ACT ACTF474S/374.0/QCC8C Characteristics of saw filter Datasheet

Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
This specification shall cover the characteristics of SAW Filter
ACTF474S/374.0/QCC8C. The device is packaged in the popular QCC8C package
and has a centre frequency of 374.0MHz
1.Package Dimension (QCC8C)
2.
Pins
Configuration
2
Input Ground
3
Input
6
Output Ground
7
Output
1,5
To be Grounded
4,8
Case Ground
Sign
Data (unit: mm)
Sign
Data (unit: mm)
A
2.08
E
1.20
B
0.60
F
1.35
C
1.27
G
5.00
D
2.54
H
5.00
3. Matching network (Element values may depend on PCB layout)
50 Ω unbalanced:
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
1 OF 5
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
250 Ω balanced:
200 Ω balanced:
4. Typical Response
Wide band
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
2 OF 5
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
Narrow band
Delay Ripple
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
3 OF 5
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
5.Performance
5-1. Maximum Ratings
Value
Units
Source Power
Rating
PS
10
dBm
DC Voltage
VDC
0
V
-40 to +85
°C
+235
°C
Storage Temperature
Soldering Temperature
5-2. Electronic Characteristics
Operating temperature:
TA = -10 … +80 °C Terminating source impedance:
ZS = 50 Ω unbalanced and matching network
Terminating load impedance:
ZL = 50 Ω unbalanced and matching network
Characteristics
Centre Frequency
fC
Minimum insertion attenuation
(including matching network)
αmin
Bandwidth
αrel≤3 dB
BW 3dB
Minimum
Typical
Maximum
Units
--
374.000
--
MHz
--
8.5
10.0
dB
17
22
--
MHz
Amplitude ripple (p-p)
f C±7MHz
Δα
--
0.5
1.0
dB
Group delay ripple (p-p)
f C±7MHz
Δτ
--
40
100
ns
30
40
--
dB
30
40
48
20
30
38
40
42
45
52
38
42
44
45
--------
dB
dB
dB
dB
dB
dB
dB
--
-87
--
ppm/K
Triple transit suppression
Relative attenuation (relative to αmin)
357.5 ~ 352.0 MHz
352.0 ~ 341.0 MHz
341.0 ~ 224.0 MHz
390.5 ~ 392.0 MHz
392.0 ~ 396.0 MHz
396.0 ~ 422.0 MHz
422.0 ~ 454.0 MHz
Temperature coefficient of frequency
αrel
T Cf
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
4 OF 5
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
iCAUTION: Electrostatic Sensitive Device. Observe precautions for handling!
1.
2.
3.
4.
5.
6.
The frequency f C is defined as the midpoint between the 3dB frequencies.
Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture that is
connected to a 50 Ω test system with VSWR ≤1.2:1. The test fixture L and C are adjusted for minimum insertion
loss at the filter centre frequency, f C. Note that insertion loss, bandwidth, and passband shape are dependent on
the impedance matching component values and quality.
Unless noted otherwise, specifications apply over the entire specified operating temperature range.
The specifications of this device are based on the test circuit shown above and subject to change or
obsolescence without notice.
All equipment designs utilizing this product must be approved by the appropriate government agency prior to
manufacture or sale.
Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications,
processes and circuits implemented within components or assemblies.
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
5 OF 5
Issue : 1 C1
Date : SEPT 04
Similar pages