch
PCB [2]
104708 Evaluation PCB 1.29”x1.55”
[1] Reference this number when ordering complete evaluation PCB
[1]
The circuit board used in the final application
should be generated with proper RF circuit design
techniques. Signal lines at the RF port should have
50 ohm impedance and the package ground leads
and backside ground slug should be connected
directly to the ground plane similar to that shown
above. The evaluation circuit board shown above is
available from Hittite Microwave Corporation upon
request.
[2] Circuit Board Material: Rogers 4350
[3] Select and replace with a suitable capacitor value for applicable
operating frequency range.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
Switches - multi-throw - SMT
15
15 - 6
Similar pages